From fc99fe0618f355b708ce88fedaca9783072ac3d5 Mon Sep 17 00:00:00 2001 From: Stephen Hemminger Date: Mon, 4 Jun 2007 17:23:22 -0700 Subject: [PATCH] sky2: Add PCI device specfic register 4 & 5 Need to setup more PCI control control registers are on Yukon EX. Some of these also exist on Yukon EC-U as well. Signed-off-by: Stephen Hemminger Signed-off-by: Jeff Garzik --- drivers/net/sky2.c | 18 +++++++---- drivers/net/sky2.h | 77 ++++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 89 insertions(+), 6 deletions(-) diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index 612257172b..0bd74fe5c3 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -217,13 +217,19 @@ static void sky2_power_on(struct sky2_hw *hw) sky2_write8(hw, B2_Y2_CLK_GATE, 0); if (hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX) { - u32 reg1; + u32 reg; - sky2_pci_write32(hw, PCI_DEV_REG3, 0); - reg1 = sky2_pci_read32(hw, PCI_DEV_REG4); - reg1 &= P_ASPM_CONTROL_MSK; - sky2_pci_write32(hw, PCI_DEV_REG4, reg1); - sky2_pci_write32(hw, PCI_DEV_REG5, 0); + reg = sky2_pci_read32(hw, PCI_DEV_REG4); + /* set all bits to 0 except bits 15..12 and 8 */ + reg &= P_ASPM_CONTROL_MSK; + sky2_pci_write32(hw, PCI_DEV_REG4, reg); + + reg = sky2_pci_read32(hw, PCI_DEV_REG5); + /* set all bits to 0 except bits 28 & 27 */ + reg &= P_CTL_TIM_VMAIN_AV_MSK; + sky2_pci_write32(hw, PCI_DEV_REG5, reg); + + sky2_pci_write32(hw, PCI_CFG_REG_1, 0); } } diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h index b8c4a3b5ea..3caeddf893 100644 --- a/drivers/net/sky2.h +++ b/drivers/net/sky2.h @@ -14,6 +14,8 @@ enum { PCI_DEV_REG3 = 0x80, PCI_DEV_REG4 = 0x84, PCI_DEV_REG5 = 0x88, + PCI_CFG_REG_0 = 0x90, + PCI_CFG_REG_1 = 0x94, }; enum { @@ -28,6 +30,7 @@ enum { enum pci_dev_reg_1 { PCI_Y2_PIG_ENA = 1<<31, /* Enable Plug-in-Go (YUKON-2) */ PCI_Y2_DLL_DIS = 1<<30, /* Disable PCI DLL (YUKON-2) */ + PCI_SW_PWR_ON_RST= 1<<30, /* SW Power on Reset (Yukon-EX) */ PCI_Y2_PHY2_COMA = 1<<29, /* Set PHY 2 to Coma Mode (YUKON-2) */ PCI_Y2_PHY1_COMA = 1<<28, /* Set PHY 1 to Coma Mode (YUKON-2) */ PCI_Y2_PHY2_POWD = 1<<27, /* Set PHY 2 to Power Down (YUKON-2) */ @@ -67,6 +70,80 @@ enum pci_dev_reg_4 { | P_ASPM_CLKRUN_REQUEST | P_ASPM_INT_FIFO_EMPTY, }; +/* PCI_OUR_REG_5 32 bit Our Register 5 (Yukon-ECU only) */ +enum pci_dev_reg_5 { + /* Bit 31..27: for A3 & later */ + P_CTL_DIV_CORE_CLK_ENA = 1<<31, /* Divide Core Clock Enable */ + P_CTL_SRESET_VMAIN_AV = 1<<30, /* Soft Reset for Vmain_av De-Glitch */ + P_CTL_BYPASS_VMAIN_AV = 1<<29, /* Bypass En. for Vmain_av De-Glitch */ + P_CTL_TIM_VMAIN_AV_MSK = 3<<27, /* Bit 28..27: Timer Vmain_av Mask */ + /* Bit 26..16: Release Clock on Event */ + P_REL_PCIE_RST_DE_ASS = 1<<26, /* PCIe Reset De-Asserted */ + P_REL_GPHY_REC_PACKET = 1<<25, /* GPHY Received Packet */ + P_REL_INT_FIFO_N_EMPTY = 