From 026d02a236f429eb61a1277166bd425f8514c431 Mon Sep 17 00:00:00 2001 From: Russell King Date: Wed, 29 Jun 2005 18:45:19 +0100 Subject: [PATCH] [PATCH] Serial: Split 8250 port table (part 2) Remove legacy ISA serial ports for Accent, Boca, Fourport, Hub6 and MCA from the architecture specific serial.h include. The only ports which remain in asm-*/serial.h are the platform specific entries. These should really be converted by platform maintainers to use a platform device, such as can be found in arch/arm/mach-footbridge/isa.c Signed-off-by: Russell King --- arch/parisc/configs/712_defconfig | 2 +- arch/parisc/configs/a500_defconfig | 2 +- arch/parisc/configs/b180_defconfig | 2 +- arch/parisc/configs/c3000_defconfig | 2 +- arch/parisc/defconfig | 2 +- drivers/serial/8250.c | 2 +- drivers/serial/Kconfig | 2 +- include/asm-alpha/serial.h | 47 +------------ include/asm-arm26/serial.h | 22 +----- include/asm-i386/serial.h | 102 +--------------------------- include/asm-m68k/serial.h | 47 +------------ include/asm-mips/serial.h | 84 ----------------------- include/asm-parisc/serial.h | 16 +---- include/asm-ppc/pc_serial.h | 86 +---------------------- include/asm-sh/bigsur/serial.h | 5 +- include/asm-sh/ec3104/serial.h | 4 +- include/asm-sh/serial.h | 6 +- include/asm-sh64/serial.h | 4 +- include/asm-x86_64/serial.h | 102 +--------------------------- 19 files changed, 20 insertions(+), 519 deletions(-) diff --git a/arch/parisc/configs/712_defconfig b/arch/parisc/configs/712_defconfig index 872085dea8..6efaa9293e 100644 --- a/arch/parisc/configs/712_defconfig +++ b/arch/parisc/configs/712_defconfig @@ -506,7 +506,7 @@ CONFIG_HW_CONSOLE=y # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y -CONFIG_SERIAL_8250_NR_UARTS=8 +CONFIG_SERIAL_8250_NR_UARTS=17 CONFIG_SERIAL_8250_EXTENDED=y CONFIG_SERIAL_8250_MANY_PORTS=y CONFIG_SERIAL_8250_SHARE_IRQ=y diff --git a/arch/parisc/configs/a500_defconfig b/arch/parisc/configs/a500_defconfig index d28ebfa107..30fc03ed0c 100644 --- a/arch/parisc/configs/a500_defconfig +++ b/arch/parisc/configs/a500_defconfig @@ -662,7 +662,7 @@ CONFIG_HW_CONSOLE=y CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y CONFIG_SERIAL_8250_CS=m -CONFIG_SERIAL_8250_NR_UARTS=8 +CONFIG_SERIAL_8250_NR_UARTS=17 CONFIG_SERIAL_8250_EXTENDED=y CONFIG_SERIAL_8250_MANY_PORTS=y CONFIG_SERIAL_8250_SHARE_IRQ=y diff --git a/arch/parisc/configs/b180_defconfig b/arch/parisc/configs/b180_defconfig index 1700d7aec6..46c9511f32 100644 --- a/arch/parisc/configs/b180_defconfig +++ b/arch/parisc/configs/b180_defconfig @@ -514,7 +514,7 @@ CONFIG_HW_CONSOLE=y # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y -CONFIG_SERIAL_8250_NR_UARTS=4 +CONFIG_SERIAL_8250_NR_UARTS=13 CONFIG_SERIAL_8250_EXTENDED=y CONFIG_SERIAL_8250_MANY_PORTS=y CONFIG_SERIAL_8250_SHARE_IRQ=y diff --git a/arch/parisc/configs/c3000_defconfig b/arch/parisc/configs/c3000_defconfig index b27980161c..67aca6ccc9 100644 --- a/arch/parisc/configs/c3000_defconfig +++ b/arch/parisc/configs/c3000_defconfig @@ -661,7 +661,7 @@ CONFIG_HW_CONSOLE=y # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y -CONFIG_SERIAL_8250_NR_UARTS=4 +CONFIG_SERIAL_8250_NR_UARTS=13 CONFIG_SERIAL_8250_EXTENDED=y CONFIG_SERIAL_8250_MANY_PORTS=y CONFIG_SERIAL_8250_SHARE_IRQ=y diff --git a/arch/parisc/defconfig b/arch/parisc/defconfig index ebd6301aa5..fdae21c503 100644 --- a/arch/parisc/defconfig +++ b/arch/parisc/defconfig @@ -517,7 +517,7 @@ CONFIG_HW_CONSOLE=y # CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y -CONFIG_SERIAL_8250_NR_UARTS=4 +CONFIG_SERIAL_8250_NR_UARTS=13 CONFIG_SERIAL_8250_EXTENDED=y CONFIG_SERIAL_8250_MANY_PORTS=y CONFIG_SERIAL_8250_SHARE_IRQ=y diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c index 429994d5bc..9224fc3184 100644 --- a/drivers/serial/8250.c +++ b/drivers/serial/8250.c @@ -105,7 +105,7 @@ static struct old_serial_port old_serial_port[] = { SERIAL_PORT_DFNS /* defined in asm/serial.h */ }; -#define UART_NR (ARRAY_SIZE(old_serial_port) + CONFIG_SERIAL_8250_NR_UARTS) +#define UART_NR CONFIG_SERIAL_8250_NR_UARTS #ifdef CONFIG_SERIAL_8250_RSA diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig index