Kim Phillips [Thu, 17 Jul 2008 12:20:06 +0000 (20:20 +0800)]
crypto: talitos - Stop leaking memory in error path
free edescriptor when returning error (such as -EAGAIN).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Acked-by: Lee Nipper <lee.nipper@freescale.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Kim Phillips [Thu, 17 Jul 2008 12:19:18 +0000 (20:19 +0800)]
crypto: talitos - Fix GFP flag usage
use GFP_ATOMIC when necessary; use atomic_t when allocating submit_count.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Acked-by: Lee Nipper <lee.nipper@freescale.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Kim Phillips [Thu, 17 Jul 2008 12:16:40 +0000 (20:16 +0800)]
crypto: talitos - Preempt overflow interrupts
add requests pending/submit count to prevent request queue full
condition by preempting h/w overflow interrupts in software.
We do this due to the delay in the delivery and handling of the
channel overflow error interrupt.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Acked-by: Lee Nipper <lee.nipper@freescale.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Lee Nipper [Thu, 17 Jul 2008 08:22:30 +0000 (16:22 +0800)]
crypto: talitos - Correct dst != src case handling
Seems that dst == src, but this fixes the logic in case it's not.
Signed-off-by: Lee Nipper <lee.nipper@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Lee Nipper [Thu, 17 Jul 2008 07:58:08 +0000 (15:58 +0800)]
crypto: talitos - Remove calls to of_node_put
Remove of_node_put calls since there is no corresponding of_node_get.
This patch prevents an exception when talitos is loaded a 2nd time.
This sequence: modprobe talitos; rmmod talitos; modprobe talitos
causes this message: "WARNING: Bad of_node_put() on /soc8349@e0000000/crypto@30000".
Signed-off-by: Lee Nipper <lee.nipper@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Merge branch 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (72 commits)
Revert "x86/PCI: ACPI based PCI gap calculation"
PCI: remove unnecessary volatile in PCIe hotplug struct controller
x86/PCI: ACPI based PCI gap calculation
PCI: include linux/pm_wakeup.h for device_set_wakeup_capable
PCI PM: Fix pci_prepare_to_sleep
x86/PCI: Fix PCI config space for domains > 0
Fix acpi_pm_device_sleep_wake() by providing a stub for CONFIG_PM_SLEEP=n
PCI: Simplify PCI device PM code
PCI PM: Introduce pci_prepare_to_sleep and pci_back_from_sleep
PCI ACPI: Rework PCI handling of wake-up
ACPI: Introduce new device wakeup flag 'prepared'
ACPI: Introduce acpi_device_sleep_wake function
PCI: rework pci_set_power_state function to call platform first
PCI: Introduce platform_pci_power_manageable function
ACPI: Introduce acpi_bus_power_manageable function
PCI: make pci_name use dev_name
PCI: handle pci_name() being const
PCI: add stub for pci_set_consistent_dma_mask()
PCI: remove unused arch pcibios_update_resource() functions
PCI: fix pci_setup_device()'s sprinting into a const buffer
...
Fixed up conflicts in various files (arch/x86/kernel/setup_64.c,
arch/x86/pci/irq.c, arch/x86/pci/pci.h, drivers/acpi/sleep/main.c,
drivers/pci/pci.c, drivers/pci/pci.h, include/acpi/acpi_bus.h) from x86
and ACPI updates manually.
Merge branch 'for_linus' of git://git.infradead.org/~dedekind/ubifs-2.6
* 'for_linus' of git://git.infradead.org/~dedekind/ubifs-2.6:
UBIFS: include to compilation
UBIFS: add new flash file system
UBIFS: add brief documentation
MAINTAINERS: add UBIFS section
do_mounts: allow UBI root device name
VFS: export sync_sb_inodes
VFS: move inode_lock into sync_sb_inodes
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (76 commits)
IDE: Report errors during drive reset back to user space
Update documentation of HDIO_DRIVE_RESET ioctl
IDE: Remove unused code
IDE: Fix HDIO_DRIVE_RESET handling
hd.c: remove the #include <linux/mc146818rtc.h>
update the BLK_DEV_HD help text
move ide/legacy/hd.c to drivers/block/
ide/legacy/hd.c: use late_initcall()
remove BLK_DEV_HD_ONLY
ide: endian annotations in ide-floppy.c
ide-floppy: zero out the whole struct ide_atapi_pc on init
ide-floppy: fold idefloppy_create_test_unit_ready_cmd into idefloppy_open
ide-cd: move request prep chunk from cdrom_do_newpc_cont to rq issue path
ide-cd: move request prep from cdrom_start_rw_cont to rq issue path
ide-cd: move request prep from cdrom_start_seek_continuation to rq issue path
ide-cd: fold cdrom_start_seek into ide_cd_do_request
ide-cd: simplify request issuing path
ide-cd: mv ide_do_rw_cdrom ide_cd_do_request
ide-cd: cdrom_start_seek: remove unused argument block
ide-cd: ide_do_rw_cdrom: add the catch-all bad request case to the if-else block
...
Merge branch 'release-2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-acpi-merge-2.6
* 'release-2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-acpi-merge-2.6: (87 commits)
Fix FADT parsing
Add the ability to reset the machine using the RESET_REG in ACPI's FADT table.
ACPI: use dev_printk when possible
PNPACPI: add support for HP vendor-specific CCSR descriptors
PNP: avoid legacy IDE IRQs
PNP: convert resource options to single linked list
ISAPNP: handle independent options following dependent ones
PNP: remove extra 0x100 bit from option priority
PNP: support optional IRQ resources
PNP: rename pnp_register_*_resource() local variables
PNPACPI: ignore _PRS interrupt numbers larger than PNP_IRQ_NR
PNP: centralize resource option allocations
PNP: remove redundant pnp_can_configure() check
PNP: make resource assignment functions return 0 (success) or -EBUSY (failure)
PNP: in debug resource dump, make empty list obvious
PNP: improve resource assignment debug
PNP: increase I/O port & memory option address sizes
PNP: introduce pnp_irq_mask_t typedef
PNP: make resource option structures private to PNP subsystem
PNP: define PNP-specific IORESOURCE_IO_* flags alongside IRQ, DMA, MEM
...
