Roman Kagan [Fri, 22 Apr 2005 22:07:01 +0000 (15:07 -0700)]
[PATCH] USB: scripts/mod/file2alias.c: handle numeric ranges for USB bcdDevice
Another attempt at that...
The attached patch fixes the longstanding problem with USB bcdDevice
numeric ranges incorrectly converted into patterns for MODULE_ALIAS
generation. Previously it put both the lower and the upper limits into
the pattern, dlXdhY, making it impossible to fnmatch against except for
a few special cases, like dl*dh* or dlXdhX.
The patch makes it generate multiple MODULE_ALIAS lines covering the
whole range with fnmatch-able patterns. E.g. for a range between 0x0001
and 0x8345 it gives the following patterns:
Since bcdDevice is 2 bytes wide = 4 digits in hex representation, the
max no. of patters is 2 * 4 - 1 = 7.
The values are BCD (binary-coded decimals) and not hex, so patterns
using a dash seem to be safe regardless of locale collation order.
The patch changes bcdDevice part of the alias from dlXdhY to dZ, but
this shouldn't have big compatibility issues because fnmatch()-based
modprobing hasn't yet been widely used. Besides, the most common (and
almost the only working) case of dl*dh* becomes d* and thus continues to
work.
The patch is against 2.6.12-rc2, applies to -mm3 with an offset. The
matching patch to fix the MODALIAS environment variable now generated by
the usb hotplug function follows.
Signed-off-by: Roman Kagan <rkagan@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sven Anderson [Fri, 22 Apr 2005 22:06:58 +0000 (15:06 -0700)]
[PATCH] USB: clean up all iPod models in unusual_devs.h
Phil Dibowitz wrote:
> 1. You're adding product IDs 1202, 1203, 1204, and 1205. 1203 was
> already there, but you remove it, OK, but 1205 is already there, so
> you'll need to fix that.
I was not removing 1203, it's just the extension of the bcd range. You are
right about 1205, as I wrote, it was a patch against 2.6.11.7. Attached is
a patch against 2.6.12-rc2.
> 2. I'm OK with the full bcd range if Apple is changing it on firmware
> revs... fine, but it's bcd, not hex... 0x9999 =)
I just copied from other entries. There're a lot 0xffffs in unusual_dev.h,
so I assumed it is correct. I changed it to 0x9999.
> 3. It's rather obnoxious to take the original submitter's credit away.
I didn't remove it, I changed it to "based on...". Because I changed
something (the range) in his entry, I thought it is the best to take the
responsibility but keep the origin. Anyway, in the new patch I did it in a
different way.
> 4. Your /proc/bus/usb/devices shows 1204, but I see no evidence 1202 is
> really an iPod.
I don't have an old iPod mini, but you find a lot of evidence here:
> It also looks like 1205's entry is getting mangled, but I haven't
> attempted to apply the patch, so I'm not sure.
No, the patch was ok, but I agree it looks strange. It's not very
readable, because I cannot tell diff to work blockwise instead of
linewise. Because of the similarity of the entries, diff splits and merges
them. Anyway, the new patch "looks" better. ;-)
Signed-off-by: Sven Anderson <sven-linux@anderson.de> Signed-off-by: Phil Dibowitz <phil@ipom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David S. Miller [Fri, 22 Apr 2005 05:06:13 +0000 (22:06 -0700)]
[SPARC64]: In sunsu driver, make sure to fully init chip for kbd/ms
We were forgetting to call sunsu_change_speed(). The reason
that replugging in the mouse cable "fixes things" is that
causes a BREAK interrupt which in turn caused a call to
sunsu_change_speed() which would get the chip setup properly.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 22 Apr 2005 04:42:34 +0000 (21:42 -0700)]
[SPARC]: Provide generic ioctls in Sparc RTC driver.
Provide support for drivers/char/rtc.c ioctls in the
Mostek rtc driver as well as the Sparc specific RTCGET
and RTCSET.
This allows userspace to be much less messy. Currently
util-linux and other spots jump through hoops trying
various ioctl variants until it hits the right one whatever
driver actually being used supports.
Eventually all of this should move over to the genrtc.c
driver, but not today...
While we are here, fix up the register types for sparse.
Thanks to Frans Pop for helping point out this issue.
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Fri, 22 Apr 2005 00:13:59 +0000 (17:13 -0700)]
[TG3]: Add msi test
Add MSI test for chips that support MSI. If MSI test fails, it will
switch back to INTx mode and will print a message asking the user to
report the failure.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Fri, 22 Apr 2005 00:09:53 +0000 (17:09 -0700)]
[TG3]: Workaround 5752 A0 chip ID
The 5752 A0 chip ID is wrong in hardware. The simplest way to workaround
it is to change it to the correct value in tp->pci_chip_rev_id. This
way, it is easier to check for the ASIC_REV_5752 in the rest of the
driver.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Fri, 22 Apr 2005 00:09:08 +0000 (17:09 -0700)]
[TG3]: Fix tg3_set_power_state()
Fix tg3_set_power_state to drive GPIOs properly based on the
TG3_FLAG_EEPROM_WRITE_PROTECT flag. Some delays are also added after D0
and D3 power state changes.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Fri, 22 Apr 2005 00:06:20 +0000 (17:06 -0700)]
[TG3]: Split tg3_phy_probe into 2 functions
Split the 1st half of tg3_phy_probe() into tg3_get_eeprom_hw_cfg() so
that the TG3_FLAG_EEPROM_WRITE_PROT can be determined before calling
tg3_set_power_state() in tg3_get_invariants(). This will allow
tg3_set_power_state() to drive the GPIOs correctly based on the config.
information in eeprom.
