Gregory Greenman [Thu, 15 May 2008 05:53:59 +0000 (13:53 +0800)]
iwlwifi: get_hw_cmd_size
This patch introduces a new handler get_hw_cmd_size in hcmd_utils,
which should adjust the size of the command sent to the microcode
according to the current nic.
It also changes the RXON flow to make usage of this new handler.
The patch also adds iwl_rxon_cmd structure which is supperset for
5000 HW and 4965.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ron Rindjunsky [Thu, 15 May 2008 05:53:56 +0000 (13:53 +0800)]
iwlwifi: filling Tx MCS set
This patch fills the needed data about HW capabilities in matters of
possible HT Tx MCS.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ron Rindjunsky [Thu, 15 May 2008 05:53:55 +0000 (13:53 +0800)]
mac80211: separate Tx and Rx MCS when configuring HT
This patch follows the 11n spec in separation between Tx and Rx MCS
capabilities. Up until now, when configuring the HT possible set of Tx
MCS only Rx MCS were considered, assuming they are the same as the Tx MCS.
This patch fixed this by looking at low level driver Tx capabilities.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ron Rindjunsky [Thu, 15 May 2008 05:53:54 +0000 (13:53 +0800)]
iwlwifi: remove iwl4965_nic_start function
This patch moves the contant of iwl4965_nic_start to the only place it is
being used.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Harvey Harrison [Wed, 14 May 2008 23:26:20 +0000 (16:26 -0700)]
mac80211: tkip.c use struct tkip_ctx in phase 2 key mixing
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Cc: "John W. Linville" <linville@tuxdriver.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Harvey Harrison [Wed, 14 May 2008 23:26:19 +0000 (16:26 -0700)]
mac80211: tkip.c use struct tkip_ctx in phase 1 key mixing
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Cc: "John W. Linville" <linville@tuxdriver.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Harvey Harrison [Wed, 14 May 2008 23:26:19 +0000 (16:26 -0700)]
mac80211: add a struct to hold tkip context
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Cc: "John W. Linville" <linville@tuxdriver.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Harvey Harrison [Wed, 14 May 2008 23:26:18 +0000 (16:26 -0700)]
mac80211: add const, remove unused function, make one function static
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Cc: "John W. Linville" <linville@tuxdriver.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Harvey Harrison [Wed, 14 May 2008 23:26:17 +0000 (16:26 -0700)]
mac80211: introduce struct michael_mic_ctx and static helpers
Replace the existing macro with a static function, significantly shrinks the
size of the produced object file.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Cc: "John W. Linville" <linville@tuxdriver.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Harvey Harrison [Wed, 14 May 2008 23:26:16 +0000 (16:26 -0700)]
mac80211: michael.c use kernel-provided infrastructure
Replace private implementation of bit rotation and unaligned access helpers
with kernel-provided implementation.
Fold xswap helper in its one usage in the michael_block macro.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Cc: "John W. Linville" <linville@tuxdriver.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Holger Schurig [Wed, 14 May 2008 14:30:28 +0000 (16:30 +0200)]
libertas: reduce command retry time
[PATCH, take 2] libertas: reduce command retry time
In the normal case, an unsuccessful command would be retried for 10*5 seconds,
or 10*10 seconds in the worst case. This patch reduces this to 3*3 seconds,
or 3*10 seconds in the worst case.
I also reduced the time it takes to start a new command downloaded.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Emelyanov [Wed, 7 May 2008 15:51:51 +0000 (19:51 +0400)]
mac80211: Fix sleeping allocation under lock in mesh_path_node_copy.
The mesh_path_node_copy() can be called like this:
mesh_path_add
`- write_lock(&pathtbl_resize_lock); /* ! */
`- mesh_table_grow
`- ->copy_node
`- mesh_path_node_copy
thus, the GFP_KERNEL is not suitable here.
The acceptable fix, I suppose, is make this allocation GPF_ATOMIC -
the mpath_node being allocated is 4 pointers, i.e. this allocation
is small enough to survive even under a moderate memory pressure.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Emelyanov [Wed, 7 May 2008 15:47:01 +0000 (19:47 +0400)]
mac80211: Prepare mesh_table_grow to failing copy_node callback.
