The unlock_addr rework in kernel 2.6.25 breaks 16-bit SST chips. SST
39LF160 and SST 39VF1601 are both 16-bit only chip (do not have BYTE#
pin) and new uaddr value is not correct for them. Add
MTD_UADDR_0xAAAA_0x5555 for those chips. Tested with SST 39VF1601
chip.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
[MTD][MTDPART] Seperate main loop from per-partition code in add_mtd_partition
add_mtd_partition was a 150+ line monster consisting mostly of a single
loop. Seperate the loop from most of the body. Now it should be
obvious which variables are carried around from iteration to iteration.
Signed-off-by: Jörn Engel <joern@logfs.org> Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
[MTD] physmap: resume already suspended chips on failure to suspend
A nice side effect of this patch is that the return value of
physmap_flash_suspend in the error path is the value of the first failing
suspend callback and not the bitwise OR of all of them.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Existing CFI driver has problems with excessive writes during erase.
If CFI driver does many writes during one erase cycle we may face the
messages with -ETIMEO error on erase operation. It may cause the
following data corruption and kernel panics.
The reason of the issue is related to specifics of suspend operation:
if we write to flash during erase, suspend operation will cost some time
to erase procedure (for P30 it could be significant). In current version of
cfi driver the problem of many suspends is partially workarounded by adding
some time reserv to any operation (8xerase_time) but if we have many writes
during one erase the problem appears.
This patch detects the suspend and resets timer if suspend occured. It
has been well verified on different chips. No problems were found.
Could you please include the patch as it is simple and fixes bad issue.
Signed-off-by: Alexey Korolev <akorolev@infradead.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Anton Vorontsov [Mon, 14 Jul 2008 15:20:37 +0000 (19:20 +0400)]
[MTD] [NAND] fsl_elbc_nand: fix section mismatch with CONFIG_MTD_OF_PARTS=y
With CONFIG_MTD_OF_PARTS=y I'm getting this new section mismatch in reference
from the function fsl_elbc_chip_probe() to the function
.devinit.text:of_mtd_parse_partitions()
This patch fixes the mismatch by providing __devinit annotation to the
fsl_elbc_chip_probe() function.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Acked-By: Scott Wood <scottwood@freescale.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If the the background thread is disabled for debugging purposes,
start it anyway, because otherwise we see tonns of kernel debugging
complaints like this:
If bit-flips happen often, UBI prints to many messages. Lessen
the amount by only printing the messages when the PEB has been
scrubbed. Also, print torturing messages.
Artem Bityutskiy [Mon, 16 Jun 2008 10:35:23 +0000 (13:35 +0300)]
UBI: fix LEB locking
leb_read_unlock() may be called simultaniously by several tasks.
The would race at the following code:
up_read(&le->mutex);
if (free)
kfree(le);
And it is possible that one task frees 'le' before the other tasks
do 'up_read()'. Fix this by doing up_read and free inside the
'ubi->ltree' lock. Below it the oops we had because of this:
BUG: spinlock bad magic on CPU#0, integck/7504
BUG: unable to handle kernel paging request at 6b6b6c4f
IP: [<c0211221>] spin_bug+0x5c/0xdb
*pde = 00000000 Oops: 0000 [#1] PREEMPT SMP Modules linked in: ubifs ubi nandsim nand nand_ids nand_ecc video output
Normally UBI volumes are freed in the release function of
the struct device object. However, on error path they may
have to be freed before the struct device objects have been
initialized.
ubi_free_volume() function sets ubi->volumes[] to NULL, so
ubi_eba_close() is useless, it does not free what has to be freed.
So zap it and free vol->eba_tbl at the volume release function.
Pointed-out-by: Adrian Hunter <ext-adrian.hunter@nokia.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Merge branch 'sched/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: hrtick_enabled() should use cpu_active()
sched, x86: clean up hrtick implementation
sched: fix build error, provide partition_sched_domains() unconditionally
sched: fix warning in inc_rt_tasks() to not declare variable 'rq' if it's not needed
cpu hotplug: Make cpu_active_map synchronization dependency clear
cpu hotplug, sched: Introduce cpu_active_map and redo sched domain managment (take 2)
sched: rework of "prioritize non-migratable tasks over migratable ones"
sched: reduce stack size in isolated_cpu_setup()
Revert parts of "ftrace: do not trace scheduler functions"
Fixed up conflicts in include/asm-x86/thread_info.h (due to the
TIF_SINGLESTEP unification vs TIF_HRTICK_RESCHED removal) and
kernel/sched_fair.c (due to cpu_active_map vs for_each_cpu_mask_nr()
introduction).
