Andrew Sharp [Wed, 31 Oct 2007 21:11:24 +0000 (14:11 -0700)]
[MIPS] Put cast inside macro instead of all the callers
Since all the callers of the PHYS_TO_XKPHYS macro call with a constant,
put the cast to LL inside the macro where it really should be rather
than in all the callers. This makes macros like PHYS_TO_XKSEG_UNCACHED
work without gcc whining.
Signed-off-by: Andrew Sharp <andy.sharp@onstor.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This complements the generic R4000/R4400 errata workaround code and adds
bits for the daddiu problem. In most places it just modifies handwritten
assembly code so that the assembler is allowed to use a temporary register
as daddiu may now be treated as a macro that expands to a sequence of li
and daddu. It is the AT register or, where AT is unavailable or used
explicitly for another purpose, an explicitly-named register is selected,
using the .set at=<reg> feature added recently to gas. This feature is
only used if CONFIG_CPU_DADDI_WORKAROUNDS has been set, so if the
workaround remains disabled, the required version of binutils stays
unchanged.
Similarly, daddiu instructions put in branch delay slots in noreorder
fragments are now taken out of them and the assembler is allowed to
reorder them itself as possible (which it does making the whole idea of
scheduling them into delay slots manually questionable).
Also in the very few places where such a simple conversion was not
possible, a handcoded longer sequence is implemented.
Other than that there are changes to code responsible for building the
TLB fault and page clear/copy handlers to avoid daddiu as appropriate.
These are only effective if the erratum is verified to be present at the
run time.
Finally there is a trivial update to __delay(), because it uses daddiu in
a branch delay slot.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is the gereric part of R4000/R4400 errata workarounds. They include
compiler and assembler support as well as some source code modifications
to address the problems with some combinations of multiply/divide+shift
instructions as well as the daddi and daddiu instructions.
Changes included are as follows:
1. New Kconfig options to select workarounds by platforms as necessary.
2. Arch top-level Makefile to pass necessary options to the compiler; also
incompatible configurations are detected (-mno-sym32 unsupported as
horribly intrusive for little gain).
3. Bug detection updated and shuffled -- the multiply/divide+shift problem
is lethal enough that if not worked around it makes the kernel crash in
time_init() because of a division by zero; the daddiu erratum might
also trigger early potentially, though I have not observed it. On the
other hand the daddi detection code requires the exception subsystem to
have been initialised (and is there mainly for information).
4. r4k_daddiu_bug() added so that the existence of the erratum can be
queried by code at the run time as necessary; useful for generated code
like TLB fault and copy/clear page handlers.
5. __udelay() updated as it uses multiplication in inline assembly.
Note that -mdaddi requires modified toolchain (which has been maintained
by myself and available from my site for ~4years now -- versions covered
are GCC 2.95.4 - 4.1.2 and binutils from 2.13 onwards). The -mfix-r4000
and -mfix-r4400 have been standard for a while though.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (197 commits)
sh: add spi header and r2d platform data V3
sh: update r7780rp interrupt code
sh: remove consistent alloc stuff from the machine vector
sh: use declared coherent memory for dreamcast pci ethernet adapter
sh: declared coherent memory support V2
sh: Add support for SDK7780 board.
sh: constify function pointer tables
sh: Kill off -traditional for linker script.
cdrom: Add support for Sega Dreamcast GD-ROM.
sh: Kill off hs7751rvoip reference from arch/sh/Kconfig.
sh: Drop r7780rp_defconfig, use r7780mp_defconfig as kbuild default.
sh: Kill off dead HS771RVoIP board support.
sh: r7785rp: Fix up DECLARE_INTC_DESC() arg mismatch.
sh: r7785rp: Hook up the rest of the HL7785 FPGA IRQ vectors.
sh: r2d - enable sm501 usb host function
sh: remove voyagergx
sh: r2d - add lcd planel timings to sm501 platform data
sh: Add OHCI and UDC platform devices for SH7720.
sh: intc - remove default interrupt priority tables
sh: Correct pte size mismatch for X2 TLB.
...