The mesh_path_node_copy() performs kmalloc() and thus - may fail
(well, it does not now, but I'm fixing this right now). Its caller -
the mesh_table_grow() - isn't prepared for such a trick yet.
This preparation is just flush the new hash and make copy_node()
return an int value.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Emelyanov [Wed, 7 May 2008 15:44:20 +0000 (19:44 +0400)]
mac80211: Fix one more call to synchronize_rcu in atomic context.
(This set applies OK without the previous one of 4 patches,
but with some fuzz in the 7th one)
The mesh_path_node_free() does so under hashwlock.
But, this one is called
1. from mesh_path_add() after an old hash is hidden and
synchronize_rcu() is calld
2. mesh_pathtbl_unregister(), when the module is being
unloaded and no devices exist to mess with this hash.
So, it seems to me, that simply removing the call is OK.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Javier Cardona [Tue, 20 May 2008 22:18:49 +0000 (15:18 -0700)]
libertas: sysfs interface for accessing default mesh channel
This will create the following entry:
/sys/class/net/mshX
-- boot_options
| |-- ...
| `-- channel
...
... which I overlooked on my previous patch.
Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Javier Cardona [Sun, 18 May 2008 04:01:24 +0000 (21:01 -0700)]
libertas: sysfs interface for accessing non-volatile configuration
This will create the following sysfs directories:
/sys/class/net/mshX
...
|-- boot_options
| |-- bootflag
| `-- boottime
...
|-- mesh_ie
| |-- capability
| |-- mesh_id
| |-- metric_id
| `-- protocol_id
Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Javier Cardona [Sat, 17 May 2008 07:55:10 +0000 (00:55 -0700)]
libertas: Extend MESH_CONFIG command to access non-volatile configuration
This patch is based on a patch from Shailendra Govardhan and Brian Cavagnolo.
It extends the MESH_CONFIG command to configure non-volatile parameters on
libertas devices that support them (e.g. OLPC Active Antenna).
This patch only implements the driver/firmware interface.
See http://dev.laptop.org/ticket/6823 for minimal testing results and known
issues.
Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Woodhouse [Tue, 20 May 2008 12:32:45 +0000 (13:32 +0100)]
libertas: fix multicast filtering on eth and msh interfaces
We weren't properly handling multicast on the mesh interface. Fix that,
which involves setting up the hardware to use the union of dev->mc_list
for both eth%d and msh%d devices.
This means we can't do it directly from ->set_multicast_list() because
we'd need to lock the other device to read its list, and we can't do
that because it might deadlock. So punt the actual work to keventd.
Also, invoke the same when taking an interface down; for some reason the
core calls ->set_multicast_list while IFF_UP is still set in dev->flags
when we're taking it down, so its addresses don't get removed then.
We also convert MAC_MULTICAST_ADR to a direct command while we're at it,
removing one more entry from the big switch statement in the deprecated
lbs_prepare_and_send_command() function.
Signed-off-by: David Woodhouse <dwmw2@infradead.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Woodhouse [Tue, 20 May 2008 10:47:16 +0000 (11:47 +0100)]
libertas: Increase priority of 'unknown command' warnings
Using the deprecated lbs_prepare_and_send_command() function for a
command which it doesn't understand is an error; complain loudly about
it even when we're not debugging.
The mesh stats bug, where we converted MESH_ACCESS to a direct command
but accidentally missed one user which was still trying to do it through
lbs_prepare_and_send_command(), would have been caught a lot quicker if
we'd done this sooner. Such bugs aren't entirely unlikely in future too,
as we convert more code to stop using this function.
Signed-off-by: David Woodhouse <dwmw2@infradead.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sat, 10 May 2008 11:46:03 +0000 (13:46 +0200)]
rt2x00: Merge RX and TX entry private data
With the pending removal of the tx_control structure
we can merge the RX and TX entry private data structure
in advance. This will temporarily increase the required
memory for the queue, but that overhead will only be limited.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
the rxdesc structure is properly memsetted before passed to
the driver. This means we don't have to reinitialize the flags
and dev_flags fields in the drivers again.