e879bce160..e0d0a470dd 100644 --- a/drivers/serial/Kconfig +++ b/drivers/serial/Kconfig @@ -86,7 +86,7 @@ config SERIAL_8250_ACPI namespace, say Y here. If unsure, say N. config SERIAL_8250_NR_UARTS - int "Maximum number of non-legacy 8250/16550 serial ports" + int "Maximum number of 8250/16550 serial ports" depends on SERIAL_8250 default "4" help diff --git a/include/asm-alpha/serial.h b/include/asm-alpha/serial.h index 7b2d9ee95a..7e4b2987d4 100644 --- a/include/asm-alpha/serial.h +++ b/include/asm-alpha/serial.h @@ -22,54 +22,9 @@ #define STD_COM4_FLAGS ASYNC_BOOT_AUTOCONF #endif -#ifdef CONFIG_SERIAL_MANY_PORTS -#define FOURPORT_FLAGS ASYNC_FOURPORT -#define ACCENT_FLAGS 0 -#define BOCA_FLAGS 0 -#endif - -#define STD_SERIAL_PORT_DEFNS \ +#define SERIAL_PORT_DFNS \ /* UART CLK PORT IRQ FLAGS */ \ { 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \ { 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS }, /* ttyS1 */ \ { 0, BASE_BAUD, 0x3E8, 4, STD_COM_FLAGS }, /* ttyS2 */ \ { 0, BASE_BAUD, 0x2E8, 3, STD_COM4_FLAGS }, /* ttyS3 */ - - -#ifdef CONFIG_SERIAL_MANY_PORTS -#define EXTRA_SERIAL_PORT_DEFNS \ - { 0, BASE_BAUD, 0x1A0, 9, FOURPORT_FLAGS }, /* ttyS4 */ \ - { 0, BASE_BAUD, 0x1A8, 9, FOURPORT_FLAGS }, /* ttyS5 */ \ - { 0, BASE_BAUD, 0x1B0, 9, FOURPORT_FLAGS }, /* ttyS6 */ \ - { 0, BASE_BAUD, 0x1B8, 9, FOURPORT_FLAGS }, /* ttyS7 */ \ - { 0, BASE_BAUD, 0x2A0, 5, FOURPORT_FLAGS }, /* ttyS8 */ \ - { 0, BASE_BAUD, 0x2A8, 5, FOURPORT_FLAGS }, /* ttyS9 */ \ - { 0, BASE_BAUD, 0x2B0, 5, FOURPORT_FLAGS }, /* ttyS10 */ \ - { 0, BASE_BAUD, 0x2B8, 5, FOURPORT_FLAGS }, /* ttyS11 */ \ - { 0, BASE_BAUD, 0x330, 4, ACCENT_FLAGS }, /* ttyS12 */ \ - { 0, BASE_BAUD, 0x338, 4, ACCENT_FLAGS }, /* ttyS13 */ \ - { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS14 (spare) */ \ - { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS15 (spare) */ \ - { 0, BASE_BAUD, 0x100, 12, BOCA_FLAGS }, /* ttyS16 */ \ - { 0, BASE_BAUD, 0x108, 12, BOCA_FLAGS }, /* ttyS17 */ \ - { 0, BASE_BAUD, 0x110, 12, BOCA_FLAGS }, /* ttyS18 */ \ - { 0, BASE_BAUD, 0x118, 12, BOCA_FLAGS }, /* ttyS19 */ \ - { 0, BASE_BAUD, 0x120, 12, BOCA_FLAGS }, /* ttyS20 */ \ - { 0, BASE_BAUD, 0x128, 12, BOCA_FLAGS }, /* ttyS21 */ \ - { 0, BASE_BAUD, 0x130, 12, BOCA_FLAGS }, /* ttyS22 */ \ - { 0, BASE_BAUD, 0x138, 12, BOCA_FLAGS }, /* ttyS23 */ \ - { 0, BASE_BAUD, 0x140, 12, BOCA_FLAGS }, /* ttyS24 */ \ - { 0, BASE_BAUD, 0x148, 12, BOCA_FLAGS }, /* ttyS25 */ \ - { 0, BASE_BAUD, 0x150, 12, BOCA_FLAGS }, /* ttyS26 */ \ - { 0, BASE_BAUD, 0x158, 12, BOCA_FLAGS }, /* ttyS27 */ \ - { 0, BASE_BAUD, 0x160, 12, BOCA_FLAGS }, /* ttyS28 */ \ - { 0, BASE_BAUD, 0x168, 12, BOCA_FLAGS }, /* ttyS29 */ \ - { 0, BASE_BAUD, 0x170, 12, BOCA_FLAGS }, /* ttyS30 */ \ - { 0, BASE_BAUD, 0x178, 12, BOCA_FLAGS }, /* ttyS31 */ -#else -#define EXTRA_SERIAL_PORT_DEFNS -#endif - -#define SERIAL_PORT_DFNS \ - STD_SERIAL_PORT_DEFNS \ - EXTRA_SERIAL_PORT_DEFNS diff --git a/include/asm-arm26/serial.h b/include/asm-arm26/serial.h index 21e1df31f0..5fc747d1b5 100644 --- a/include/asm-arm26/serial.h +++ b/include/asm-arm26/serial.h @@ -30,34 +30,16 @@ #if defined(CONFIG_ARCH_A5K) /* UART CLK PORT IRQ FLAGS */ -#define STD_SERIAL_PORT_DEFNS \ +#define SERIAL_PORT_DFNS \ { 0, BASE_BAUD, 0x3F8, 10, STD_COM_FLAGS }, /* ttyS0 */ \ { 0, BASE_BAUD, 0x2F8, 10, STD_COM_FLAGS }, /* ttyS1 */ #else -#define STD_SERIAL_PORT_DEFNS \ +#define SERIAL_PORT_DFNS \ { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS0 */ \ { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS1 */ #endif -#define EXTRA_SERIAL_PORT_DEFNS \ - { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS2 */ \ - { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS3 */ \ - { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS4 */ \ - { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS5 */ \ - { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS6 */ \ - { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS7 */ \ - { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS8 */ \ - { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS9 */ \ - { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS10 */ \ - { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS11 */ \ - { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS12 */ \ - { 0, BASE_BAUD, 0 , 0, STD_COM_FLAGS }, /* ttyS13 */ - -#define SERIAL_PORT_DFNS \ - STD_SERIAL_PORT_DEFNS \ - EXTRA_SERIAL_PORT_DEFNS - #endif diff --git a/include/asm-i386/serial.h b/include/asm-i386/serial.h index 21ddecc77c..e1ecfccb74 100644 --- a/include/asm-i386/serial.h +++ b/include/asm-i386/serial.h @@ -22,109 +22,9 @@ #define STD_COM4_FLAGS ASYNC_BOOT_AUTOCONF #endif -#ifdef CONFIG_SERIAL_MANY_PORTS -#define FOURPORT_FLAGS ASYNC_FOURPORT -#define ACCENT_FLAGS 0 -#define BOCA_FLAGS 0 -#define HUB6_FLAGS 0 -#endif - -#define MCA_COM_FLAGS (STD_COM_FLAGS|ASYNC_BOOT_ONLYMCA) - -/* - * The following define the access methods for the HUB6 card. All - * access is through two ports for all 24 possible chips. The card is - * selected through the high 2 bits, the port on that card with the - * "middle" 3 bits, and the register on that port with the bottom - * 3 bits. - * - * While the access port and interrupt is configurable, the default - * port locations are 0x302 for the port control register, and 0x303 - * for the data read/write register. Normally, the interrupt is at irq3 - * but can be anything from 3 to 7 inclusive. Note that using 3 will - * require disabling com2. - */ - -#define C_P(card,port) (((card)<<6|(port)<<3) + 1) - -#define STD_SERIAL_PORT_DEFNS \ +#define SERIAL_PORT_DFNS \ /* UART CLK PORT IRQ FLAGS */ \ { 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \ { 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS }, /* ttyS1 */ \ { 0, BASE_BAUD, 0x3E8, 4, STD_COM_FLAGS }, /* ttyS2 */ \ { 0, BASE_BAUD, 0x2E8, 3, STD_COM4_FLAGS }, /* ttyS3 */ - - -#ifdef CONFIG_SERIAL_MANY_PORTS -#define EXTRA_SERIAL_PORT_DEFNS \ - { 0, BASE_BAUD, 0x1A0, 9, FOURPORT_FLAGS }, /* ttyS4 */ \ - { 0, BASE_BAUD, 0x1A8, 9, FOURPORT_FLAGS }, /* ttyS5 */ \ - { 0, BASE_BAUD, 0x1B0, 9, FOURPORT_FLAGS }, /* ttyS6 */ \ - { 0, BASE_BAUD, 0x1B8, 9, FOURPORT_FLAGS }, /* ttyS7 */ \ - { 0, BASE_BAUD, 0x2A0, 5, FOURPORT_FLAGS }, /* ttyS8 */ \ - { 0, BASE_BAUD, 0x2A8, 5, FOURPORT_FLAGS }, /* ttyS9 */ \ - { 0, BASE_BAUD, 0x2B0, 5, FOURPORT_FLAGS }, /* ttyS10 */ \ - { 0, BASE_BAUD, 0x2B8, 5, FOURPORT_FLAGS }, /* ttyS11 */ \ - { 0, BASE_BAUD, 0x330, 4, ACCENT_FLAGS }, /* ttyS12 */ \ - { 0, BASE_BAUD, 0x338, 4, ACCENT_FLAGS }, /* ttyS13 */ \ - { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS14 (spare) */ \ - { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS15 (spare) */ \ - { 0, BASE_BAUD, 0x100, 12, BOCA_FLAGS }, /* ttyS16 */ \ - { 0, BASE_BAUD, 0x108, 12, BOCA_FLAGS }, /* ttyS17 */ \ - { 0, BASE_BAUD, 0x110, 12, BOCA_FLAGS }, /* ttyS18 */ \ - { 0, BASE_BAUD, 0x118, 12, BOCA_FLAGS }, /* ttyS19 */ \ - { 0, BASE_BAUD, 0x120, 12, BOCA_FLAGS }, /* ttyS20 */ \ - { 0, BASE_BAUD, 0x128, 12, BOCA_FLAGS }, /* ttyS21 */ \ - { 0, BASE_BAUD, 0x130, 12, BOCA_FLAGS }, /* ttyS22 */ \ - { 0, BASE_BAUD, 0x138, 12, BOCA_FLAGS }, /* ttyS23 */ \ - { 0, BASE_BAUD, 0x140, 12, BOCA_FLAGS }, /* ttyS24 */ \ - { 0, BASE_BAUD, 0x148, 12, BOCA_FLAGS }, /* ttyS25 */ \ - { 0, BASE_BAUD, 0x150, 12, BOCA_FLAGS }, /* ttyS26 */ \ - { 0, BASE_BAUD, 0x158, 12, BOCA_FLAGS }, /* ttyS27 */ \ - { 0, BASE_BAUD, 0x160, 12, BOCA_FLAGS }, /* ttyS28 */ \ - { 0, BASE_BAUD, 0x168, 12, BOCA_FLAGS }, /* ttyS29 */ \ - { 0, BASE_BAUD, 0x170, 12, BOCA_FLAGS }, /* ttyS30 */ \ - { 0, BASE_BAUD, 0x178, 12, BOCA_FLAGS }, /* ttyS31 */ -#else -#define EXTRA_SERIAL_PORT_DEFNS -#endif - -/* You can have up to four HUB6's in the system, but I've only - * included two cards here for a total of twelve ports. - */ -#if (defined(CONFIG_HUB6) && defined(CONFIG_SERIAL_MANY_PORTS)) -#define HUB6_SERIAL_PORT_DFNS \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,0) }, /* ttyS32 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,1) }, /* ttyS33 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,2) }, /* ttyS34 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,3) }, /* ttyS35 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,4) }, /* ttyS36 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,5) }, /* ttyS37 