Linus Torvalds [Mon, 28 Jan 2008 21:52:20 +0000 (08:52 +1100)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (24 commits)
HID: ADS/Tech Radio si470x needs blacklist entry
HID: Logitech Extreme 3D needs NOGET quirk
HID: Refactor MS Presenter 8K key mapping
HID: MS Presenter mapping for PID 0x0701
HID: Support Samsung IR remote
HID: fix compilation of hidbp drivers without usbhid
HID: Blacklist the Gretag-Macbeth Huey display colorimeter
HID: the `bit' in hidinput_mapping_quirks() is an out parameter
HID: remove redundant WARN_ON()s in order not to scare users
HID: force hiddev creation for SONY PS3 controller
HID: Use hid blacklist in usbmouse/usbkbd
HID: proper handling of MS 4k and 6k devices
HID: remove unused variable in quirk event handler
HID: hid-input quirk for BTC 8193
HID: separate hid-input event quirks from generic code
HID: refactor mapping to input subsystem for quirky devices
HID: Microsoft Wireless Optical Desktop 3.0 quirk
HID: Add support for Logitech Elite keyboards
HID: add full support for Genius KB-29E
HID: fix a potential bug in pointer casting
...
Linus Torvalds [Mon, 28 Jan 2008 21:51:05 +0000 (08:51 +1100)]
Merge branch 'sg' of git://git.kernel.dk/linux-2.6-block
* 'sg' of git://git.kernel.dk/linux-2.6-block:
SG: work with the SCSI fixed maximum allocations.
SG: Convert SCSI to use scatterlist helpers for sg chaining
SG: Move functions to lib/scatterlist.c and add sg chaining allocator helpers
Tobias Lorenz [Sun, 27 Jan 2008 21:19:22 +0000 (22:19 +0100)]
HID: ADS/Tech Radio si470x needs blacklist entry
This patch adds blacklist entries in hid-quirks.c to let the usbhid driver
ignore the si470x radio devices. They are now handled by the new radio-si470x
driver.
Jan Kiszka [Mon, 14 Jan 2008 12:08:27 +0000 (13:08 +0100)]
HID: Refactor MS Presenter 8K key mapping
Following the suggestion of Jonas, this patch maps the special keys of
the MS Presenter 8000 to targets that should allow for better re-mapping
according to individual use cases (i.e. I avoided hard-wiring to
standard keys). This time I also included the last missing key event
(switching back from presentation mode).
The optimal Xmodmap customization for using the Presenter with
OpenOffice now looks like this for me:
keycode 175 = Escape
keycode 179 = F5
keysym XF86Forward = Right
keysym XF86Back = Left
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Robert Schedel [Tue, 25 Dec 2007 23:57:40 +0000 (00:57 +0100)]
HID: Support Samsung IR remote
Samsung USB remotes (0419:0001) are rejected by kernel 2.6.23, because the
report descriptor from the remote contains a 48 bit HID report field. HID 1.11
states: Fields may span at most 4 bytes.
This patch, based on 2.6.23, fixes this by modifying the internal report
descriptor in hid-quirks.c. Additional user space support (e.g. LIRC) is
required to fetch the information from the hiddev interface.
The burden to reconstruct the data is moved into userspace (lirc through hiddev).
There is no need to set HID_QUIRK_HIDDEV quirk, as the device has also output
applications, which trigger the creation of hiddev device automatically.
Signed-off-by: Robert Schedel <r.schedel@yahoo.de> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Nicolas Mailhot [Sun, 16 Dec 2007 17:16:43 +0000 (18:16 +0100)]
HID: Blacklist the Gretag-Macbeth Huey display colorimeter
The Gretag-Macbeth Huey display colorimeter claims to be an HID device but
isn't. As a result the linux HID device will claim it, preventing FLOSS
software like Argyll CMS from talking to it.
Jiri Kosina [Fri, 30 Nov 2007 10:12:58 +0000 (11:12 +0100)]
HID: remove redundant WARN_ON()s in order not to scare users
The WARN_ON() in implement() and extract() spit out stacktraces and
a lot of other information that might make users think that there is
something seriously wrong with the system. WARN_ON() should not be
deliberately triggerable by userspace application, which these can be.
Usually this WARN_ON() triggers when hid2hci utility is sending the
data that don't correspond to the device's report descriptor.