* git://git.linux-nfs.org/projects/trondmy/nfs-2.6: (82 commits)
NFSv4: Remove BKL from the nfsv4 state recovery
SUNRPC: Remove the BKL from the callback functions
NFS: Remove BKL from the readdir code
NFS: Remove BKL from the symlink code
NFS: Remove BKL from the sillydelete operations
NFS: Remove the BKL from the rename, rmdir and unlink operations
NFS: Remove BKL from NFS lookup code
NFS: Remove the BKL from nfs_link()
NFS: Remove the BKL from the inode creation operations
NFS: Remove BKL usage from open()
NFS: Remove BKL usage from the write path
NFS: Remove the BKL from the permission checking code
NFS: Remove attribute update related BKL references
NFS: Remove BKL requirement from attribute updates
NFS: Protect inode->i_nlink updates using inode->i_lock
nfs: set correct fl_len in nlmclnt_test()
SUNRPC: Support registering IPv6 interfaces with local rpcbind daemon
SUNRPC: Refactor rpcb_register to make rpcbindv4 support easier
SUNRPC: None of rpcb_create's callers wants a privileged source port
SUNRPC: Introduce a specific rpcb_create for contacting localhost
...
Jan Beulich [Wed, 16 Jul 2008 21:27:08 +0000 (23:27 +0200)]
Fix FADT parsing
The (1.0 inherited) separate length fields in the FADT are byte granular.
Further, PM1a/b may have distinct lengths and live in distinct address spaces.
acpi_tb_convert_fadt() should account for all of these conditions.
Apart from these changes I'm puzzled by the fact that, not just for
acpi_gbl_xpm1{a,b}_enable, acpi_hw_low_level_{read,write}() get an explicit
size passed rather than using the size found in the passed GAS. What happens
on a platform that defines PM1{a,b} wider than 16 bits? Of course,
acpi_hw_low_level_{read,write}() at present are entirely un-prepared to deal
with sizes other than 8, 16, or 32, not to speak of a non-zero bit_offset or
access_width...
Signed-off-by: Jan Beulich <jbeulich@novell.com> Signed-off-by: Andi Kleen <ak@linux.intel.com> Cc: Len Brown <lenb@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Bjorn Helgaas [Fri, 27 Jun 2008 22:57:19 +0000 (16:57 -0600)]
PNPACPI: add support for HP vendor-specific CCSR descriptors
The HP CCSR descriptor describes MMIO address space that should appear
as a MEM resource. This patch adds support for parsing these descriptors
in the _CRS data.
The visible effect of this is that these MEM resources will appear
in /sys/devices/pnp0/.../resources, which means that "lspnp -v" will
report it, user applications can use this to locate device CSR space,
and kernel drivers can use the normal PNP resource accessors to
locate them.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Bjorn Helgaas [Fri, 27 Jun 2008 22:57:18 +0000 (16:57 -0600)]
PNP: avoid legacy IDE IRQs
If an IDE controller is in compatibility mode, it expects to use
IRQs 14 and 15, so PNP should avoid them.
This patch should resolve this problem report:
parallel driver grabs IRQ14 preventing legacy SFF ATA controller from working
https://bugzilla.novell.com/show_bug.cgi?id=375836
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Bjorn Helgaas [Fri, 27 Jun 2008 22:57:17 +0000 (16:57 -0600)]
PNP: convert resource options to single linked list
ISAPNP, PNPBIOS, and ACPI describe the "possible resource settings" of
a device, i.e., the possibilities an OS bus driver has when it assigns
I/O port, MMIO, and other resources to the device.
PNP used to maintain this "possible resource setting" information in
one independent option structure and a list of dependent option
structures for each device. Each of these option structures had lists
of I/O, memory, IRQ, and DMA resources, for example:
This data structure was designed for ISAPNP, where the OS configures
device resource settings by writing directly to configuration
registers. The OS can write the registers in arbitrary order much
like it writes PCI BARs.
However, for PNPBIOS and ACPI devices, the OS uses firmware interfaces
that perform device configuration, and it is important to pass the
desired settings to those interfaces in the correct order. The OS
learns the correct order by using firmware interfaces that return the
"current resource settings" and "possible resource settings," but the
option structures above doesn't store the ordering information.
This patch replaces the independent and dependent lists with a single
list of options. For example, a device might have possible resource
settings like this:
dev
options
ind-io0 -> dep0-io0 -> dep1->io0 -> ind-io1 ...
All the possible settings are in the same list, in the order they
come from the firmware "possible resource settings" list. Each entry
is tagged with an independent/dependent flag. Dependent entries also
have a "set number" and an optional priority value. All dependent
entries must be assigned from the same set. For example, the OS can
use all the entries from dependent set 0, or all the entries from
dependent set 1, but it cannot mix entries from set 0 with entries
from set 1.
Prior to this patch PNP didn't keep track of the order of this list,
and it assigned all independent options first, then all dependent
ones. Using the example above, that resulted in a "desired
configuration" list like this:
ind->io0 -> ind->io1 -> depN-io0 ...
instead of the list the firmware expects, which looks like this:
ind->io0 -> depN-io0 -> ind-io1 ...
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Andi Kleen <ak@linux.intel.com> Acked-by: Rene Herman <rene.herman@gmail.com> Signed-off-by: Len Brown <len.brown@intel.com>
Bjorn Helgaas [Fri, 27 Jun 2008 22:57:16 +0000 (16:57 -0600)]
ISAPNP: handle independent options following dependent ones
The ISAPNP spec recommends that independent options precede
dependent ones, but this is not actually required. The current
ISAPNP code incorrectly puts such trailing independent options
at the end of the last dependent option list.
