Johannes Berg [Tue, 13 May 2008 03:48:31 +0000 (20:48 -0700)]
net: Allow netdevices to specify needed head/tailroom
This patch adds needed_headroom/needed_tailroom members to struct
net_device and updates many places that allocate sbks to use them. Not
all of them can be converted though, and I'm sure I missed some (I
mostly grepped for LL_RESERVED_SPACE)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Helmut Schaa [Thu, 8 May 2008 11:34:07 +0000 (13:34 +0200)]
mac80211: fix association with some APs
Some APs refuse association if the supported rates contained in the
association request do not match its own supported rates. This patch
introduces a new function which builds the intersection between the AP's
supported rates and the client's supported rates to work around such
problems. The same approach is already used in ipw2200 for example.
Signed-off-by: Helmut Schaa <hschaa@suse.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in RX path, the frequency was wrongly set in the
ieee80211_rx_status. This bug led to an empty scan list in A band.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 7 May 2008 23:43:59 +0000 (01:43 +0200)]
zd1211rw: fix potential use-after-free bug
zd_mac_tx_to_dev() could potentially free the skb, or hand it off
to mac80211 which might free it. Hence, this code needs to get the
usb pointer out of skb->cb before handing it off to that function.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Emelyanov [Tue, 6 May 2008 14:46:36 +0000 (18:46 +0400)]
Fix GFP_KERNEL allocation under read lock.
The mesh_path_add() read-locks the pathtbl_resize_lock and calls
kmalloc with GFP_KERNEL mask.
Fix it and move the endadd2 label lower. It should be _before_ the
if() beyond, but it makes no sense for it being there, so I move it
right after this if().
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Without this patch, if xmit_skb is null but net_ratelimit() returns 0 we would
go to the else branch and access the null xmit_skb. Pointed out by Johannes
Berg.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 5 May 2008 18:40:35 +0000 (20:40 +0200)]
mac80211: Don't encrypt beacons
mac80211 should set the IEEE80211_TX_CTL_DO_NOT_ENCRYPT flag in tx_control
structure to inform drivers not to encrypt the beacon. Drivers that only check
for that flag before accessing the hw_key field, will otherwise cause a NULL
pointer dereference since that field is not configured for beacons.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 5 May 2008 15:24:03 +0000 (17:24 +0200)]
rt2x00: Clean up error handling of PCI queue DMA allocation.
When, for some reason, the rt2x00pci module fails to allocate DMA memory for
the queues, it tries to undo the complete initialization of the PCI device,
including freeing of the irq. This results in the following error in dmesg, as
the irq hadn't been requested yet:
[ 78.123456] Trying to free already-free IRQ 17
Fix this by implementing proper error handling code, instead of just using the
full uninitialization function.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 5 May 2008 15:23:47 +0000 (17:23 +0200)]
rt2x00: Fix broken recover-on-error path
During initialization the initialize() callback function
in rt2x00pci and rt2x00usb will cleanup the mess they made.
rt2x00lib shouldn't call uninitialize because the callback function already
cleaned up _and_ the DEVICE_INITIALIZED isn't set which causes the
rt2x00lib_uninitialize() to halt directly anyway. All that is required
to be cleaned up by rt2x00lib is the queue, and that can be done by
calling rt2x00queue_uninitialize() directly.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 5 May 2008 15:23:31 +0000 (17:23 +0200)]
rt2x00: Don't use pskb_expand_head()
rt2x00pci allocates DMA for descriptor and data,
rt61pci doesn't use this for the beacon, but it can
use the descriptor part as temporary buffer instead
of using pskb_expand_head().
Using this temporary buffer is obviously much better
then reallocating the skb buffer...
At the same time we can set the data length for the
beacon queue at 0, to make sure no DMA is allocated for
data (but just for the descriptor).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 2 May 2008 23:04:47 +0000 (01:04 +0200)]
mac80211: fix debugfs default key oops
Under certain circumstances (in AP mode) the debugfs function
that is supposed to add the default key symlink can encounter
a NULL default_key pointer. This patch makes it handle that
situtation gracefully.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Steven Rostedt [Thu, 1 May 2008 22:58:17 +0000 (15:58 -0700)]
fix irq flags in mac80211 code
A file in the net/mac80211 directory uses "int" for flags. This can cause
hard to find bugs on some architectures. This patch converts the flags to use
"long" instead.
