From ad8c623f4f48085edd51c7f4cdfd10295547bf45 Mon Sep 17 00:00:00 2001 From: David Brownell Date: Sat, 30 Jun 2007 06:30:04 -0700 Subject: [PATCH] USB: pxa2xx_udc -- cleanups, mostly removing dma hooks Cleanups to the pxa2xx_udc code: - Primarily removing unused DMA hooks. - One "sparse" warning removed - Remove some Lubbock-only LED hooks (for debugging) That DMA code was never really completed. It worked, mostly, for IN transfers (to the host) if they were fortuitously aligned, but that code was never fully tested. And it was never coded for OUT transfers (which is where DMA would really help) ... because of chip errata on essentially every chip other than the pxa255, and because of design botches (nothing automated data toggle). So it's effectively been dead code for several years now ... no point in keeping it around. Signed-off-by: David Brownell Signed-off-by: Greg Kroah-Hartman --- drivers/usb/gadget/pxa2xx_udc.c | 387 ++------------------------------ drivers/usb/gadget/pxa2xx_udc.h | 42 +--- 2 files changed, 25 insertions(+), 404 deletions(-) diff --git a/drivers/usb/gadget/pxa2xx_udc.c b/drivers/usb/gadget/pxa2xx_udc.c index c9ec0b3e58..484de6e976 100644 --- a/drivers/usb/gadget/pxa2xx_udc.c +++ b/drivers/usb/gadget/pxa2xx_udc.c @@ -24,7 +24,6 @@ * */ -#undef DEBUG // #define VERBOSE DBG_VERBOSE #include @@ -75,9 +74,17 @@ * it constrains the sorts of USB configuration change events that work. * The errata for these chips are misleading; some "fixed" bugs from * pxa250 a0/a1 b0/b1/b2 sure act like they're still there. + * + * Note that the UDC hardware supports DMA (except on IXP) but that's + * not used here. IN-DMA (to host) is simple enough, when the data is + * suitably aligned (16 bytes) ... the network stack doesn't do that, + * other software can. OUT-DMA is buggy in most chip versions, as well + * as poorly designed (data toggle not automatic). So this driver won't + * bother using DMA. (Mostly-working IN-DMA support was available in + * kernels before 2.6.23, but was never enabled or well tested.) */ -#define DRIVER_VERSION "4-May-2005" +#define DRIVER_VERSION "30-June-2007" #define DRIVER_DESC "PXA 25x USB Device Controller driver" @@ -86,12 +93,9 @@ static const char driver_name [] = "pxa2xx_udc"; static const char ep0name [] = "ep0"; -// #define USE_DMA -// #define USE_OUT_DMA // #define DISABLE_TEST_MODE #ifdef CONFIG_ARCH_IXP4XX -#undef USE_DMA /* cpu-specific register addresses are compiled in to this code */ #ifdef CONFIG_ARCH_PXA @@ -103,25 +107,6 @@ static const char ep0name [] = "ep0"; #include "pxa2xx_udc.h" -#ifdef USE_DMA -static int use_dma = 1; -module_param(use_dma, bool, 0); -MODULE_PARM_DESC (use_dma, "true to use dma"); - -static void dma_nodesc_handler (int dmach, void *_ep); -static void kick_dma(struct pxa2xx_ep *ep, struct pxa2xx_request *req); - -#ifdef USE_OUT_DMA -#define DMASTR " (dma support)" -#else -#define DMASTR " (dma in)" -#endif - -#else /* !USE_DMA */ -#define DMASTR " (pio only)" -#undef USE_OUT_DMA -#endif - #ifdef CONFIG_USB_PXA2XX_SMALL #define SIZE_STR " (small)" #else @@ -280,9 +265,8 @@ static int pxa2xx_ep_enable (struct usb_ep *_ep, } ep->desc = desc; - ep->dma = -1; ep->stopped = 0; - ep->pio_irqs = ep->dma_irqs = 0; + ep->pio_irqs = 0; ep->ep.maxpacket = le16_to_cpu (desc->wMaxPacketSize); /* flush fifo (mostly for OUT buffers) */ @@ -290,30 +274,6 @@ static int pxa2xx_ep_enable (struct usb_ep *_ep, /* ... reset halt state too, if we could ... */ -#ifdef USE_DMA - /* for (some) bulk and ISO endpoints, try to get a DMA channel and - * bind it to the endpoint. otherwise use PIO. - */ - switch (ep->bmAttributes) { - case USB_ENDPOINT_XFER_ISOC: - if (le16_to_cpu(desc->wMaxPacketSize) % 32) - break; - // fall through - case USB_ENDPOINT_XFER_BULK: - if (!use_dma || !ep->reg_drcmr) - break; - ep->dma = pxa_request_dma ((char *)_ep->name, - (le16_to_cpu (desc->wMaxPacketSize) > 64) - ? DMA_PRIO_MEDIUM /* some iso */ - : DMA_PRIO_LOW, - dma_nodesc_handler, ep); - if (ep->dma >= 0) { - *ep->reg_drcmr = DRCMR_MAPVLD | ep->dma; - DMSG("%s using dma%d\n", _ep->name, ep->dma); - } - } -#endif - DBG(DBG_VERBOSE, "enabled %s\n", _ep->name); return 0; } @@ -333,14 +293,6 @@ static int pxa2xx_ep_disable (struct usb_ep *_ep) nuke (ep, -ESHUTDOWN); -#ifdef USE_DMA - if (ep->dma >= 0) { - *ep->reg_drcmr = 0; - pxa_free_dma (ep->dma); - ep->dma = -1; - } -#endif - /* flush fifo (mostly for IN buffers) */ pxa2xx_ep_fifo_flush (_ep); @@ -390,11 +342,6 @@ pxa2xx_ep_free_request (struct usb_ep *_ep, struct usb_request *_req) } -/* PXA cache needs flushing with DMA I/O (it's dma-incoherent), but there's - * no device-affinity and the heap works perfectly well for i/o buffers. - * It wastes much less memory than dma_alloc_coherent() would, and even - * prevents cacheline (32 bytes wide) sharing problems. - */ static void * pxa2xx_ep_alloc_buffer(struct usb_ep *_ep, unsigned bytes, dma_addr_t *dma, gfp_t gfp_flags) @@ -403,11 +350,7 @@ pxa2xx_ep_alloc_buffer(struct usb_ep *_ep, unsigned bytes, retval = kmalloc (bytes, gfp_flags & ~(__GFP_DMA|__GFP_HIGHMEM)); if (retval) -#ifdef USE_DMA - *dma = virt_to_bus (retval); -#else *dma = (dma_addr_t)~0; -#endif return retval; } @@ -517,18 +460,8 @@ write_fifo (struct pxa2xx_ep *ep, struct pxa2xx_request *req) /* requests complete when all IN data is in the FIFO */ if (is_last) { done (ep, req, 0); - if (list_empty(&ep->queue) || unlikely(ep->dma >= 0)) { + if (list_empty(&ep->queue)) pio_irq_disable (ep->bEndpointAddress); -#ifdef USE_DMA - /* unaligned data and zlps couldn't use dma */ - if (unlikely(!list_empty(&ep->queue))) { - req = list_entry(ep->queue.next, - struct pxa2xx_request, queue); - kick_dma(ep,req); - return 0; - } -#endif - } return 1; } @@ -727,182 +660,6 @@ read_ep0_fifo (struct pxa2xx_ep *ep, struct pxa2xx_request *req) return 0; } -#ifdef USE_DMA - -#define MAX_IN_DMA ((DCMD_LENGTH + 1) - BULK_FIFO_SIZE) - -static void -start_dma_nodesc(struct pxa2xx_ep *ep, struct pxa2xx_request *req, int is_in) -{ - u32 dcmd = req->req.length; - u32 buf = req->req.dma; - u32 fifo = io_v2p ((u32)ep->reg_uddr); - - /* caller guarantees there's a packet or more remaining - * - IN may end with a short packet (TSP set separately), - * - OUT is always full length - */ - buf += req->req.actual; - dcmd -= req->req.actual; - ep->dma_fixup = 0; - - /* no-descriptor mode can