Pete Zaitcev [Fri, 8 Jun 2007 20:37:49 +0000 (13:37 -0700)]
usb: free DMA mappings if enqueue fails
This patch releases DMA resources if enqueue fails in the HCD.
Linux had this bug ever since we converted from virt_to_bus for 2.4.
It is difficult to hit. A user would need a significant memory pressure
or some other unusual condition.
It was reported to me by IBM. They ran a management application for
RSA II adapters which sent Bulk requests to an Interrupt endpoint.
Submissions got rejected by HCD due to an invalid interval value
and the swiotlb pool became depleted in the matter of hours.
We fixed the invalid interval issue in devio.c separately, but this
seems to be a bug worth fixing as well.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 8 Jun 2007 19:25:02 +0000 (15:25 -0400)]
USB: Handle bogus low-speed Bulk endpoints
A noticeable number of low-speed devices mistakenly include
descriptors for Bulk endpoints, which is forbidden by the USB spec.
In an attempt to make such devices more usable, this patch (as924)
converts the descriptors to Interrupt with an interval of 1 ms.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Benny Halevy [Tue, 15 May 2007 08:15:27 +0000 (11:15 +0300)]
synchronization in usb_serial_put
I think there is a race between usb_serial_put() and
usb_serial_get_by_index() (and get_free_serial()) with regards
to handling the serial port refcount.
usb_serial_get_by_index() gets a reference on the serial port under
table_lock while return_serial releases all the returned ports
from the table under the same lock. However, the table_lock is not
taken around the call to kref_put, theoretically allowing to sneak
in and grab a reference after kref_put has already determined that
the reference count is zero (and before calling destroy_serial)
causing use after free.
According to the USB Specification Revision 2.0 chapter 11.12.5
a hub experiencing an over-current condition must place all
affected ports in the powered-off state. It seems that some root
hubs need port power to be cycled by software in order to get back
to normal functionality after an over-current condition ... like
the EHCI implementation on an MPC8343E.
Signed-off-by: Christian Engelmayer <christian.engelmayer@frequentis.com> Signed-off-by: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Thu, 7 Jun 2007 21:12:25 +0000 (17:12 -0400)]
USB: usb-storage: use kthread_stop() for the control thread
This patch (as923) makes usb-storage's control thread use
kthread_should_stop()/kthread_stop(). The scanning thread can't be
similarly converted until the core kthread implementation allows
threads to call do_exit().
The advantage of this change is that we can now be certain the control
thread has terminated before storage_disconnect() returns. This will
simplify the locking requirements when autosuspend support is added.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Arnaud Patard [Thu, 7 Jun 2007 04:05:49 +0000 (21:05 -0700)]
USB Gadget driver for Samsung s3c2410 ARM SoC
This patch adds the support for the Usb Device Controller on Samsung
S3C24xx SoCs. This driver passes all tests from testusb (including #13)
and has been tested on S3C2410, S3C24212, and S3C2440 SoCs.
Whitespace updates, minor cleanups by David
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Signed-off-by: Ben Dooks <ben-linux@fluff.org> Cc: Herbert Pötzl <herbert@13thfloor.at> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Geoff Levand [Wed, 6 Jun 2007 03:04:35 +0000 (20:04 -0700)]
USB: PS3: USB system-bus rework
USB HCD glue updates to reflect the new PS3 unifed device support.
- Fixed remove() routine.
- Added shutdown() routine.
- Added request_mem_region() call.
- Fixed MODULE_ALIAS().
- Made a proper fix for the hack done to support muti-platform in commit 48fda45120a819ca40cadc50144b55bff1c4c78d.
Alan Stern [Tue, 5 Jun 2007 23:46:26 +0000 (16:46 -0700)]
USB: option: fix usage of urb->status abuse
Might fix bug 8561
On Mon, 4 Jun 2007, Paulo Pereira wrote:
> The patch that you send is not resolving the problem... :(
> I stil have Kernel panic after 45/60 min of work with Ktorrent/Amule...