This bug was discovered by doing an allyesconfig make on the -rt kernel where
checks are done to ensure all flags are of size sizeof(long).
Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
prism54: fix regression with missing carrier in AP-mode
This fixes a regression introduced by commit 7b463ced6 (prism54: set
carrier flags correctly) which causes the device to come up without
a carrier in AP-mode.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Julia Lawall [Mon, 12 May 2008 22:43:46 +0000 (15:43 -0700)]
pppol2tp: Remove null pointer dereference.
If session is NULL, it is not possible to access its name field. So I
have split apart the printing of the error message to drop the
printing of the name field in this case.
The macro PRINTK actually only evaluates its arguments starting with
the third one if the bitwise conjunction of the first two is non-zero.
Normally, this conjunction would only be non-zero if debugging mode
were turned on, but when session is NULL, the first argument in both
the old and new code is -1, and thus the bitwise conjunction is true.
Perhaps a different strategy is desired, such as using tunnel->debug,
which session->debug is initialized to, but tunnel can also be NULL,
so this does not completely solve the problem.
This problem was found using the following semantic match
(http://www.emn.fr/x-info/coccinelle/)
David S. Miller [Mon, 12 May 2008 10:29:11 +0000 (03:29 -0700)]
syncppp: Fix crashes.
The syncppp layer wants a mid-level netdev private pointer.
It was using netdev->priv but that only worked by accident,
and thus this scheme was broken when the device private
allocation strategy changed.
Add a proper mid-layer private pointer for uses like this,
update syncppp and all users, and remove the HDLC_PPP broken
tag from drivers/net/wan/Kconfig
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Fri, 9 May 2008 22:11:53 +0000 (15:11 -0700)]
sctp: Add address type check while process paramaters of ASCONF chunk
If socket is create by AF_INET type, add IPv6 address to asoc will cause
kernel panic while packet is transmitted on that transport.
This patch add address type check before process paramaters of ASCONF
chunk. If peer is not support this address type, return with error
invald parameter.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Fri, 9 May 2008 22:11:17 +0000 (15:11 -0700)]
sctp: Do not enable peer IPv6 address support on PF_INET socket
If socket is create by PF_INET type, it can not used IPv6 address to
send/recv DATA, So we can not used IPv6 address even if peer tell us it
support IPv6 address.
This patch fix to only enabled peer IPv6 address support on PF_INET6 socket.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matheos Worku [Mon, 12 May 2008 10:10:59 +0000 (03:10 -0700)]
niu: Determine the # of ports from the card's VPD data
Determine the number of physical ports from the card's VPD data.
Previous fix failed on Maramba platform which doesn't have the
"board-model" property. This fix uses the "model" property which
exists on all cards and Neptune based motherboards.
cstyle cleanup included.
Signed-off-by: Matheos Worku <matheos.worku@sun.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Hartkopp [Thu, 8 May 2008 09:49:55 +0000 (02:49 -0700)]
can: Fix can_send() handling on dev_queue_xmit() failures
The tx packet counting and the local loopback of CAN frames should
only happen in the case that the CAN frame has been enqueued to the
netdevice tx queue successfully.
Thanks to Andre Naujoks <nautsch@gmail.com> for reporting this issue.
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net> Signed-off-by: Urs Thuermann <urs@isnogud.escape.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Thu, 8 May 2008 08:24:25 +0000 (01:24 -0700)]
netns: Fix arbitrary net_device-s corruptions on net_ns stop.
When a net namespace is destroyed, some devices (those, not killed
on ns stop explicitly) are moved back to init_net.
The problem, is that this net_ns change has one point of failure -
the __dev_alloc_name() may be called if a name collision occurs (and
this is easy to trigger). This allocator performs a likely-to-fail
GFP_ATOMIC allocation to find a suitable number. Other possible
conditions that may cause error (for device being ns local or not
registered) are always false in this case.
So, when this call fails, the device is unregistered. But this is
*not* the right thing to do, since after this the device may be
released (and kfree-ed) improperly. E. g. bridges require more
actions (sysfs update, timer disarming, etc.), some other devices
want to remove their private areas from lists, etc.