This will prevent problems when the rxdone handler is adding
flags in a earlier status and will make the code look nicer
when we are adding more read attributes in the rxdone handler
in the driver.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sat, 10 May 2008 11:46:13 +0000 (13:46 +0200)]
rt2x00: Split rt2x00lib_write_tx_desc()
Split rt2x00lib_write_tx_desc() up into a TX descriptor initializor
and TX descriptor writer.
This split is required to properly allow mac80211 to move its
tx_control structure into the skb->cb array.
The rt2x00queue_create_tx_descriptor() function will read all tx control
information and convert it into a rt2x00 TX descriptor information structure.
After that function is complete, we have all information we needed from the
tx control structure and are free to start writing into the skb->cb array
for our own purposes.
rt2x00queue_write_tx_descriptor() will be in charge of really sending
the TX descriptor to the hardware and kicking the TX queue.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00: Only initialize the minimum needed fields of PCI TX descriptors.
In preparation of replacing the statically allocated data DMA buffers with DMA-mapped
skb's we need to change the TXD handling of the PCI drivers, by moving the programming
of the buffer address fields to the actual TXD writing at TX time, instead of at start-up
time.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sat, 10 May 2008 11:43:38 +0000 (13:43 +0200)]
rt2x00: Preserve descriptor information after memmove()
Due to usage of memmove() in rt2x00usb the descriptor can become
corrupted because it is being overwritten by the data part.
Overall having the descriptor in front of the frame is a bad idea,
we can however use the skb->cb array for this task, since that
contains more then enough room to hold the entire descriptor and
preserve the information long enough.
After this we can also cleanup the alignment code a bit to make it
work a bit more flexible to allow for all kinds of odd header lengths.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00: Fix queue related oops in case of deselected mac80211 multi-queue feature.
With the integration of the mac80211 multiqueue patches it has become possible that the
mac80211 layer modifies the number of TX queues that is stored inside the ieee80211_hw
structure, especially when multi-queue is not selected.
The rt2x00 drivers are not well suited to handle that situation, as they allocate the
queue structures before mac80211 has modified the number of queues it is going to use,
and also expect the number of allocated queues to match the hardware implementation.
Hence, ensure that rt2x00 maintains by itself the number of queues that the hardware
supports, and, at the same time, making is not dependent on the preservation of contents
inside a mac80211 structure.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sat, 10 May 2008 11:42:31 +0000 (13:42 +0200)]
rt2x00: Remove ieee80211_tx_control argument from write_tx_desc()
Move the last remaining information details read from ieee80211_tx_control
in the drivers to the txentry_desc structure. After this we can
remove ieee80211_tx_control from the argument list for the callback function,
which makes it easier when the control information is moved into skb->cb
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sat, 10 May 2008 11:42:06 +0000 (13:42 +0200)]
rt2x00: Fix TX status reporting
The tx_status enumeration was broken since the introduction
of rt61pci. That driver uses different values to report the
status of the tx action.
This would lead to frames that were reported as success but
actually failed to be send out, or frames that were neither
successfull or failure which were reported as failure.
Fix this by change the TX status reporting and more explicitely
check for failure or success. Note that a third possibility is
added "unknown". Not all hardware (USB) can report the actual
TX status, for rt61pci some frames will receive this status
because the TXdone handler is never called for those frames.
This unknown will now be handled as neither success or failure,
so we no longer increment the failure counter while this conclusion
could not be determined from the real status of the frame.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sat, 10 May 2008 11:41:32 +0000 (13:41 +0200)]
rt2x00: trim skb_frame_desc to 32 bytes
Remove frame_type from skb_frame_desc and pass it
as argument to rt2x00debug_dump_frame().
Change data_len and desc_len to unsigned short
to save another 4 bytes in skb_frame_desc. Note that
this was the only location where the data_len and
desc_len was not yet treated as unsigned short.