Bastien Nocera [Wed, 28 Nov 2007 15:34:53 +0000 (16:34 +0100)]
HID: force hiddev creation for SONY PS3 controller
The device is not discoverable, and needs to be poked to set its master, the
Bluetooth device it will try to connect to when the "Home" button is pressed
without a cable plugged in.
Using libusb means disconnecting the device from its driver to get the report
descriptor. Using hiddev, we can poke it without relinquishing control over it,
so when you plug it in, it would still work as a pad.
This could be then used by sixpair program, after it is rewritten to use
hiddev instead of libusb.
Jiri Kosina [Mon, 26 Nov 2007 12:18:00 +0000 (13:18 +0100)]
HID: hid-input quirk for BTC 8193
BTC 8193 keyboard handles its scrollwheel in very non-standard way.
It produces two non-standard usages for scrolling up and down, in
both cases with postive value equaling to 1. We handle this by temporary
mapping, which we then catch in quirk event handler, and remap to
negative HWHEEL even in order to introduce correct behavior.
Also the button requires special mapping, as it triggers standard-violating
usage code.
Reported in kernel.org bugzilla #9385
Reported-by: Kir Kolyshkin <kir@sacred.ru> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jiri Kosina [Fri, 23 Nov 2007 12:16:02 +0000 (13:16 +0100)]
HID: separate hid-input event quirks from generic code
This patch separates also the hid-input quirks that have to be
applied at the time the event occurs, so that the generic code
handling HUT-compliant devices is not messed up by them too much.
Jiri Kosina [Thu, 22 Nov 2007 14:18:18 +0000 (15:18 +0100)]
HID: refactor mapping to input subsystem for quirky devices
Currently, the handling of mapping between hid and input for devices
that don't conform to HUT 1.12 specification is very messy -- no per-device
handling, no blacklists, conditions on idVendor and idProduct placed
all over the code.
This patch moves all the device-specific input mapping to a separate
file, and introduces a blacklist-style handling for non-standard
device-specific mappings.
Drew Fisher [Sun, 18 Nov 2007 11:29:56 +0000 (12:29 +0100)]
HID: Microsoft Wireless Optical Desktop 3.0 quirk
Make the Microsoft Wireless Optical Desktop 3.0 work as a mouse.
Microsoft Wireless Optical Desktop 3.0 doesn't properly describe its interface
class. Specifically, since it doesn't mark the second interface as a mouse
(bInterfaceSubclass = 0), it doesn't get HID_QUIRK_NOGET applied to the
interface, and then acts broken when polled.
Jiri Kosina [Wed, 14 Nov 2007 11:13:26 +0000 (12:13 +0100)]
HID: add full support for Genius KB-29E
Genius KB-29E has broken report descriptor, which causes some of the
Consumer usages to appear incorrectly as Button usages. We fix it by
fixing the report descriptor before it is being parsed.
Also a few of the keys violate the HUT standard, so they need a special
handling. They currently fall into "Reserved" range as per HUT 1.12.
Li Zefan [Wed, 14 Nov 2007 10:31:05 +0000 (11:31 +0100)]
HID: fix a potential bug in pointer casting
Don't directly cast list_head * to foo *, this works only when list
is the first member of struct foo, and we should not make the assumption
how members are ordered in the structure.
i.e. struct *f = (struct *f)pos will work if:
struct foo {
struct list_head list;
int i;
};
but will fail if:
struct foo {
int i;
struct list_head list;
}
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pavel Troller [Mon, 29 Oct 2007 10:13:46 +0000 (11:13 +0100)]
HID: Implement horizontal wheel handling for A4 Tech X5-005D
This mouse distinguishes horizontal wheel from vertical by a special "pseudo
event" GenericDesktop.00b8, with values of 0 for vertical and 8 for horizontal
wheel. Because this event is supplied by the parser too late, we need to delay
a wheel event, wait for this one and send either REL_WHEEL or REL_HWHEEL to
input depending on the event value.
Signed-off-by: Pavel Troller <patrol@sinus.cz> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jan Kiszka [Wed, 24 Oct 2007 14:24:22 +0000 (16:24 +0200)]
HID: Map MS Presenter 8000 bottom-side buttons
The MS Presenter 8000 bluetooth mouse is a "dual-use" device: If you
press a button on the top, you can turn it around and find special keys
on the other side, useful for presentations. This patch maps those three
bottom-keys that are not already detected to the intended functions. The
magic bottom on the top is mapped to F5 when we switch from mouse to
presenter mode in order to activate the presentation mode in the related
software (e.g. OpenOffice).
