From 549edb83327f2a5027a22d65b10603b01dc40175 Mon Sep 17 00:00:00 2001 From: Juerg Haefliger Date: Wed, 6 Aug 2008 22:41:03 +0200 Subject: [PATCH] hwmon: (dme1737) Add support for the SMSC SCH5027 Add support for the SCH5027. The differences to the DME1737 are: - No support for programmable temp offsets - In auto mode, PWM outputs stay on min value if temp goes below low threshold and can't be programmed to fully turn off - Different voltage scaling - No VID input Signed-off-by: Juerg Haefliger Signed-off-by: Jean Delvare --- Documentation/hwmon/dme1737 | 53 +++++++--- drivers/hwmon/Kconfig | 4 +- drivers/hwmon/dme1737.c | 193 ++++++++++++++++++++++++------------ 3 files changed, 169 insertions(+), 81 deletions(-) diff --git a/Documentation/hwmon/dme1737 b/Documentation/hwmon/dme1737 index b1fe009994..001d2e70bc 100644 --- a/Documentation/hwmon/dme1737 +++ b/Documentation/hwmon/dme1737 @@ -10,6 +10,10 @@ Supported chips: Prefix: 'sch311x' Addresses scanned: none, address read from Super-I/O config space Datasheet: http://www.nuhorizons.com/FeaturedProducts/Volume1/SMSC/311x.pdf + * SMSC SCH5027 + Prefix: 'sch5027' + Addresses scanned: I2C 0x2c, 0x2d, 0x2e + Datasheet: Provided by SMSC upon request and under NDA Authors: Juerg Haefliger @@ -27,33 +31,31 @@ Module Parameters following boards: - VIA EPIA SN18000 -Note that there is no need to use this parameter if the driver loads without -complaining. The driver will say so if it is necessary. - Description ----------- This driver implements support for the hardware monitoring capabilities of the -SMSC DME1737 and Asus A8000 (which are the same) and SMSC SCH311x Super-I/O -chips. These chips feature monitoring of 3 temp sensors temp[1-3] (2 remote -diodes and 1 internal), 7 voltages in[0-6] (6 external and 1 internal) and up -to 6 fan speeds fan[1-6]. Additionally, the chips implement up to 5 PWM -outputs pwm[1-3,5-6] for controlling fan speeds both manually and +SMSC DME1737 and Asus A8000 (which are the same), SMSC SCH5027, and SMSC +SCH311x Super-I/O chips. These chips feature monitoring of 3 temp sensors +temp[1-3] (2 remote diodes and 1 internal), 7 voltages in[0-6] (6 external and +1 internal) and up to 6 fan speeds fan[1-6]. Additionally, the chips implement +up to 5 PWM outputs pwm[1-3,5-6] for controlling fan speeds both manually and automatically. -For the DME1737 and A8000, fan[1-2] and pwm[1-2] are always present. Fan[3-6] -and pwm[3,5-6] are optional features and their availability depends on the -configuration of the chip. The driver will detect which features are present -during initialization and create the sysfs attributes accordingly. +For the DME1737, A8000 and SCH5027, fan[1-2] and pwm[1-2] are always present. +Fan[3-6] and pwm[3,5-6] are optional features and their availability depends on +the configuration of the chip. The driver will detect which features are +present during initialization and create the sysfs attributes accordingly. For the SCH311x, fan[1-3] and pwm[1-3] are always present and fan[4-6] and pwm[5-6] don't exist. -The hardware monitoring features of the DME1737 and A8000 are only accessible -via SMBus, while the SCH311x only provides access via the ISA bus. The driver -will therefore