>
> The Drump is:
>
> Call Trace:
> [<c055fb36>] usb_hcd_submit+0xb1/0x763
> [<f9276488>] ipt_do_table+0x2c7/0x2ef [ip_tables]
> [<f929a6d7>] nf_ct_deliver_cached_events+0x41/0x96 [nf_conntrak]
> [<f9288254>] ipv4_confirm+0x36/0c3b [nf_conntrack_ipv4]
> [<c05ce7c2>] tcp_v4_rcv+0x827/0x899
> [<c05afcc0>] nf_hook_slow+0x4d/0xb5
> [<c042826f>] irq_enter+0x19/0x23
> [<c042826f>] irq_enter+0x19/0x23
> [<c040794c>] do_IRQ+0xbd/0xd1
> [<f90893c9>] option_write+0xa7/0xef [option]
Okay, from this it looks like there's a problem in the option.c serial
driver. Glancing at the code, it's obvious why: The thing totally
abuses the USB API.
Try applying this patch; it should help.
From: Alan Stern <stern@rowland.harvard.edu> Cc: Paulo Pereira <pfmp.404@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Li Yang [Thu, 7 Jun 2007 04:13:44 +0000 (21:13 -0700)]
USB: fsl_usb2_udc: Get max ep number from DCCPARAMS register
Currently the driver is expecting max ep number in platform
data which isn't passing this information. This patch fix
the problem by reading it from DCCPARAMS(Device Controller
Capability Parameters) register. The change also need some
reordering of the probe code.
Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Wed, 30 May 2007 19:39:33 +0000 (15:39 -0400)]
USB: add power/persist device attribute
This patch (as920) adds an extra level of protection to the
USB-Persist facility. Now it will apply by default only to hubs; for
all other devices the user must enable it explicitly by setting the
power/persist device attribute.
The disconnect_all_children() routine in hub.c has been removed and
its code placed inline. This is the way it was originally as part of
hub_pre_reset(); the revised usage in hub_reset_resume() is
sufficiently different that the code can no longer be shared.
Likewise, mark_children_for_reset() is now inline as part of
hub_reset_resume(). The end result looks much cleaner than before.
The sysfs interface is updated to add the new attribute file, and
there are corresponding documentation updates.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Wed, 30 May 2007 19:38:58 +0000 (15:38 -0400)]
USB: unify reset_resume and normal resume
This patch (as919) unifies the code paths used for normal resume and
for reset-resume. Earlier I had failed to note a section in the USB
spec which requires the host to resume a suspended port before
resetting it if the attached device is enabled for remote wakeup.
Since the port has to be resumed anyway, we might as well reuse the
existing code.
The main changes are:
usb_reset_suspended_device() is eliminated.
usb_root_hub_lost_power() is moved down next to the
hub_reset_resume() routine, to which it is logically
related.
finish_port_resume() does a port reset() if the device's
reset_resume flag is set.
usb_port_resume() doesn't check whether the port is initially
enabled if this is a USB-Persist sort of resume.
Code to perform the port reset is added to the resume pathway
for the non-CONFIG_USB_SUSPEND case.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Wed, 30 May 2007 19:38:16 +0000 (15:38 -0400)]
USB: add reset_resume method
This patch (as918) introduces a new USB driver method: reset_resume.
It is called when a device needs to be reset as part of a resume
procedure (whether because of a device quirk or because of the
USB-Persist facility), thereby taking over a role formerly assigned to
the post_reset method. As a consequence, post_reset no longer needs
an argument indicating whether it is being called as part of a
reset-resume. This separation of functions makes the code clearer.
In addition, the pre_reset and post_reset method return types are
changed; they now must return an error code. The return value is
unused at present, but at some later time we may unbind drivers and
re-probe if they encounter an error during reset handling.
The existing pre_reset and post_reset methods in the usbhid,
usb-storage, and hub drivers are updated to match the new
requirements. For usbhid the post_reset routine is also used for
reset_resume (duplicate method pointers); for the other drivers a new
reset_resume routine is added. The change to hub.c looks bigger than
it really is, because mark_children_for_reset_resume() gets moved down
next to the new hub_reset_resume() routine.
A minor change to usb-storage makes the usb_stor_report_bus_reset()
routine acquire the host lock instead of requiring the caller to hold
it already.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Jiri Kosina <jkosina@suse.cz> CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Wed, 30 May 2007 19:35:16 +0000 (15:35 -0400)]
USB: remove excess code from hub.c
This patch (as917) removes a now-unnecessary level of subroutine
nesting from hub.c. Since usb_port_suspend() does nothing but call
hub_port_suspend(), and usb_port_resume() does nothing but call
hub_port_resume(), there's no reason to keep the routines separate.