I. e. arbitrary use-after-free cases may occur.
The proposed fix is the following: since the only reason for the
dev_change_net_namespace to fail is the name generation, we may
give it a unique fall-back name w/o %d-s in it - the dev<ifindex>
one, since ifindexes are still unique.
So make this change, raise the failure-case printk loglevel to
EMERG and replace the unregister_netdevice call with BUG().
[ Use snprintf() -DaveM ]
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Thu, 8 May 2008 08:15:21 +0000 (01:15 -0700)]
netfilter: nf_conntrack_sip: restrict RTP expect flushing on error to last request
Some Inovaphone PBXs exhibit very stange behaviour: when dialing for
example "123", the device sends INVITE requests for "1", "12" and
"123" back to back. The first requests will elicit error responses
from the receiver, causing the SIP helper to flush the RTP
expectations even though we might still see a positive response.
Note the sequence number of the last INVITE request that contained a
media description and only flush the expectations when receiving a
negative response for that sequence number.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Thu, 8 May 2008 08:13:31 +0000 (01:13 -0700)]
macvlan: Fix memleak on device removal/crash on module removal
As noticed by Ben Greear, macvlan crashes the kernel when unloading the
module. The reason is that it tries to clean up the macvlan_port pointer
on the macvlan device itself instead of the underlying device. A non-NULL
pointer is taken as indication that the macvlan_handle_frame_hook is
valid, when receiving the next packet on the underlying device it tries
to call the NULL hook and crashes.
Clean up the macvlan_port on the correct device to fix this.
Signed-off-by; Patrick McHardy <kaber@trash.net> Tested-by: Ben Greear <greearb@candelatech.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: J.H.M. Dassen (Ray) <jdassen@debian.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Thu, 8 May 2008 08:09:11 +0000 (01:09 -0700)]
tcp FRTO: SACK variant is errorneously used with NewReno
Note: there's actually another bug in FRTO's SACK variant, which
is the causing failure in NewReno case because of the error
that's fixed here. I'll fix the SACK case separately (it's
a separate bug really, though related, but in order to fix that
I need to audit tp->snd_nxt usage a bit).
There were two places where SACK variant of FRTO is getting
incorrectly used even if SACK wasn't negotiated by the TCP flow.
This leads to incorrect setting of frto_highmark with NewReno
if a previous recovery was interrupted by another RTO.
An eventual fallback to conventional recovery then incorrectly
considers one or couple of segments as forward transmissions
though they weren't, which then are not LOST marked during
fallback making them "non-retransmittable" until the next RTO.
In a bad case, those segments are really lost and are the only
one left in the window. Thus TCP needs another RTO to continue.
The next FRTO, however, could again repeat the same events
making the progress of the TCP flow extremely slow.
In order for these events to occur at all, FRTO must occur
again in FRTOs step 3 while the key segments must be lost as
well, which is not too likely in practice. It seems to most
frequently with some small devices such as network printers
that *seem* to accept TCP segments only in-order. In cases
were key segments weren't lost, things get automatically
resolved because those wrongly marked segments don't need to be
retransmitted in order to continue.
I found a reproducer after digging up relevant reports (few
reports in total, none at netdev or lkml I know of), some
cases seemed to indicate middlebox issues which seems now
to be a false assumption some people had made. Bugzilla
#10063 _might_ be related. Damon L. Chesser <damon@damtek.com>
had a reproducable case and was kind enough to tcpdump it
for me. With the tcpdump log it was quite trivial to figure
out.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
On a read error, e1000e might have returned uninitialized block of
eeprom data back to userspace. The convention is that 0xff is "empty",
so mark the entire eeprom as empty in case of an error.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 9fb1e350e16164d56990dde036ae9c0a2fd3f634,
ucc_geth: use rx-clock-name and tx-clock-name device tree properties
Introduced a typo that made the driver use the RX clock
as TX clock, causing massive TX errors.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Taken from http://bugzilla.kernel.org/show_bug.cgi?id=10577
I was unable to access a computer containing an Intel EtherExpress 16 network
card using IPv6.
I traced this to failure of neighbour discovery. When I used an "ip -6 neigh
add" command, on the computer attempting access, to insert a binding between
the IPv6 address of the computer with the Intel EtherExpress 16 network card
and the card's ethernet address, I was able to access that computer using
IPv6.