be simple for bulk-in, iso-in, iso-out */ - DCSR(ep->dma) = DCSR_NODESC; - if (is_in) { - DSADR(ep->dma) = buf; - DTADR(ep->dma) = fifo; - if (dcmd > MAX_IN_DMA) - dcmd = MAX_IN_DMA; - else - ep->dma_fixup = (dcmd % ep->ep.maxpacket) != 0; - dcmd |= DCMD_BURST32 | DCMD_WIDTH1 - | DCMD_FLOWTRG | DCMD_INCSRCADDR; - } else { -#ifdef USE_OUT_DMA - DSADR(ep->dma) = fifo; - DTADR(ep->dma) = buf; - if (ep->bmAttributes != USB_ENDPOINT_XFER_ISOC) - dcmd = ep->ep.maxpacket; - dcmd |= DCMD_BURST32 | DCMD_WIDTH1 - | DCMD_FLOWSRC | DCMD_INCTRGADDR; -#endif - } - DCMD(ep->dma) = dcmd; - DCSR(ep->dma) = DCSR_RUN | DCSR_NODESC - | (unlikely(is_in) - ? DCSR_STOPIRQEN /* use dma_nodesc_handler() */ - : 0); /* use handle_ep() */ -} - -static void kick_dma(struct pxa2xx_ep *ep, struct pxa2xx_request *req) -{ - int is_in = ep->bEndpointAddress & USB_DIR_IN; - - if (is_in) { - /* unaligned tx buffers and zlps only work with PIO */ - if ((req->req.dma & 0x0f) != 0 - || unlikely((req->req.length - req->req.actual) - == 0)) { - pio_irq_enable(ep->bEndpointAddress); - if ((*ep->reg_udccs & UDCCS_BI_TFS) != 0) - (void) write_fifo(ep, req); - } else { - start_dma_nodesc(ep, req, USB_DIR_IN); - } - } else { - if ((req->req.length - req->req.actual) < ep->ep.maxpacket) { - DMSG("%s short dma read...\n", ep->ep.name); - /* we're always set up for pio out */ - read_fifo (ep, req); - } else { - *ep->reg_udccs = UDCCS_BO_DME - | (*ep->reg_udccs & UDCCS_BO_FST); - start_dma_nodesc(ep, req, USB_DIR_OUT); - } - } -} - -static void cancel_dma(struct pxa2xx_ep *ep) -{ - struct pxa2xx_request *req; - u32 tmp; - - if (DCSR(ep->dma) == 0 || list_empty(&ep->queue)) - return; - - DCSR(ep->dma) = 0; - while ((DCSR(ep->dma) & DCSR_STOPSTATE) == 0) - cpu_relax(); - - req = list_entry(ep->queue.next, struct pxa2xx_request, queue); - tmp = DCMD(ep->dma) & DCMD_LENGTH; - req->req.actual = req->req.length - (tmp & DCMD_LENGTH); - - /* the last tx packet may be incomplete, so flush the fifo. - * FIXME correct req.actual if we can - */ - if (ep->bEndpointAddress & USB_DIR_IN) - *ep->reg_udccs = UDCCS_BI_FTF; -} - -/* dma channel stopped ... normal tx end (IN), or on error (IN/OUT) */ -static void dma_nodesc_handler(int dmach, void *_ep) -{ - struct pxa2xx_ep *ep = _ep; - struct pxa2xx_request *req; - u32 tmp, completed; - - local_irq_disable(); - - req = list_entry(ep->queue.next, struct pxa2xx_request, queue); - - ep->dma_irqs++; - ep->dev->stats.irqs++; - HEX_DISPLAY(ep->dev->stats.irqs); - - /* ack/clear */ - tmp = DCSR(ep->dma); - DCSR(ep->dma) = tmp; - if ((tmp & DCSR_STOPSTATE) == 0 - || (DDADR(ep->dma) & DDADR_STOP) != 0) { - DBG(DBG_VERBOSE, "%s, dcsr %08x ddadr %08x\n", - ep->ep.name, DCSR(ep->dma), DDADR(ep->dma)); - goto done; - } - DCSR(ep->dma) = 0; /* clear DCSR_STOPSTATE */ - - /* update transfer status */ - completed = tmp & DCSR_BUSERR; - if (ep->bEndpointAddress & USB_DIR_IN) - tmp = DSADR(ep->dma); - else - tmp = DTADR(ep->dma); - req->req.actual = tmp - req->req.dma; - - /* FIXME seems we sometimes see partial transfers... */ - - if (unlikely(completed != 0)) - req->req.status = -EIO; - else if (req->req.actual) { - /* these registers have zeroes in low bits; they