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,0) }, /* ttyS38 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,1) }, /* ttyS39 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,2) }, /* ttyS40 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,3) }, /* ttyS41 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,4) }, /* ttyS42 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,5) }, /* ttyS43 */ -#else -#define HUB6_SERIAL_PORT_DFNS -#endif - -#ifdef CONFIG_MCA -#define MCA_SERIAL_PORT_DFNS \ - { 0, BASE_BAUD, 0x3220, 3, MCA_COM_FLAGS }, \ - { 0, BASE_BAUD, 0x3228, 3, MCA_COM_FLAGS }, \ - { 0, BASE_BAUD, 0x4220, 3, MCA_COM_FLAGS }, \ - { 0, BASE_BAUD, 0x4228, 3, MCA_COM_FLAGS }, \ - { 0, BASE_BAUD, 0x5220, 3, MCA_COM_FLAGS }, \ - { 0, BASE_BAUD, 0x5228, 3, MCA_COM_FLAGS }, -#else -#define MCA_SERIAL_PORT_DFNS -#endif - -#define SERIAL_PORT_DFNS \ - STD_SERIAL_PORT_DEFNS \ - EXTRA_SERIAL_PORT_DEFNS \ - HUB6_SERIAL_PORT_DFNS \ - MCA_SERIAL_PORT_DFNS - diff --git a/include/asm-m68k/serial.h b/include/asm-m68k/serial.h index 9f5bcdc105..3fe29f8b01 100644 --- a/include/asm-m68k/serial.h +++ b/include/asm-m68k/serial.h @@ -26,54 +26,9 @@ #define STD_COM4_FLAGS ASYNC_BOOT_AUTOCONF #endif -#ifdef CONFIG_SERIAL_MANY_PORTS -#define FOURPORT_FLAGS ASYNC_FOURPORT -#define ACCENT_FLAGS 0 -#define BOCA_FLAGS 0 -#endif - -#define STD_SERIAL_PORT_DEFNS \ +#define SERIAL_PORT_DFNS \ /* UART CLK PORT IRQ FLAGS */ \ { 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \ { 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS }, /* ttyS1 */ \ { 0, BASE_BAUD, 0x3E8, 4, STD_COM_FLAGS }, /* ttyS2 */ \ { 0, BASE_BAUD, 0x2E8, 3, STD_COM4_FLAGS }, /* ttyS3 */ - - -#ifdef CONFIG_SERIAL_MANY_PORTS -#define EXTRA_SERIAL_PORT_DEFNS \ - { 0, BASE_BAUD, 0x1A0, 9, FOURPORT_FLAGS }, /* ttyS4 */ \ - { 0, BASE_BAUD, 0x1A8, 9, FOURPORT_FLAGS }, /* ttyS5 */ \ - { 0, BASE_BAUD, 0x1B0, 9, FOURPORT_FLAGS }, /* ttyS6 */ \ - { 0, BASE_BAUD, 0x1B8, 9, FOURPORT_FLAGS }, /* ttyS7 */ \ - { 0, BASE_BAUD, 0x2A0, 5, FOURPORT_FLAGS }, /* ttyS8 */ \ - { 0, BASE_BAUD, 0x2A8, 5, FOURPORT_FLAGS }, /* ttyS9 */ \ - { 0, BASE_BAUD, 0x2B0, 5, FOURPORT_FLAGS }, /* ttyS10 */ \ - { 0, BASE_BAUD, 0x2B8, 5, FOURPORT_FLAGS }, /* ttyS11 */ \ - { 0, BASE_BAUD, 0x330, 4, ACCENT_FLAGS }, /* ttyS12 */ \ - { 0, BASE_BAUD, 0x338, 4, ACCENT_FLAGS }, /* ttyS13 */ \ - { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS14 (spare) */ \ - { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS15 (spare) */ \ - { 0, BASE_BAUD, 0x100, 12, BOCA_FLAGS }, /* ttyS16 */ \ - { 0, BASE_BAUD, 0x108, 12, BOCA_FLAGS }, /* ttyS17 */ \ - { 0, BASE_BAUD, 0x110, 12, BOCA_FLAGS }, /* ttyS18 */ \ - { 0, BASE_BAUD, 0x118, 12, BOCA_FLAGS }, /* ttyS19 */ \ - { 0, BASE_BAUD, 0x120, 12, BOCA_FLAGS }, /* ttyS20 */ \ - { 0, BASE_BAUD, 0x128, 12, BOCA_FLAGS }, /* ttyS21 */ \ - { 0, BASE_BAUD, 0x130, 12, BOCA_FLAGS }, /* ttyS22 */ \ - { 0, BASE_BAUD, 0x138, 12, BOCA_FLAGS }, /* ttyS23 */ \ - { 0, BASE_BAUD, 0x140, 12, BOCA_FLAGS }, /* ttyS24 */ \ - { 0, BASE_BAUD, 0x148, 12, BOCA_FLAGS }, /* ttyS25 */ \ - { 0, BASE_BAUD, 0x150, 12, BOCA_FLAGS }, /* ttyS26 */ \ - { 0, BASE_BAUD, 0x158, 12, BOCA_FLAGS }, /* ttyS27 */ \ - { 0, BASE_BAUD, 0x160, 12, BOCA_FLAGS }, /* ttyS28 */ \ - { 0, BASE_BAUD, 0x168, 12, BOCA_FLAGS }, /* ttyS29 */ \ - { 0, BASE_BAUD, 0x170, 12, BOCA_FLAGS }, /* ttyS30 */ \ - { 0, BASE_BAUD, 0x178, 12, BOCA_FLAGS }, /* ttyS31 */ -#else -#define EXTRA_SERIAL_PORT_DEFNS -#endif - -#define SERIAL_PORT_DFNS \ - STD_SERIAL_PORT_DEFNS \ - EXTRA_SERIAL_PORT_DEFNS diff --git a/include/asm-mips/serial.h b/include/asm-mips/serial.h index 8a70ff58f7..4eed8e2acd 100644 --- a/include/asm-mips/serial.h +++ b/include/asm-mips/serial.h @@ -29,32 +29,6 @@ #define STD_COM4_FLAGS ASYNC_BOOT_AUTOCONF #endif -#ifdef CONFIG_SERIAL_MANY_PORTS -#define FOURPORT_FLAGS ASYNC_FOURPORT -#define ACCENT_FLAGS 0 -#define BOCA_FLAGS 0 -#define HUB6_FLAGS 0 -#define RS_TABLE_SIZE 64 -#else -#define RS_TABLE_SIZE -#endif - -/* - * The following define the access methods for the HUB6 card. All - * access is through two ports for all 24 possible chips. The card is - * selected through the high 2 