Neighbour discovery requires working multicast. The driver sources file
eexpress.c contains an approximately 30 line function eexp_setup_filter used
when loading multicast addresses.
I found 3 problems in this function
1) It wrote the number of multicast addresses to the card instead of the
number of bytes in the multicast addresses.
2) When loading multiple multicast addresses it loaded the first one
provided multiple times instead of loading each one once.
3) The setting of pointer 'data' from 'dmi->dmi_addr' occured before the
test for the error situation of 'dmi' being NULL.
Correcting these problems allows the computer with the Intel EtherExpress 16
network card to found by IPv6 neighbour discovery.
p.s. There is some information on the Intel EtherExpress 16 at
http://www.intel.com/support/etherexpress/vintage/sb/cs-013500.htm
Datasheet for the Intel 82586 ethernet controller used by the card
http://www.datasheetcatalog.com/datasheets_pdf/8/2/5/8/82586.shtml
Signed-off-by: Bruce Robson <bns_robson@hotmail.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bruce Allan [Tue, 29 Apr 2008 16:16:05 +0000 (09:16 -0700)]
e1000e: Add support for BM PHYs on ICH9
This patch adds support for the BM PHY, a new PHY model being used
on ICH9-based implementations.
This new PHY exposes issues in the ICH9 silicon when receiving
jumbo frames large enough to use more than a certain part of the
Rx FIFO, and this unfortunately breaks packet split jumbo receives.
For this reason we re-introduce (for affected adapters only) the
jumbo single-skb receive routine back so that people who do
wish to use jumbo frames on these ich9 platforms can do so.
Part of this problem has to do with CPU sleep states and to make
sure that all the wake up timings are correctly we force them
with the recently merged pm_qos infrastructure written by Mark
Gross. (See http://lkml.org/lkml/2007/10/4/400).
To make code read a bit easier we introduce a _IS_ICH flag so
that we don't need to do mac type checks over the code.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Anton Vorontsov [Tue, 29 Apr 2008 15:53:18 +0000 (19:53 +0400)]
uli526x: fix endianness issues in the setup frame
This patch fixes uli526x driver's issues on a PowerPC boards: uli chip
is unable to receive the packets.
It appears that send_frame_filter prepares the setup frame in the
endianness unsafe manner. On a big endian machines we should shift
the address nibble by two bytes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Anton Vorontsov [Tue, 29 Apr 2008 15:53:13 +0000 (19:53 +0400)]
uli526x: initialize the hardware prior to requesting interrupts
The firmware on MPC8610HPCD boards enables ULI ethernet and leaves it
in some funky state before booting Linux. For drivers, it's always good
idea to (re)initialize the hardware prior to requesting interrupts.
Andy Fleming [Fri, 2 May 2008 18:01:23 +0000 (13:01 -0500)]
ucc_geth: Fix a bunch of sparse warnings
ucc_geth didn't have anything marked as __iomem. It was also inconsistent
with its use of in/out accessors (using them sometimes, not using them other
times). Cleaning this up cuts the warnings down from hundreds to just over a
dozen.
Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Andy Fleming [Fri, 2 May 2008 18:00:30 +0000 (13:00 -0500)]
gianfar: Fix a locking bug in gianfar's sysfs code
During sparse cleanup, found a locking bug. Some of the sysfs functions were
acquiring a lock, and then returning in the event of an error. We rearrange
the code so that the lock is released in error conditions, too.
Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
bonding / ipv6: no addrconf for slaves separately from master
two steps were rearranged in the enslavement process: netdev_set_master
is now before the call to dev_open to open the slave.
This patch updates the error cases and unwind process at the
end of bond_enslave to match the new order. Without this patch, it is
possible for the enslavement to fail, but leave the slave with IFF_SLAVE
set in its flags.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Pavel Emelyanov [Sat, 3 May 2008 00:49:39 +0000 (17:49 -0700)]
bonding: Deadlock between bonding_store_bonds and bond_destroy_sysfs.
The sysfs layer has an internal protection, that ensures, that
all the process sitting inside ->sore/->show callback exits
before the appropriate entry is unregistered (the calltraces
are rather big, but I can provide them if required).