This patch fixes that bug by resetting the current option list
to the independent list when we see an "End Dependent Functions"
tag. PNPBIOS and PNPACPI handle this the same way.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Andi Kleen <ak@linux.intel.com> Acked-by: Rene Herman <rene.herman@gmail.com> Signed-off-by: Len Brown <len.brown@intel.com>
Bjorn Helgaas [Fri, 27 Jun 2008 22:57:15 +0000 (16:57 -0600)]
PNP: remove extra 0x100 bit from option priority
When building resource options, ISAPNP and PNPBIOS set the priority
to something like "0x100 | PNP_RES_PRIORITY_ACCEPTABLE", but we
immediately mask off the 0x100 again in pnp_build_option(), so that
bit looks superfluous.
Thanks to Rene Herman <rene.herman@gmail.com> for pointing this out.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Andi Kleen <ak@linux.intel.com> Acked-by: Rene Herman <rene.herman@gmail.com> Signed-off-by: Len Brown <len.brown@intel.com>
Bjorn Helgaas [Fri, 27 Jun 2008 22:57:14 +0000 (16:57 -0600)]
PNP: support optional IRQ resources
This patch adds an IORESOURCE_IRQ_OPTIONAL flag for use when
assigning resources to a device. If the flag is set and we are
unable to assign an IRQ to the device, we can leave the IRQ
disabled but allow the overall resource allocation to succeed.
Some devices request an IRQ, but can run without an IRQ
(possibly with degraded performance). This flag lets us run
the device without the IRQ instead of just leaving the
device disabled.
This is a reimplementation of this previous change by Rene
Herman <rene.herman@gmail.com>:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=3b73a223661ed137c5d3d2635f954382e94f5a43
I reimplemented this for two reasons:
- to prepare for converting all resource options into a single linked
list, as opposed to the per-resource-type lists we have now, and
- to preserve the order and number of resource options.
In PNPBIOS and ACPI, we configure a device by giving firmware a
list of resource assignments. It is important that this list
has exactly the same number of resources, in the same order,
as the "template" list we got from the firmware in the first
place.
The problem of a sound card MPU401 being left disabled for want of
an IRQ was reported by Uwe Bugla <uwe.bugla@gmx.de>.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Andi Kleen <ak@linux.intel.com> Acked-by: Rene Herman <rene.herman@gmail.com> Signed-off-by: Len Brown <len.brown@intel.com>
Bjorn Helgaas [Fri, 27 Jun 2008 22:57:12 +0000 (16:57 -0600)]
PNPACPI: ignore _PRS interrupt numbers larger than PNP_IRQ_NR
ACPI Extended Interrupt Descriptors can encode 32-bit interrupt
numbers, so an interrupt number may exceed the size of the bitmap
we use to track possible IRQ settings.
To avoid corrupting memory, complain and ignore too-large interrupt
numbers.
There's similar code in pnpacpi_parse_irq_option(), but I didn't
change that because the small IRQ descriptor can only encode
IRQs 0-15, which do not exceed bitmap size.
In the future, we could handle IRQ numbers greater than PNP_IRQ_NR
by replacing the bitmap with a table or list.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Andi Kleen <ak@linux.intel.com> Acked-by: Rene Herman <rene.herman@gmail.com> Signed-off-by: Len Brown <len.brown@intel.com>
Bjorn Helgaas [Fri, 27 Jun 2008 22:57:11 +0000 (16:57 -0600)]
PNP: centralize resource option allocations
This patch moves all the option allocations (pnp_mem, pnp_port, etc)
into the pnp_register_{mem,port,irq,dma}_resource() functions. This
will make it easier to rework the option data structures.
The non-trivial part of this patch is the IRQ handling. The backends
have to allocate a local pnp_irq_mask_t bitmap, populate it, and pass
a pointer to pnp_register_irq_resource().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Andi Kleen <ak@linux.intel.com> Acked-by: Rene Herman <rene.herman@gmail.com> Signed-off-by: Len Brown <len.brown@intel.com>
Bjorn Helgaas [Fri, 27 Jun 2008 22:57:09 +0000 (16:57 -0600)]
PNP: make resource assignment functions return 0 (success) or -EBUSY (failure)
This patch doesn't change any behavior; it just makes the return
values more conventional.
This changes pnp_assign_dma() from a void function to one that
returns an int, just like the other assignment functions. For
now, at least, pnp_assign_dma() always returns 0 (success), so
it appears to never fail, just like before.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Andi Kleen <ak@linux.intel.com> Acked-by: Rene Herman <rene.herman@gmail.com> Signed-off-by: Len Brown <len.brown@intel.com>
Bjorn Helgaas [Fri, 27 Jun 2008 22:57:08 +0000 (16:57 -0600)]
PNP: in debug resource dump, make empty list obvious
If the resource list is empty, say that explicitly. Previously,
it was confusing because often the heading was followed by zero
resource lines, then some "add resource" lines from auto-assignment,
so the "add" lines looked like current resources.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Andi Kleen <ak@linux.intel.com> Acked-by: Rene Herman <rene.herman@gmail.com> Signed-off-by: Len Brown <len.brown@intel.com>
Bjorn Helgaas [Fri, 27 Jun 2008 22:57:06 +0000 (16:57 -0600)]
PNP: increase I/O port & memory option address sizes
ACPI Address Space Descriptors can be up to 64 bits wide.
We should keep track of the whole thing when parsing resource
options, so this patch changes PNP port and mem option
fields from "unsigned short" and "unsigned int" to
"resource_size_t".