This trim is required to help mac80211 with adding
the TX control and TX status informtation into the
skb->cb structure. When that happens, drivers will
have approximately 40 bytes left to use freely.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allan Stephens [Mon, 19 May 2008 20:30:13 +0000 (13:30 -0700)]
tipc: Cosmetic cleanup of topology service code
This patch contains a set of cosmetic changes to TIPC's network
topology service subsystem, including:
- updates to comments (including copyright dates)
- re-ordering structure fields to group them more logically
- removal of optional debugging code that is no longer required
- minor changes to whitespace to conform to Linux coding conventions
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Mon, 19 May 2008 20:29:47 +0000 (13:29 -0700)]
tipc: Consolidate subscriber & subscriber port references
This patch modifies TIPC's network topology service so that it
only requires a single reference table entry per subscriber
connection, rather than two. This is achieved by letting the
reference to the server port communicating with the subscriber
act as the reference to the subscriber object itself. (Since
the subscriber cannot exist without its port, and vice versa,
this dual role for the reference is perfectly natural.) This
consolidation reduces the size of the reference table by 50%
in the default configuration.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Mon, 19 May 2008 20:29:06 +0000 (13:29 -0700)]
tipc: Fix bug in topology server byte swapping routine
This patch fixes TIPC's topology server so that it does byte swapping
correctly when endianness conversion is required. (Note: This bug only
impacted an application if it issues a subscription request to a
topology server on another node, rather than the server on it's own
node; since the topology server is normally not accessible by off-node
applications, most TIPC applications were not impacted by the bug.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Mon, 19 May 2008 20:28:32 +0000 (13:28 -0700)]
tipc: Add support for customized subscription endianness
This patch enables TIPC's topology server code to do customized
endianness conversions on a per-subscription basis. (This
capability is needed to support the upcoming consolidation of
subscriber and subscription object references.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Mon, 19 May 2008 20:27:31 +0000 (13:27 -0700)]
tipc: Add support for customized subscription overlap handling
This patch enables TIPC's topology server code to do customized
overlap detection handling on a per-subscription basis. (This
capability is needed to support the upcoming introduction of
multi-cluster TIPC networks.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Li [Sat, 17 May 2008 05:20:27 +0000 (22:20 -0700)]
bnx2: Pre-initialize struct cpu_reg.
Instead of assigning values for the struct cpu_reg's at runtime,
we already know these values at compile time. Therefore, we can use
designated initializers, to initialize these structures and not have
to incur this assignment cost at run-time.
Signed-off-by: Benjamin Li <benli@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Li [Sat, 17 May 2008 05:18:57 +0000 (22:18 -0700)]
bnx2: Remove the rx_offset field from the bnx2 structure.
The rx_offset field is set to a constant value and initialized
only once. By replacing all references to the rx_offset field,
we can eliminate rx_offset from the bnx2 structure. This will
save 4 bytes for every bnx2 instance.
[Added parentheses to the definition of BNX2_RX_OFFSET, as noted
by Ben Hutchings.]
Signed-off-by: Benjamin Li <benli@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sat, 17 May 2008 05:17:45 +0000 (22:17 -0700)]
bnx2: Allow phy reset to be skipped during chip reset.
Andy Gospodarek <andy@greyhouse.net> found that netconsole would
panic when resetting bnx2 devices.
>From Andy:
"The issue is the bnx2_set_link in bnx2_init_nic will print a link-status
message before we are fully initialized and ready to start polling.
Polling is currently disabled in this state, but since the
__LINK_STATE_RX_SCHED is overloaded to not only try and disable polling
but also to make the system aware there is something waiting to be
polled, we really have to fix this in drivers.
The problematic call is the one to netif_rx_complete as it tries to
remove an entry from the poll_list when there isn't one."
While this netconsole problem should be fixed separately, we really
should not reset the PHY when changing ring sizes, MTU, or other
similar settings. The PHY reset causes several seconds of unnecessary
link disruptions.