Also included in the patch are a few cosmetic changes involving
whitespace and use of braces.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Wed, 30 May 2007 19:34:36 +0000 (15:34 -0400)]
USB: separate root and non-root suspend/resume
This patch (as916) completes the separation of code paths for suspend
and resume of root hubs as opposed to non-root devices. Root hubs
will be power-managed through their bus_suspend and bus_resume
methods, whereas normal devices will use usb_port_suspend() and
usb_port_resume().
Changes to the hcd_bus_{suspend,resume} routines mostly represent
motion of code that was already present elsewhere. They include:
Adding debugging log messages,
Setting the device state appropriately, and
Adding a resume recovery time delay.
Changes to the port-suspend and port-resume routines in hub.c include:
Removal of checks for root devices (since they will never
be triggered), and
Removal of checks for NULL or invalid device pointers (these
were left over from earlier kernel versions and aren't needed
at all).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Wed, 30 May 2007 20:51:28 +0000 (16:51 -0400)]
USB: remove __usb_port_suspend
This patch (as915b) combines the public routine usb_port_suspend() and
the private routine __usb_port_suspend() into a single function.
By removing the explicit mention of otg_port in the call to
__usb_port_suspend(), we prevent a possible error in which the system
tries to perform HNP on the wrong port when a non-targeted device is
plugged into a non-OTG port.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a silicon bug in some NEC OHCI chips. The bug appears
at random times and is very, very difficult to reproduce. Without the
following patch, Linux would shut the chip and its associated devices
down. In Apple PowerBooks this leads to an unusable keyboard and mouse
(SSH still working). The idea of restarting the chip is taken from
public Darwin code.
Signed-off-by: Michael Hanselmann <linux-kernel@hansmi.ch> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tony Lindgren [Tue, 29 May 2007 16:57:41 +0000 (09:57 -0700)]
USB: Disable file_storage USB_CONFIG_ATT_WAKEUP
Disable file_storage USB_CONFIG_ATT_WAKEUP as it requires
user interaction during Chapter 9 tests.
Signed-off-by: Tony Lindgren <tony@atomide.com Signed-off-by: Felipe Balbi <felipe.lima@indt.org.br> Acked-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Vladimir Barinov [Wed, 23 May 2007 16:07:48 +0000 (20:07 +0400)]
USB: EHCI: Safe endianness for transfer buffers after reset in case of HUB with TT
This patch fixes the endianness select for transfer buffers in EHCI
controllers that have Transaction Translator built in the hub. Also I
cleaned it up to make rid of magic numbers.
Signed-off-by: Vladimir Barinov <vbarinov@ru.mvista.com> Cc: <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Thu, 24 May 2007 11:52:51 +0000 (13:52 +0200)]
USB: whiteheat driver update
this is an update of the whiteheat driver. It fixes:
- switch from spinlocks to mutexes to prevent sleeping with a spinlock held
- locking to stop races with disconnect
- error handling for commands that time out
Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Mon, 7 May 2007 08:37:08 +0000 (10:37 +0200)]
USB: visor driver adapted to new tty buffering
the new tty buffering code allows usb drivers to stop private buffering.
In fact we must do so to allow flushing to work correctly. This does so
for the visor driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Tue, 15 May 2007 02:36:41 +0000 (19:36 -0700)]
USB: export <linux/usb_gadgetfs> as <linux/usb/gadgetfs.h>
Make sure gadgetfs userspace interface is properly exported:
- Move <linux/usb_gadgetfs.h> to <linux/usb/gadgetfs.h>;
- Export it using Kbuild;
- Add an #include guard;
- Correct some internal documentation;
- Update struct layout so it's the same on 32/64 bit kernels.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Li Yang [Fri, 11 May 2007 09:09:55 +0000 (17:09 +0800)]
USB: ehci_fsl update for MPC831x support
For MPC831x support, change the ehci-fsl driver to preserve
bits set in platform code. Add a common CONFIG_USB_EHCI_FSL
to indicate presence of Freescale EHCI SOC. Add FSL_USB2_DR_OTG
operating mode support, thus both host and device can work for the
mini-ab receptacle. Note: this doesn't enable OTG protocol
support.
Signed-off-by: Li Yang <leoli@freescale.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stefan Roese [Fri, 4 May 2007 18:39:37 +0000 (11:39 -0700)]
USB: Set CONFIG_USB_EHCI_BIG_ENDIAN_MMIO/_DESC in usb/host/Kconfig
Now select the big-endian configuration options
CONFIG_USB_EHCI_BIG_ENDIAN_MMIO and CONFIG_USB_EHCI_BIG_ENDIAN_DESC in
the usb host Kconfig file and not in the platform Kconfig files.
Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: ftdi_sio.c: Allow setting latency timer on FT232RL
The new FT232RL allows setting and getting the value of the latency
timer, like on the FT232BM. However, the driver will not create the
sysfs entries for the RL without this one-line patch.
I have tested it on two systems with successful results.
Alan Stern [Tue, 22 May 2007 15:50:17 +0000 (11:50 -0400)]
USB: rework C++-style comments
This patch (as911) replaces some C++-style commented-out debugging
lines in driver.c with a new "verbose debugging" macro. It makes the
code look cleaner, and it's easier to turn the debugging on or off.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 22 May 2007 15:46:41 +0000 (11:46 -0400)]
USB: prevent char device open/deregister race
This patch (as908) adds central protection in usbcore for the
prototypical race between opening and unregistering a char device.
The spinlock used to protect the minor-numbers array is replaced with
an rwsem, which can remain locked across a call to a driver's open()
method. This guarantees that open() and deregister() will be mutually
exclusive.
The private locks currently used in several individual drivers for
this purpose are no longer necessary, and the patch removes them. The
following USB drivers are affected: usblcd, idmouse, auerswald,
legousbtower, sisusbvga/sisusb, ldusb, adutux, iowarrior, and
usb-skeleton.
As a side effect of this change, usb_deregister_dev() must not be
called while holding a lock that is acquired by open(). Unfortunately
a number of drivers do this, but luckily the solution is simple: call
usb_deregister_dev() before acquiring the lock.
In addition to these changes (and their consequent code
simplifications), the patch fixes a use-after-free bug in adutux and a
race between open() and release() in iowarrior.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mark Lord [Mon, 14 May 2007 23:48:02 +0000 (19:48 -0400)]
USB: hub.c loops forever on resume from ram due to bluetooth
Okay, found it. The root cause here was a missing CONFIG_USB_SUSPEND=y,
which means the hci_usb device never got marked as USB_STATE_SUSPENDED,
which then caused the loop to go on forever.
The system works fine now with CONFIG_USB_SUSPEND=y in the .config.
Here's the patch to prevent future lockups for this or other causes.
I no longer need it, but it does still seem a good idea.
Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Daniel Drake [Wed, 9 May 2007 23:32:24 +0000 (00:32 +0100)]
USB: add USB_DEVICE_AND_INTERFACE_INFO for device matching
Recently, the USB device matching code stopped matching generic interface
matches against devices with vendor-specific device class values.
Some drivers now need to explicitly match USB device ID's (in addition to
generic interface info) to retain the same behaviour as before. This new macro,
suggested by Alan Stern, makes the explicit device/interface matching a little
simpler for those users.
Signed-off-by: Daniel Drake <dsd@gentoo.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 9 May 2007 04:01:30 +0000 (21:01 -0700)]
USB: usb gadget, dead config cleanup
Remove some dead CONFIG_ symbols, and document the status of a few others.
The "gadget_chips.h" references are by and large to drivers which exist
but haven't yet been submitted for merging to the main 2.6 tree.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dave Platt [Tue, 8 May 2007 18:00:12 +0000 (11:00 -0700)]
USB: RTS/CTS handshaking support, DTR fixes for MCT U232 serial adapter
Improvements and fixes to the MCT U232 USB/serial interface driver.
Implement RTS/CTS hardware flow control. Implement HUPCL. Bring
handling of DTR and RTS into conformance with other Linux serial
port drivers - assert both signals when opening device, even if
"crtscts" is not currently selected.
Signed-off-by: Dave Platt <dplatt@radagast.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Arjan van de Ven [Tue, 22 May 2007 19:42:56 +0000 (12:42 -0700)]
USB: Patch to align the various USB timers to fire at the same time
This patch modifies the USB regular 250ms timer to be "perfectly aligned" to
the second and quarters thereof. This change is there to make sure that if
you have multiple USB ports, the timers for all these ports will fire at the
same time rather than all spread out. All spread out wakes the CPU up from
power saving idle a lot more than needed...
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the most recent Digi EdgePort USB serial
devices.