On the other hand, bonding takes rtnl_lock in
a) the bonding_store_bonds, i.e. in ->store callback,
b) module exit before calling the sysfs unregister routines.
Thus, the classical AB-BA deadlock may occur. To reproduce run
# while :; do modprobe bonding; rmmod bonding; done
and
# while :; do echo '+bond%d' > /sys/class/net/bonding_masters ; done
in parallel.
The fix is to move the bond_destroy_sysfs out of the rtnl_lock,
but _before_ bond_free_all to make sure no bonding devices exist
after module unload.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Acked-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Jay Vosburgh [Sat, 3 May 2008 00:49:38 +0000 (17:49 -0700)]
bonding: fix error unwind in bonding_store_bonds
Fixed an error unwind in bonding_store_bonds that didn't release
the locks it held, and consolidated unwinds into a common block at the
end of the function. Bug reported by Pavel Emelyanov <xemul@openvz.org>,
who provided a different fix.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Pavel Emelyanov [Sat, 3 May 2008 00:49:37 +0000 (17:49 -0700)]
bonding: Do not call free_netdev for already registered device.
If the call to bond_create_sysfs_entry in bond_create fails, the
proper rollback is to call unregister_netdevice, not free_netdev.
Otherwise - kernel BUG at net/core/dev.c:4057!
Checked with artificial failures injected into bond_create_sysfs_entry.
Pavel's original patch modified by Jay Vosburgh to move code around
for clarity (remove goto-hopping within the unwind block).
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Adrian Bunk [Tue, 6 May 2008 07:04:47 +0000 (00:04 -0700)]
iwlwifi: make IWLWIFI a tristate
IWLWIFI should be a tristate so that if IWLCORE and/or IWL3945 are m
and none of them is y kbuild doesn't create an empty
drivers/net/wireless/built-in.o
This patch also removes the pointless "default n".
Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Wright [Mon, 5 May 2008 20:50:24 +0000 (13:50 -0700)]
dccp: return -EINVAL on invalid feature length
dccp_feat_change() validates length and on error is returning 1.
This happens to work since call chain is checking for 0 == success,
but this is returned to userspace, so make it a real error value.
Signed-off-by: Chris Wright <chrisw@sous-sol.org> Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
the driver did not anticipate the case of !CONFIG_PNP which is rare but
still possible. Instead of restricting the driver to PNP-only in the
Kconfig space, add the (trivial) dummy struct pnp_driver - this is that
other drivers use in the !PNP case too.
The driver itself can in theory be initialized on !PNP too in certain
cases, via smsc_ircc_legacy_probe().
Patch only minimally build tested, i dont have this hardware.
Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: David S. Miller <davem@davemloft.net>
Ingo Molnar [Mon, 5 May 2008 08:04:06 +0000 (01:04 -0700)]
irda: fix !PNP support in drivers/net/irda/nsc-ircc.c
x86.git testing found the following build failure in latest -git:
drivers/built-in.o: In function `nsc_ircc_pnp_probe':
nsc-ircc.c:(.text+0xdf1b6): undefined reference to `pnp_get_resource'
nsc-ircc.c:(.text+0xdf1d4): undefined reference to `pnp_get_resource'
nsc-ircc.c:(.text+0xdf1ee): undefined reference to `pnp_get_resource'
nsc-ircc.c:(.text+0xdf237): undefined reference to `pnp_get_resource'
nsc-ircc.c:(.text+0xdf24c): undefined reference to `pnp_get_resource'
drivers/built-in.o:nsc-ircc.c:(.text+0xdf266): more undefined references to `pnp_get_resource' follow
make: *** [.tmp_vmlinux1] Error 1
while generally most users will have PNP enabled, drivers can support
non-PNP build mode too - and most drivers implement it. That is typically
done by providing a dummy pnp_driver structure that will not probe anything.
The fallback routines in the driver will handle this dumber mode of
operation too.
This patch implements that. I have not tested whether this actually
works on real hardware so take care. It does resolve the build bug.
[ Another solution that is used by a few drivers is to exclude the driver
in the Kconfig if PNP is disabled, via "depends on PNP", but this would
limit the availability of the driver needlessly. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Mon, 5 May 2008 00:59:30 +0000 (17:59 -0700)]
mac80211: Do not free net device after it is unregistered.