Merge branch 'cpus4096-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'cpus4096-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (31 commits)
NR_CPUS: Replace NR_CPUS in speedstep-centrino.c
cpumask: Provide a generic set of CPUMASK_ALLOC macros, FIXUP
NR_CPUS: Replace NR_CPUS in cpufreq userspace routines
NR_CPUS: Replace per_cpu(..., smp_processor_id()) with __get_cpu_var
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genapic_flat_64.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genx2apic_uv_x.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/proc.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/mcheck/mce_64.c
cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c, fix
cpumask: Use optimized CPUMASK_ALLOC macros in the centrino_target
cpumask: Provide a generic set of CPUMASK_ALLOC macros
cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c
cpumask: Optimize cpumask_of_cpu in kernel/time/tick-common.c
cpumask: Optimize cpumask_of_cpu in drivers/misc/sgi-xp/xpc_main.c
cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/ldt.c
cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/io_apic_64.c
cpumask: Replace cpumask_of_cpu with cpumask_of_cpu_ptr
Revert "cpumask: introduce new APIs"
cpumask: make for_each_cpu_mask a bit smaller
net: Pass reference to cpumask variable in net/sunrpc/svc.c
...
Fix up trivial conflicts in drivers/cpufreq/cpufreq.c manually
Merge branch 'core/softlockup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core/softlockup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
softlockup: fix invalid proc_handler for softlockup_panic
softlockup: fix watchdog task wakeup frequency
softlockup: fix watchdog task wakeup frequency
softlockup: show irqtrace
softlockup: print a module list on being stuck
softlockup: fix NMI hangs due to lock race - 2.6.26-rc regression
softlockup: fix false positives on nohz if CPU is 100% idle for more than 60 seconds
softlockup: fix softlockup_thresh fix
softlockup: fix softlockup_thresh unaligned access and disable detection at runtime
softlockup: allow panic on lockup
Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (85 commits)
[ARM] pxa: add base support for PXA930 Handheld Platform (aka SAAR)
[ARM] pxa: add base support for PXA930 Evaluation Board (aka TavorEVB)
[ARM] pxa: add base support for PXA930 (aka Tavor-P)
[ARM] Update mach-types
[ARM] pxa: make littleton to use the new smc91x platform data
[ARM] pxa: make zylonite to use the new smc91x platform data
[ARM] pxa: make mainstone to use the new smc91x platform data
[ARM] pxa: make lubbock to use new smc91x platform data
[NET] smc91x: prepare SMC_USE_PXA_DMA to be specified in platform data
[NET] smc91x: prepare for SMC_IO_SHIFT to be a platform configurable variable
[NET] smc91x: add SMC91X_NOWAIT flag to platform data
[NET] smc91x: favor the use of SMC91X_USE_* instead of SMC_CAN_USE_*
[NET] smc91x: remove "irq_flags" from "struct smc91x_platdata"
[ARM] 5146/1: pxa2xx: convert all boards to call pxa2xx_transceiver_mode helper
Support for LCD on e740 e750 e400 and e800 e-series PDAs
E-series UDC support
PXA UDC - allow use of inverted GPIO for pullup
Add e350 support
Fix broken e-series build
E-series GPIO / IRQ definitions.
...
Roland McGrath [Tue, 24 Jun 2008 11:16:52 +0000 (04:16 -0700)]
i386 syscall audit fast-path
This adds fast paths for 32-bit syscall entry and exit when
TIF_SYSCALL_AUDIT is set, but no other kind of syscall tracing.
These paths does not need to save and restore all registers as
the general case of tracing does. Avoiding the iret return path
when syscall audit is enabled helps performance a lot.
Roland McGrath [Tue, 24 Jun 2008 08:13:31 +0000 (01:13 -0700)]
x86_64 ia32 syscall audit fast-path
This adds fast paths for 32-bit syscall entry and exit when
TIF_SYSCALL_AUDIT is set, but no other kind of syscall tracing.
These paths does not need to save and restore all registers as
the general case of tracing does. Avoiding the iret return path
when syscall audit is enabled helps performance a lot.
Roland McGrath [Mon, 23 Jun 2008 22:37:04 +0000 (15:37 -0700)]
x86_64 syscall audit fast-path
This adds a fast path for 64-bit syscall entry and exit when
TIF_SYSCALL_AUDIT is set, but no other kind of syscall tracing.