bits, the port on that card with the - * "middle" 3 bits, and the register on that port with the bottom - * 3 bits. - * - * While the access port and interrupt is configurable, the default - * port locations are 0x302 for the port control register, and 0x303 - * for the data read/write register. Normally, the interrupt is at irq3 - * but can be anything from 3 to 7 inclusive. Note that using 3 will - * require disabling com2. - */ - -#define C_P(card,port) (((card)<<6|(port)<<3) + 1) - #ifdef CONFIG_MACH_JAZZ #include @@ -240,66 +214,10 @@ { 0, BASE_BAUD, 0x3E8, 4, STD_COM_FLAGS }, /* ttyS2 */ \ { 0, BASE_BAUD, 0x2E8, 3, STD_COM4_FLAGS }, /* ttyS3 */ -#ifdef CONFIG_SERIAL_MANY_PORTS -#define EXTRA_SERIAL_PORT_DEFNS \ - { 0, BASE_BAUD, 0x1A0, 9, FOURPORT_FLAGS }, /* ttyS4 */ \ - { 0, BASE_BAUD, 0x1A8, 9, FOURPORT_FLAGS }, /* ttyS5 */ \ - { 0, BASE_BAUD, 0x1B0, 9, FOURPORT_FLAGS }, /* ttyS6 */ \ - { 0, BASE_BAUD, 0x1B8, 9, FOURPORT_FLAGS }, /* ttyS7 */ \ - { 0, BASE_BAUD, 0x2A0, 5, FOURPORT_FLAGS }, /* ttyS8 */ \ - { 0, BASE_BAUD, 0x2A8, 5, FOURPORT_FLAGS }, /* ttyS9 */ \ - { 0, BASE_BAUD, 0x2B0, 5, FOURPORT_FLAGS }, /* ttyS10 */ \ - { 0, BASE_BAUD, 0x2B8, 5, FOURPORT_FLAGS }, /* ttyS11 */ \ - { 0, BASE_BAUD, 0x330, 4, ACCENT_FLAGS }, /* ttyS12 */ \ - { 0, BASE_BAUD, 0x338, 4, ACCENT_FLAGS }, /* ttyS13 */ \ - { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS14 (spare) */ \ - { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS15 (spare) */ \ - { 0, BASE_BAUD, 0x100, 12, BOCA_FLAGS }, /* ttyS16 */ \ - { 0, BASE_BAUD, 0x108, 12, BOCA_FLAGS }, /* ttyS17 */ \ - { 0, BASE_BAUD, 0x110, 12, BOCA_FLAGS }, /* ttyS18 */ \ - { 0, BASE_BAUD, 0x118, 12, BOCA_FLAGS }, /* ttyS19 */ \ - { 0, BASE_BAUD, 0x120, 12, BOCA_FLAGS }, /* ttyS20 */ \ - { 0, BASE_BAUD, 0x128, 12, BOCA_FLAGS }, /* ttyS21 */ \ - { 0, BASE_BAUD, 0x130, 12, BOCA_FLAGS }, /* ttyS22 */ \ - { 0, BASE_BAUD, 0x138, 12, BOCA_FLAGS }, /* ttyS23 */ \ - { 0, BASE_BAUD, 0x140, 12, BOCA_FLAGS }, /* ttyS24 */ \ - { 0, BASE_BAUD, 0x148, 12, BOCA_FLAGS }, /* ttyS25 */ \ - { 0, BASE_BAUD, 0x150, 12, BOCA_FLAGS }, /* ttyS26 */ \ - { 0, BASE_BAUD, 0x158, 12, BOCA_FLAGS }, /* ttyS27 */ \ - { 0, BASE_BAUD, 0x160, 12, BOCA_FLAGS }, /* ttyS28 */ \ - { 0, BASE_BAUD, 0x168, 12, BOCA_FLAGS }, /* ttyS29 */ \ - { 0, BASE_BAUD, 0x170, 12, BOCA_FLAGS }, /* ttyS30 */ \ - { 0, BASE_BAUD, 0x178, 12, BOCA_FLAGS }, /* ttyS31 */ -#else /* CONFIG_SERIAL_MANY_PORTS */ -#define EXTRA_SERIAL_PORT_DEFNS -#endif /* CONFIG_SERIAL_MANY_PORTS */ - #else /* CONFIG_HAVE_STD_PC_SERIAL_PORTS */ #define STD_SERIAL_PORT_DEFNS -#define EXTRA_SERIAL_PORT_DEFNS #endif /* CONFIG_HAVE_STD_PC_SERIAL_PORTS */ -/* You can have up to four HUB6's in the system, but I've only - * included two cards here for a total of twelve ports. - */ -#if (defined(CONFIG_HUB6) && defined(CONFIG_SERIAL_MANY_PORTS)) -#define HUB6_SERIAL_PORT_DFNS \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,0) }, /* ttyS32 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,1) }, /* ttyS33 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,2) }, /* ttyS34 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,3) }, /* ttyS35 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,4) }, /* ttyS36 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,5) }, /* ttyS37 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,0) }, /* ttyS38 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,1) }, /* ttyS39 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,2) }, /* ttyS40 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,3) }, /* ttyS41 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,4) }, /* ttyS42 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,5) }, /* ttyS43 */ -#else -#define HUB6_SERIAL_PORT_DFNS -#endif - #ifdef CONFIG_MOMENCO_JAGUAR_ATX /* Ordinary NS16552 duart with a 20MHz crystal. */ #define JAGUAR_ATX_UART_CLK 20000000 @@ -427,8 +345,6 @@ COBALT_SERIAL_PORT_DEFNS \ DDB5477_SERIAL_PORT_DEFNS \ EV96100_SERIAL_PORT_DEFNS \ - EXTRA_SERIAL_PORT_DEFNS \ - HUB6_SERIAL_PORT_DFNS \ IP32_SERIAL_PORT_DEFNS \ ITE_SERIAL_PORT_DEFNS \ IVR_SERIAL_PORT_DEFNS \ diff --git a/include/asm-parisc/serial.h