register itself as an I2C client driver if it detects a DME1737 -or A8000 and as a platform driver if it detects a SCH311x chip. +The hardware monitoring features of the DME1737, A8000, and SCH5027 are only +accessible via SMBus, while the SCH311x only provides access via the ISA bus. +The driver will therefore register itself as an I2C client driver if it detects +a DME1737, A8000, or SCH5027 and as a platform driver if it detects a SCH311x +chip. Voltage Monitoring @@ -64,6 +66,7 @@ scaling resistors. The values returned by the driver therefore reflect true millivolts and don't need scaling. The voltage inputs are mapped as follows (the last column indicates the input ranges): +DME1737, A8000: in0: +5VTR (+5V standby) 0V - 6.64V in1: Vccp (processor core) 0V - 3V in2: VCC (internal +3.3V) 0V - 4.38V @@ -72,6 +75,24 @@ millivolts and don't need scaling. The voltage inputs are mapped as follows in5: VTR (+3.3V standby) 0V - 4.38V in6: Vbat (+3.0V) 0V - 4.38V +SCH311x: + in0: +2.5V 0V - 6.64V + in1: Vccp (processor core) 0V - 2V + in2: VCC (internal +3.3V) 0V - 4.38V + in3: +5V 0V - 6.64V + in4: +12V 0V - 16V + in5: VTR (+3.3V standby) 0V - 4.38V + in6: Vbat (+3.0V) 0V - 4.38V + +SCH5027: + in0: +5VTR (+5V standby) 0V - 6.64V + in1: Vccp (processor core) 0V - 3V + in2: VCC (internal +3.3V) 0V - 4.38V + in3: V2_IN 0V - 1.5V + in4: V1_IN 0V - 1.5V + in5: VTR (+3.3V standby) 0V - 4.38V + in6: Vbat (+3.0V) 0V - 4.38V + Each voltage input has associated min and max limits which trigger an alarm when crossed. diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig index c882fd05cf..1de240a26f 100644 --- a/drivers/hwmon/Kconfig +++ b/drivers/hwmon/Kconfig @@ -575,8 +575,8 @@ config SENSORS_DME1737 select HWMON_VID help If you say yes here you get support for the hardware monitoring - and fan control features of the SMSC DME1737 (and compatibles - like the Asus A8000) and SCH311x Super-I/O chips. + and fan control features of the SMSC DME1737, SCH311x, SCH5027, and + Asus A8000 Super-I/O chips. This driver can also be built as a module. If so, the module will be called dme1737. diff --git a/drivers/hwmon/dme1737.c b/drivers/hwmon/dme1737.c index b36290048b..cdb8311e4e 100644 --- a/drivers/hwmon/dme1737.c +++ b/drivers/hwmon/dme1737.c @@ -1,11 +1,11 @@ /* - * dme1737.c - Driver for the SMSC DME1737, Asus A8000, and SMSC SCH311x - * Super-I/O chips integrated hardware monitoring features. - * Copyright (c) 2007 Juerg Haefliger + * dme1737.c - Driver for the SMSC DME1737, Asus A8000, SMSC SCH311x and + * SCH5027 Super-I/O chips integrated hardware monitoring features. + * Copyright (c) 2007, 2008 Juerg Haefliger * * This driver is an I2C/ISA hybrid, meaning that it uses the I2C bus to access - * the chip registers if a DME1737 (or A8000) is found and the ISA bus if a - * SCH311x chip is found. Both types of chips have very similar hardware + * the chip registers if a DME1737, A8000, or SCH5027 is found and the ISA bus + * if a SCH311x chip is found. Both types of chips have very similar hardware * monitoring capabilities but differ in the way they can be accessed. * * This program is free software; you can redistribute it and/or modify @@ -57,7 +57,10 @@ MODULE_PARM_DESC(probe_all_addr, "Include