Signed-off-by: Michael Chan <mchan@broadcom.com> Acked-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Marcin Slusarz [Thu, 15 May 2008 06:30:06 +0000 (23:30 -0700)]
isdn/capi: Return proper errnos on module init.
cdebug_init() is called from kcapi_init() which is module
initialization function, so it must return negative values on errors.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Acked-by: Karsten Keil <kkeil@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Alan Cox [Thu, 15 May 2008 06:28:47 +0000 (23:28 -0700)]
iphase: Fix 64bit warning.
Time is unsigned long (except when you are in a hurry) so we need to
store rx_tmp_jif in the right sized object.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Morton [Thu, 15 May 2008 06:27:18 +0000 (23:27 -0700)]
hysdn: No longer broken on SMP.
With the cli/sti code sorted out we think this driver is OK for use on
SMP systems.
Acked-by: Mark Asselstine <mark.asselstine@windriver.com> Acked-by: Karsten Keil <kkeil@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Mark Asselstine [Thu, 15 May 2008 06:25:33 +0000 (23:25 -0700)]
hysdn: Remove cli()/sti() calls.
The use of cli()/sti() within the do/while was a way to ensure
interrupts were only disabled for short periods of time while the bulk
of the time interrupts were free to occur. The use of the spin lock
has eliminated the need to play with interrupts in this way while
still allowing for IO to be protected.
The remaining 3 sti() calls seem unneeded now that at no other point
in the driver is there a call to cli().
Signed-off-by: Mark Asselstine <mark.asselstine@windriver.com> Acked-by: Karsten Keil <kkeil@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Frysinger [Thu, 15 May 2008 06:24:09 +0000 (23:24 -0700)]
atm: Cleanup atm_tcp.h and atm.h for userspace.
The atm_tcp.h uses types from linux/atm.h, but does not include it.
It should also use the standard __u## types from linux/types.h rather
than the uint##_t types since the former can be found with the kernel
already.
Same goes for linux/atm.h. The linux/socket.h include there also gets
dropped as atm.h does not actually use anything from socket.h.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible that the entry in sysfs already exists, one case of this is
when a network device is renamed to bonding_masters. Anyway, in this case
the proper error path is for device_rename to return an error code, not to
generate bogus backtrace and errors.
Also, to avoid possible races, the create link should be done before the
remove link. This makes a device rename atomic operation like other renames.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 15 May 2008 02:30:13 +0000 (19:30 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs
* 'for-linus' of ssh://master.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
9p: fix error path during early mount
9p: make cryptic unknown error from server less scary
9p: fix flags length in net
9p: Correct fidpool creation failure in p9_client_create
9p: use struct mutex instead of struct semaphore
9p: propagate parse_option changes to client and transports
fs/9p/v9fs.c (v9fs_parse_options): Handle kstrdup and match_strdup failure.
9p: Documentation updates
add match_strlcpy() us it to make v9fs make uname and remotename parsing more robust
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Use a TS_RESTORE_SIGMASK
lmb: Make lmb debugging more useful.
lmb: Fix inconsistent alignment of size argument.
sparc: Fix mremap address range validation.
Andrew Morton [Wed, 14 May 2008 23:05:59 +0000 (16:05 -0700)]
net/irda/irnet/irnet_irda.c needs unaligned.h
net/irda/irnet/irnet_irda.c: In function 'irnet_discovery_indication':
net/irda/irnet/irnet_irda.c:1676: error: implicit declaration of function 'get_unaligned'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Neil Brown [Wed, 14 May 2008 23:05:54 +0000 (16:05 -0700)]
Remove blkdev warning triggered by using md
As setting and clearing queue flags now requires that we hold a spinlock
on the queue, and as blk_queue_stack_limits is called without that lock,
get the lock inside blk_queue_stack_limits.
For blk_queue_stack_limits to be able to find the right lock, each md
personality needs to set q->queue_lock to point to the appropriate lock.
Those personalities which didn't previously use a spin_lock, us
q->__queue_lock. So always initialise that lock when allocated.
With this in place, setting/clearing of the QUEUE_FLAG_PLUGGED bit will no
longer cause warnings as it will be clear that the proper lock is held.
Thanks to Dan Williams for review and fixing the silly bugs.