Signed-off-by: Martin K. Petersen <mkp@mkp.net> Signed-off-by: Mike Swift <mikes@digi.com> Signed-off-by: Jeremy McBane <jmcbane@digi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:55:54 +0000 (11:55 -0400)]
USB: Make device reset stop retrying after disconnect
This patch (as898) changes the port reset code in the hub driver. If
a connect change occurs, it is reported the same way as a disconnect
(which of course is what it really is).
It also changes usb_reset_device(), to prevent the routine from futilely
retrying the reset after a disconnect has occurred.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:55:31 +0000 (11:55 -0400)]
USB: EHCI: fix handover for designated full-speed ports
This patch (as895) fixes up a loose end in the port-handover code for
the USB-Persist facility. A special case occurs when a high-speed
device is attached to a port which the user has designated to run at
full-speed only; the port must be disabled before the handover can
take place.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:53:03 +0000 (11:53 -0400)]
USB: add RESET_RESUME device quirk
This patch (as888) adds a new USB device quirk for devices which are
unable to resume correctly. By using the new code added for the
USB-persist facility, it is a simple matter to reset these devices
instead of resuming them. To get things kicked off, a quirk entry is
added for the Philips PSC805.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:52:40 +0000 (11:52 -0400)]
USB: EHCI, OHCI: handover changes
This patch (as887) changes the way ehci-hcd and ohci-hcd handle a loss
of VBUS power during suspend. In order for the USB-persist facility
to work correctly, it is necessary for low- and full-speed devices
attached to a high-speed port to be handed back to the companion
controller during resume processing.
This entails three changes: adding code to ehci-hcd to perform the
handover, removing code from ohci-hcd to turn off ports during
root-hub reinit, and adding code to ohci-hcd to turn on ports during
PCI controller resume. (Other bus glue resume methods for platforms
supporting high-speed controllers would need a similar change, if any
existed.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:52:20 +0000 (11:52 -0400)]
USB: add USB-Persist facility
This patch (as886) adds the controversial USB-persist facility,
allowing USB devices to persist across a power loss during system
suspend.
The facility is controlled by a new Kconfig option (with appropriate
warnings about the potential dangers); when the option is off the
behavior will remain the same as it is now. But when the option is
on, people will be able to use suspend-to-disk and keep their USB
filesystems intact -- something particularly valuable for small
machines where the root filesystem is on a USB device!
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pete Zaitcev [Thu, 3 May 2007 23:51:16 +0000 (16:51 -0700)]
usbmon: Add class for binary interface
Add a class which allows for an easier integration with udev.
This code was originally written by Paolo Abeni, and arrived to my tree
as a part of big patch to add binary API on December 18. As I understand,
Paolo always meant the class to be a part of the whole thing. This is his
udev rule to go along with the patch:
Kees Lemmens [Tue, 27 Mar 2007 10:34:30 +0000 (12:34 +0200)]
USB: oti6858 usb-serial driver (in Nokia CA-42 cable)
Last week I've been searching for a driver for the CA-42 cable (see usb
below) that fitted my kernel 2.6.20. I only found an abandoned version for a
driver on your website that indeed worked on 2.6.18 but wouldn't even
compile with a more recent 2.6.20 kernel.
I fiddled 2 evenings with the kernel code and have patched it up now to work
with the modifications in the 2.6.20 kernel. The patch is attached hereafter
and it works fine (at least for me :-) ).
Bus 2 Device 13: ID 0ea0:6858 Ours Technology, Inc.
I had to fiddle a little with the settings in .gnokiirc but that also
occurred with the older 2.6.18 kernel. Nevertheless, on one system with this
cable and my Nokia 6070 I had best results with :
model = 6510
connection = dku5
while on an other system with the same kernel, cable and phone it only worked
with :
model = AT
connection = serial
serial_write_usleep = 1
David Brownell [Thu, 17 May 2007 19:21:19 +0000 (12:21 -0700)]
USB: ehci refcounts work on ppc7448
Remove atomic operations on the reference counter for EHCI queue heads.
On various platforms (including ppc7448), atomic operations are unusable
with dma-coherent memory.