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Andi Kleen <ak@linux.intel.com> Acked-by: Rene Herman <rene.herman@gmail.com> Signed-off-by: Len Brown <len.brown@intel.com>
Bjorn Helgaas [Fri, 27 Jun 2008 22:57:05 +0000 (16:57 -0600)]
PNP: introduce pnp_irq_mask_t typedef
This adds a typedef for the IRQ bitmap, which should cause
no functional change, but will make it easier to pass a
pointer to a bitmap to pnp_register_irq_resource().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Andi Kleen <ak@linux.intel.com> Acked-by: Rene Herman <rene.herman@gmail.com> Signed-off-by: Len Brown <len.brown@intel.com>
Bjorn Helgaas [Fri, 27 Jun 2008 22:57:04 +0000 (16:57 -0600)]
PNP: make resource option structures private to PNP subsystem
Nothing outside the PNP subsystem should need access to a
device's resource options, so this patch moves the option
structure declarations to a private header file.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Andi Kleen <ak@linux.intel.com> Acked-by: Rene Herman <rene.herman@gmail.com> Signed-off-by: Len Brown <len.brown@intel.com>
Bjorn Helgaas [Fri, 27 Jun 2008 22:57:03 +0000 (16:57 -0600)]
PNP: define PNP-specific IORESOURCE_IO_* flags alongside IRQ, DMA, MEM
PNP previously defined PNP_PORT_FLAG_16BITADDR and PNP_PORT_FLAG_FIXED
in a private header file, but put those flags in struct resource.flags
fields. Better to make them IORESOURCE_IO_* flags like the existing
IRQ, DMA, and MEM flags.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Andi Kleen <ak@linux.intel.com> Acked-by: Rene Herman <rene.herman@gmail.com> Signed-off-by: Len Brown <len.brown@intel.com>
Bjorn Helgaas [Fri, 27 Jun 2008 22:57:01 +0000 (16:57 -0600)]
PNP: add pnp_possible_config() -- can a device could be configured this way?
As part of a heuristic to identify modem devices, 8250_pnp.c
checks to see whether a device can be configured at any of the
legacy COM port addresses.
This patch moves the code that traverses the PNP "possible resource
options" from 8250_pnp.c to the PNP subsystem. This encapsulation
is important because a future patch will change the implementation
of those resource options.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Andi Kleen <ak@linux.intel.com> Acked-by: Rene Herman <rene.herman@gmail.com> Signed-off-by: Len Brown <len.brown@intel.com>
Bjorn Helgaas [Fri, 27 Jun 2008 22:57:00 +0000 (16:57 -0600)]
PNP: dont sort by type in /sys/.../resources
Rather than stepping through all IO resources, then stepping through
all MMIO resources, etc., we can just iterate over the resource list
once directly.
This can change the order in /sys, e.g.,
# cat /sys/devices/pnp0/00:07/resources # OLD
state = active
io 0x3f8-0x3ff
irq 4
# cat /sys/devices/pnp0/00:07/resources # NEW
state = active
irq 4
io 0x3f8-0x3ff
The old code artificially sorted resources by type; the new code
just lists them in the order we read them from the ISAPNP hardware
or the BIOS.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Bjorn Helgaas [Fri, 27 Jun 2008 22:56:59 +0000 (16:56 -0600)]
PNP: remove ratelimit on add resource failures
We used to have a fixed-size resource table. If a device had
twenty resources when the table only had space for ten, we didn't
need ten warnings, so we added the ratelimit.
Now that we can dynamically allocate new resources, we should
only get failures if the allocation fails. That should be
rare enough that we don't need to ratelimit the messages.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Bjorn Helgaas [Fri, 27 Jun 2008 22:56:58 +0000 (16:56 -0600)]
PNPACPI: keep disabled resources when parsing current config
When we parse a device's _CRS data (the current resource settings),
we should keep track of everything we find, even if it's currently
disabled or invalid.
This is what we already do for ISAPNP and PNPBIOS, and it helps
keep things matched up when we subsequently re-encode resources.
For example, consider a device with (mem, irq0, irq1, io), where
irq0 is disabled. If we drop irq0 when parsing the _CRS, we will
mistakenly put irq1 in the irq0 slot when we encode resources
for an _SRS call.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Bjorn Helgaas [Fri, 27 Jun 2008 22:56:57 +0000 (16:56 -0600)]
PNP: replace pnp_resource_table with dynamically allocated resources
PNP used to have a fixed-size pnp_resource_table for tracking the
resources used by a device. This table often overflowed, so we've
had to increase the table size, which wastes memory because most
devices have very few resources.
This patch replaces the table with a linked list of resources where
the entries are allocated on demand.
This removes messages like these:
pnpacpi: exceeded the max number of IO resources
00:01: too many I/O port resources
This patch also changes the way PNP uses the IORESOURCE_UNSET,
IORESOURCE_AUTO, and IORESOURCE_DISABLED flags.
Prior to this patch, the pnp_resource_table entries used the flags
like this:
IORESOURCE_UNSET
This table entry is unused and available for use. When this flag
is set, we shouldn't look at anything else in the resource structure.
This flag is set when a resource table entry is initialized.
IORESOURCE_AUTO
This resource was assigned automatically by pnp_assign_{io,mem,etc}().
This flag is set when a resource table entry is initialized and
cleared whenever we discover a resource setting by reading an ISAPNP
config register, parsing a PNPBIOS resource data stream, parsing an
ACPI _CRS list, or interpreting a sysfs "set" command.
Resources marked IORESOURCE_AUTO are reinitialized and marked as
IORESOURCE_UNSET by pnp_clean_resource_table() in these cases:
- before we attempt to assign resources automatically,
- if we fail to assign resources automatically,
- after disabling a device
IORESOURCE_DISABLED
Set by pnp_assign_{io,mem,etc}() when automatic assignment fails.