miscount - * some (end-of-transfer) short packets: tx 14 as tx 12 - */ - if (ep->dma_fixup) - req->req.actual = min(req->req.actual + 3, - req->req.length); - - tmp = (req->req.length - req->req.actual); - completed = (tmp == 0); - if (completed && (ep->bEndpointAddress & USB_DIR_IN)) { - - /* maybe validate final short packet ... */ - if ((req->req.actual % ep->ep.maxpacket) != 0) - *ep->reg_udccs = UDCCS_BI_TSP/*|UDCCS_BI_TPC*/; - - /* ... or zlp, using pio fallback */ - else if (ep->bmAttributes == USB_ENDPOINT_XFER_BULK - && req->req.zero) { - DMSG("%s zlp terminate ...\n", ep->ep.name); - completed = 0; - } - } - } - - if (likely(completed)) { - done(ep, req, 0); - - /* maybe re-activate after completion */ - if (ep->stopped || list_empty(&ep->queue)) - goto done; - req = list_entry(ep->queue.next, struct pxa2xx_request, queue); - } - kick_dma(ep, req); -done: - local_irq_enable(); -} - -#endif - /*-------------------------------------------------------------------------*/ static int @@ -941,19 +698,8 @@ pxa2xx_ep_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags) (ep->desc->wMaxPacketSize))) return -EMSGSIZE; -#ifdef USE_DMA - // FIXME caller may already have done the dma mapping - if (ep->dma >= 0) { - _req->dma = dma_map_single(dev->dev, - _req->buf, _req->length, - ((ep->bEndpointAddress & USB_DIR_IN) != 0) - ? DMA_TO_DEVICE - : DMA_FROM_DEVICE); - } -#endif - DBG(DBG_NOISY, "%s queue req %p, len %d buf %p\n", - _ep->name, _req, _req->length, _req->buf); + _ep->name, _req, _req->length, _req->buf); local_irq_save(flags); @@ -1001,11 +747,6 @@ pxa2xx_ep_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags) local_irq_restore (flags); return -EL2HLT; } -#ifdef USE_DMA - /* either start dma or prime pio pump */ - } else if (ep->dma >= 0) { - kick_dma(ep, req); -#endif /* can the FIFO can satisfy the request immediately? */ } else if ((ep->bEndpointAddress & USB_DIR_IN) != 0) { if ((*ep->reg_udccs & UDCCS_BI_TFS) != 0 @@ -1016,7 +757,7 @@ pxa2xx_ep_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags) req = NULL; } - if (likely (req && ep->desc) && ep->dma < 0) + if (likely (req && ep->desc)) pio_irq_enable(ep->bEndpointAddress); } @@ -1037,10 +778,6 @@ static void nuke(struct pxa2xx_ep *ep, int status) struct pxa2xx_request *req; /* called with irqs blocked */ -#ifdef USE_DMA - if (ep->dma >= 0 && !ep->stopped) - cancel_dma(ep); -#endif while (!list_empty(&ep->queue)) { req = list_entry(ep->queue.next, struct pxa2xx_request, @@ -1075,19 +812,7 @@ static int pxa2xx_ep_dequeue(struct usb_ep *_ep, struct usb_request *_req) return -EINVAL; } -#ifdef USE_DMA - if (ep->dma >= 0 && ep->queue.next == &req->queue && !ep->stopped) { - cancel_dma(ep); - done(ep, req, -ECONNRESET); - /* restart i/o */ - if (!list_empty(&ep->queue)) { - req = list_entry(ep->queue.next, - struct pxa2xx_request, queue); - kick_dma(ep, req); - } - } else -#endif - done(ep, req, -ECONNRESET); + done(ep, req, -ECONNRESET); local_irq_restore(flags); return 0; @@ -1324,7 +1049,7 @@ udc_proc_read(char *page, char **start, off_t off, int count, /* basic device status */ t = scnprintf(next, size, DRIVER_DESC "\n" "%s version: %s\nGadget driver: %s\nHost %s\n\n", - driver_name, DRIVER_VERSION SIZE_STR DMASTR, + driver_name, DRIVER_VERSION SIZE_STR "(pio)", dev->driver ? dev->driver->driver.name : "(none)", is_vbus_present() ? "full speed" : "disconnected"); size -= t; @@ -1389,7 +1114,6 @@ udc_proc_read(char *page, char **start, off_t off, int count, for (i = 0; i < PXA_UDC_NUM_ENDPOINTS; i++) { struct pxa2xx_ep *ep = &dev->ep [i]; struct pxa2xx_request *req; - int t; if (i != 0) { const struct usb_endpoint_descriptor *d; @@ -1399,10 +1123,9 @@ udc_proc_read(char *page, char **start, off_t off, int count, continue; tmp = *dev->ep [i].reg_udccs; t = scnprintf(next, size, - "%s max %d %s udccs %02x irqs %lu/%lu\n", + "%s max %d %s udccs %02x irqs %lu\n", ep->ep.name, le16_to_cpu (d->wMaxPacketSize), - (ep->dma >= 0) ? "dma" : "pio", tmp, - ep->pio_irqs, ep->dma_irqs); + "pio", tmp, ep->pio_irqs); /* TODO translate all five groups of udccs bits! */ } else /* ep0 should only have one transfer queued */ @@ -1422,19 +1145,7 @@ udc_proc_read(char *page, char **start, off_t off, int count, continue; } list_for_each_entry(req, &ep->queue, queue) { -#ifdef USE_DMA - if (ep->dma >= 0 && req->queue.prev == &ep->queue) - t = scnprintf(next, size, - "\treq %p len %d/%d " - "buf %p (dma%d dcmd %08x)\n", - &req->req, req->req.actual, - req->req.length, req->req.buf, - ep->dma, DCMD(ep->dma) - // low 13 bits == bytes-to-go - ); - else -#endif - t = scnprintf(next, size, + t = scnprintf(next, size, "\treq %p len %d/%d buf %p\n", &req->req, req->req.actual, req->req.length, req->req.buf); @@ -1487,7 +1198,6 @@ static void udc_disable(struct pxa2xx_udc *dev) ep0_idle (dev); dev->gadget.speed = USB_SPEED_UNKNOWN; - LED_CONNECTED_OFF; } @@ -1513,7 +1223,7 @@ static void udc_reinit(struct pxa2xx_udc *dev) ep->desc = NULL; ep->stopped = 0; INIT_LIST_HEAD (&ep->queue); - ep->pio_irqs = ep->dma_irqs = 0; + ep->pio_irqs = 0; } /* the rest was statically initialized, and is read-only */ @@ -1665,7 +1375,6 @@ stop_activity(struct pxa2xx_udc *dev, struct usb_gadget_driver *driver) del_timer_sync(&dev->timer); /* report disconnect; the driver is already quiesced */ - LED_CONNECTED_OFF; if (driver) driver->disconnect(&dev->gadget); @@ -1714,16 +1423,13 @@ lubbock_vbus_irq(int irq, void *_dev) int vbus; dev->stats.irqs++; - HEX_DISPLAY(dev->stats.irqs); switch (irq) { case LUBBOCK_USB_IRQ: - LED_CONNECTED_ON; vbus = 1; disable_irq(LUBBOCK_USB_IRQ); enable_irq(LUBBOCK_USB_DISC_IRQ); break; case LUBBOCK_USB_DISC_IRQ: - LED_CONNECTED_OFF; vbus = 0; disable_irq(LUBBOCK_USB_DISC_IRQ); enable_irq(LUBBOCK_USB_IRQ); @@ -2039,18 +1745,6 @@ static void handle_ep(struct pxa2xx_ep *ep) /* fifos can hold packets, ready for reading... */ if (likely(req)) { -#ifdef USE_OUT_DMA -// TODO didn't yet debug out-dma. this approach assumes -// the worst about short packets and RPC; it might be better. - - if (likely(ep->dma >= 0)) { - if (!