From 8ac98ce17cf318f6ceb1eb88053917001f5ca60a Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Tue, 27 Nov 2007 21:35:53 +0100 Subject: [PATCH] siimage: remove resetproc() method The intent behind siimage_reset() was probably to hard reset the interface and the SATA PHY but as the code writes to two reserved bits instead, it obviously has been ineffective from the start. So, just remove it. Signed-off-by: Sergei Shtylyov Cc: Alan Cox Signed-off-by: Bartlomiej Zolnierkiewicz --- drivers/ide/pci/siimage.c | 45 +-------------------------------------- 1 file changed, 1 insertion(+), 44 deletions(-) diff --git a/drivers/ide/pci/siimage.c b/drivers/ide/pci/siimage.c index 6d99441c60..5709c25254 100644 --- a/drivers/ide/pci/siimage.c +++ b/drivers/ide/pci/siimage.c @@ -1,5 +1,5 @@ /* - * linux/drivers/ide/pci/siimage.c Version 1.18 Oct 18 2007 + * linux/drivers/ide/pci/siimage.c Version 1.19 Nov 16 2007 * * Copyright (C) 2001-2002 Andre Hedrick * Copyright (C) 2003 Red Hat @@ -459,48 +459,6 @@ static void sil_sata_pre_reset(ide_drive_t *drive) } } -/** - * siimage_reset - reset a device on an siimage controller - * @drive: drive to reset - * - * Perform a controller level reset fo the device. For - * SATA we must also check the PHY. - */ - -static void siimage_reset (ide_drive_t *drive) -{ - ide_hwif_t *hwif = HWIF(drive); - u8 reset = 0; - unsigned long addr = siimage_selreg(hwif, 0); - - if (hwif->mmio) { - reset = hwif->INB(addr); - hwif->OUTB((reset|0x03), addr); - /* FIXME:posting */ - udelay(25); - hwif->OUTB(reset, addr); - (void) hwif->INB(addr); - } else { - pci_read_config_byte(hwif->pci_dev, addr, &reset); - pci_write_config_byte(hwif->pci_dev, addr, reset|0x03); - udelay(25); - pci_write_config_byte(hwif->pci_dev, addr, reset); - pci_read_config_byte(hwif->pci_dev, addr, &reset); - } - - if (SATA_STATUS_REG) { - /* SATA_STATUS_REG is valid only when in MMIO mode */ - u32 sata_stat = readl((void __iomem *)SATA_STATUS_REG); - printk(KERN_WARNING "%s: reset phy, status=0x%08x, %s\n", - hwif->name, sata_stat, __FUNCTION__); - if (!(sata_stat)) { - printk(KERN_WARNING "%s: reset phy dead, status=0x%08x\n", - hwif->name, sata_stat); - drive->failures++; - } - } -} - /** * proc_reports_siimage - add siimage controller to proc * @dev: PCI device @@ -857,7 +815,6 @@ static void __devinit init_hwif_siimage(ide_hwif_t *hwif) { u8 sata = is_sata(hwif); - hwif->resetproc = &siimage_reset; hwif->set_pio_mode = &sil_set_pio_mode; hwif->set_dma_mode = &sil_set_dma_mode; -- 2.39.5