Also set by PNPBIOS and PNPACPI for:
- invalid IRQs or GSI registration failures
- invalid DMA channels
- I/O ports above 0x10000
- mem ranges with negative length
After this patch, there is no pnp_resource_table, and the resource list
entries use the flags like this:
IORESOURCE_UNSET
This flag is no longer used in PNP. Instead of keeping
IORESOURCE_UNSET entries in the resource list, we remove
entries from the list and free them.
IORESOURCE_AUTO
No change in meaning: it still means the resource was assigned
automatically by pnp_assign_{port,mem,etc}(), but these functions
now set the bit explicitly.
We still "clean" a device's resource list in the same places,
but rather than reinitializing IORESOURCE_AUTO entries, we
just remove them from the list.
Note that IORESOURCE_AUTO entries are always at the end of the
list, so removing them doesn't reorder other list entries.
This is because non-IORESOURCE_AUTO entries are added by the
ISAPNP, PNPBIOS, or PNPACPI "get resources" methods and by the
sysfs "set" command. In each of these cases, we completely free
the resource list first.
IORESOURCE_DISABLED
In addition to the cases where we used to set this flag, ISAPNP now
adds an IORESOURCE_DISABLED resource when it reads a configuration
register with a "disabled" value.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Bjorn Helgaas [Fri, 27 Jun 2008 22:56:56 +0000 (16:56 -0600)]
PNP: make pnp_{port,mem,etc}_start(), et al work for invalid resources
Some callers use pnp_port_start() and similar functions without
making sure the resource is valid. This patch makes us fall
back to returning the initial values if the resource is not
valid or not even present.
This mostly preserves the previous behavior, where we would just
return the initial values set by pnp_init_resource_table(). The
original 2.6.25 code didn't range-check the "bar", so it would
return garbage if the bar exceeded the table size. This code
returns sensible values instead.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Bjorn Helgaas [Fri, 27 Jun 2008 22:56:55 +0000 (16:56 -0600)]
PNP: add pnp_resource_type_name() helper function
This patch adds a "pnp_resource_type_name(struct resource *)" that
returns the string resource type. This will be used by the sysfs
"show resources" function and the debug resource dump function.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Bjorn Helgaas [Fri, 27 Jun 2008 22:56:53 +0000 (16:56 -0600)]
PNP: remove pnp_resource.index
We used pnp_resource.index to keep track of which ISAPNP configuration
register a resource should be written to. We needed this only to
handle the case where a register is disabled but a subsequent register
in the same set is enabled.
Rather than explicitly maintaining the pnp_resource.index, this patch
adds a resource every time we read an ISAPNP configuration register
and marks the resource as IORESOURCE_DISABLED when appropriate. This
makes the position in the pnp_resource_table always correspond to the
config register index.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Zhao Yakui [Tue, 24 Jun 2008 10:02:57 +0000 (18:02 +0800)]
ACPI: Disable MWAIT via DMI on broken Compal board
If a system matches in this DMI table,
Linux will disable MWAIT support for idle.
ie. "idle=nomwait" is automatically invoked
and C1_FFH and C2C3_FFH access mode are disabled.
Zhao Yakui [Tue, 17 Jun 2008 06:39:59 +0000 (14:39 +0800)]
ACPI: Disable the C2C3_FFH access mode HW has no MWAIT support
991528d7348667924176f3e29addea0675298944
(ACPI: Processor native C-states using MWAIT)
started passing C2C3_FFH to _PDC to tell the BIOS
that Linux supports MWAIT for deep C-states.
However, we should first double check with the hardware
that it actually supports MWAIT before potentially exposing
a BIOS bug of an MWAIT _CST on HW that doesn't support MWAIT.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com> Signed-off-by: Li Shaohua <shaohua.li@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Bob Moore [Tue, 10 Jun 2008 06:30:04 +0000 (14:30 +0800)]
ACPICA: Fix mutex debug code for wrong loop termination value
Loop was terminating one iteration early, missing one of the
debugger handshake mutexes. Linn Crosetto.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Bob Moore [Tue, 10 Jun 2008 06:27:55 +0000 (14:27 +0800)]
ACPICA: Cleanup of _PRT parsing code
Removed extraneous else clauses, other general cleanup.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Bob Moore [Tue, 10 Jun 2008 06:25:05 +0000 (14:25 +0800)]
ACPICA: Cleanup debug operand dump mechanism
Eliminated unnecessary operands; eliminated use of negative index
in loop. Operands now displayed in correct order, not backwards.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Bob Moore [Tue, 10 Jun 2008 06:21:05 +0000 (14:21 +0800)]
ACPICA: Fix for invalid large array index on 64-bit systems
This problem was introduced in 20080514 as a result of the
elimination of the acpi_native_uint type. Code uses a negative
array index, which should be eliminated.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Bob Moore [Tue, 10 Jun 2008 06:19:32 +0000 (14:19 +0800)]
ACPICA: Update disassembler for DMAR table changes
Now supports the 2007 intel Virtualization Technology for Directed
I/O specification.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Bob Moore [Tue, 10 Jun 2008 07:54:40 +0000 (15:54 +0800)]
ACPICA: Update DMAR and SRAT table definitions
Synchronized tables with current specifications.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Bob Moore [Tue, 10 Jun 2008 06:16:47 +0000 (14:16 +0800)]
ACPICA: Workaround for reversed _PRT entries from BIOS
Some BIOSs erroneously reverse the _PRT SourceName and the
SourceIndex. Detect and repair this problem. MS ACPI also allows
and repairs this problem, thus ACPICA must also.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Bob Moore [Tue, 10 Jun 2008 05:55:53 +0000 (13:55 +0800)]
ACPICA: Add const qualifier for appropriate string constants
Mostly MODULE_NAME and printf format strings.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Bob Moore [Tue, 10 Jun 2008 05:44:48 +0000 (13:44 +0800)]
ACPICA: Several lint changes, no functional changes
Remove pointer cast warnings and fix for a debug printf.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Bob Moore [Tue, 10 Jun 2008 05:43:34 +0000 (13:43 +0800)]
ACPICA: Removed unused include files from source files
From lint.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Bob Moore [Tue, 10 Jun 2008 05:42:13 +0000 (13:42 +0800)]
ACPICA: Eliminate acpi_native_uint type v2
No longer needed; replaced mostly with u32, but also acpi_size
where a type that changes 32/64 bit on 32/64-bit platforms is
required.
