From 77280989673ee1ef736a92617f52e2be45651833 Mon Sep 17 00:00:00 2001 From: Tejun Heo Date: Fri, 2 Feb 2007 14:51:09 +0900 Subject: [PATCH] ahci/pata_jmicron: fix JMicron quirk For all JMicrons except for 361 and 368, AHCI mode enable bits in the Control(1) should be set. This used to be done in both ahci and pata_jmicron but while moving programming to PCI quirk, it was removed from ahci part while still left in pata_jmicron. The implemented JMicron PCI quirk was incorrect in that it didn't program AHCI mode enable bits. If pata_jmicron is loaded first and programs those bits, the ahci ports work; otherwise, ahci device detection fails miserably. This patch makes JMicron PCI quirk clear SATA IDE mode bits and set AHCI mode bits and remove the respective part from pata_jmicron. Tested on JMB361, 363 and 368. Signed-off-by: Tejun Heo Signed-off-by: Jeff Garzik --- drivers/ata/pata_jmicron.c | 18 +++++------------- drivers/pci/quirks.c | 4 ++-- 2 files changed, 7 insertions(+), 15 deletions(-) diff --git a/drivers/ata/pata_jmicron.c b/drivers/ata/pata_jmicron.c index 2d661cb4df..d50264af28 100644 --- a/drivers/ata/pata_jmicron.c +++ b/drivers/ata/pata_jmicron.c @@ -204,20 +204,12 @@ static int jmicron_init_one (struct pci_dev *pdev, const struct pci_device_id *i u32 reg; - if (id->driver_data != 368) { - /* Put the controller into AHCI mode in case the AHCI driver - has not yet been loaded. This can be done with either - function present */ + /* PATA controller is fn 1, AHCI is fn 0 */ + if (id->driver_data != 368 && PCI_FUNC(pdev->devfn) != 1) + return -ENODEV; - /* FIXME: We may want a way to override this in future */ - pci_write_config_byte(pdev, 0x41, 0xa1); - - /* PATA controller is fn 1, AHCI is fn 0 */ - if (PCI_FUNC(pdev->devfn) != 1) - return -ENODEV; - } - if ( id->driver_data == 365 || id->driver_data == 366) { - /* The 365/66 have two PATA channels, redirect the second */ + /* The 365/66 have two PATA channels, redirect the second */ + if (id->driver_data == 365 || id->driver_data == 366) { pci_read_config_dword(pdev, 0x80, ®); reg |= (1 << 24); /* IDE1 to PATA IDE secondary */ pci_write_config_dword(pdev, 0x80, reg); diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c index dcc0c1ab95..c913ea4e54 100644 --- a/drivers/pci/quirks.c +++ b/drivers/pci/quirks.c @@ -1262,8 +1262,8 @@ static void quirk_jmicron_dualfn(struct pci_dev *pdev) pci_read_config_dword(pdev, 0x40, &conf); /* Enable dual function mode, AHCI on fn 0, IDE fn1 */ /* Set the class codes correctly and then direct IDE 0 */ - conf &= ~0x000F0200; /* Clear bit 9 and 16-19 */ - conf |= 0x00C20002; /* Set bit 1, 17, 22, 23 */ + conf &= ~0x000FF200; /* Clear bit 9 and 12-19 */ + conf |= 0x00C2A102; /* Set 1, 8, 13, 15, 17, 22, 23 */ pci_write_config_dword(pdev, 0x40, conf); /* Reconfigure so that the PCI scanner discovers the -- 2.39.5