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Russell King [Mon, 28 Jan 2008 13:21:30 +0000 (13:21 +0000)]
Merge branch 'orion' into devel
* orion: (26 commits)
[ARM] Orion: implement power-off method for QNAP TS-109/209
[ARM] Orion: add support for QNAP TS-109/TS-209
[ARM] Orion: I2C support
[I2C] i2c-mv64xxx: Don't set i2c_adapter.retries
[I2C] Split mv643xx I2C platform support
[ARM] Orion: enable CONFIG_RTC_DRV_M41T80 for D-Link DNS-323
[ARM] Orion defconfig
[ARM] Orion: add support for Orion/MV88F5181 based D-Link DNS-323
[ARM] Orion: MV88F5181 support bits
[ARM] Orion: Buffalo/Revogear Kurobox Pro support
[ARM] OrionNAS RD board support
[ARM] Orion: support for Marvell Orion-2 (88F5281) Development Board
[ARM] Orion: common platform setup for Gigabit Ethernet port
[ARM] Orion: platform device registration for UART, USB and NAND
[ARM] Orion: system timer support
[ARM] Orion edge GPIO IRQ support
[ARM] Orion: IRQ support
[ARM] Orion: provide GPIO method for enabling hardware assisted blinking
[ARM] Orion: GPIO support
[ARM] Orion: programable address map support
...
Conflicts:
arch/arm/Kconfig
arch/arm/Makefile
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* kprobes:
ARM kprobes: let's enable it
ARM kprobes: special hook for the kprobes breakpoint handler
ARM kprobes: prevent some functions involved with kprobes from being probed
ARM kprobes: don't let a single-stepped stmdb corrupt the exception stack
ARM kprobes: add the kprobes hook to the page fault handler
ARM kprobes: core code
ARM kprobes: instruction single-stepping support
* ks8695:
[ARM] 4603/1: KS8695: debugfs interface to view pin state
[ARM] 4601/1: KS8695: PCI support
* misc:
[ARM] remove duplicate includes
[ARM] CONFIG_DEBUG_STACK_USAGE
[ARM] 4689/1: small comment wrap fix
[ARM] 4687/1: Trivial arch/arm/kernel/entry-common.S comment fix
[ARM] 4666/1: ixp4xx: fix sparse warnings in include/asm-arm/arch-ixp4xx/io.h
[ARM] remove reference to non-existent MTD_OBSOLETE_CHIPS
[SERIAL] 21285: Report baud rate back via termios
[ARM] Remove pointless casts from void pointers,
[ARM] Misc minor interrupt handler cleanups
[ARM] Remove at91_lcdc.h
[ARM] ARRAY_SIZE() cleanup
[ARM] Update mach-types
* msm:
[ARM] msm: dma support for MSM7X00A
[ARM] msm: board file for MACH_HALIBUT (QCT MSM7200A)
[ARM] msm: irq and timer support for ARCH_MSM7X00A
[ARM] msm: core platform support for ARCH_MSM7X00A
* s3c2410: (33 commits)
[ARM] 4795/1: S3C244X: Add armclk and setparent call
[ARM] 4794/1: S3C24XX: Comonise S3C2440 and S3C2442 clock code
[ARM] 4793/1: S3C24XX: Add IRQ->GPIO pin mapping function
[ARM] 4792/1: S3C24XX: Remove warnings from debug-macro.S
[ARM] 4791/1: S3C2412: Make fclk a parent of msysclk
[ARM] 4790/1: S3C2412: Fix parent selection for msysclk.
[ARM] 4789/1: S3C2412: Add missing CLKDIVN register values
[ARM] 4788/1: S3C24XX: Fix paramet to s3c2410_dma_ctrl if S3C2410_DMAF_AUTOSTART used.
