From 931506d3b2208362efc678ee863ee42a90755e89 Mon Sep 17 00:00:00 2001 From: Anantha Subramanyam Date: Thu, 28 Feb 2008 15:58:35 -0800 Subject: [PATCH] sata_svw: Add support for HT1100 SATA controller This patch adds support (including ATAPI DMA) for HT1100 (aka BCM11000) SATA controller. Signed-off-by: Anantha Subramanyam Signed-off-by: Jeff Garzik --- drivers/ata/sata_svw.c | 77 ++++++++++++++++++++++++++++++++++-------- 1 file changed, 63 insertions(+), 14 deletions(-) diff --git a/drivers/ata/sata_svw.c b/drivers/ata/sata_svw.c index 69f651e0bc..840d1c4a78 100644 --- a/drivers/ata/sata_svw.c +++ b/drivers/ata/sata_svw.c @@ -45,6 +45,8 @@ #include #include #include +#include +#include #include #ifdef CONFIG_PPC_OF @@ -59,6 +61,7 @@ enum { /* ap->flags bits */ K2_FLAG_SATA_8_PORTS = (1 << 24), K2_FLAG_NO_ATAPI_DMA = (1 << 25), + K2_FLAG_BAR_POS_3 = (1 << 26), /* Taskfile registers offsets */ K2_SATA_TF_CMD_OFFSET = 0x00, @@ -88,8 +91,10 @@ enum { /* Port stride */ K2_SATA_PORT_OFFSET = 0x100, - board_svw4 = 0, - board_svw8 = 1, + chip_svw4 = 0, + chip_svw8 = 1, + chip_svw42 = 2, /* bar 3 */ + chip_svw43 = 3, /* bar 5 */ }; static u8 k2_stat_check_status(struct ata_port *ap); @@ -97,10 +102,25 @@ static u8 k2_stat_check_status(struct ata_port *ap); static int k2_sata_check_atapi_dma(struct ata_queued_cmd *qc) { + u8 cmnd = qc->scsicmd->cmnd[0]; + if (qc->ap->flags & K2_FLAG_NO_ATAPI_DMA) return -1; /* ATAPI DMA not supported */ + else { + switch (cmnd) { + case READ_10: + case READ_12: + case READ_16: + case WRITE_10: + case WRITE_12: + case WRITE_16: + return 0; + + default: + return -1; + } - return 0; + } } static int k2_sata_scr_read(struct ata_port *ap, unsigned int sc_reg, u32 *val) @@ -354,7 +374,7 @@ static const struct ata_port_operations k2_sata_ops = { }; static const struct ata_port_info k2_port_info[] = { - /* board_svw4 */ + /* chip_svw4 */ { .flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY | ATA_FLAG_MMIO | K2_FLAG_NO_ATAPI_DMA, @@ -363,7 +383,7 @@ static const struct ata_port_info k2_port_info[] = { .udma_mask = ATA_UDMA6, .port_ops = &k2_sata_ops, }, - /* board_svw8 */ + /* chip_svw8 */ { .flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY | ATA_FLAG_MMIO | K2_FLAG_NO_ATAPI_DMA | @@ -373,6 +393,24 @@ static const struct ata_port_info k2_port_info[] = { .udma_mask = ATA_UDMA6, .port_ops = &k2_sata_ops, }, + /* chip_svw42 */ + { + .flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY | + ATA_FLAG_MMIO | K2_FLAG_BAR_POS_3, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = ATA_UDMA6, + .port_ops = &k2_sata_ops, + }, + /* chip_svw43 */ + { + .flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY | + ATA_FLAG_MMIO, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = ATA_UDMA6, + .port_ops = &k2_sata_ops, + }, }; static void k2_sata_setup_port(struct ata_ioports *port, void __iomem *base) @@ -402,7 +440,7 @@ static int k2_sata_init_one(struct pci_dev *pdev, const struct pci_device_id *en { &k2_port_info[ent->driver_data], NULL }; struct ata_host *host; void __iomem *mmio_base; - int n_ports, i, rc; + int n_ports, i, rc, bar_pos; if (!printed_version++) dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n"); @@ -416,6 +454,9 @@ static int k2_sata_init_one(struct pci_dev *pdev, const struct pci_device_id *en if (!host) return -ENOMEM; + bar_pos = 5; + if (ppi[0]->flags & K2_FLAG_BAR_POS_3) + bar_pos = 3; /* * If this driver happens to only be useful on Apple's K2, then * we should check that here as it has a normal Serverworks ID @@ -428,17 +469,23 @@ static int k2_sata_init_one(struct pci_dev *pdev, const struct pci_device_id *en * Check if we have resources mapped at all (second function may * have been disabled by firmware) */ - if (pci_resource_len(pdev, 5) == 0) + if (pci_resource_len(pdev, bar_pos) == 0) { + /* In IDE mode we need to pin the device to ensure that + pcim_release does not clear the busmaster bit in config + space, clearing causes busmaster DMA to fail on + ports 3 & 4 */ + pcim_pin_device(pdev); return -ENODEV; + } /* Request and iomap PCI regions */ - rc = pcim_iomap_regions(pdev, 1 << 5, DRV_NAME); + rc = pcim_iomap_regions(pdev, 1 << bar_pos, DRV_NAME); if (rc == -EBUSY) pcim_pin_device(pdev); if (rc) return rc; host->iomap = pcim_iomap_table(pdev); - mmio_base = host->iomap[5]; + mmio_base = host->iomap[bar_pos]; /* different controllers have different number of ports - currently 4 or 8 */ /* All ports are on the same function. Multi-function device is no @@ -483,11 +530,13 @@ static int k2_sata_init_one(struct pci_dev *pdev, const struct pci_device_id *en * controller * */ static const struct pci_device_id k2_sata_pci_tbl[] = { - { PCI_VDEVICE(SERVERWORKS, 0x0240), board_svw4 }, - { PCI_VDEVICE(SERVERWORKS, 0x0241), board_svw4 }, - { PCI_VDEVICE(SERVERWORKS, 0x0242), board_svw8 }, - { PCI_VDEVICE(SERVERWORKS, 0x024a), board_svw4 }, - { PCI_VDEVICE(SERVERWORKS, 0x024b), board_svw4 }, + { PCI_VDEVICE(SERVERWORKS, 0x0240), chip_svw4 }, + { PCI_VDEVICE(SERVERWORKS, 0x0241), chip_svw4 }, + { PCI_VDEVICE(SERVERWORKS, 0x0242), chip_svw8 }, + { PCI_VDEVICE(SERVERWORKS, 0x024a), chip_svw4 }, + { PCI_VDEVICE(SERVERWORKS, 0x024b), chip_svw4 }, + { PCI_VDEVICE(SERVERWORKS, 0x0410), chip_svw42 }, + { PCI_VDEVICE(SERVERWORKS, 0x0411), chip_svw43 }, { } }; -- 2.39.5