b/include/asm-parisc/serial.h index 239c5dcab7..82fd820d68 100644 --- a/include/asm-parisc/serial.h +++ b/include/asm-parisc/serial.h @@ -19,18 +19,4 @@ * A500 w/ PCI serial cards: 5 + 4 * card ~= 17 */ -#define STD_SERIAL_PORT_DEFNS \ - { 0, }, /* ttyS0 */ \ - { 0, }, /* ttyS1 */ \ - { 0, }, /* ttyS2 */ \ - { 0, }, /* ttyS3 */ \ - { 0, }, /* ttyS4 */ \ - { 0, }, /* ttyS5 */ \ - { 0, }, /* ttyS6 */ \ - { 0, }, /* ttyS7 */ \ - { 0, }, /* ttyS8 */ - - -#define SERIAL_PORT_DFNS \ - STD_SERIAL_PORT_DEFNS - +#define SERIAL_PORT_DFNS diff --git a/include/asm-ppc/pc_serial.h b/include/asm-ppc/pc_serial.h index fa9cbb67ce..8f994f9f88 100644 --- a/include/asm-ppc/pc_serial.h +++ b/include/asm-ppc/pc_serial.h @@ -35,93 +35,9 @@ #define STD_COM4_FLAGS ASYNC_BOOT_AUTOCONF #endif -#ifdef CONFIG_SERIAL_MANY_PORTS -#define FOURPORT_FLAGS ASYNC_FOURPORT -#define ACCENT_FLAGS 0 -#define BOCA_FLAGS 0 -#define HUB6_FLAGS 0 -#endif - -/* - * The following define the access methods for the HUB6 card. All - * access is through two ports for all 24 possible chips. The card is - * selected through the high 2 bits, the port on that card with the - * "middle" 3 bits, and the register on that port with the bottom - * 3 bits. - * - * While the access port and interrupt is configurable, the default - * port locations are 0x302 for the port control register, and 0x303 - * for the data read/write register. Normally, the interrupt is at irq3 - * but can be anything from 3 to 7 inclusive. Note that using 3 will - * require disabling com2. - */ - -#define C_P(card,port) (((card)<<6|(port)<<3) + 1) - -#define STD_SERIAL_PORT_DEFNS \ +#define SERIAL_PORT_DFNS \ /* UART CLK PORT IRQ FLAGS */ \ { 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \ { 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS }, /* ttyS1 */ \ { 0, BASE_BAUD, 0x3E8, 4, STD_COM_FLAGS }, /* ttyS2 */ \ { 0, BASE_BAUD, 0x2E8, 3, STD_COM4_FLAGS }, /* ttyS3 */ - - -#ifdef CONFIG_SERIAL_MANY_PORTS -#define EXTRA_SERIAL_PORT_DEFNS \ - { 0, BASE_BAUD, 0x1A0, 9, FOURPORT_FLAGS }, /* ttyS4 */ \ - { 0, BASE_BAUD, 0x1A8, 9, FOURPORT_FLAGS }, /* ttyS5 */ \ - { 0, BASE_BAUD, 0x1B0, 9, FOURPORT_FLAGS }, /* ttyS6 */ \ - { 0, BASE_BAUD, 0x1B8, 9, FOURPORT_FLAGS }, /* ttyS7 */ \ - { 0, BASE_BAUD, 0x2A0, 5, FOURPORT_FLAGS }, /* ttyS8 */ \ - { 0, BASE_BAUD, 0x2A8, 5, FOURPORT_FLAGS }, /* ttyS9 */ \ - { 0, BASE_BAUD, 0x2B0, 5, FOURPORT_FLAGS }, /* ttyS10 */ \ - { 0, BASE_BAUD, 0x2B8, 5, FOURPORT_FLAGS }, /* ttyS11 */ \ - { 0, BASE_BAUD, 0x330, 4, ACCENT_FLAGS }, /* ttyS12 */ \ - { 0, BASE_BAUD, 0x338, 4, ACCENT_FLAGS }, /* ttyS13 */ \ - { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS14 (spare) */ \ - { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS15 (spare) */ \ - { 0, BASE_BAUD, 0x100, 12, BOCA_FLAGS }, /* ttyS16 */ \ - { 0, BASE_BAUD, 0x108, 12, BOCA_FLAGS }, /* ttyS17 */ \ - { 0, BASE_BAUD, 0x110, 12, BOCA_FLAGS }, /* ttyS18 */ \ - { 0, BASE_BAUD, 0x118, 12, BOCA_FLAGS }, /* ttyS19 */ \ - { 0, BASE_BAUD, 0x120, 12, BOCA_FLAGS }, /* ttyS20 */ \ - { 0, BASE_BAUD, 0x128, 12, BOCA_FLAGS }, /* ttyS21 */ \ - { 0, BASE_BAUD, 0x130, 12, BOCA_FLAGS }, /* ttyS22 */ \ - { 0, BASE_BAUD, 0x138, 12, BOCA_FLAGS }, /* ttyS23 */ \ - { 0, BASE_BAUD, 0x140, 12, BOCA_FLAGS }, /* ttyS24 */ \ - { 0, BASE_BAUD, 0x148, 12, BOCA_FLAGS }, /* ttyS25 */ \ - { 0, BASE_BAUD, 0x150, 12, BOCA_FLAGS }, /* ttyS26 */ \ - { 0, BASE_BAUD, 0x158, 12, BOCA_FLAGS }, /* ttyS27 */ \ - { 0, BASE_BAUD, 0x160, 12, BOCA_FLAGS }, /* ttyS28 */ \ - { 0, BASE_BAUD, 0x168, 12, BOCA_FLAGS }, /* ttyS29 */ \ - { 0, BASE_BAUD, 0x170, 12, BOCA_FLAGS }, /* ttyS30 */ \ - { 0, BASE_BAUD, 0x178, 12, BOCA_FLAGS }, /* ttyS31 */ -#else -#define EXTRA_SERIAL_PORT_DEFNS -#endif - -/* You can have up to four HUB6's in the system, but I've only - * included two cards here for a total of twelve ports. - */ -#if (defined(CONFIG_HUB6) && defined(CONFIG_SERIAL_MANY_PORTS)) -#define HUB6_SERIAL_PORT_DFNS \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,0) }, /* ttyS32 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,1) }, /* ttyS33 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,2) }, /* ttyS34 