[ARM] 4787/1: S3C24XX: s3c2410_dma_request() should return the allocated channel number
[ARM] 4786/1: S3C2412: Add SPI FIFO controll constants
[ARM] 4785/1: S3C24XX: Add _SHIFT definitions for S3C2410_BANKCON registers
[ARM] 4784/1: S3C24XX: Fix GPIO restore glitches
[ARM] 4783/1: S3C24XX: Add s3c2410_gpio_getpull()
[ARM] 4782/1: S3C24XX: Define FIQ_START for any FIQ users
[ARM] 4781/1: S3C24XX: DMA suspend and resume support
[ARM] 4780/1: S3C2412: Allow for seperate DMA channels for TX and RX
[ARM] 4779/1: S3C2412: Add s3c2412_gpio_set_sleepcfg() call
[ARM] 4778/1: S3C2412: Add armclk and init from DVS state
[ARM] 4777/1: S3C24XX: Ensure clk_set_rate() checks the set_rate method for the clk
[ARM] 4775/1: s3c2410: fix compilation error if only s3c2442 cpu is selected
...
* sa1100:
[ARM] sa1100: add clock source support
* vfp:
[ARM] 4584/2: ARMv7: Add Advanced SIMD (NEON) extension support
[ARM] 4583/1: ARMv7: Add VFPv3 support
[ARM] 4582/2: Add support for the common VFP subarchitecture
Ben Dooks [Mon, 28 Jan 2008 12:01:35 +0000 (13:01 +0100)]
[ARM] 4795/1: S3C244X: Add armclk and setparent call
Add armclk to the supported clocks on the S3C2440 and S3C2442 to
better represent the DVS state which controls whether FCLK or HCLK
is fed to the ARM core.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ben Dooks [Mon, 28 Jan 2008 12:01:24 +0000 (13:01 +0100)]
[ARM] 4784/1: S3C24XX: Fix GPIO restore glitches
The core resume code may have caused glitches in the GPIO when
restoring the GPIO state due to the order in which the GPIO registers
were being written.
Change the restore process take into account the state of the
GPIOs on resume and the state the system wants to restore them to.
See the code comments in the patch for more details of the process.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ben Dooks [Mon, 28 Jan 2008 12:01:21 +0000 (13:01 +0100)]
[ARM] 4781/1: S3C24XX: DMA suspend and resume support
If an DMA channel was active at suspend, then ensure that
it is correctly reconfigured when the system resumes.
Note, the previous policy was for each driver to handle their
own reconfiguration on resume. The policy has been changed to
make the individual driver's job easier.
Signed-off-by: Ben Dooks <ben-linux@flfuf.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ben Dooks [Mon, 28 Jan 2008 12:01:20 +0000 (13:01 +0100)]
[ARM] 4780/1: S3C2412: Allow for seperate DMA channels for TX and RX
The current S3C24XX DMA code does not allow for an peripheral
that has one channel for RX and another for TX.
This patch adds a per-cpu dma operation to select the transmit
or receive channel, and adds support to the S3C2412 for the
seperate DMA channels for TX and RX.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ben Dooks [Mon, 28 Jan 2008 12:01:17 +0000 (13:01 +0100)]
[ARM] 4777/1: S3C24XX: Ensure clk_set_rate() checks the set_rate method for the clk
Add checks for clk_set_rate() and ensure that we do not allow set_rate
to be called for a clock that does not have it defined. Add default
methods for fclk, hclk, pclk and mpll.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We have a default display set to 4, when we only have
three registered displays. Fix this argument (a seperate
patch has been generated to ensure that the LCD driver
takes notice of this bug)
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ben Dooks [Sun, 23 Dec 2007 02:09:32 +0000 (03:09 +0100)]
[ARM] 4722/1: S3C24XX: Improve output if watchdog reset fails
If the watchdog reset fails and we decided to take the jump
to zero approach, allow 50ms for the UARTS to drain the FIFOs
before calling into a bootloader that may flush the output.
Also reduece the waits and the timeout values as 5 seconds is
rather long.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Daniel Mack [Wed, 23 Jan 2008 13:54:50 +0000 (14:54 +0100)]
[ARM] 4762/1: Basic support for Toradex Colibri module
This patch adds support for Toradex' PXA27x based Colibri module.
It's kept as simple as possible to only provide basic functionality.
A default config is also included.