(udccs & UDCCS_BO_RSP)) { - *ep->reg_udccs = UDCCS_BO_RPC; - ep->dma_irqs++; - return; - } - } -#endif completed = read_fifo(ep, req); } else pio_irq_disable (ep->bEndpointAddress); @@ -2073,7 +1767,6 @@ pxa2xx_udc_irq(int irq, void *_dev) int handled; dev->stats.irqs++; - HEX_DISPLAY(dev->stats.irqs); do { u32 udccr = UDCCR; @@ -2124,7 +1817,6 @@ pxa2xx_udc_irq(int irq, void *_dev) } else { DBG(DBG_VERBOSE, "USB reset end\n"); dev->gadget.speed = USB_SPEED_FULL; - LED_CONNECTED_ON; memset(&dev->stats, 0, sizeof dev->stats); /* driver and endpoints are still reset */ } @@ -2216,7 +1908,6 @@ static struct pxa2xx_udc memory = { .bmAttributes = USB_ENDPOINT_XFER_BULK, .reg_udccs = &UDCCS1, .reg_uddr = &UDDR1, - drcmr (25) }, .ep[2] = { .ep = { @@ -2231,7 +1922,6 @@ static struct pxa2xx_udc memory = { .reg_udccs = &UDCCS2, .reg_ubcr = &UBCR2, .reg_uddr = &UDDR2, - drcmr (26) }, #ifndef CONFIG_USB_PXA2XX_SMALL .ep[3] = { @@ -2246,7 +1936,6 @@ static struct pxa2xx_udc memory = { .bmAttributes = USB_ENDPOINT_XFER_ISOC, .reg_udccs = &UDCCS3, .reg_uddr = &UDDR3, - drcmr (27) }, .ep[4] = { .ep = { @@ -2261,7 +1950,6 @@ static struct pxa2xx_udc memory = { .reg_udccs = &UDCCS4, .reg_ubcr = &UBCR4, .reg_uddr = &UDDR4, - drcmr (28) }, .ep[5] = { .ep = { @@ -2290,7 +1978,6 @@ static struct pxa2xx_udc memory = { .bmAttributes = USB_ENDPOINT_XFER_BULK, .reg_udccs = &UDCCS6, .reg_uddr = &UDDR6, - drcmr (30) }, .ep[7] = { .ep = { @@ -2305,7 +1992,6 @@ static struct pxa2xx_udc memory = { .reg_udccs = &UDCCS7, .reg_ubcr = &UBCR7, .reg_uddr = &UDDR7, - drcmr (31) }, .ep[8] = { .ep = { @@ -2319,7 +2005,6 @@ static struct pxa2xx_udc memory = { .bmAttributes = USB_ENDPOINT_XFER_ISOC, .reg_udccs = &UDCCS8, .reg_uddr = &UDDR8, - drcmr (32) }, .ep[9] = { .ep = { @@ -2334,7 +2019,6 @@ static struct pxa2xx_udc memory = { .reg_udccs = &UDCCS9, .reg_ubcr = &UBCR9, .reg_uddr = &UDDR9, - drcmr (33) }, .ep[10] = { .ep = { @@ -2363,7 +2047,6 @@ static struct pxa2xx_udc memory = { .bmAttributes = USB_ENDPOINT_XFER_BULK, .reg_udccs = &UDCCS11, .reg_uddr = &UDDR11, - drcmr (35) }, .ep[12] = { .ep = { @@ -2378,7 +2061,6 @@ static struct pxa2xx_udc memory = { .reg_udccs = &UDCCS12, .reg_ubcr = &UBCR12, .reg_uddr = &UDDR12, - drcmr (36) }, .ep[13] = { .ep = { @@ -2392,7 +2074,6 @@ static struct pxa2xx_udc memory = { .bmAttributes = USB_ENDPOINT_XFER_ISOC, .reg_udccs = &UDCCS13, .reg_uddr = &UDDR13, - drcmr (37) }, .ep[14] = { .ep = { @@ -2407,7 +2088,6 @@ static struct pxa2xx_udc memory = { .reg_udccs = &UDCCS14, .reg_ubcr = &UBCR14, .reg_uddr = &UDDR14, - drcmr (38) }, .ep[15] = { .ep = { @@ -2465,7 +2145,7 @@ static struct pxa2xx_udc memory = { static int __init pxa2xx_udc_probe(struct platform_device *pdev) { struct pxa2xx_udc *dev = &memory; - int retval, out_dma = 1, vbus_irq, irq; + int retval, vbus_irq, irq; u32 chiprev; /* insist on Intel/ARM/XScale */ @@ -2488,7 +2168,7 @@ static int __init pxa2xx_udc_probe(struct platform_device *pdev) case PXA250_B2: case PXA210_B2: case PXA250_B1: case PXA210_B1: case PXA250_B0: case PXA210_B0: - out_dma = 0; + /* OUT-DMA is broken ... */ /* fall through */ case PXA250_C0: case PXA210_C0: break; @@ -2497,11 +2177,9 @@ static int __init pxa2xx_udc_probe(struct platform_device *pdev) case IXP425_B0: case IXP465_AD: dev->has_cfr = 1; - out_dma = 0; break; #endif default: - out_dma = 0; printk(KERN_ERR "%s: unrecognized processor: %08x\n", driver_name, chiprev); /* iop3xx, ixp4xx, ... */ @@ -2512,25 +2190,11 @@ static int __init pxa2xx_udc_probe(struct platform_device *pdev) if (irq < 0) return -ENODEV; - pr_debug("%s: IRQ %d%s%s%s\n", driver_name, irq, + pr_debug("%s: IRQ %d%s%s\n", driver_name, irq, dev->has_cfr ? "" : " (!cfr)", - out_dma ? "" : " (broken dma-out)", - SIZE_STR DMASTR + SIZE_STR "(pio)" ); -#ifdef USE_DMA -#ifndef USE_OUT_DMA - out_dma = 0; -#endif - /* pxa 250 erratum 130 prevents using OUT dma (fixed C0) */ - if (!out_dma) { - DMSG("disabled OUT dma\n"); - dev->ep[ 2].reg_drcmr = dev->ep[ 4].reg_drcmr = 0; - dev->ep[ 7].reg_drcmr = dev->ep[ 9].reg_drcmr = 0; - dev->ep[12].reg_drcmr = dev->ep[14].reg_drcmr = 0; - } -#endif - /* other non-static parts of init */ dev->dev = &pdev->dev; dev->mach = pdev->dev.platform_data; @@ -2619,11 +2283,6 @@ lubbock_fail0: free_irq(LUBBOCK_USB_DISC_IRQ, dev); goto lubbock_fail0; } -#ifdef DEBUG - /* with U-Boot (but not BLOB), hex is off by default */ - HEX_DISPLAY(dev->stats.irqs); - LUB_DISC_BLNK_LED &= 0xff; -#endif } else #endif if (vbus_irq) { diff --git a/drivers/usb/gadget/pxa2xx_udc.h b/drivers/usb/gadget/pxa2xx_udc.h index 6b012e06af..0e5d0e6fb0 100644 --- a/drivers/usb/gadget/pxa2xx_udc.h +++ b/drivers/usb/gadget/pxa2xx_udc.h @@ -54,8 +54,6 @@ struct pxa2xx_ep { const struct usb_endpoint_descriptor *desc; struct list_head queue; unsigned long pio_irqs; - unsigned long dma_irqs; - short dma; unsigned short fifo_size; u8 bEndpointAddress; @@ -63,7 +61,7 @@ struct pxa2xx_ep { unsigned stopped : 1; unsigned dma_fixup : 1; - + /* UDCCS = UDC Control/Status for this EP * UBCR = UDC Byte Count Remaining (contents of OUT fifo) * UDDR = UDC Endpoint Data Register (the fifo) @@ -72,12 +70,6 @@ struct pxa2xx_ep { volatile u32 *reg_udccs; volatile u32 *reg_ubcr; volatile u32 *reg_uddr; -#ifdef USE_DMA - volatile u32 *reg_drcmr; -#define drcmr(n) .reg_drcmr = & DRCMR ## n , -#else -#define drcmr(n) -#endif }; struct pxa2xx_request { @@ -85,7 +77,7 @@ struct pxa2xx_request { struct list_head queue; }; -enum ep0_state { +enum ep0_state { EP0_IDLE, EP0_IN_DATA_PHASE, EP0_OUT_DATA_PHASE, @@ -108,7 +100,6 @@ struct udc_stats { #ifdef CONFIG_USB_PXA2XX_SMALL /* when memory's tight, SMALL config saves code+data. */ -#undef USE_DMA #define PXA_UDC_NUM_ENDPOINTS 3 #endif @@ -144,37 +135,8 @@ struct pxa2xx_udc { #ifdef CONFIG_ARCH_LUBBOCK #include /* lubbock can also report usb connect/disconnect irqs */ - -#ifdef DEBUG -#define HEX_DISPLAY(n) if (machine_is_lubbock()) { LUB_HEXLED = (n); } #endif -#endif - -/*-------------------------------------------------------------------------*/ - -/* LEDs are only for debug */ -#ifndef HEX_DISPLAY -#define HEX_DISPLAY(n) do {} while(0) -#endif - -#ifdef DEBUG -#include - -#define LED_CONNECTED_ON leds_event(led_green_on) -#define LED_CONNECTED_OFF do { \ - leds_event(led_green_off); \ - HEX_DISPLAY(0); \ - } while(0) -#endif - -#ifndef LED_CONNECTED_ON -#define LED_CONNECTED_ON do {} while(0) -#define LED_CONNECTED_OFF do {} while(0) -#endif - -/*-------------------------------------------------------------------------*/ - static struct pxa2xx_udc *the_controller; /*-------------------------------------------------------------------------*/ -- 2.39.5