From 2bf34a1ca9d570dd4fab4d95c4de82d873ecf718 Mon Sep 17 00:00:00 2001 From: "R.Marek@sh.cvut.cz" Date: Thu, 26 May 2005 12:42:11 +0000 Subject: [PATCH] [PATCH] I2C: documentation update 1/3 This patch just changes the extension of Documentation/i2c/chips/smsc47b397.txt to none - to conform with naming in i2c subsystem directory. Signed-off-by: Rudolf Marek Signed-off-by: Greg Kroah-Hartman --- .../i2c/chips/{smsc47b397.txt => smsc47b397} | 24 +++++++++---------- 1 file changed, 12 insertions(+), 12 deletions(-) rename Documentation/i2c/chips/{smsc47b397.txt => smsc47b397} (90%) diff --git a/Documentation/i2c/chips/smsc47b397.txt b/Documentation/i2c/chips/smsc47b397 similarity index 90% rename from Documentation/i2c/chips/smsc47b397.txt rename to Documentation/i2c/chips/smsc47b397 index 389edae7f8..4737bb6109 100644 --- a/Documentation/i2c/chips/smsc47b397.txt +++ b/Documentation/i2c/chips/smsc47b397 @@ -72,20 +72,20 @@ To program the configuration registers, the following sequence must be followed: Enter Configuration Mode To place the chip into the Configuration State The config key (0x55) is written -to the CONFIG PORT (0x2E). +to the CONFIG PORT (0x2E). Configuration Mode In configuration mode, the INDEX PORT is located at the CONFIG PORT address and the DATA PORT is at INDEX PORT address + 1. -The desired configuration registers are accessed in two steps: +The desired configuration registers are accessed in two steps: a. Write the index of the Logical Device Number Configuration Register (i.e., 0x07) to the INDEX PORT and then write the number of the desired logical device to the DATA PORT. b. Write the address of the desired configuration register within the logical device to the INDEX PORT and then write or read the config- - uration register through the DATA PORT. + uration register through the DATA PORT. Note: If accessing the Global Configuration Registers, step (a) is not required. @@ -96,18 +96,18 @@ The chip returns to the RUN State. (This is important). Programming Example The following is an example of how to read the SIO Device ID located at 0x20 -; ENTER CONFIGURATION MODE +; ENTER CONFIGURATION MODE MOV DX,02EH MOV AX,055H OUT DX,AL -; GLOBAL CONFIGURATION REGISTER +; GLOBAL CONFIGURATION REGISTER MOV DX,02EH MOV AL,20H -OUT DX,AL +OUT DX,AL ; READ THE DATA MOV DX,02FH IN AL,DX -; EXIT CONFIGURATION MODE +; EXIT CONFIGURATION MODE MOV DX,02EH MOV AX,0AAH OUT DX,AL @@ -122,12 +122,12 @@ Obtaining the HWM Base Address. The following is an example of how to read the HWM Base Address located in Logical Device 8. -; ENTER CONFIGURATION MODE +; ENTER CONFIGURATION MODE MOV DX,02EH MOV AX,055H OUT DX,AL -; CONFIGURE REGISTER CRE0, -; LOGICAL DEVICE 8 +; CONFIGURE REGISTER CRE0, +; LOGICAL DEVICE 8 MOV DX,02EH MOV AL,07H OUT DX,AL ;Point to LD# Config Reg @@ -135,12 +135,12 @@ MOV DX,02FH MOV AL, 08H OUT DX,AL;Point to Logical Device 8 ; -MOV DX,02EH +MOV DX,02EH MOV AL,60H OUT DX,AL ; Point to HWM Base Addr MSB MOV DX,02FH IN AL,DX ; Get MSB of HWM Base Addr -; EXIT CONFIGURATION MODE +; EXIT CONFIGURATION MODE MOV DX,02EH MOV AX,0AAH OUT DX,AL -- 2.39.5