From 80a65fc5ee04497e6c28bdaefc44d375b19c4a79 Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Sun, 15 Jun 2008 21:00:22 +0200 Subject: [PATCH] opti621: add PIO 4 support * Add PIO 4 support. While at it: * Use a single struct ide_port_info instance for OPTi621 and OPTi621X. Based on a bugreport from Juergen Kosel & inspired by pata_opti.c code. Tested-by: Juergen Kosel Signed-off-by: Bartlomiej Zolnierkiewicz --- drivers/ide/pci/opti621.c | 46 ++++++++++++--------------------------- 1 file changed, 14 insertions(+), 32 deletions(-) diff --git a/drivers/ide/pci/opti621.c b/drivers/ide/pci/opti621.c index 8c715b7a85..725c80508d 100644 --- a/drivers/ide/pci/opti621.c +++ b/drivers/ide/pci/opti621.c @@ -90,16 +90,6 @@ #include -//#define OPTI621_MAX_PIO 3 -/* In fact, I do not have any PIO 4 drive - * (address: 25 ns, data: 70 ns, recovery: 35 ns), - * but OPTi 82C621 is programmable and it can do (minimal values): - * on 40MHz PCI bus (pulse 25 ns): - * address: 25 ns, data: 25 ns, recovery: 50 ns; - * on 20MHz PCI bus (pulse 50 ns): - * address: 50 ns, data: 50 ns, recovery: 100 ns. - */ - #define READ_REG 0 /* index of Read cycle timing register */ #define WRITE_REG 1 /* index of Write cycle timing register */ #define CNTRL_REG 3 /* index of Control register */ @@ -150,13 +140,13 @@ static void opti621_set_pio_mode(ide_drive_t *drive, const u8 pio) u8 tim, misc, addr_pio = pio, clk; /* DRDY is default 2 (by OPTi Databook) */ - static const u8 addr_timings[2][4] = { - { 0x20, 0x10, 0x00, 0x00 }, /* 33 MHz */ - { 0x10, 0x10, 0x00, 0x00 }, /* 25 MHz */ + static const u8 addr_timings[2][5] = { + { 0x20, 0x10, 0x00, 0x00, 0x00 }, /* 33 MHz */ + { 0x10, 0x10, 0x00, 0x00, 0x00 }, /* 25 MHz */ }; - static const u8 data_rec_timings[2][4] = { - { 0x5b, 0x45, 0x32, 0x21 }, /* 33 MHz */ - { 0x48, 0x34, 0x21, 0x10 } /* 25 MHz */ + static const u8 data_rec_timings[2][5] = { + { 0x5b, 0x45, 0x32, 0x21, 0x20 }, /* 33 MHz */ + { 0x48, 0x34, 0x21, 0x10, 0x10 } /* 25 MHz */ }; drive->drive_data = XFER_PIO_0 + pio; @@ -209,30 +199,22 @@ static const struct ide_port_ops opti621_port_ops = { .set_pio_mode = opti621_set_pio_mode, }; -static const struct ide_port_info opti621_chipsets[] __devinitdata = { - { /* 0 */ - .name = "OPTI621", - .enablebits = { {0x45, 0x80, 0x00}, {0x40, 0x08, 0x00} }, - .port_ops = &opti621_port_ops, - .host_flags = IDE_HFLAG_NO_DMA, - .pio_mask = ATA_PIO3, - }, { /* 1 */ - .name = "OPTI621X", - .enablebits = { {0x45, 0x80, 0x00}, {0x40, 0x08, 0x00} }, - .port_ops = &opti621_port_ops, - .host_flags = IDE_HFLAG_NO_DMA, - .pio_mask = ATA_PIO3, - } +static const struct ide_port_info opti621_chipset __devinitdata = { + .name = "OPTI621/X", + .enablebits = { {0x45, 0x80, 0x00}, {0x40, 0x08, 0x00} }, + .port_ops = &opti621_port_ops, + .host_flags = IDE_HFLAG_NO_DMA, + .pio_mask = ATA_PIO4, }; static int __devinit opti621_init_one(struct pci_dev *dev, const struct pci_device_id *id) { - return ide_setup_pci_device(dev, &opti621_chipsets[id->driver_data]); + return ide_setup_pci_device(dev, &opti621_chipset); } static const struct pci_device_id opti621_pci_tbl[] = { { PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C621), 0 }, - { PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C825), 1 }, + { PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C825), 0 }, { 0, }, }; MODULE_DEVICE_TABLE(pci, opti621_pci_tbl); -- 2.39.5