Signed-off-by: NeilBrown <neilb@suse.de> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Jens Axboe <jens.axboe@oracle.com> Cc: Alistair John Strachan <alistair@devzero.co.uk> Cc: Nick Piggin <npiggin@suse.de> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Cc: Jacek Luczak <difrost.kernel@gmail.com> Cc: Prakash Punnoor <prakash@punnoor.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Wed, 14 May 2008 23:05:53 +0000 (16:05 -0700)]
char: select fw_loader by moxa
Select FW_LOADER since moxa needs it, otherwise we face link problems such
as:
drivers/built-in.o: In function
moxa_pci_probe':moxa.c:(.devinit.text+0x76d8): undefined reference to
request_firmware'
:moxa.c:(.devinit.text+0x7e6e): undefined reference to release_firmware'
make: *** [.tmp_vmlinux1] Error 1
Reported-by: Philippe Roussel <p.o.roussel@free.fr> Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Trying to online a new memory section that was added via memory hotplug
sometimes results in crashes when the new pages are added via __free_page.
Reason for that is that the pageblock bitmap isn't initialized and hence
contains random stuff. That means that get_pageblock_migratetype()
returns also random stuff and therefore
in __free_one_page() tries to do a list_add to something that isn't even
necessarily a list.
This happens since 86051ca5eaf5e560113ec7673462804c54284456 ("mm: fix
usemap initialization") which makes sure that the pageblock bitmap gets
only initialized for pages present in a zone. Unfortunately for hot-added
memory the zones "grow" after the memmap and the pageblock memmap have
been initialized. Which means that the new pages have an unitialized
bitmap. To solve this the calls to grow_zone_span() and grow_pgdat_span()
are moved to __add_zone() just before the initialization happens.
The patch also moves the two functions since __add_zone() is the only
caller and I didn't want to add a forward declaration.
Venki Pallipadi [Wed, 14 May 2008 23:05:51 +0000 (16:05 -0700)]
mprotect: prevent alteration of the PAT bits
There is a defect in mprotect, which lets the user change the page cache
type bits by-passing the kernel reserve_memtype and free_memtype
wrappers. Fix the problem by not letting mprotect change the PAT bits.
Eric Dumazet [Wed, 14 May 2008 23:05:51 +0000 (16:05 -0700)]
per_cpu: fix DEFINE_PER_CPU_SHARED_ALIGNED for modules
Current module loader lookups ".data.percpu" ELF section to perform
per_cpu relocation. But DEFINE_PER_CPU_SHARED_ALIGNED() uses another
section (".data.percpu.shared_aligned"), currently only handled in
vmlinux.lds, not by module loader.
To correct this problem, instead of adding logic into module loader, or
using at build time a module.lds file for all arches to group
".data.percpu.shared_aligned" into ".data.percpu", just use ".data.percpu"
for modules.
Alignment requirements are correctly handled by ld and module loader.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Fenghua Yu <fenghua.yu@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Geoff Levand [Wed, 14 May 2008 23:05:50 +0000 (16:05 -0700)]
memory_hotplug: check for walk_memory_resource() failure in online_pages()
Add a check to online_pages() to test for failure of
walk_memory_resource(). This fixes a condition where a failure
of walk_memory_resource() can lead to online_pages() returning
success without the requested pages being onlined.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com> Cc: Yasunori Goto <y-goto@jp.fujitsu.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Dave Hansen <haveblue@us.ibm.com> Cc: Keith Mannthey <kmannth@us.ibm.com> Cc: Christoph Lameter <clameter@sgi.com> Cc: Paul Jackson <pj@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tiger Yang [Wed, 14 May 2008 23:05:47 +0000 (16:05 -0700)]
ext3/4: fix uninitialized bs in ext3/4_xattr_set_handle()
This fix the uninitialized bs when we try to replace a xattr entry in
ibody with the new value which require more than free space.
This situation only happens we format ext3/4 with inode size more than 128 and
we have put xattr entries both in ibody and block. The consequences about
this bug is we will lost the xattr block which pointed by i_file_acl with all
xattr entires in it. We will alloc a new xattr block and put that large value
entry in it. The old xattr block will become orphan block.