Signed-off-by: Steven J. Hill <sjhill1@rockwellcollins.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jan Engelhardt [Fri, 11 May 2007 06:04:13 +0000 (23:04 -0700)]
USB: Use menuconfig objects
Make a "menuconfig" out of the Kconfig objects "menu, ..., endmenu", so that
the user can disable all the options in that menu at once instead of having to
disable each option separately.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:55:11 +0000 (11:55 -0400)]
USB: make hub driver's release more robust
This revised patch (as893c) improves the method used by the hub driver
to release its private data structure. The current code is non-robust,
relying on a memory region not getting reused by another driver after
it has been freed. The patch adds a reference count to the structure,
resolving the question of when to release it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:54:50 +0000 (11:54 -0400)]
USB: remove "locktree" routine from the hub driver
This patch (as892) removes the "locktree" routine from the hub driver.
It currently is used in only one place, by a single kernel thread;
hence it isn't doing any good.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:54:28 +0000 (11:54 -0400)]
USB: remove references to dev.power.power_state
This revised patch (as891b) removes two unnecessary references to
intf->dev.power.power_state from usb-storage, and replaces a reference
to root_hub->dev.power.power_state with a check of hcd->state. This
is in preparation for the removal of dev.power.power_state, which is
already deprecated.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:53:30 +0000 (11:53 -0400)]
USB: don't unsuspend for a new connection
This patch (as889) prevents the hub driver from trying to resume a
port when there is a new connection. For one thing, the resume is not
needed -- the upcoming port reset will clear the suspend feature
automatically. For another, on some systems the resume fails and
causes problems.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:51:54 +0000 (11:51 -0400)]
USB: move bus_suspend and bus_resume method calls
This patch (as885) moves the root-hub bus_suspend() and bus_resume()
method calls from the hub driver's suspend and resume methods into the
usb_generic driver methods, where they make just as much sense.
Their old locations were not fully correct. For example, in a kernel
compiled without CONFIG_USB_SUSPEND, if one were to do:
echo -n 1-0:1.0 >/sys/bus/usb/drivers/hub/unbind
to unbind the hub driver from a root hub, there would then be no way
to suspend that root hub. Attempts to put the system to sleep would
fail; the USB controller driver would refuse to suspend because the
root hub was still active.
The patch also makes a very slight change in the way devices with no
driver are handled during suspend. Rather than doing a standard USB
port-suspend directly, now the suspend routine in usb_generic is
called. In practice this should never affect anyone.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:51:25 +0000 (11:51 -0400)]
USB: Implement PM FREEZE and PRETHAW
This patch (as884) finally implements the time-saving semantics
possible with the Power Management FREEZE and PRETHAW events. Their
proper handling requires only that devices be quiesced, with
interrupts and DMA turned off; non-root USB devices don't actually
need to be put in a suspended state. The patch checks and avoids
doing the suspend call when possible.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:49:57 +0000 (11:49 -0400)]
USB: interface PM state
This patch (as880) strives to keep the PM core's idea of a USB
interface's power state in synch with usbcore's own idea. In the end
this doesn't really matter, but it's better to be consistent.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: r8a66597-hcd: host controller driver for R8A66597
I would like to submit Renesas R8A66597 USB HCD driver.
R8A66597 is Renesas USB 2.0 host and peripheral combined
controller device originally designed for embedded products.
As a limitation of this device, it does not support externel
hub more than 2 tier, and cannot communicate with a USB
device more than 10. Then this device is not compatible with
EHCI and/or OHCI, I wrote driver support patch based on
sl811 code.
This driver has the following unique specifications:
- Implement transfer timeout to share one pipe with plural endpoint.
- Detach detection of a USB device connected to externel hub.
The driver has been tested external hub, usb-hdd, usb-cdrom,
usb-speaker, mice, keyboard, and usbtest driver.
Simon Arlott [Fri, 11 May 2007 06:04:11 +0000 (23:04 -0700)]
USB: cxacru: Cleanup sysfs attribute code
This changes the format of unknown status values to be less verbose and
uses an array instead of several different snprintf calls. Since only
enum values are assigned to it, poll_state is changed from int to enum.
Use abs() for dB values instead of two almost identical return lines.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Acked-by: Duncan Sands <duncan.sands@math.u-psud.fr> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stefan Roese [Tue, 1 May 2007 16:29:37 +0000 (09:29 -0700)]
USB: EHCI support for big-endian descriptors
This patch implements supports for EHCI controllers whose in-memory
data structures are represented in big-endian format. This is needed
(unfortunately) for the AMCC PPC440EPx SoC EHCI controller; the EHCI
spec doesn't specify little-endian format, although that's what most
other implementations use.