1<<24, /* Internal FIFO Not Empty */ + P_REL_MAIN_PWR_AVAIL = 1<<23, /* Main Power Available */ + P_REL_CLKRUN_REQ_REL = 1<<22, /* CLKRUN Request Release */ + P_REL_PCIE_RESET_ASS = 1<<21, /* PCIe Reset Asserted */ + P_REL_PME_ASSERTED = 1<<20, /* PME Asserted */ + P_REL_PCIE_EXIT_L1_ST = 1<<19, /* PCIe Exit L1 State */ + P_REL_LOADER_NOT_FIN = 1<<18, /* EPROM Loader Not Finished */ + P_REL_PCIE_RX_EX_IDLE = 1<<17, /* PCIe Rx Exit Electrical Idle State */ + P_REL_GPHY_LINK_UP = 1<<16, /* GPHY Link Up */ + + /* Bit 10.. 0: Mask for Gate Clock */ + P_GAT_PCIE_RST_ASSERTED = 1<<10,/* PCIe Reset Asserted */ + P_GAT_GPHY_N_REC_PACKET = 1<<9, /* GPHY Not Received Packet */ + P_GAT_INT_FIFO_EMPTY = 1<<8, /* Internal FIFO Empty */ + P_GAT_MAIN_PWR_N_AVAIL = 1<<7, /* Main Power Not Available */ + P_GAT_CLKRUN_REQ_REL = 1<<6, /* CLKRUN Not Requested */ + P_GAT_PCIE_RESET_ASS = 1<<5, /* PCIe Reset Asserted */ + P_GAT_PME_DE_ASSERTED = 1<<4, /* PME De-Asserted */ + P_GAT_PCIE_ENTER_L1_ST = 1<<3, /* PCIe Enter L1 State */ + P_GAT_LOADER_FINISHED = 1<<2, /* EPROM Loader Finished */ + P_GAT_PCIE_RX_EL_IDLE = 1<<1, /* PCIe Rx Electrical Idle State */ + P_GAT_GPHY_LINK_DOWN = 1<<0, /* GPHY Link Down */ + + PCIE_OUR5_EVENT_CLK_D3_SET = P_REL_GPHY_REC_PACKET | + P_REL_INT_FIFO_N_EMPTY | + P_REL_PCIE_EXIT_L1_ST | + P_REL_PCIE_RX_EX_IDLE | + P_GAT_GPHY_N_REC_PACKET | + P_GAT_INT_FIFO_EMPTY | + P_GAT_PCIE_ENTER_L1_ST | + P_GAT_PCIE_RX_EL_IDLE, +}; + +#/* PCI_CFG_REG_1 32 bit Config Register 1 (Yukon-Ext only) */ +enum pci_cfg_reg1 { + P_CF1_DIS_REL_EVT_RST = 1<<24, /* Dis. Rel. Event during PCIE reset */ + /* Bit 23..21: Release Clock on Event */ + P_CF1_REL_LDR_NOT_FIN = 1<<23, /* EEPROM Loader Not Finished */ + P_CF1_REL_VMAIN_AVLBL = 1<<22, /* Vmain available */ + P_CF1_REL_PCIE_RESET = 1<<21, /* PCI-E reset */ + /* Bit 20..18: Gate Clock on Event */ + P_CF1_GAT_LDR_NOT_FIN = 1<<20, /* EEPROM Loader Finished */ + P_CF1_GAT_PCIE_RX_IDLE = 1<<19, /* PCI-E Rx Electrical idle */ + P_CF1_GAT_PCIE_RESET = 1<<18, /* PCI-E Reset */ + P_CF1_PRST_PHY_CLKREQ = 1<<17, /* Enable PCI-E rst & PM2PHY gen. CLKREQ */ + P_CF1_PCIE_RST_CLKREQ = 1<<16, /* Enable PCI-E rst generate CLKREQ */ + + P_CF1_ENA_CFG_LDR_DONE = 1<<8, /* Enable core level Config loader done */ + + P_CF1_ENA_TXBMU_RD_IDLE = 1<<1, /* Enable TX BMU Read IDLE for ASPM */ + P_CF1_ENA_TXBMU_WR_IDLE = 1<<0, /* Enable TX BMU Write IDLE for ASPM */ + + PCIE_CFG1_EVENT_CLK_D3_SET = P_CF1_DIS_REL_EVT_RST | + P_CF1_REL_LDR_NOT_FIN | + P_CF1_REL_VMAIN_AVLBL | + P_CF1_REL_PCIE_RESET | + P_CF1_GAT_LDR_NOT_FIN | + P_CF1_GAT_PCIE_RESET | + P_CF1_PRST_PHY_CLKREQ | + P_CF1_ENA_CFG_LDR_DONE | + P_CF1_ENA_TXBMU_RD_IDLE | + P_CF1_ENA_TXBMU_WR_IDLE, +}; + #define PCI_STATUS_ERROR_BITS (PCI_STATUS_DETECTED_PARITY | \ PCI_STATUS_SIG_SYSTEM_ERROR | \ -- 2.39.5