From 85afb934575abdff1b2ac8ea4d522d1355f22a89 Mon Sep 17 00:00:00 2001 From: Mark Lord Date: Sat, 19 Apr 2008 14:54:41 -0400 Subject: [PATCH] sata_mv: re-enable hotplug, update TODO list Re-enable hotplug, now that the interrupt/error handling are mostly sane. Also update the TODO list at the top. Signed-off-by: Mark Lord Signed-off-by: Jeff Garzik --- drivers/ata/sata_mv.c | 79 ++++++++++++++++--------------------------- 1 file changed, 29 insertions(+), 50 deletions(-) diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c index 4fa54805eb..26a6337195 100644 --- a/drivers/ata/sata_mv.c +++ b/drivers/ata/sata_mv.c @@ -23,46 +23,34 @@ */ /* - sata_mv TODO list: - - 1) Needs a full errata audit for all chipsets. I implemented most - of the errata workarounds found in the Marvell vendor driver, but - I distinctly remember a couple workarounds (one related to PCI-X) - are still needed. - - 2) Improve/fix IRQ and error handling sequences. - - 3) ATAPI support (Marvell claims the 60xx/70xx chips can do it). - - 4) Think about TCQ support here, and for libata in general - with controllers that suppport it via host-queuing hardware - (a software-only implementation could be a nightmare). - - 5) Investigate problems with PCI Message Signalled Interrupts (MSI). - - 6) Cache frequently-accessed registers in mv_port_priv to reduce overhead. - - 7) Fix/reenable hot plug/unplug (should happen as a side-effect of (2) above). - - 8) Develop a low-power-consumption strategy, and implement it. - - 9) [Experiment, low priority] See if ATAPI can be supported using - "unknown FIS" or "vendor-specific FIS" support, or something creative - like that. - - 10) [Experiment, low priority] Investigate interrupt coalescing. - Quite often, especially with PCI Message Signalled Interrupts (MSI), - the overhead reduced by interrupt mitigation is quite often not - worth the latency cost. - - 11) [Experiment, Marvell value added] Is it possible to use target - mode to cross-connect two Linux boxes with Marvell cards? If so, - creating LibATA target mode support would be very interesting. - - Target mode, for those without docs, is the ability to directly - connect two SATA controllers. - -*/ + * sata_mv TODO list: + * + * --> Errata workaround for NCQ device errors. + * + * --> More errata workarounds for PCI-X. + * + * --> Complete a full errata audit for all chipsets to identify others. + * + * --> ATAPI support (Marvell claims the 60xx/70xx chips can do it). + * + * --> Investigate problems with PCI Message Signalled Interrupts (MSI). + * + * --> Cache frequently-accessed registers in mv_port_priv to reduce overhead. + * + * --> Develop a low-power-consumption strategy, and implement it. + * + * --> [Experiment, low priority] Investigate interrupt coalescing. + * Quite often, especially with PCI Message Signalled Interrupts (MSI), + * the overhead reduced by interrupt mitigation is quite often not + * worth the latency cost. + * + * --> [Experiment, Marvell value added] Is it possible to use target + * mode to cross-connect two Linux boxes with Marvell cards? If so, + * creating LibATA target mode support would be very interesting. + * + * Target mode, for those without docs, is the ability to directly + * connect two SATA ports. + */ #include #include @@ -300,9 +288,7 @@ enum { EDMA_ERR_IRQ_TRANSIENT = EDMA_ERR_LNK_CTRL_RX_0 | EDMA_ERR_LNK_CTRL_RX_1 | EDMA_ERR_LNK_CTRL_RX_3 | - EDMA_ERR_LNK_CTRL_TX | - /* temporary, until we fix hotplug: */ - (EDMA_ERR_DEV_DCON | EDMA_ERR_DEV_CON), + EDMA_ERR_LNK_CTRL_TX, EDMA_EH_FREEZE = EDMA_ERR_D_PAR | EDMA_ERR_PRD_PAR | @@ -2124,13 +2110,6 @@ static int mv6_reset_hc(struct mv_host_priv *hpriv, void __iomem *mmio, printk(KERN_ERR DRV_NAME ": can't clear global reset\n"); rc = 1; } - /* - * Temporary: wait 3 seconds before port-probing can happen, - * so that we don't miss finding sleepy SilXXXX port-multipliers. - * This can go away once hotplug is fully/correctly implemented. - */ - if (rc == 0) - msleep(3000); done: return rc; } -- 2.39.5