From cd08d0754ecb0cb9293c8476cb33ded1d23d0d8f Mon Sep 17 00:00:00 2001 From: "Maciej W. Rozycki" Date: Thu, 19 Jun 2008 00:39:33 +0100 Subject: [PATCH] x86: fix IO APIC breakage on HP nx6325 On Thu, 19 Jun 2008, Rafael J. Wysocki wrote: > > With such a configuration the "x86: I/O APIC: timer through 8259A > > second-chance" patch should not matter, because the only change it > > introduces is an attempt to try the same I/O APIC pin again, but with the > > IRQ0 line of the master 8259A enabled. That's not a terribly unusual > > configuration and nothing should get confused in the system. > > But it _does_ get confused, really. Something certainly gets confused, but so far I am not sure which bit exactly it is, are you? > > Barring the unlikely possibility of the 8259A actually being wired to > > INTIN2 of the I/O APIC I can see two possible explanations: > > > > 1. The 8259A interrupt actually escapes to the CPU somehow and is handled > > as an ExtINTA interrupt. This would make the code in check_timer() > > decide it has found a working configuration, while actually it has been > > fooled. [...] > Here you go: > > [ 0.108006] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 > [ 0.108006] ..MP-BIOS bug: 8254 timer not connected to IO-APIC > [ 0.108006] ...trying to set up timer (IRQ0) through the 8259A ... <3> > [ 0.108006] ..... (found apic 0 pin 2) ...<3> works. > > The full dmesg is at: http://www.sisk.pl/kernel/debug/20080618/dmesg-1.log Thanks. In this case I suspect the case #1 quoted above happens, that is the 8259A manages to deliver its interrupt somehow. Note at this stage it is meant to be in the AEOI mode, so it can happily resubmit the interrupt indefinitely with no additional handling as long as it receives INTA cycles. Can you please try the patch below on top of "x86: I/O APIC: timer through 8259A second-chance" to see whether my hypothesis is true? It modifies the through-8259A setup path so that the APIC input gets masked, but the 8259A has the timer interrupt still enabled. Let me know how the timer interrupt is routed in this case. Bisected-by: "Rafael J. Wysocki" Tested-by: "Rafael J. Wysocki" Signed-off-by: Ingo Molnar --- arch/x86/kernel/io_apic_64.c | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/x86/kernel/io_apic_64.c b/arch/x86/kernel/io_apic_64.c index 60a022d6de..f06f5b4fb3 100644 --- a/arch/x86/kernel/io_apic_64.c +++ b/arch/x86/kernel/io_apic_64.c @@ -1715,6 +1715,7 @@ static inline void __init check_timer(void) /* replace_pin_at_irq(0, apic1, pin1, apic2, pin2); */ setup_timer_IRQ0_pin(apic2, pin2, cfg->vector); unmask_IO_APIC_irq(0); + clear_IO_APIC_pin(apic2, pin2); enable_8259A_irq(0); if (timer_irq_works()) { apic_printk(APIC_VERBOSE," works.\n"); -- 2.39.5