This path does not need to save and restore all registers as
the general case of tracing does. Avoiding the iret return path
when syscall audit is enabled helps performance a lot.
Roland McGrath [Tue, 24 Jun 2008 03:41:12 +0000 (20:41 -0700)]
x86_64: remove bogus optimization in sysret_signal
This short-circuit path in sysret_signal looks wrong to me.
AFAICT, in practice the branch is never taken--and if it were,
it would go wrong. To wit, try loading a module whose init
function does set_thread_flag(TIF_IRET), and see insmod crash
(presumably with a wrong user stack pointer).
This is because the FIXUP_TOP_OF_STACK work hasn't been done yet
when we jump around the call to ptregscall_common and get to
int_with_check--where it expects the user RSP,SS,CS and EFLAGS to
have been stored by FIXUP_TOP_OF_STACK.
I don't think it's normally possible to get to sysret_signal with no
_TIF_DO_NOTIFY_MASK bits set anyway, so these two instructions are
already superfluous. If it ever did happen, it is harmless to call
do_notify_resume with nothing for it to do.
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
sdhci: highmem capable PIO routines
sg: reimplement sg mapping iterator
mmc_test: print message when attaching to card
mmc: Remove Russell as primecell mci maintainer
mmc_block: bounce buffer highmem support
sdhci: fix bad warning from commit c8b3e02
sdhci: add warnings for bad buffers in ADMA path
mmc_test: test oversized sg lists
mmc_test: highmem tests
s3cmci: ensure host stopped on machine shutdown
au1xmmc: suspend/resume implementation
s3cmci: fixes for section mismatch warnings
pxamci: trivial fix of DMA alignment register bit clearing
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (24 commits)
I/OAT: I/OAT version 3.0 support
I/OAT: tcp_dma_copybreak default value dependent on I/OAT version
I/OAT: Add watchdog/reset functionality to ioatdma
iop_adma: cleanup iop_chan_xor_slot_count
iop_adma: document how to calculate the minimum descriptor pool size
iop_adma: directly reclaim descriptors on allocation failure
async_tx: make async_tx_test_ack a boolean routine
async_tx: remove depend_tx from async_tx_sync_epilog
async_tx: export async_tx_quiesce
async_tx: fix handling of the "out of descriptor" condition in async_xor
async_tx: ensure the xor destination buffer remains dma-mapped
async_tx: list_for_each_entry_rcu() cleanup
dmaengine: Driver for the Synopsys DesignWare DMA controller
dmaengine: Add slave DMA interface
dmaengine: add DMA_COMPL_SKIP_{SRC,DEST}_UNMAP flags to control dma unmap
dmaengine: Add dma_client parameter to device_alloc_chan_resources
dmatest: Simple DMA memcpy test client
dmaengine: DMA engine driver for Marvell XOR engine
iop-adma: fix platform driver hotplug/coldplug
dmaengine: track the number of clients using a channel
...
Fixed up conflict in drivers/dca/dca-sysfs.c manually
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (60 commits)
ide: small whitespace fixes
ide: ide-cd_ioctl.c fix sparse integer as NULL pointer warnings
ide: ide-cd.c fix sparse endianness warnings
ide-cd: convert to using the new atapi_flags
ide: remove unused PC_FLAG_DRQ_INTERRUPT
ide-scsi: convert to using the new atapi_flags
ide-tape: convert to using the new atapi_flags
ide-floppy: convert to using the new atapi_flags (take 2)
ide: add per-device flags
ide: use rq->cmd instead of pc->c in atapi common code
ide-scsi: pass packet command in rq->cmd
ide-tape: pass packet command in rq->cmd
ide-tape: make room for packet command ids in rq->cmd
ide-floppy: pass packet command in rq->cmd
ide: remove pc->callback member from ide_atapi_pc
ide-scsi: use drive->pc_callback instead of pc->callback
ide-tape: use drive->pc_callback instead of pc->callback
ide-floppy: use drive->pc_callback instead of pc->callback
ide: push pc callback pointer into the ide_drive_t structure
drivers/ide/ide-tape.c: remove double kfree
...