The error path in ieee80211_register_hw() may call the unregister_netdev()
and right after it - the free_netdev(), which is wrong, since the
unregister releases the device itself.
So the proposed fix is to NULL the local->mdev after unregister is done
and check this before calling free_netdev().
I checked - no code uses the local->mdev after unregister in this error
path (but even if some did this would be a BUG).
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 4 May 2008 08:34:31 +0000 (01:34 -0700)]
niu: Fix probing regression for maramba on-board chips.
Changeset 7f7c4072ea552f97a0898331322f71986a97299c ("niu: Determine
the # of ports from the card's VPD data") caused maramba on-board
NIU ports to stop probing properly.
The old code had a fallback that would use a num_ports value of
4 if all the probing methods failed, but that was removed.
This restores the fallback of 4 ports, to get things working
again.
Bump driver version and release date.
Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski [Sun, 4 May 2008 03:46:29 +0000 (20:46 -0700)]
sch_htb: remove from event queue in htb_parent_to_leaf()
There is lack of removing a class from the event queue while changing
from parent to leaf which can cause corruption of this rb tree. This
patch fixes a bug introduced by my patch: "sch_htb: turn intermediate
classes into leaves" commit: 160d5e10f87b1dc88fd9b84b31b1718e0fd76398.
Many thanks to Jan 'yanek' Bortl for finding a way to reproduce this
rare bug and narrowing the test case, which made possible proper
diagnosing.
This patch is recommended for all kernels starting from 2.6.20.
Reported-and-tested-by: Jan 'yanek' Bortl <yanek@ya.bofh.cz> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bernard Pidoux [Sat, 3 May 2008 00:03:22 +0000 (17:03 -0700)]
rose: Wrong list_lock argument in rose_node seqops
In rose_node_start() as well as in rose_node_stop() __acquires() and
spin_lock_bh() were wrongly passing rose_neigh_list_lock instead of
rose_node_list_lock arguments.
Signed-off-by: Bernard Pidoux <f6bvp@amsat.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Lezcano [Sat, 3 May 2008 00:00:58 +0000 (17:00 -0700)]
netns: Fix device renaming for sysfs
When a netdev is moved across namespaces with the
'dev_change_net_namespace' function, the 'device_rename' function is
used to fixup kobject and refresh the sysfs tree. The device_rename
function will call kobject_rename and this one will check if there is
an object with the same name and this is the case because we are
renaming the object with the same name.
The use of 'device_rename' seems for me wrong because we usually don't
rename it but just move it across namespaces. As we just want to do a
mini "netdev_[un]register", IMO the functions
'netdev_[un]register_kobject' should be used instead, like an usual
network device [un]registering.
This patch replace device_rename by netdev_unregister_kobject,
followed by netdev_register_kobject.
The netdev_register_kobject will call device_initialize and will raise
a warning indicating the device was already initialized. In order to
fix that, I split the device initialization into a separate function
and use it together with 'netdev_register_kobject' into
register_netdevice. So we can safely call 'netdev_register_kobject' in
'dev_change_net_namespace'.
This fix will allow to properly use the sysfs per namespace which is
coming from -mm tree.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com> Acked-by: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Fri, 2 May 2008 23:57:59 +0000 (16:57 -0700)]
bnx2: Update RV2P firmware for 5709.
The new RV2P firmware fixes 2 issues:
1. The jumbo rx buffer page size is now configurable and set to the
proper PAGE_SIZE. Before, it was assumed to be always 4K.
2. Driver sometimes would crash when receiving jumbo packets mixed
with firmware management packets. This was caused by the old
firmware DMA'ing to the wrong address.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Fri, 2 May 2008 23:57:26 +0000 (16:57 -0700)]
bnx2: Zero out context memory for 5709.
We should zero out the context memory for 5709 before each reset. When
we resume after suspend for example, the memory may not be zero and the
chip may not function correctly.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Fri, 2 May 2008 23:56:44 +0000 (16:56 -0700)]
bnx2: Fix remote PHY initial link state.
On some remote PHY blade systems, the driver receives no initial link
interrupt. As a result, the GMII/MII MAC mode does not get setup properly.
To fix this problem, we add an initial poll of the link state after chip
reset.