v2: Fix a cast of a 32-bit int to a pointer in ACPI to avoid a compiler warning.
from David Howells
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Bob Moore [Tue, 10 Jun 2008 04:53:01 +0000 (12:53 +0800)]
ACPICA: Fix possible negative array index in acpi_ut_validate_exception
Added NULL fields to the exception string arrays to eliminate
the -1 subtraction on the SubStatus field.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Jan Beulich [Tue, 10 Jun 2008 04:49:56 +0000 (12:49 +0800)]
ACPICA: Update tracking macros to reduce code/data size
Changed ACPI_MODULE_NAME and ACPI_FUNCTION_NAME to use arrays of
strings instead of pointers to static strings. Jan Beulich and
Bob Moore.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Bob Moore [Tue, 10 Jun 2008 04:38:10 +0000 (12:38 +0800)]
ACPICA: Fix for hang on GPE method invocation
Fixes problem where the new method argument count validation mechanism
will enter an infinite loop when a GPE method is dispatched.
Problem fixed be removing the obsolete code that passes GPE block
information to the notify handler via the control method parameter pointer.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Bob Moore [Tue, 10 Jun 2008 04:25:42 +0000 (12:25 +0800)]
ACPICA: Add argument count checking to control method invocation via acpi_evaluate_object
Error if too few arguments, warning if too many. This applies
only to external programmatic control method execution, not
method-to-method calls within the AML.
Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Randy Dunlap [Fri, 27 Jun 2008 02:27:21 +0000 (22:27 -0400)]
fujitsu-laptop: depends on INPUT
fujitsu-laptop uses input_* functions, so it should depend on INPUT.
drivers/built-in.o: In function `acpi_fujitsu_add':
fujitsu-laptop.c:(.text+0xaaec7): undefined reference to `input_allocate_device'
fujitsu-laptop.c:(.text+0xaaf39): undefined reference to `input_register_device'
fujitsu-laptop.c:(.text+0xab025): undefined reference to `input_free_device'
drivers/built-in.o: In function `acpi_fujitsu_notify':
fujitsu-laptop.c:(.text+0xab0d8): undefined reference to `input_event'
fujitsu-laptop.c:(.text+0xab0e5): undefined reference to `input_event'
fujitsu-laptop.c:(.text+0xab0f5): undefined reference to `input_event'
fujitsu-laptop.c:(.text+0xab102): undefined reference to `input_event'
drivers/built-in.o: In function `acpi_fujitsu_hotkey_notify':
fujitsu-laptop.c:(.text+0xab261): undefined reference to `input_event'
drivers/built-in.o:fujitsu-laptop.c:(.text+0xab26e): more undefined references to `input_event' follow
drivers/built-in.o: In function `acpi_fujitsu_hotkey_add':
fujitsu-laptop.c:(.text+0xab49c): undefined reference to `input_allocate_device'
fujitsu-laptop.c:(.text+0xab51a): undefined reference to `input_register_device'
fujitsu-laptop.c:(.text+0xab5e4): undefined reference to `input_free_device'
make[1]: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andi Kleen <ak@linux.intel.com> Acked-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com>
We can avoid taking the BKL in snapshot_ioctl() if pm_mutex is used to prevent
the ioctls from being executed concurrently.
In addition, although it is only possible to open /dev/snapshot once, the task
which has done that may spawn a child that will inherit the open descriptor,
so in theory they can call snapshot_write(), snapshot_read() and
snapshot_release() concurrently. pm_mutex can also be used for mutual
exclusion in such cases.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Andi Kleen <ak@linux.intel.com> Acked-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Len Brown <len.brown@intel.com>
Alan Cox [Wed, 11 Jun 2008 20:07:52 +0000 (22:07 +0200)]
snapshot: Push BKL down into ioctl handlers
Push BKL down into ioctl handlers - snapshot device.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
The freezer currently attempts to distinguish kernel threads from
user space tasks by checking if their mm pointer is unset and it
does not send fake signals to kernel threads. However, there are
kernel threads, mostly related to networking, that behave like
user space tasks and may want to be sent a fake signal to be frozen.
Introduce the new process flag PF_FREEZER_NOSIG that will be set
by default for all kernel threads and make the freezer only send
fake signals to the tasks having PF_FREEZER_NOSIG unset. Provide
the set_freezable_with_signal() function to be called by the kernel
threads that want to be sent a fake signal for freezing.
