From 3cd2cfeae187fb754f9530e3f919256f350e89ca Mon Sep 17 00:00:00 2001 From: "J. Bruce Fields" Date: Mon, 2 Jun 2008 16:01:51 -0400 Subject: [PATCH] nfs: rewrap NFS/RDMA documentation to 80 lines Wrap long lines. Signed-off-by: J. Bruce Fields --- Documentation/filesystems/nfs-rdma.txt | 40 ++++++++++++++------------ 1 file changed, 21 insertions(+), 19 deletions(-) diff --git a/Documentation/filesystems/nfs-rdma.txt b/Documentation/filesystems/nfs-rdma.txt index 9ad453d489..44bd766f2e 100644 --- a/Documentation/filesystems/nfs-rdma.txt +++ b/Documentation/filesystems/nfs-rdma.txt @@ -63,10 +63,10 @@ Installation - Install nfs-utils-1.1.2 or greater on the client An NFS/RDMA mount point can be obtained by using the mount.nfs command in - nfs-utils-1.1.2 or greater (nfs-utils-1.1.1 was the first nfs-utils version - with support for NFS/RDMA mounts, but for various reasons we recommend using - nfs-utils-1.1.2 or greater). To see which version of mount.nfs you are - using, type: + nfs-utils-1.1.2 or greater (nfs-utils-1.1.1 was the first nfs-utils + version with support for NFS/RDMA mounts, but for various reasons we + recommend using nfs-utils-1.1.2 or greater). To see which version of + mount.nfs you are using, type: $ /sbin/mount.nfs -V @@ -91,8 +91,9 @@ Installation After building the nfs-utils package, there will be a mount.nfs binary in the utils/mount directory. This binary can be used to initiate NFS v2, v3, - or v4 mounts. To initiate a v4 mount, the binary must be called mount.nfs4. - The standard technique is to create a symlink called mount.nfs4 to mount.nfs. + or v4 mounts. To initiate a v4 mount, the binary must be called + mount.nfs4. The standard technique is to create a symlink called + mount.nfs4 to mount.nfs. This mount.nfs binary should be installed at /sbin/mount.nfs as follows: @@ -214,11 +215,11 @@ NFS/RDMA Setup /vol0 192.168.0.47(fsid=0,rw,async,insecure,no_root_squash) /vol0 192.168.0.0/255.255.255.0(fsid=0,rw,async,insecure,no_root_squash) - The IP address(es) is(are) the client's IPoIB address for an InfiniBand HCA or the - cleint's iWARP address(es) for an RNIC. + The IP address(es) is(are) the client's IPoIB address for an InfiniBand + HCA or the cleint's iWARP address(es) for an RNIC. - NOTE: The "insecure" option must be used because the NFS/RDMA client does not - use a reserved port. + NOTE: The "insecure" option must be used because the NFS/RDMA client does + not use a reserved port. Each time a machine boots: @@ -234,12 +235,13 @@ NFS/RDMA Setup - Start the NFS server - If the NFS/RDMA server was built as a module (CONFIG_SUNRPC_XPRT_RDMA=m in kernel config), - load the RDMA transport module: + If the NFS/RDMA server was built as a module (CONFIG_SUNRPC_XPRT_RDMA=m in + kernel config), load the RDMA transport module: $ modprobe svcrdma - Regardless of how the server was built (module or built-in), start the server: + Regardless of how the server was built (module or built-in), start the + server: $ /etc/init.d/nfs start @@ -253,17 +255,17 @@ NFS/RDMA Setup - On the client system - If the NFS/RDMA client was built as a module (CONFIG_SUNRPC_XPRT_RDMA=m in kernel config), - load the RDMA client module: + If the NFS/RDMA client was built as a module (CONFIG_SUNRPC_XPRT_RDMA=m in + kernel config), load the RDMA client module: $ modprobe xprtrdma.ko - Regardless of how the client was built (module or built-in), use this command to - mount the NFS/RDMA server: + Regardless of how the client was built (module or built-in), use this + command to mount the NFS/RDMA server: $ mount -o rdma,port=2050 :/ /mnt - To verify that the mount is using RDMA, run "cat /proc/mounts" and check the - "proto" field for the given mount. + To verify that the mount is using RDMA, run "cat /proc/mounts" and check + the "proto" field for the given mount. Congratulations! You're using NFS/RDMA! -- 2.39.5