On the 5752, there are no pull-up resistors on the GPIO pins and it is
necessary to drive the unused GPIOs as output.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville [Fri, 22 Apr 2005 00:03:52 +0000 (17:03 -0700)]
[TG3]: add support for bcm5752 rev a1
Replace existing ASIC_REV_5752 definition with ASIC_REV_5752_A0,
and add definition for ASIC_REV_5752_A1. Then, add ASIC_REV_5752_A1
to check for setting TG3_FLG2_5750_PLUS in tg3_get_invariants.
Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville [Thu, 21 Apr 2005 23:58:56 +0000 (16:58 -0700)]
[TG3]: add bcm5752 entry to pci_ids.h
Add proper entry for bcm5752 PCI ID to pci_ids.h, and use it in tg3.
I did this separately in case patches like this (i.e. new PCI IDs)
need to come from more "official" sources.
Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[AX25]: make ax25_queue_xmit a net_device parameter
I.e. not using skb->dev as a way to pass the parameter used to fill...
skb->dev :-)
Also to get the _type_trans open coded sequence grouped, next changesets
will introduce ax25_type_trans.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> Signed-off-by: David S. Miller <davem@davemloft.net>
James Bottomley [Thu, 21 Apr 2005 23:20:35 +0000 (16:20 -0700)]
[PATCH] fix subarch breakage in amd dual core updates
The patch to arch/i386/kernel/cpu/amd.c relies on the variable
cpu_core_id which is defined in i386/kernel/smpboot.c. This means it is
only present if CONFIG_X86_SMP is defined, not CONFIG_SMP (alternative
SMP harnesses won't have it, which is why it breaks voyager).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix non-legacy multichannel ISO receive, broken by Parag Wardukar's
allocation fix. Multichannel ISO receive still sucks; it should be possible
to use both legacy and non-legacy modes at the same time, but with this
patch, things are no worse than they were in 2.6.11 and allocation is
still done at the correct time.
The ia64-version of fls() never worked as intended (the bitnumbering
was off by 1 and fls(0) was undefined). This patch fixes the problem
by using a popcnt-based fls(), which on McKinley-derived cores is
slightly faster than both ia64_fls() and generic_fls(). The resulting
code, however, is bigger (7-8 bundles instead of about 3 bundles).
Also switch ia64_popcnt() to __builtin_popcountl() for GCC v3.4 or
newer since the compiler can predicate that and schedule it better.
Thanks to Simon Derr and Matt Mackall for tracking down this bug.
Signed-off-by: David Mosberger-Tang <davidm@hpl.hp.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
Thomas Graf [Wed, 20 Apr 2005 05:35:07 +0000 (22:35 -0700)]
[RTNETLINK]: Protocol family wildcard dumping for routing rules
Be kind to userspace and don't force them to hardcode protocol
families just to have it changed again once we support routing
rules for more than one protocol family.
Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Wed, 20 Apr 2005 05:32:22 +0000 (22:32 -0700)]
[IPV6]: Replace bogus instances of inet->recverr
While looking at this problem I noticed that IPv6 was sometimes
looking at inet->recverr which is bogus. Here is a patch to
correct that and use np->recverr.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Acked-by: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
ARM26 define FIRST_USER_ADDRESS as PAGE_SIZE (beyond the machine vectors when
they are mapped low), and use that definition in place of locally defined
MIN_MAP_ADDR. Previously, ARM26 permitted user mappings at 0 if the machine
vectors were mapped high; but that's inconsistent with ARM, and
FIRST_USER_ADDRESS would then have to be determined at runtime. Let's fix it
at PAGE_SIZE throughout the architecture.
ARM define FIRST_USER_ADDRESS as PAGE_SIZE (beyond the machine vectors when
they are mapped low), and use that definition in place of locally defined
MIN_MAP_ADDR.
Remove use of FIRST_USER_PGD_NR from sys_mincore: it's inconsistent (no other
syscall refers to it), unnecessary (sys_mincore loops over vmas further down)
and incorrect (misses user addresses in ARM's first pgd).
[PATCH] freepgt: free_pgtables from FIRST_USER_ADDRESS
The patches to free_pgtables by vma left problems on any architectures which
leave some user address page table entries unencapsulated by vma. Andi has
fixed the 32-bit vDSO on x86_64 to use a vma. Now fix arm (and arm26), whose
first PAGE_SIZE is reserved (perhaps) for machine vectors.
Our calls to free_pgtables must not touch that area, and exit_mmap's
BUG_ON(nr_ptes) must allow that arm's get_pgd_slow may (or may not) have
allocated an extra page table, which its free_pgd_slow would free later.