Harvey Harrison [Wed, 23 Jul 2008 17:56:02 +0000 (19:56 +0200)]
ide: ide-cd_ioctl.c fix sparse integer as NULL pointer warnings
The function ide_cd_queue_pc should be checked as the bufflen arg is
dereferenced and lots of callers are passing in NULL.
drivers/ide/ide-cd_ioctl.c:124:46: warning: Using plain integer as NULL pointer
drivers/ide/ide-cd_ioctl.c:149:47: warning: Using plain integer as NULL pointer
drivers/ide/ide-cd_ioctl.c:231:46: warning: Using plain integer as NULL pointer
drivers/ide/ide-cd_ioctl.c:374:46: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org> Acked-by: Borislav Petkov <petkovbb@gmail.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make a redundant copy of the packet command bits into rq->cmd.
Later, after all drivers have been converted, it'll be
switched to use that in the common code instead of pc->c.
There should be no functionality change resulting from this patch.
Make a redundant copy of the packet command bits into rq->cmd. Later, after
all drivers have been converted, it'll be switched to use that in the
common code instead of pc->c. While at it, simplify ide_tape_create_rw_cmd.
There should be no functionality change resulting from this patch.
Make a redundant copy of the packet command bits into rq->cmd.
Later, after all drivers have been converted, it'll be
switched to use that in the common code instead of pc->c.
There should be no functionality change resulting from this patch.
ide-tape: use drive->pc_callback instead of pc->callback
The if-else block in the IRQ handler is only temporary so that bisect searches
don't break and it'll be removed after converting the remainder of the drivers.
There should be no functionality change resulting from this patch.
ide-floppy: use drive->pc_callback instead of pc->callback
It is important that drive->pc_callback is set prior to enabling IRQs on the
device since this is called from the IRQ handler. Otherwise it hurts as I learnt
the hard way from the several "Kernel panic - not synching: Fatal exception in
interrupt" during the weekend :).
The if-else block in the IRQ handler is only temporary so that bisect searches
don't break and it'll be removed after converting the remainder of the drivers.
There should be no functionality change resulting from this patch.
ide: push pc callback pointer into the ide_drive_t structure
Refrain from carrying the callback ptr with every packet command since the
callback function is only one anyways. ide_drive_t is probably not the most
suitable place for it right now but is the more sane solution. Besides, these
structs are going to be reorganized anyways during the generic ide rewrite.
Add ide_host_add() helper which does ide_host_alloc()+ide_host_register(),
then convert ide_setup_pci_device[s](), ide_legacy_device_add() and some
host drivers to use it.
While at it:
* Fix ide_setup_pci_device[s](), ide_arm.c, gayle.c, ide-4drives.c,
macide.c, q40ide.c, cmd640.c and cs5520.c to return correct error value.
* -ENOENT -> -ENOMEM in rapide.c, ide-h8300.c, ide-generic.c, au1xxx-ide.c
and pmac.c
* -ENODEV -> -ENOMEM in palm_bk3710.c, ide_platform.c and delkin_cb.c
* Reserve memory resources for all IDE ports at once by moving
request_mem_region() out of 'for ()' loop and always defining
GAYLE_IDEREG_SIZE to 0x2000.
* Keep memory resources even if no free IDE slots can be found
(this driver is unloadable currently).
ide: filter out "default" transfer mode values in set_xfer_rate()
* Filter out "default" transfer mode values (0x00 - default PIO mode,
0x01 - default PIO mode w/ IORDY disabled) in write handler for obsoleted
/proc/ide/hd?/settings:current_speed setting.
Allowing "default" transfer mode values is a dangerous thing to do as
we don't support programming controller to the "default" transfer mode
and devices often use different values for the default and maximum PIO
mode (i.e. PIO2 default and PIO4 maximum) so the controller will stay
programmed for higher PIO mode while device will use the lower PIO mode.
There is no functionality loss as by using special IOCTLs device can
still be programmed to "default" transfer modes (it is only useful for
debugging/testing purposes anyway).
* Remove no longer needed IDE_HFLAG_ABUSE_SET_DMA_MODE host flag, it was
previously used by few host drivers to program the controller to PIO0
timings for "default" transfer mode == 0x01 (although some host drivers
would program invalid PIO timings instead).
* Cleanup ide_set_xfer_rate() and add BUG_ON().
Suggested-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Alan Cox has noticed some time ago that hpt34x is broken
(http://lkml.org/lkml/2007/7/3/257):
"No the old driver doesn't even do that. It starts up. It spuriously
adjusts some non writable PCI BAR registers, prints a message about
resources being in use already then exits."
Reported-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
projects / linux-2.6 / log