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,3) }, /* ttyS35 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,4) }, /* ttyS36 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,5) }, /* ttyS37 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,0) }, /* ttyS38 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,1) }, /* ttyS39 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,2) }, /* ttyS40 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,3) }, /* ttyS41 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,4) }, /* ttyS42 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,5) }, /* ttyS43 */ -#else -#define HUB6_SERIAL_PORT_DFNS -#endif - -#define SERIAL_PORT_DFNS \ - STD_SERIAL_PORT_DEFNS \ - EXTRA_SERIAL_PORT_DEFNS \ - HUB6_SERIAL_PORT_DFNS diff --git a/include/asm-sh/bigsur/serial.h b/include/asm-sh/bigsur/serial.h index 540f122059..7233af42f7 100644 --- a/include/asm-sh/bigsur/serial.h +++ b/include/asm-sh/bigsur/serial.h @@ -14,13 +14,10 @@ #define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST) -#define STD_SERIAL_PORT_DEFNS \ +#define SERIAL_PORT_DFNS \ /* UART CLK PORT IRQ FLAGS */ \ { 0, BASE_BAUD, 0x3F8, HD64465_IRQ_UART, STD_COM_FLAGS } /* ttyS0 */ - -#define SERIAL_PORT_DFNS STD_SERIAL_PORT_DEFNS - /* XXX: This should be moved ino irq.h */ #define irq_cannonicalize(x) (x) diff --git a/include/asm-sh/ec3104/serial.h b/include/asm-sh/ec3104/serial.h index f8eb16312e..cfe4d78ec1 100644 --- a/include/asm-sh/ec3104/serial.h +++ b/include/asm-sh/ec3104/serial.h @@ -10,13 +10,11 @@ * it's got the keyboard controller behind it so we can't really use it * (without moving the keyboard driver to userspace, which doesn't sound * like a very good idea) */ -#define STD_SERIAL_PORT_DEFNS \ +#define SERIAL_PORT_DFNS \ /* UART CLK PORT IRQ FLAGS */ \ { 0, BASE_BAUD, 0x11C00, EC3104_IRQBASE+7, STD_COM_FLAGS }, /* ttyS0 */ \ { 0, BASE_BAUD, 0x12000, EC3104_IRQBASE+8, STD_COM_FLAGS }, /* ttyS1 */ \ { 0, BASE_BAUD, 0x12400, EC3104_IRQBASE+9, STD_COM_FLAGS }, /* ttyS2 */ -#define SERIAL_PORT_DFNS STD_SERIAL_PORT_DEFNS - /* XXX: This should be moved ino irq.h */ #define irq_cannonicalize(x) (x) diff --git a/include/asm-sh/serial.h b/include/asm-sh/serial.h index 5474dbdbaa..f51e232d5c 100644 --- a/include/asm-sh/serial.h +++ b/include/asm-sh/serial.h @@ -29,20 +29,18 @@ #ifdef CONFIG_HD64465 #include -#define STD_SERIAL_PORT_DEFNS \ +#define SERIAL_PORT_DFNS \ /* UART CLK PORT IRQ FLAGS */ \ { 0, BASE_BAUD, 0x3F8, HD64465_IRQ_UART, STD_COM_FLAGS } /* ttyS0 */ #else -#define STD_SERIAL_PORT_DEFNS \ +#define SERIAL_PORT_DFNS \ /* UART CLK PORT IRQ FLAGS */ \ { 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \ { 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS } /* ttyS1 */ #endif -#define SERIAL_PORT_DFNS STD_SERIAL_PORT_DEFNS - #endif #endif /* _ASM_SERIAL_H */ diff --git a/include/asm-sh64/serial.h b/include/asm-sh64/serial.h index 8e39b4e90c..29c9be1511 100644 --- a/include/asm-sh64/serial.h +++ b/include/asm-sh64/serial.h @@ -20,13 +20,11 @@ #define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST) -#define STD_SERIAL_PORT_DEFNS \ +#define SERIAL_PORT_DFNS \ /* UART CLK PORT IRQ FLAGS */ \ { 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \ { 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS } /* ttyS1 */ -#define SERIAL_PORT_DFNS STD_SERIAL_PORT_DEFNS - /* XXX: This should be moved ino irq.h */ #define irq_cannonicalize(x) (x) diff --git a/include/asm-x86_64/serial.h b/include/asm-x86_64/serial.h index dbab232044..dc752eafa6 100644 --- a/include/asm-x86_64/serial.h +++ b/include/asm-x86_64/serial.h @@ -22,109 +22,9 @@ #define STD_COM4_FLAGS ASYNC_BOOT_AUTOCONF #endif -#ifdef CONFIG_SERIAL_MANY_PORTS -#define FOURPORT_FLAGS ASYNC_FOURPORT -#define ACCENT_FLAGS 0 -#define BOCA_FLAGS 0 -#define HUB6_FLAGS 0 -#endif - -#define MCA_COM_FLAGS (STD_COM_FLAGS|ASYNC_BOOT_ONLYMCA) - -/* - * The following define the access methods for the HUB6 card. All - * access is through two ports for all 24 possible chips. The card is - * selected through the high 2 bits, the port on that card with the - * "middle" 3 bits, and the register on that port with the