Signed-off-by: Daniel Mack <daniel@caiaq.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Wed, 23 Jan 2008 14:05:58 +0000 (14:05 +0000)]
[ARM] pxa: fix mci_init functions returning -1
Fix all those PXA mci_init functions which return -1 rather than
propagating the error code to the higher levels. Remove the silly
set_irq_type() calls as well - use the flags for request_irq()
instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Richard Purdie [Wed, 2 Jan 2008 00:09:54 +0000 (01:09 +0100)]
[ARM] 4737/1: Refactor corgi_lcd to improve readability + bugfix
This patch refactors the code in corgi_lcd.c moving it to the board
specific corgi and spitz files where appropriate instead of the
existing ifdef mess which hinders readability.
Fix spitz_get_hsync_len() to call get_hsync_invperiod so pxafb can be
compiled as a module.
The confusing variables which represent the inverse horizintal sync
period are renamed to "invperiod" consistently.
An incorrect comment in corgi_ts.c is also corrected.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Robert Schwebel [Tue, 8 Jan 2008 07:52:04 +0000 (08:52 +0100)]
[ARM] 4747/1: pcm027: support for pcm990 baseboard for phyCORE-PXA270
This patch adds baseboard support for the phyCORE-PXA270 development
kit (aka PCM-990).
This example shows how to use some phyCORE-PXA270 CPU module features
on a baseboard in a standard manner. It could be used as a starting
point for custom baseboard development.
V2:
After comments by Eric Miao:
- IRQ chained handler fixed
- video/graphic support moved to separate patch
- ifdef/endif hell reduced ;-)
V3:
After comments by Russell King
- initialise the mmci platform data statically
V4:
After comments by Russell King
- wrong return value in pcm990_mci_init() fixed
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Robert Schwebel [Tue, 8 Jan 2008 07:44:23 +0000 (08:44 +0100)]
[ARM] 4744/1: pcm027: add support for phyCORE-PXA270 CPU module
This patch adds main support for the generic phyCORE-PXA270 CPU module
(aka PCM-027). Its as generic as possible to support any kind of baseboard.
Note: Neither the CPU module nor the pcm027.c implementation can work without
a baseboard support. Baseboard support can be added by the PCM-990 or any
custom variant.
V2:
After comments by Eric Miao:
- Currently unsupported devices moved into separate patch
- direct call of baseboard initialisation
V3:
After comments by Russell King
- sort include files
- setting RTC bit for power control removed
- style problems fixed (discovered by checkpatch.pl)
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Mon, 14 Jan 2008 22:30:10 +0000 (22:30 +0000)]
[NET] smc91x: Make smc91x use IRQ resource trigger flags
smc91x is shared between many different platforms. Each platform needs
to specify the interrupt type, and in some cases the irq type depends
on more than just the build configuration - it depends on runtime
checks.
Rather than throwing this code into the SMC_IRQ_FLAGS definition, provide
a way for these flags to be passed via the IRQ resource itself.
Note that IRQF_TRIGGER_* constants are intentionally defined to correspond
with the IORESOURCE_IRQ_* interrupt type flags, in much the same way that
the low bits of PCI iomem resources correspond with the BAR flag bits.
Also provide a way to configure smc91x to read the IRQ flags from the
resource. Once all platforms have been converted over (signified
by all definitions of SMC_IRQ_FLAGS being -1) SMC_IRQ_FLAGS should
be removed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Acked-by: Nicolas Pitre <nico@cam.org> Acked-by: Jeff Garzik <jgarzik@redhat.com>
Jens Axboe [Mon, 28 Jan 2008 10:38:15 +0000 (11:38 +0100)]
cfq-iosched: relax IOPRIO_CLASS_IDLE restrictions
Currently you must be root to set idle io prio class on a process. This
is due to the fact that the idle class is implemented as a true idle
class, meaning that it will not make progress if someone else is
requesting disk access. Unfortunately this means that it opens DOS
opportunities by locking down file system resources, hence it is root
only at the moment.
This patch relaxes the idle class a little, by removing the truly idle
part (which entals a grace period with associated timer). The
modifications make the idle class as close to zero impact as can be done
while still guarenteeing progress. This means we can relax the root only
criteria as well.
Move the xtime write mode seqlock into timer_tick(), so it only
surrounds the call to do_timer().
This avoids a deadlock in update_process_times() ...
hrtimer_get_softirq_time() which tries to get a read mode seqlock
on xtime, thereby preventing booting.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
projects / linux-2.6 / log