probing of non-standard LPC " static const unsigned short normal_i2c[] = {0x2c, 0x2d, 0x2e, I2C_CLIENT_END}; /* Insmod parameters */ -I2C_CLIENT_INSMOD_1(dme1737); +I2C_CLIENT_INSMOD_2(dme1737, sch5027); + +/* ISA chip types */ +enum isa_chips { sch311x = sch5027 + 1 }; /* --------------------------------------------------------------------- * Registers @@ -163,6 +166,7 @@ static const u8 DME1737_BIT_ALARM_FAN[] = {10, 11, 12, 13, 22, 23}; #define DME1737_VERSTEP 0x88 #define DME1737_VERSTEP_MASK 0xf8 #define SCH311X_DEVICE 0x8c +#define SCH5027_VERSTEP 0x69 /* Length of ISA address segment */ #define DME1737_EXTENT 2 @@ -182,6 +186,7 @@ struct dme1737_data { unsigned long last_update; /* in jiffies */ unsigned long last_vbat; /* in jiffies */ enum chips type; + const int *in_nominal; /* pointer to IN_NOMINAL array */ u8 vid; u8 pwm_rr_en; @@ -220,23 +225,23 @@ static const int IN_NOMINAL_DME1737[] = {5000, 2250, 3300, 5000, 12000, 3300, 3300}; static const int IN_NOMINAL_SCH311x[] = {2500, 1500, 3300, 5000, 12000, 3300, 3300}; -#define IN_NOMINAL(ix, type) (((type) == dme1737) ? \ - IN_NOMINAL_DME1737[(ix)] : \ - IN_NOMINAL_SCH311x[(ix)]) +static const int IN_NOMINAL_SCH5027[] = {5000, 2250, 3300, 1125, 1125, 3300, + 3300}; +#define IN_NOMINAL(type) ((type) == sch311x ? IN_NOMINAL_SCH311x : \ + (type) == sch5027 ? IN_NOMINAL_SCH5027 : \ + IN_NOMINAL_DME1737) /* Voltage input * Voltage inputs have 16 bits resolution, limit values have 8 bits * resolution. */ -static inline int IN_FROM_REG(int reg, int ix, int res, int type) +static inline int IN_FROM_REG(int reg, int nominal, int res) { - return (reg * IN_NOMINAL(ix, type) + (3 << (res - 3))) / - (3 << (res - 2)); + return (reg * nominal + (3 << (res - 3))) / (3 << (res - 2)); } -static inline int IN_TO_REG(int val, int ix, int type) +static inline int IN_TO_REG(int val, int nominal) { - return SENSORS_LIMIT((val * 192 + IN_NOMINAL(ix, type) / 2) / - IN_NOMINAL(ix, type), 0, 255); + return SENSORS_LIMIT((val * 192 + nominal / 2) / nominal, 0, 255); } /* Temperature input @@ -565,7 +570,10 @@ static struct dme1737_data *dme1737_update_device(struct device *dev) /* Sample register contents every 1 sec */ if (time_after(jiffies, data->last_update + HZ) || !data->valid) { - data->vid = dme1737_read(client, DME1737_REG_VID) & 0x3f; + if (data->type != sch5027) { + data->vid = dme1737_read(client, DME1737_REG_VID) & + 0x3f; + } /* In (voltage) registers */ for (ix = 0; ix < ARRAY_SIZE(data->in); ix++) { @@ -593,8 +601,10 @@ static struct dme1737_data *dme1737_update_device(struct device *dev) DME1737_REG_TEMP_MIN(ix)); data->temp_max[ix] = dme1737_read(client, DME1737_REG_TEMP_MAX(ix)); - data->temp_offset[ix] = dme1737_read(client, - DME1737_REG_TEMP_OFFSET(ix)); + if (data->type != sch5027) { + data->temp_offset[ix] = dme1737_read(client, + DME1737_REG_TEMP_OFFSET(ix)); + } } /* In and temp LSB registers @@ -669,9 +679,11 @@ static struct dme1737_data *dme1737_update_device(struct device *dev) data->zone_abs[ix] = dme1737_read(client, DME1737_REG_ZONE_ABS(ix)); } - for (ix = 0; ix < ARRAY_SIZE(data->zone_hyst); ix++) { - data->zone_hyst[ix] = dme1737_read(client, + if (data->type != sch5027) { + for (ix = 0; ix < ARRAY_SIZE(data->zone_hyst); ix++) { + data->zone_hyst[ix] = dme1737_read(client, DME1737_REG_ZONE_HYST(ix)); + } } /* Alarm registers */ @@ -735,13 +747,13 @@ static ssize_t show_in(struct device *dev, struct device_attribute *attr, switch (fn) { case SYS_IN_INPUT: - res = IN_FROM_REG(data->in[ix], ix, 16, data->type); + res = IN_FROM_REG(data->in[ix], data->in_nominal[ix], 16); break; case SYS_IN_MIN: - res = IN_FROM_REG(data->in_min[ix], ix, 8, data->type); + res = IN_FROM_REG(data->in_min[ix], data->in_nominal[ix], 8); break; case SYS_IN_MAX: - res = IN_FROM_REG(data->in_max[ix], ix, 8, data->type); + res = IN_FROM_REG(data->in_max[ix], data->in_nominal[ix], 8); break; case SYS_IN_ALARM: res = (data->alarms >> DME1737_BIT_ALARM_IN[ix]) & 0x01; @@ -768,12 +780,12 @@ static ssize_t set_in(struct device *dev, struct device_attribute *attr, mutex_lock(&data->update_lock); switch (fn) { case SYS_IN_MIN: - data->in_min[ix] = IN_TO_REG(val, ix, data->type); + data->in_min[ix] = IN_TO_REG(val, data->in_nominal[ix]); dme1737_write(client, DME1737_REG_IN_MIN(ix), data->in_min[ix]); break; case SYS_IN_MAX: - data->in_max[ix] = IN_TO_REG(val, ix, data->type); + data->in_max[ix] = IN_TO_REG(val, data->in_nominal[ix]); dme1737_write(client, DME1737_REG_IN_MAX(ix), data->in_max[ix]); break; @@ -1570,43 +1582,56 @@ static struct attribute *dme1737_attr[] ={ &sensor_dev_attr_temp1_max.dev_attr.attr, &sensor_dev_attr_temp1_alarm.dev_attr.attr, &sensor_dev_attr_temp1_fault.dev_attr.attr, - &sensor_dev_attr_temp1_offset.dev_attr.attr, &sensor_dev_attr_temp2_input.dev_attr.attr, &sensor_dev_attr_temp2_min.dev_attr.attr, &sensor_dev_attr_temp2_max.dev_attr.attr, &sensor_dev_attr_temp2_alarm.dev_attr.attr, &sensor_dev_attr_temp2_fault.dev_attr.attr, - &sensor_dev_attr_temp2_offset.dev_attr.attr, &sensor_dev_attr_temp3_input.dev_attr.attr, &sensor_dev_attr_temp3_min.dev_attr.attr, &sensor_dev_attr_temp3_max.dev_attr.attr, &sensor_dev_attr_temp3_alarm.dev_attr.attr, &sensor_dev_attr_temp3_fault.dev_attr.attr, - &sensor_dev_attr_temp3_offset.dev_attr.attr, /* Zones */ - &sensor_dev_attr_zone1_auto_point1_temp_hyst.dev_attr.attr, &sensor_dev_attr_zone1_auto_point1_temp.dev_attr.attr, &sensor_dev_attr_zone1_auto_point2_temp.dev_attr.attr, &sensor_dev_attr_zone1_auto_point3_temp.dev_attr.attr, &sensor_dev_attr_zone1_auto_channels_temp.dev_attr.attr, - &sensor_dev_attr_zone2_auto_point1_temp_hyst.dev_attr.attr, &sensor_dev_attr_zone2_auto_point1_temp.dev_attr.attr, &sensor_dev_attr_zone2_auto_point2_temp.dev_attr.attr, &sensor_dev_attr_zone2_auto_point3_temp.dev_attr.attr, &sensor_dev_attr_zone2_auto_channels_temp.dev_attr.attr, - &sensor_dev_attr_zone3_auto_point1_temp_hyst.dev_attr.attr, &sensor_dev_attr_zone3_auto_point1_temp.dev_attr.attr, &sensor_dev_attr_zone3_auto_point2_temp.dev_attr.attr, &sensor_dev_attr_zone3_auto_point3_temp.dev_attr.attr, &sensor_dev_attr_zone3_auto_channels_temp.dev_attr.attr, + NULL +}; + +static const struct attribute_group dme1737_group = { + .attrs = dme1737_attr, +}; + +/* The following struct holds misc attributes, which are not available in all + * chips. Their creation depends on the chip type which is determined during + * module load. */ +static struct