The guts of the patch are to introduce the hc32 type and change all
references from le32 to hc32. All access routines are converted from
cpu_to_le32(...) to cpu_to_hc32(ehci, ...) and similar for the other
"direction". (This is the same approach used with OHCI.)
David fixed:
Whitespace fixes; refresh against ehci cpufreq patch; move glue
for that PPC driver to the patch adding it; fix free symbol
capture bugs in modified "constant" macros; and make "hc32" etc
be "le32" unless we really need the BE options, so "sparse" can
do some real good.
Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
EHCI controllers that don't cache enough microframes can get MMF errors
when CPU frequency changes occur between the start and completion of
split interrupt transactions, due to delays in reading main memory
(caused by CPU cache snoop delays).
This patch adds a cpufreq notifier to the EHCI driver that will
inactivate split interrupt transactions during frequency transitions.
It was tested on Intel ICH7 and Serverworks/Broadcom HT1000 EHCI
controllers.
Signed-off-by: Stuart Hayes <stuart_hayes@dell.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jonathan Brassow [Thu, 12 Jul 2007 16:29:15 +0000 (17:29 +0100)]
dm raid1: handle log failure
When writing to a mirror, the log must be updated first. Failure
to update the log could result in the log not properly reflecting
the state of the mirror if the machine should crash.
We change the return type of the rh_flush function to give us
the ability to check if a log write was successful. If the
log write was unsuccessful, we fail the writes to avoid the
case where the log does not properly reflect the state of the
mirror.
A follow-up patch - which is dependent on the ability to
requeue I/O's to core device-mapper - will requeue the I/O's
for retry (allowing the mirror to be reconfigured.)
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jonathan Brassow [Thu, 12 Jul 2007 16:29:04 +0000 (17:29 +0100)]
dm raid1: handle resync failures
Device-mapper mirroring currently takes a best effort approach to
recovery - failures during mirror synchronization are completely ignored.
This means that regions are marked 'in-sync' and 'clean' and removed
from the hash list. Future reads and writes that query the region
will incorrectly interpret the region as in-sync.
This patch handles failures during the recovery process. If a failure
occurs, the region is marked as 'not-in-sync' (aka RH_NOSYNC) and added
to a new list 'failed_recovered_regions'.
Regions on the 'failed_recovered_regions' list are not marked as 'clean'
upon removal from the list. Furthermore, if the DM_RAID1_HANDLE_ERRORS
flag is set, the region is marked as 'not-in-sync'. This action prevents
any future read-balancing from choosing an invalid device because of the
'not-in-sync' status.
If "handle_errors" is not specified when creating a mirror (leaving the
DM_RAID1_HANDLE_ERRORS flag unset), failures will be ignored exactly as they
would be without this patch. This is to preserve backwards compatibility with
user-space tools, such as 'pvmove'. However, since future read-balancing
policies will rely on the correct sync status of a region, a user must choose
"handle_errors" when using read-balancing.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stefan Bader [Thu, 12 Jul 2007 16:28:33 +0000 (17:28 +0100)]
dm: disable barriers
This patch causes device-mapper to reject any barrier requests. This is done
since most of the targets won't handle this correctly anyway. So until the
situation improves it is better to reject these requests at the first place.
Since barrier requests won't get to the targets, the checks there can be
removed.
Cc: stable@kernel.org Signed-off-by: Stefan Bader <shbader@de.ibm.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jonathan Brassow [Thu, 12 Jul 2007 16:28:25 +0000 (17:28 +0100)]
dm raid1: clear region outside spinlock
A clear_region function is permitted to block (in practice, rare) but gets
called in rh_update_states() with a spinlock held.
The bits being marked and cleared by the above functions are used
to update the on-disk log, but are never read directly. We can
perform these operations outside the spinlock since the
bits are only changed within one thread viz.
- mark_region in rh_inc()
- clear_region in rh_update_states().
So, we grab the clean_regions list items via list_splice() within the
spinlock and defer clear_region() until we iterate over the list for
deletion - similar to how the recovered_regions list is already handled.
We then move the flush() call down to ensure it encapsulates the changes
which are done by the later calls to clear_region().
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Milan Broz [Thu, 12 Jul 2007 16:28:13 +0000 (17:28 +0100)]
dm snapshot: permit invalid activation
Allow invalid snapshots to be activated instead of failing.
This allows userspace to reinstate any given snapshot state - for
example after an unscheduled reboot - and clean up the invalid snapshot
at its leisure.