With this change, the setting of the initial carrier state in the init
code can be eliminated.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Fri, 2 May 2008 23:56:16 +0000 (16:56 -0700)]
bnx2: Refine remote PHY locking.
bnx2_set_remote_link() should be called under bp->phy_lock to protect
against concurrent polling and interrupt calls. This change is needed
by the next patch which will add one initial poll of the remote PHY
link status.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bridge: forwarding table information for >256 devices
The forwarding table binary interface (my bad choice), only exposes
the port number of the first 8 bits. The bridge code was limited to
256 ports at the time, but now the kernel supports up 1024 ports, so
the upper bits are lost when doing:
brctl showmacs
The fix is to squeeze the extra bits into small hole left in data
structure, to maintain binary compatiablity.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Fri, 2 May 2008 23:49:50 +0000 (16:49 -0700)]
tg3: Update version to 3.92
This patch updates the version number to 3.92.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Fri, 2 May 2008 23:49:29 +0000 (16:49 -0700)]
tg3: Add link state reporting to UMP firmware
All variants of the 5714, 5715, and 5780 offer a feature called the
"Universal Management Port". This feature is implemented in firmware
and is largely transparent to the driver, except...
It turns out that the UMP firmware needs to know the current status
of the link. Because the firmware cannot touch the PHY registers while
the driver is in control of the device, it needs the driver to report
link status changes through an additional handshaking mechanism.
Without this handshake, it has been observed in the field that the UMP
firmware will not operate correctly.
This patch implements the new handshake with the UMP firmware. Since
the handshake uses the same mechanism ASF heartbeats use, code was
added to detect and wait for completion of a pending previous event.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Fri, 2 May 2008 23:48:59 +0000 (16:48 -0700)]
tg3: Fix ethtool loopback test for 5761 BX devices
A CPMU related loopback test bug existed for AX revisions of the 5761.
While that errata has been fixed, the CPMU still slows down the core
clock too far to run the loopback test successfully. This patch
disables the CPMU LINK_SPEED mode just like we do with the AX
revisions of the 5761 and all revisions of the 5784.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Fri, 2 May 2008 23:48:36 +0000 (16:48 -0700)]
tg3: Fix 5761 NVRAM sizes
The 5761 NVRAM sizes assigned to the nvram_size member are half as big
as they should be. This patch corrects the NVRAM sizes and replaces
the hardcoded constants with preprocessor constants for readability.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Fri, 2 May 2008 23:47:53 +0000 (16:47 -0700)]
tg3: Use constant 500KHz MI clock on adapters with a CPMU
The MI clock is not configured correctly on adapters with the CPMU
present. The tg3 driver has code which statically sets the MI clock to
be a fraction of the speed at which the core clock is running.
However, the CPMU can change the adapter's core clock frequency based
on operating conditions. Consequently, the MI will run slow when the
core's clock has been slowed down.
There is a new 500KHz constant frequency clock available on adapters
with a CPMU. This patch removes the static core clock scaling and
configures the MI clock to use this new 500KHz clock instead.
Running the MI clock at slower speeds will not directly result in data
corruption, but it does challenge the PHY read and write routine timeouts.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Machek [Fri, 2 May 2008 23:45:10 +0000 (16:45 -0700)]
hci_usb.h: fix hard-to-trigger race
If someone tries to _urb_unlink while _urb_queue_head is running, he'll see
_urb->queue == NULL and fail to do any locking. Prevent that from happening
by strategically placed barriers.
Signed-off-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Harvey Harrison [Fri, 2 May 2008 23:44:07 +0000 (16:44 -0700)]
dccp: ccid2.c, ccid3.c use clamp(), clamp_t()
Makes the intention of the nested min/max clear.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Travis [Fri, 2 May 2008 23:43:08 +0000 (16:43 -0700)]
net: remove NR_CPUS arrays in net/core/dev.c
Remove the fixed size channels[NR_CPUS] array in net/core/dev.c and
dynamically allocate array based on nr_cpu_ids.
Signed-off-by: Mike Travis <travis@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Harvey Harrison [Fri, 2 May 2008 23:25:46 +0000 (16:25 -0700)]
bluetooth: use get/put_unaligned_* helpers
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6 / log