attribute *dme1737_misc_attr[] = { + /* Temperatures */ + &sensor_dev_attr_temp1_offset.dev_attr.attr, + &sensor_dev_attr_temp2_offset.dev_attr.attr, + &sensor_dev_attr_temp3_offset.dev_attr.attr, + /* Zones */ + &sensor_dev_attr_zone1_auto_point1_temp_hyst.dev_attr.attr, + &sensor_dev_attr_zone2_auto_point1_temp_hyst.dev_attr.attr, + &sensor_dev_attr_zone3_auto_point1_temp_hyst.dev_attr.attr, /* Misc */ &dev_attr_vrm.attr, &dev_attr_cpu0_vid.attr, NULL }; -static const struct attribute_group dme1737_group = { - .attrs = dme1737_attr, +static const struct attribute_group dme1737_misc_group = { + .attrs = dme1737_misc_attr, }; /* The following structs hold the PWM attributes, some of which are optional. @@ -1618,7 +1643,6 @@ static struct attribute *dme1737_pwm1_attr[] = { &sensor_dev_attr_pwm1_enable.dev_attr.attr, &sensor_dev_attr_pwm1_ramp_rate.dev_attr.attr, &sensor_dev_attr_pwm1_auto_channels_zone.dev_attr.attr, - &sensor_dev_attr_pwm1_auto_pwm_min.dev_attr.attr, &sensor_dev_attr_pwm1_auto_point1_pwm.dev_attr.attr, &sensor_dev_attr_pwm1_auto_point2_pwm.dev_attr.attr, NULL @@ -1629,7 +1653,6 @@ static struct attribute *dme1737_pwm2_attr[] = { &sensor_dev_attr_pwm2_enable.dev_attr.attr, &sensor_dev_attr_pwm2_ramp_rate.dev_attr.attr, &sensor_dev_attr_pwm2_auto_channels_zone.dev_attr.attr, - &sensor_dev_attr_pwm2_auto_pwm_min.dev_attr.attr, &sensor_dev_attr_pwm2_auto_point1_pwm.dev_attr.attr, &sensor_dev_attr_pwm2_auto_point2_pwm.dev_attr.attr, NULL @@ -1640,7 +1663,6 @@ static struct attribute *dme1737_pwm3_attr[] = { &sensor_dev_attr_pwm3_enable.dev_attr.attr, &sensor_dev_attr_pwm3_ramp_rate.dev_attr.attr, &sensor_dev_attr_pwm3_auto_channels_zone.dev_attr.attr, - &sensor_dev_attr_pwm3_auto_pwm_min.dev_attr.attr, &sensor_dev_attr_pwm3_auto_point1_pwm.dev_attr.attr, &sensor_dev_attr_pwm3_auto_point2_pwm.dev_attr.attr, NULL @@ -1667,6 +1689,15 @@ static const struct attribute_group dme1737_pwm_group[] = { { .attrs = dme1737_pwm6_attr }, }; +/* The following struct holds misc PWM attributes, which are not available in + * all chips. Their creation depends on the chip type which is determined + * during module load. */ +static struct attribute *dme1737_pwm_misc_attr[] = { + &sensor_dev_attr_pwm1_auto_pwm_min.dev_attr.attr, + &sensor_dev_attr_pwm2_auto_pwm_min.dev_attr.attr, + &sensor_dev_attr_pwm3_auto_pwm_min.dev_attr.attr, +}; + /* The following structs hold the fan attributes, some of which are optional. * Their creation depends on the chip configuration which is determined during * module load. */ @@ -1722,31 +1753,23 @@ static const struct attribute_group dme1737_fan_group[] = { { .attrs = dme1737_fan6_attr }, }; -/* The permissions of all of the following attributes are changed to read- +/* The permissions of the following zone attributes are changed to read- * writeable if the chip is *not* locked. Otherwise they stay read-only. */ -static struct attribute *dme1737_misc_chmod_attr[] = { - /* Temperatures */ - &sensor_dev_attr_temp1_offset.dev_attr.attr, - &sensor_dev_attr_temp2_offset.dev_attr.attr, - &sensor_dev_attr_temp3_offset.dev_attr.attr, - /* Zones */ - &sensor_dev_attr_zone1_auto_point1_temp_hyst.dev_attr.attr, +static struct attribute *dme1737_zone_chmod_attr[] = { &sensor_dev_attr_zone1_auto_point1_temp.dev_attr.attr, &sensor_dev_attr_zone1_auto_point2_temp.dev_attr.attr, &sensor_dev_attr_zone1_auto_point3_temp.dev_attr.attr, - &sensor_dev_attr_zone2_auto_point1_temp_hyst.dev_attr.attr, &sensor_dev_attr_zone2_auto_point1_temp.dev_attr.attr, &sensor_dev_attr_zone2_auto_point2_temp.dev_attr.attr, &sensor_dev_attr_zone2_auto_point3_temp.dev_attr.attr, - &sensor_dev_attr_zone3_auto_point1_temp_hyst.dev_attr.attr, &sensor_dev_attr_zone3_auto_point1_temp.dev_attr.attr, &sensor_dev_attr_zone3_auto_point2_temp.dev_attr.attr, &sensor_dev_attr_zone3_auto_point3_temp.dev_attr.attr, NULL }; -static const struct attribute_group dme1737_misc_chmod_group = { - .attrs = dme1737_misc_chmod_attr, +static const struct attribute_group dme1737_zone_chmod_group = { + .attrs = dme1737_zone_chmod_attr, }; /* The permissions of the following PWM attributes are changed to read- @@ -1757,7 +1780,6 @@ static struct attribute *dme1737_pwm1_chmod_attr[] = { &sensor_dev_attr_pwm1_enable.dev_attr.attr, &sensor_dev_attr_pwm1_ramp_rate.dev_attr.attr, &sensor_dev_attr_pwm1_auto_channels_zone.dev_attr.attr, - &sensor_dev_attr_pwm1_auto_pwm_min.dev_attr.attr, &sensor_dev_attr_pwm1_auto_point1_pwm.dev_attr.attr, NULL }; @@ -1766,7 +1788,6 @@ static struct attribute *dme1737_pwm2_chmod_attr[] = { &sensor_dev_attr_pwm2_enable.dev_attr.attr, &sensor_dev_attr_pwm2_ramp_rate.dev_attr.attr, &sensor_dev_attr_pwm2_auto_channels_zone.dev_attr.attr, - &sensor_dev_attr_pwm2_auto_pwm_min.dev_attr.attr, &sensor_dev_attr_pwm2_auto_point1_pwm.dev_attr.attr, NULL }; @@ -1775,7 +1796,6 @@ static struct attribute *dme1737_pwm3_chmod_attr[] = { &sensor_dev_attr_pwm3_enable.dev_attr.attr, &sensor_dev_attr_pwm3_ramp_rate.dev_attr.attr, &sensor_dev_attr_pwm3_auto_channels_zone.dev_attr.attr, - &sensor_dev_attr_pwm3_auto_pwm_min.dev_attr.attr, &sensor_dev_attr_pwm3_auto_point1_pwm.dev_attr.attr, NULL }; @@ -1875,9 +1895,17 @@ static void dme1737_remove_files(struct device *dev) if (data->has_pwm & (1 << ix)) { sysfs_remove_group(&dev->kobj, &dme1737_pwm_group[ix]); + if (data->type != sch5027 && ix < 3) { + sysfs_remove_file(&dev->kobj, + dme1737_pwm_misc_attr[ix]); + } } } + if (data->type != sch5027) { + sysfs_remove_group(&dev->kobj, &dme1737_misc_group); + } + sysfs_remove_group(&dev->kobj, &dme1737_group); if (!data->client.driver) { @@ -1901,6 +1929,13 @@ static int dme1737_create_files(struct device *dev) goto exit_remove; } + /* Create misc sysfs attributes */ + if ((data->type != sch5027) && + (err = sysfs_create_group(&dev->kobj, + &dme1737_misc_group))) { + goto exit_remove; + } + /* Create fan sysfs attributes */ for (ix = 0; ix < ARRAY_SIZE(dme1737_fan_group); ix++) { if (data->has_fan & (1 << ix)) { @@ -1918,6 +1953,11 @@ static int dme1737_create_files(struct device *dev) &dme1737_pwm_group[ix]))) { goto exit_remove; } + if (data->type != sch5027 && ix < 3 && + (err = sysfs_create_file(&dev->kobj, + dme1737_pwm_misc_attr[ix]))) { + goto exit_remove; + } } } @@ -1927,16 +1967,27 @@ static int dme1737_create_files(struct device *dev) dev_info(dev, "Device is locked. Some attributes " "will be read-only.