This patch should not change the freezer's observable behavior.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Andi Kleen <ak@linux.intel.com> Acked-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Len Brown <len.brown@intel.com>
Johannes Berg [Wed, 11 Jun 2008 20:03:10 +0000 (22:03 +0200)]
APM emulation: Notify about all suspend events, not just APM invoked ones (v2)
This revamps the apm-emulation code to get suspend notifications
regardless of what way pm_suspend() was invoked, whether via the
apm ioctl or via /sys/power/state. Also do some code cleanup and
add comments while at it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Remove the obsolete workaround for a Toshiba Satellite 4030cdt
S1 problem from drivers/acpi/sleep/main.c .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Andi Kleen <ak@linux.intel.com> Acked-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Len Brown <len.brown@intel.com>
PCI ACPI: Drop the second argument of platform_pci_choose_state
Since the second argument of acpi_pci_choose_state() and
platform_pci_choose_state() is never used, remove it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Andi Kleen <ak@linux.intel.com> Acked-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Len Brown <len.brown@intel.com>
David Brownell [Wed, 4 Jun 2008 23:15:40 +0000 (01:15 +0200)]
ACPI PM: acpi_pm_device_sleep_state() cleanup
Get rid of a superfluous acpi_pm_device_sleep_state() parameter. The
only legitimate value of that parameter must be derived from the first
parameter, which is what all the callers already do. (However, this
does not address the fact that ACPI still doesn't set up those flags.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andi Kleen <ak@linux.intel.com> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Len Brown <len.brown@intel.com>
Carlos Corbacho [Sat, 21 Jun 2008 08:09:58 +0000 (09:09 +0100)]
acer-wmi: Remove version number
It doesn't make much sense these days.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Carlos Corbacho [Sat, 21 Jun 2008 08:09:53 +0000 (09:09 +0100)]
acer-wmi: Add debugfs file for device detection
Add a debugfs file for showing the full results of the method we use to
detect devices on WMID laptops.
This should be useful in the case that a Linux user gets an Acer laptop
with 3G support (and/ or people who enjoy ripping their wireless cards out)
so we can get some feedback on how this value changes in these cases.
(At the moment, we always enable the wireless and 3G control. In the case
of the former, this is fairly safe. In the case of the latter though,
trying to toggle this device if it doesn't exist on a laptop causes ACPI
warnings/ errors).
To summarise: If you have an Acer laptop with a built in 3G card, please
report back the value from this file.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Carlos Corbacho [Sat, 21 Jun 2008 08:09:48 +0000 (09:09 +0100)]
acer-wmi: Disable device autodetection on Fujitsu Siemens Amilo Li2732
The AMW0 (V1) device detection method doesn't work properly on this laptop,
so disable it, and for other laptops that may have this problem, by
switching on a strange GUID.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Carlos Corbacho [Sat, 21 Jun 2008 08:09:38 +0000 (09:09 +0100)]
acer-wmi: Add EC quirk for Fujitsu Siemens Amilo Li 1718
This laptop needs a different EC quirk from the standard Acer one to read
the wireless status.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Carlos Corbacho [Sat, 21 Jun 2008 08:09:27 +0000 (09:09 +0100)]
acer-wmi: Respect framebuffer blanking in backlight
If the framebuffer has requested blanking, turn the backlight down. Also
offer the user the option to do this.
Reported-by: Michal Pecio <michal.pecio@gmail.com> Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Carlos Corbacho [Sat, 21 Jun 2008 08:09:22 +0000 (09:09 +0100)]
acer-wmi: Blacklist backlight on Acer Aspire 1520 & 1360 series
A newer BIOS for these laptops adds ACPI-WMI support to them. However, it does
not add support for the backlight via the EC, and we have no way to detect
this on older machines, so blacklist it from them.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Carlos Corbacho [Sat, 21 Jun 2008 08:09:08 +0000 (09:09 +0100)]
acer-wmi: Remove LED colour comment from documentation
This should have been removed when the colour was removed from the LED
device name.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Bob Moore [Fri, 13 Jun 2008 00:28:55 +0000 (08:28 +0800)]
Make GPE disable more robust
Implemented another change for the GPE disable. We now perform a
read-change-write of the enable register instead of simply writing out the
cached enable mask. This will prevent inadvertent enabling of GPEs if a rogue
GPE is received during initialization (before GPE handlers are installed.)
http://bugzilla.kernel.org/show_bug.cgi?id=6217
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Yi Yang [Sat, 14 Jun 2008 04:54:37 +0000 (00:54 -0400)]
ACPI: fix processor throttling set error
http://bugzilla.kernel.org/show_bug.cgi?id=9704
When echo some invalid values to /proc/acpi/processor/*/throttling,
there isn't any error info returned, on the contray, it sets
throttling value to some T* successfully, obviously, this is incorrect,
a correct way should be to let it fail and return error info.
This patch fixed the aforementioned issue, it also enables
/proc/acpi/processor/*/throttling to accept such values as 't0' and 'T0',
it also strictly limits /proc/acpi/processor/*/throttling only to accept
"*", "t*" and "T*", "*" is the throttling state value the processor can
support, current, it is 0 - 7.
