From e56a99d5a42dcb91e622ae7a0289d8fb2ddabffb Mon Sep 17 00:00:00 2001 From: Artem Bityutskiy Date: Mon, 14 Jul 2008 19:08:34 +0300 Subject: [PATCH] UBIFS: add brief documentation Signed-off-by: Artem Bityutskiy Signed-off-by: Adrian Hunter --- Documentation/filesystems/ubifs.txt | 164 ++++++++++++++++++++++++++++ 1 file changed, 164 insertions(+) create mode 100644 Documentation/filesystems/ubifs.txt diff --git a/Documentation/filesystems/ubifs.txt b/Documentation/filesystems/ubifs.txt new file mode 100644 index 0000000000..540e9e7f59 --- /dev/null +++ b/Documentation/filesystems/ubifs.txt @@ -0,0 +1,164 @@ +Introduction +============= + +UBIFS file-system stands for UBI File System. UBI stands for "Unsorted +Block Images". UBIFS is a flash file system, which means it is designed +to work with flash devices. It is important to understand, that UBIFS +is completely different to any traditional file-system in Linux, like +Ext2, XFS, JFS, etc. UBIFS represents a separate class of file-systems +which work with MTD devices, not block devices. The other Linux +file-system of this class is JFFS2. + +To make it more clear, here is a small comparison of MTD devices and +block devices. + +1 MTD devices represent flash devices and they consist of eraseblocks of + rather large size, typically about 128KiB. Block devices consist of + small blocks, typically 512 bytes. +2 MTD devices support 3 main operations - read from some offset within an + eraseblock, write to some offset within an eraseblock, and erase a whole + eraseblock. Block devices support 2 main operations - read a whole + block and write a whole block. +3 The whole eraseblock has to be erased before it becomes possible to + re-write its contents. Blocks may be just re-written. +4 Eraseblocks become worn out after some number of erase cycles - + typically 100K-1G for SLC NAND and NOR flashes, and 1K-10K for MLC + NAND flashes. Blocks do not have the wear-out property. +5 Eraseblocks may become bad (only on NAND flashes) and software should + deal with this. Blocks on hard drives typically do not become bad, + because hardware has mechanisms to substitute bad blocks, at least in + modern LBA disks. + +It should be quite obvious why UBIFS is very different to traditional +file-systems. + +UBIFS works on top of UBI. UBI is a separate software layer which may be +found in drivers/mtd/ubi. UBI is basically a volume management and +wear-leveling layer. It provides so called UBI volumes which is a higher +level abstraction than a MTD device. The programming model of UBI devices +is very similar to MTD devices - they still consist of large eraseblocks, +they have read/write/erase operations, but UBI devices are devoid of +limitations like wear and bad blocks (items 4 and 5 in the above list). + +In a sense, UBIFS is a next generation of JFFS2 file-system, but it is +very different and incompatible to JFFS2. The following are the main +differences. + +* JFFS2 works on top of MTD devices, UBIFS depends on UBI and works on + top of UBI volumes. +* JFFS2 does not have on-media index and has to build it while mounting, + which requires full media scan. UBIFS maintains the FS indexing + information on the flash media and does not require full media scan, + so it mounts many times faster than JFFS2. +* JFFS2 is a write-through file-system, while UBIFS supports write-back, + which makes UBIFS much faster on writes. + +Similarly to JFFS2, UBIFS supports on-the-flight compression which makes +it possible to fit quite a lot of data to the flash. + +Similarly to JFFS2, UBIFS is tolerant of unclean reboots and power-cuts. +It does not need stuff like ckfs.ext2. UBIFS automatically replays its +journal and recovers from crashes, ensuring that the on-flash data +structures are consistent. + +UBIFS scales logarithmically (most of the data structures it uses are +trees), so the mount time and memory consumption do not linearly depend +on the flash size, like in case of JFFS2. This is because UBIFS +maintains the FS index on the flash media. However, UBIFS depends on +UBI, which scales linearly. So overall UBI/UBIFS stack scales linearly. +Nevertheless, UBI/UBIFS scales considerably better than JFFS2. + +The authors of UBIFS believe, that it is possible to develop UBI2 which +would scale logarithmically as well. UBI2 would support the same API as UBI, +but it would be binary incompatible to UBI. So UBIFS would not need to be +changed to use UBI2 + + +Mount options +============= + +(*) == default. + +norm_unmount (*) commit on unmount; the journal is committed + when the file-system is unmounted so that the + next mount does not have to replay the journal + and it becomes very fast; +fast_unmount do not commit on unmount; this option makes + unmount faster, but the next mount slower + because of the need to replay the journal. + + +Quick usage instructions +======================== + +The UBI volume to mount is specified using "ubiX_Y" or "ubiX:NAME" syntax, +where "X" is UBI device number, "Y" is UBI volume number, and "NAME" is +UBI volume name. + +Mount volume 0 on UBI device 0 to /mnt/ubifs: +$ mount -t ubifs ubi0_0 /mnt/ubifs + +Mount "rootfs" volume of UBI device 0 to /mnt/ubifs ("rootfs" is volume +name): +$ mount -t ubifs ubi0:rootfs /mnt/ubifs + +The following is an example of the kernel boot arguments to attach mtd0 +to UBI and mount volume "rootfs": +ubi.mtd=0 root=ubi0:rootfs rootfstype=ubifs + + +Module Parameters for Debugging +=============================== + +When UBIFS has been compiled with debugging enabled, there are 3 module +parameters that are available to control aspects of testing and debugging. +The parameters are unsigned integers where each bit controls an option. +The parameters are: + +debug_msgs Selects which debug messages to display, as follows: + + Message Type Flag value + + General messages 1 + Journal messages 2 + Mount messages 4 + Commit messages 8 + LEB search messages 16 + Budgeting messages 32 + Garbage collection messages 64 + Tree Node Cache (TNC) messages 128 + LEB properties (lprops) messages 256 + Input/output messages 512 + Log messages 1024 + Scan messages 2048 + Recovery messages 4096 + +debug_chks Selects extra checks that UBIFS can do while running: + + Check Flag value + + General checks 1 + Check Tree Node Cache (TNC) 2 + Check indexing tree size 4 + Check orphan area 8 + Check old indexing tree 16 + Check LEB properties (lprops) 32 + Check leaf nodes and inodes 64 + +debug_tsts Selects a mode of testing, as follows: + + Test mode Flag value + + Force in-the-gaps method 2 + Failure mode for recovery testing 4 + +For example, set debug_msgs to 5 to display General messages and Mount +messages. + + +References +========== + +UBIFS documentation and FAQ/HOWTO at the MTD web site: +http://www.linux-mtd.infradead.org/doc/ubifs.html +http://www.linux-mtd.infradead.org/faq/ubifs.html -- 2.39.5