FIRST_USER_PGD_NR has misled me and others: until all the arches define
FIRST_USER_ADDRESS instead, a hack in mmap.c to derive one from t'other. This
patch fixes the bugs, the remaining patches just clean it up.
Once we're strict about clearing away page tables, hugetlb_prefault can assume
there are no page tables left within its range. Since the other arches
continue if !pte_none here, let i386 do the same.
ia64 and sparc64 hurriedly had to introduce their own variants of
pgd_addr_end, to leapfrog over the holes in their virtual address spaces which
the final clear_page_range suddenly presented when converted from pgd_index to
pgd_addr_end. But now that free_pgtables respects the vma list, those holes
are never presented, and the arch variants can go.
ia64 and ppc64 had hugetlb_free_pgtables functions which were no longer being
called, and it wasn't obvious what to do about them.
The ppc64 case turns out to be easy: the associated tables are noted elsewhere
and freed later, safe to either skip its hugetlb areas or go through the
motions of freeing nothing. Since ia64 does need a special case, restore to
ppc64 the special case of skipping them.
The ia64 hugetlb case has been broken since pgd_addr_end went in, though it
probably appeared to work okay if you just had one such area; in fact it's
been broken much longer if you consider a long munmap spanning from another
region into the hugetlb region.
In the ia64 hugetlb region, more virtual address bits are available than in
the other regions, yet the page tables are structured the same way: the page
at the bottom is larger. Here we need to scale down each addr before passing
it to the standard free_pgd_range. Was about to write a hugely_scaled_down
macro, but found htlbpage_to_page already exists for just this purpose. Fixed
off-by-one in ia64 is_hugepage_only_range.
Uninline free_pgd_range to make it available to ia64. Make sure the
vma-gathering loop in free_pgtables cannot join a hugepage_only_range to any
other (safe to join huges? probably but don't bother).
There's only one usage of MM_VM_SIZE(mm) left, and it's a troublesome macro
because mm doesn't contain the (32-bit emulation?) info needed. But it too is
only needed because we ignore the end from the vma list.
We could make flush_pgtables return that end, or unmap_vmas. Choose the
latter, since it's a natural fit with unmap_mapping_range_vma needing to know
its restart addr. This does make more than minimal change, but if unmap_vmas
had returned the end before, this is how we'd have done it, rather than
storing the break_addr in zap_details.
unmap_vmas used to return count of vmas scanned, but that's just debug which
hasn't been useful in a while; and if we want the map_count 0 on exit check
back, it can easily come from the final remove_vm_struct loop.
Recent woes with some arches needing their own pgd_addr_end macro; and 4-level
clear_page_range regression since 2.6.10's clear_page_tables; and its
long-standing well-known inefficiency in searching throughout the higher-level
page tables for those few entries to clear and free: all can be blamed on
ignoring the list of vmas when we free page tables.
Replace exit_mmap's clear_page_range of the total user address space by
free_pgtables operating on the mm's vma list; unmap_region use it in the same
way, giving floor and ceiling beyond which it may not free tables. This
brings lmbench fork/exec/sh numbers back to 2.6.10 (unless preempt is enabled,
in which case latency fixes spoil unmap_vmas throughput).
Beware: the do_mmap_pgoff driver failure case must now use unmap_region
instead of zap_page_range, since a page table might have been allocated, and
can only be freed while it is touched by some vma.
Move free_pgtables from mmap.c to memory.c, where its lower levels are adapted
from the clear_page_range levels. (Most of free_pgtables' old code was
actually for a non-existent case, prev not properly set up, dating from before
hch gave us split_vma.) Pass mmu_gather** in the public interfaces, since we
might want to add latency lockdrops later; but no attempt to do so yet, going
by vma should itself reduce latency.
But what if is_hugepage_only_range? Those ia64 and ppc64 cases need careful
examination: put that off until a later patch of the series.
What of x86_64's 32bit vdso page __map_syscall32 maps outside any vma?
And the range to sparc64's flush_tlb_pgtables? It's less clear to me now that
we need to do more than is done here - every PMD_SIZE ever occupied will be
flushed, do we really have to flush every PGDIR_SIZE ever partially occupied?
A shame to complicate it unnecessarily.
Special thanks to David Miller for time spent repairing my ceilings.
I can't use list.h, since sk_buff doesn't have a list_head but instead
has two struct sk_buff pointers, and I want to avoid any extra memory
allocation.
send outgoing packets in order
Signed-off-by: Ed L. Cashin <ecashin@coraid.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current <linux/debugfs.h> include file is a little fragile in that
it is not self-contained and hence may cause compile warnings or
errors depending on the files included before it, the kernel config
and the architecture. This patch makes things a little more robust by:
- including <linux/types.h> to get definitions of u32, mode_t, and so on.
- forward declaring struct file_operations.
- including <linux/err.h> when CONFIG_DEBUG_FS is not set
The last change is particularly useful, as a kernel developer is
likely to build with debugfs always enabled and never see the build
breakage cased if debugfs is disabled.
Signed-off-by: Roland Dreier <roland@topspin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / linux-2.6 / log