Cc: stable@kernel.org Signed-off-by: Milan Broz <mbroz@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Milan Broz [Thu, 12 Jul 2007 16:28:00 +0000 (17:28 +0100)]
dm snapshot: fix invalidation deadlock
Process persistent exception store metadata IOs in a separate thread.
A snapshot may become invalid while inside generic_make_request().
A synchronous write is then needed to update the metadata while still
inside that function. Since the introduction of
md-dm-reduce-stack-usage-with-stacked-block-devices.patch this has to
be performed by a separate thread to avoid deadlock.
Signed-off-by: Milan Broz <mbroz@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Milan Broz [Thu, 12 Jul 2007 16:27:24 +0000 (17:27 +0100)]
dm raid1: fix status
Fix mirror status line broken in dm-log-report-fault-status.patch:
- space missing between two words
- placeholder ("0") required for compatibility with a subsequent patch
- incorrect offset parameter
Cc: stable@kernel.org Signed-off-by: Milan Broz <mbroz@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use new KMEM_CACHE() macro and make the newly-exposed structure names more
meaningful. Also remove some superfluous casts and inlines (let a modern
compiler be the judge).
Acked-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (50 commits)
[ARM] sa1100: remove boot time RTC initialisation
[ARM] sa1100: stop doing our own rtc management over suspend
[ARM] 4474/1: Do not check the PSR_F_BIT in valid_user_regs
[ARM] 4473/2: Take the HWCAP definitions out of the elf.h file
[ARM] pxa: move platform devices to separate header file
[ARM] pxa: move device registration into CPU-specific file
[ARM] pxa: remove boot time RTC initialisation
[ARM] pxa: stop doing our own rtc management over suspend
[ARM] 4451/1: pxa: make dma.c generic and remove cpu specific dma code
[ARM] 4450/1: pxa: add pxa25x_init_irq() and pxa27x_init_irq()
[ARM] 4440/1: PXA: enable the checking of ICIP2 for IRQs
[ARM] 4438/1: PXA: remove #ifdef .. #endif from pxa_gpio_demux_handler()
[ARM] 4437/1: PXA: move the GPIO IRQ initialization code to pxa_init_irq_gpio()
[ARM] 4436/1: PXA: move low IRQ initialization code to pxa_init_irq_low()
[ARM] 4435/1: PXA: remove PXA_INTERNAL_IRQS
[ARM] 4434/1: PXA: remove PXA_IRQ_SKIP
[ARM] pxa: Fix PXA27x suspend type validation, remove pxa_pm_prepare()
[ARM] pxa: move pm_ops structure into CPU specific files
[ARM] pxa: introduce cpu_is_pxaXXX macros
[ARM] pxa: remove MMC register defines from pxa-regs.h
...
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
security: unexport mmap_min_addr
SELinux: use SECINITSID_NETMSG instead of SECINITSID_UNLABELED for NetLabel
security: Protection for exploiting null dereference using mmap
SELinux: Use %lu for inode->i_no when printing avc
SELinux: allow preemption between transition permission checks
selinux: introduce schedule points in policydb_destroy()
selinux: add selinuxfs structure for object class discovery
selinux: change sel_make_dir() to specify inode counter.
selinux: rename sel_remove_bools() for more general usage.
selinux: add support for querying object classes and permissions from the running policy
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Fix sysfs_create_file return value handling
[CPUFREQ] ondemand: fix tickless accounting and software coordination bug
[CPUFREQ] ondemand: add a check to avoid negative load calculation
[CPUFREQ] Keep userspace governor quiet when it is not being used
[CPUFREQ] Longhaul - Proper register access
[CPUFREQ] Kconfig powernow-k8 driver should depend on ACPI P-States driver
[CPUFREQ] Longhaul - Replace ACPI functions with direct I/O
[CPUFREQ] Longhaul - Remove duplicate multipliers
[CPUFREQ] Longhaul - Embedded "conservative"
[CPUFREQ] acpi-cpufreq: Proper ReadModifyWrite of PERF_CTL MSR
[CPUFREQ] check return value of sysfs_create_file
[CPUFREQ] Longhaul - Check ACPI "BM DMA in progress" bit
[CPUFREQ] Longhaul - Move old_ratio to correct place
[CPUFREQ] Longhaul - VT8237 support
[CPUFREQ] Longhaul - Use all kinds of support
[CPUFREQ] powernow-k8: clarify number of cores.
projects / linux-2.6 / log