\n"); } else { - /* Change permissions of standard sysfs attributes */ - dme1737_chmod_group(dev, &dme1737_misc_chmod_group, + /* Change permissions of zone sysfs attributes */ + dme1737_chmod_group(dev, &dme1737_zone_chmod_group, S_IRUGO | S_IWUSR); + /* Change permissions of misc sysfs attributes */ + if (data->type != sch5027) { + dme1737_chmod_group(dev, &dme1737_misc_group, + S_IRUGO | S_IWUSR); + } + /* Change permissions of PWM sysfs attributes */ for (ix = 0; ix < ARRAY_SIZE(dme1737_pwm_chmod_group); ix++) { if (data->has_pwm & (1 << ix)) { dme1737_chmod_group(dev, &dme1737_pwm_chmod_group[ix], S_IRUGO | S_IWUSR); + if (data->type != sch5027 && ix < 3) { + dme1737_chmod_file(dev, + dme1737_pwm_misc_attr[ix], + S_IRUGO | S_IWUSR); + } } } @@ -1966,6 +2017,9 @@ static int dme1737_init_device(struct device *dev) int ix; u8 reg; + /* Point to the right nominal voltages array */ + data->in_nominal = IN_NOMINAL(data->type); + data->config = dme1737_read(client, DME1737_REG_CONFIG); /* Inform if part is not monitoring/started */ if (!(data->config & 0x01)) { @@ -2076,7 +2130,9 @@ static int dme1737_init_device(struct device *dev) data->pwm_acz[2] = 4; /* pwm3 -> zone3 */ /* Set VRM */ - data->vrm = vid_which_vrm(); + if (data->type != sch5027) { + data->vrm = vid_which_vrm(); + } return 0; } @@ -2095,9 +2151,10 @@ static int dme1737_i2c_get_features(int sio_cip, struct dme1737_data *data) dme1737_sio_enter(sio_cip); /* Check device ID - * The DME1737 can return either 0x78 or 0x77 as its device ID. */ + * The DME1737 can return either 0x78 or 0x77 as its device ID. + * The SCH5027 returns 0x89 as its device ID. */ reg = force_id ? force_id : dme1737_sio_inb(sio_cip, 0x20); - if (!(reg == 0x77 || reg == 0x78)) { + if (!(reg == 0x77 || reg == 0x78 || reg == 0x89)) { err = -ENODEV; goto exit; } @@ -2166,15 +2223,24 @@ static int dme1737_i2c_detect(struct i2c_adapter *adapter, int address, company = dme1737_read(client, DME1737_REG_COMPANY); verstep = dme1737_read(client, DME1737_REG_VERSTEP); - if (!((company == DME1737_COMPANY_SMSC) && - ((verstep & DME1737_VERSTEP_MASK) == DME1737_VERSTEP))) { + if (company == DME1737_COMPANY_SMSC && + (verstep & DME1737_VERSTEP_MASK) == DME1737_VERSTEP) { + kind = dme1737; + } else if (company == DME1737_COMPANY_SMSC && + verstep == SCH5027_VERSTEP) { + kind = sch5027; + } else { err = -ENODEV; goto exit_kfree; } } - kind = dme1737; - name = "dme1737"; + if (kind == sch5027) { + name = "sch5027"; + } else { + kind = dme1737; + name = "dme1737"; + } data->type = kind; /* Fill in the remaining client fields and put it into the global @@ -2187,8 +2253,9 @@ static int dme1737_i2c_detect(struct i2c_adapter *adapter, int address, goto exit_kfree; } - dev_info(dev, "Found a DME1737 chip at 0x%02x (rev 0x%02x).\n", - client->addr, verstep); + dev_info(dev, "Found a %s chip at 0x%02x (rev 0x%02x).\n", + kind == sch5027 ? "SCH5027" : "DME1737", client->addr, + verstep); /* Initialize the DME1737 chip */ if ((err = dme1737_init_device(dev))) { @@ -2371,7 +2438,7 @@ static int __devinit dme1737_isa_probe(struct platform_device *pdev) goto exit_kfree; } } - data->type = -1; + data->type = sch311x; /* Fill in the remaining client fields and initialize the mutex */ strlcpy(client->name, "sch311x", I2C_NAME_SIZE); -- 2.39.5