Signed-off-by: Tiger Yang <tiger.yang@oracle.com> Cc: <linux-ext4@vger.kernel.org> Cc: Andreas Gruenbacher <agruen@suse.de> Acked-by: Andreas Dilger <adilger@sun.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Frysinger [Wed, 14 May 2008 23:05:42 +0000 (16:05 -0700)]
asm-{alpha,h8300,um,v850,xtensa}/param.h: unbreak HZ for userspace
I noticed this because alpha was broken due to the recent commit commit bdc807871d58285737d50dc6163d0feb72cb0dc2 ("avoid overflows in
kernel/time.c"). Most arches do something like this in their
asm/param.h:
A few arches though (namely alpha/h8300/um/v850/xtensa) either do no set
HZ at all for !__KERNEL__, or they set it wrongly. This should bring all
arches in line by setting up HZ for userspace.
Without this currently perl 5.10 doesn't build on alpha:
perl.c: In function 'perl_construct':
perl.c:388: error: 'CONFIG_HZ' undeclared (first use in this function)
-> http://buildd.debian.org/fetch.cgi?pkg=perl;ver=5.10.0-10;arch=alpha;stamp=1210252894
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: Jeff Dike <jdike@addtoit.com> Cc: Chris Zankel <chris@zankel.net> Cc: maximilian attems <max@stro.at> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ HZ on alpha is 1024 for historical reasons. - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mingming Cao [Wed, 14 May 2008 23:05:41 +0000 (16:05 -0700)]
jbd: need to hold j_state_lock to updates to transaction t_state to T_COMMIT
Updating the current transaction's t_state is protected by j_state_lock. We
need to do the same when updating the t_state to T_COMMIT.
Signed-off-by: Mingming Cao <cmm@us.ibm.com> Acked-by: Jan Kara <jack@ucw.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Heiko Carstens [Wed, 14 May 2008 23:05:40 +0000 (16:05 -0700)]
memory hotplug: memmap_init_zone called twice
__add_zone calls memmap_init_zone twice if memory gets attached to an empty
zone. Once via init_currently_empty_zone and once explictly right after that
call.
Looks like this is currently not a bug, however the call is superfluous and
might lead to subtle bugs if memmap_init_zone gets changed. So make sure it
is called only once.
Nate Case [Wed, 14 May 2008 23:05:39 +0000 (16:05 -0700)]
ipmi: support I/O resources in OF driver
The current OF probing assumes that the resource is IORESOURCE_MEM. This
checks for the IORESOURCE_IO flag and behaves appropriately. An I/O resource
can exist with an ipmi device node on a legacy ISA bus.
Signed-off-by: Nate Case <ncase@xes-inc.com> Signed-off-by: Corey Minyard <cminyard@mvista.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nicolas Ferre [Wed, 14 May 2008 23:05:38 +0000 (16:05 -0700)]
atmel_lcdfb: fix initialization of a pre-allocated framebuffer
Fix initialization of framebuffer not calling ioremap_writecombine() function
and not using internal SRAM for at91sam9rl.
This is a little rework of the "Don't initialize a pre-allocated framebuffer"
patch that corrects the call to ioremap_writecombine() function.
It also cuts the use of internal SRAM for at91sam9rl : it is a bit small
for a framebuffer.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Andrew Victor <linux@maxim.org.za> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm: fix fault vs invalidate race for linear mappings
Fix by reintroducing the wait_on_page_locked() after ->readpage() to make sure
the page is up-to-date before jumping back to the beginning of the function.
I've noticed this while testing nfs exporting on fuse. The patch
fixes it.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> Cc: Nick Piggin <npiggin@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rene Herman [Wed, 14 May 2008 23:05:36 +0000 (16:05 -0700)]
pnp: add ISAPnP MPU option quirks
The AD181x and AZT230 chips don't support an IRQ-less MPU401 option but
work fine without one. This adds (priority functional) IRQ-less options
for each port option to help systems with few available IRQs.