Before applying this patch, the test result is below:
[root@localhost acpi]# cat /proc/acpi/processor/CPU0/throttling
state count: 8
active state: T1
state available: T0 to T7
states:
T0: 100%
*T1: 87%
T2: 75%
T3: 62%
T4: 50%
T5: 37%
T6: 25%
T7: 12%
[root@localhost acpi]# echo "1xxxxxx" > /proc/acpi/processor/CPU0/throttling
[root@localhost acpi]# cat /proc/acpi/processor/CPU0/throttling
state count: 8
active state: T1
state available: T0 to T7
states:
T0: 100%
*T1: 87%
T2: 75%
T3: 62%
T4: 50%
T5: 37%
T6: 25%
T7: 12%
[root@localhost acpi]# echo "0" > /proc/acpi/processor/CPU0/throttling
[root@localhost acpi]# cat /proc/acpi/processor/CPU0/throttling
state count: 8
active state: T0
state available: T0 to T7
states:
*T0: 100%
T1: 87%
T2: 75%
T3: 62%
T4: 50%
T5: 37%
T6: 25%
T7: 12%
[root@localhost acpi]# cd /
[root@localhost /]# cat /proc/acpi/processor/CPU0/throttling
state count: 8
active state: T0
state available: T0 to T7
states:
*T0: 100%
T1: 87%
T2: 75%
T3: 62%
T4: 50%
T5: 37%
T6: 25%
T7: 12%
[root@localhost /]# echo "T0" > /proc/acpi/processor/CPU0/throttling
[root@localhost /]# cat /proc/acpi/processor/CPU0/throttling
state count: 8
active state: T0
state available: T0 to T7
states:
*T0: 100%
T1: 87%
T2: 75%
T3: 62%
T4: 50%
T5: 37%
T6: 25%
T7: 12%
[root@localhost /]# echo "T7" > /proc/acpi/processor/CPU0/throttling
[root@localhost /]# cat /proc/acpi/processor/CPU0/throttling
state count: 8
active state: T0
state available: T0 to T7
states:
*T0: 100%
T1: 87%
T2: 75%
T3: 62%
T4: 50%
T5: 37%
T6: 25%
T7: 12%
[root@localhost /]# echo "T100" > /proc/acpi/processor/CPU0/throttling
[root@localhost /]# cat /proc/acpi/processor/CPU0/throttling
state count: 8
active state: T0
state available: T0 to T7
states:
*T0: 100%
T1: 87%
T2: 75%
T3: 62%
T4: 50%
T5: 37%
T6: 25%
T7: 12%
[root@localhost /]# echo "xxx" > /proc/acpi/processor/CPU0/throttling
[root@localhost /]# cat /proc/acpi/processor/CPU0/throttling
state count: 8
active state: T0
state available: T0 to T7
states:
*T0: 100%
T1: 87%
T2: 75%
T3: 62%
T4: 50%
T5: 37%
T6: 25%
T7: 12%
[root@localhost /]# echo "2xxxx" > /proc/acpi/processor/CPU0/throttling
[root@localhost /]# cat /proc/acpi/processor/CPU0/throttling
state count: 8
active state: T2
state available: T0 to T7
states:
T0: 100%
T1: 87%
*T2: 75%
T3: 62%
T4: 50%
T5: 37%
T6: 25%
T7: 12%
[root@localhost /]# echo "" > /proc/acpi/processor/CPU0/throttling
[root@localhost /]# cat /proc/acpi/processor/CPU0/throttling
state count: 8
active state: T0
state available: T0 to T7
states:
*T0: 100%
T1: 87%
T2: 75%
T3: 62%
T4: 50%
T5: 37%
T6: 25%
T7: 12%
[root@localhost /]# echo "7777" > /proc/acpi/processor/CPU0/throttling
-bash: echo: write error: Invalid argument
[root@localhost /]# echo "7xxx" > /proc/acpi/processor/CPU0/throttling
[root@localhost /]# cat /proc/acpi/processor/CPU0/throttling
state count: 8
active state: T7
state available: T0 to T7
states:
T0: 100%
T1: 87%
T2: 75%
T3: 62%
T4: 50%
T5: 37%
T6: 25%
*T7: 12%
[root@localhost /]#
After applying this patch, the test result is below:
Yi Yang [Sat, 14 Jun 2008 04:52:06 +0000 (00:52 -0400)]
ACPI: fix acpi fan state set error
Under /proc/acpi, there is a fan control interface, a user can
set 0 or 3 to /proc/acpi/fan/*/state, 0 denotes D0 state, 3
denotes D3 state, but in current implementation, a user can
set a fan to D1 state by any char excluding '1', '2' and '3'.
Signed-off-by: Yi Yang <yi.y.yang@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com> Acked-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Jonathan Woithe [Wed, 11 Jun 2008 00:44:56 +0000 (10:14 +0930)]
Fujitsu-laptop update
Add additional capabilities to the Fujitsu-laptop driver.
* Brightness hotkey actions are sent to userspace. This can be disabled
using a module parameter if it causes issues with models which handle
these keys transparently in the BIOS.
* Actions of additional hotkeys found on some Fujitsu models (eg: the
suspend key and the dedicated "power on passphrase" keys) are broadcast
to userspace.
* An alternative brightness control method used by some Fujitsu models
(for example, the S6410) is now supported, enabling software brightness
controls on models using this method.
* DMI-based module aliases are configured for the S6410 and S7020.
* The current LCD brightness after booting should now be reflected in the
standard backlight interface sysfs file (previously it was always set to
0). The platform brightness sysfs interface has always been fine.
Thanks go to Peter Gruber who provided a significant portion of this code
and tested various iterations of the patch on his S6410.
Signed-off-by: Peter Gruber <nokos@gmx.net> Signed-off-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Mike Travis [Mon, 9 Jun 2008 23:22:23 +0000 (16:22 -0700)]
ACPI: change processors from array to per_cpu variable
Change processors from an array sized by NR_CPUS to a per_cpu variable.
Signed-off-by: Mike Travis <travis@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
This is driver for Compal Laptop: FL90/IFL90, based on MSI driver.
This driver exports a few files in /sys/devices/platform/compal-laptop/:
lcd_level - screen brightness: contains a single integer in the range 0..7 (rw)
wlan - wlan subsystem state: contains 0 or 1 (rw)
bluetooth - bluetooth subsystem state: contains 0 or 1 (rw)
raw - raw value taken from embedded controller register (ro)
In addition to these platform device attributes the driver registers itself
in the Linux backlight control subsystem and is available to userspace under
/sys/class/backlight/compal-laptop/.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com> Signed-off-by: Andi Kleen <ak@linux.intel.com> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Cc: Len Brown <lenb@kernel.org> Cc: Alexey Starikovskiy <aystarik@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com>
create sysfs link from acpi device to sysdev for cpu
Sys I/F under acpi device node and sysdev device node are both
needed for cpu hot-removal. User space need this link so that
they know they are poking the sys I/F for the same cpu.
http://bugzilla.kernel.org/show_bug.cgi?id=9772
Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
The ACPI device node for the cpu has already been unregistered
when acpi_processor_handle_eject is called.
Thus we should offline the cpu and continue, rather than a failure here.
http://bugzilla.kernel.org/show_bug.cgi?id=9772
Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
projects / linux-2.6 / log