bottom - * 3 bits. - * - * While the access port and interrupt is configurable, the default - * port locations are 0x302 for the port control register, and 0x303 - * for the data read/write register. Normally, the interrupt is at irq3 - * but can be anything from 3 to 7 inclusive. Note that using 3 will - * require disabling com2. - */ - -#define C_P(card,port) (((card)<<6|(port)<<3) + 1) - -#define STD_SERIAL_PORT_DEFNS \ +#define SERIAL_PORT_DFNS \ /* UART CLK PORT IRQ FLAGS */ \ { 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \ { 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS }, /* ttyS1 */ \ { 0, BASE_BAUD, 0x3E8, 4, STD_COM_FLAGS }, /* ttyS2 */ \ { 0, BASE_BAUD, 0x2E8, 3, STD_COM4_FLAGS }, /* ttyS3 */ - - -#ifdef CONFIG_SERIAL_MANY_PORTS -#define EXTRA_SERIAL_PORT_DEFNS \ - { 0, BASE_BAUD, 0x1A0, 9, FOURPORT_FLAGS }, /* ttyS4 */ \ - { 0, BASE_BAUD, 0x1A8, 9, FOURPORT_FLAGS }, /* ttyS5 */ \ - { 0, BASE_BAUD, 0x1B0, 9, FOURPORT_FLAGS }, /* ttyS6 */ \ - { 0, BASE_BAUD, 0x1B8, 9, FOURPORT_FLAGS }, /* ttyS7 */ \ - { 0, BASE_BAUD, 0x2A0, 5, FOURPORT_FLAGS }, /* ttyS8 */ \ - { 0, BASE_BAUD, 0x2A8, 5, FOURPORT_FLAGS }, /* ttyS9 */ \ - { 0, BASE_BAUD, 0x2B0, 5, FOURPORT_FLAGS }, /* ttyS10 */ \ - { 0, BASE_BAUD, 0x2B8, 5, FOURPORT_FLAGS }, /* ttyS11 */ \ - { 0, BASE_BAUD, 0x330, 4, ACCENT_FLAGS }, /* ttyS12 */ \ - { 0, BASE_BAUD, 0x338, 4, ACCENT_FLAGS }, /* ttyS13 */ \ - { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS14 (spare) */ \ - { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS15 (spare) */ \ - { 0, BASE_BAUD, 0x100, 12, BOCA_FLAGS }, /* ttyS16 */ \ - { 0, BASE_BAUD, 0x108, 12, BOCA_FLAGS }, /* ttyS17 */ \ - { 0, BASE_BAUD, 0x110, 12, BOCA_FLAGS }, /* ttyS18 */ \ - { 0, BASE_BAUD, 0x118, 12, BOCA_FLAGS }, /* ttyS19 */ \ - { 0, BASE_BAUD, 0x120, 12, BOCA_FLAGS }, /* ttyS20 */ \ - { 0, BASE_BAUD, 0x128, 12, BOCA_FLAGS }, /* ttyS21 */ \ - { 0, BASE_BAUD, 0x130, 12, BOCA_FLAGS }, /* ttyS22 */ \ - { 0, BASE_BAUD, 0x138, 12, BOCA_FLAGS }, /* ttyS23 */ \ - { 0, BASE_BAUD, 0x140, 12, BOCA_FLAGS }, /* ttyS24 */ \ - { 0, BASE_BAUD, 0x148, 12, BOCA_FLAGS }, /* ttyS25 */ \ - { 0, BASE_BAUD, 0x150, 12, BOCA_FLAGS }, /* ttyS26 */ \ - { 0, BASE_BAUD, 0x158, 12, BOCA_FLAGS }, /* ttyS27 */ \ - { 0, BASE_BAUD, 0x160, 12, BOCA_FLAGS }, /* ttyS28 */ \ - { 0, BASE_BAUD, 0x168, 12, BOCA_FLAGS }, /* ttyS29 */ \ - { 0, BASE_BAUD, 0x170, 12, BOCA_FLAGS }, /* ttyS30 */ \ - { 0, BASE_BAUD, 0x178, 12, BOCA_FLAGS }, /* ttyS31 */ -#else -#define EXTRA_SERIAL_PORT_DEFNS -#endif - -/* You can have up to four HUB6's in the system, but I've only - * included two cards here for a total of twelve ports. - */ -#if (defined(CONFIG_HUB6) && defined(CONFIG_SERIAL_MANY_PORTS)) -#define HUB6_SERIAL_PORT_DFNS \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,0) }, /* ttyS32 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,1) }, /* ttyS33 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,2) }, /* ttyS34 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,3) }, /* ttyS35 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,4) }, /* ttyS36 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,5) }, /* ttyS37 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,0) }, /* ttyS38 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,1) }, /* ttyS39 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,2) }, /* ttyS40 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,3) }, /* ttyS41 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,4) }, /* ttyS42 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,5) }, /* ttyS43 */ -#else -#define HUB6_SERIAL_PORT_DFNS -#endif - -#ifdef CONFIG_MCA -#define MCA_SERIAL_PORT_DFNS \ - { 0, BASE_BAUD, 0x3220, 3, MCA_COM_FLAGS }, \ - { 0, BASE_BAUD, 0x3228, 3, MCA_COM_FLAGS }, \ - { 0, BASE_BAUD, 0x4220, 3, MCA_COM_FLAGS }, \ - { 0, BASE_BAUD, 0x4228, 3, MCA_COM_FLAGS }, \ - { 0, BASE_BAUD, 0x5220, 3, MCA_COM_FLAGS }, \ - { 0, BASE_BAUD, 0x5228, 3, MCA_COM_FLAGS }, -#else -#define MCA_SERIAL_PORT_DFNS -#endif - -#define SERIAL_PORT_DFNS \ - STD_SERIAL_PORT_DEFNS \ - EXTRA_SERIAL_PORT_DEFNS \ - HUB6_SERIAL_PORT_DFNS \ - MCA_SERIAL_PORT_DFNS - -- 2.39.5