The AD1815 quirk can't use pnp_register_irq_resource() due to doubly
penalizing the IRQ. Also, while not a practical issue due to no IRQ
option being present for the dependents, this needs to add in front, not
back.
Doesn't use pnp_register_port_resource() for symetry with above.
This does not delete the AD1815 independent option even though it should
be empty after the IRQ transfer due to AD1816 coming with an empty but
still present independent option by default.
Was tested on AD1815, AD1816 and AZT2320. The ALSA snd-ad1818a driver
also support the AZT2002 ID for MPU401 but this doesn't as I was unable to
test it.
Signed-off-by: Rene Herman <rene.herman@gmail.com> Tested-by: Uwe Bugla <uwe.bugla@gmx.de> Acked-by: Uwe Bugla <uwe.bugla@gmx.de> Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Cc: Takashi Iwai <tiwai@suse.de> Cc: Len Brown <len.brown@intel.com Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rene Herman [Wed, 14 May 2008 23:05:34 +0000 (16:05 -0700)]
pnp: add pnp_build_option() to the API
The subsequent AD181x quirk patch would like this as part of the API.
pnp_register_dependent_option() adds to the same dependent chain the quirk is
walking which is fairly unclean. This enables a private option chain build
which it can then just add onto the end when done.
Signed-off-by: Rene Herman <rene.herman@gmail.com> Tested-by: Uwe Bugla <uwe.bugla@gmx.de> Acked-by: Uwe Bugla <uwe.bugla@gmx.de> Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Cc: Takashi Iwai <tiwai@suse.de> Cc: Len Brown <len.brown@intel.com Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Extends the PLL frequency table of the AMD Geode-LX frame buffer driver to
make use of the DIV4 bit, thus adding support for dotclocks between 6 and 25
MHz. These are needed for small LCDs (e.g. 320x240). Also inserts some
intermediate steps between pre-existing frequencies.
The problem was the insertion of intermediate steps into the frequency
table; they would cause the wrong frequency to be matched. This patch
drops those intermediate frequencies while keeping the sub-25MHz
frequencies.
Signed-off-by: Andres Salomon <dilinger@debian.org> Signed-off-by: Jens Rottmann <JRottmann@LiPPERT-AT.de> Tested-by: Andres Salomon <dilinger@debian.org> Acked-by: Jordan Crouse <jordan.crouse@amd.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Dumazet [Wed, 14 May 2008 23:05:31 +0000 (16:05 -0700)]
oprofile: don't request cache line alignment for cpu_buffer
Alignment was previously requested because cpu_buffer was an [NR_CPUS]
array, to avoid cache line sharing between CPUS.
After commit 608dfddd845da5ab6accef70154c8910529699f7 (oprofile: change
cpu_buffer from array to per_cpu variable ), we dont need to force an
alignement anymore since cpu_buffer sits in per_cpu zone.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Cc: Mike Travis <travis@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There was some cleanup issues during early mount which would trigger
a kernel bug for certain types of failure. This patch reorganizes the
cleanup to get rid of the bad behavior.
This also merges the 9pnet and 9pnet_fd modules for the purpose of
configuration and initialization. Keeping the fd transport separate
from the core 9pnet code seemed like a good idea at the time, but in
practice has caused more harm and confusion than good.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
9p: make cryptic unknown error from server less scary
Right now when we get an error string from the server that we can't
map we report a cryptic error that actually makes it look like we are
reporting a problem with the client. This changes the text of the log
message to clarify where the error is coming from.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Steven Rostedt [Sat, 3 May 2008 22:29:50 +0000 (17:29 -0500)]
9p: fix flags length in net
Some files in the net/9p directory uses "int" for flags. This can
cause hard to find bugs on some architectures. This patch converts the
flags to use "long" instead.
This bug was discovered by doing an allyesconfig make on the -rt kernel
where checks are done to ensure all flags are of size sizeof(long).
Signed-off-by: Steven Rostedt <srostedt@redhat.com> Acked-by: Eric Van Hensbergen <ericvh@gmail.com>
projects / linux-2.6 / log