Zachary Amsden [Mon, 5 Mar 2007 08:30:38 +0000 (00:30 -0800)]
[PATCH] vmi: paravirt drop udelay op
Not respecting udelay causes problems with any virtual hardware that is passed
through to real hardware. This can be noticed by any device that interacts
with the real world in real time - like AP startup, which takes real time. Or
keyboard LEDs, which should blink in real-time. Or floppy drives, but only
when passed through to a real floppy controller on OSes which can't
sufficiently buffer the floppy commands to emulate a zero latency floppy. Or
IDE drives, when connecting to a physical CDROM.
This was mostly a hack to get the kernel to boot faster, but it introduced a
number of misvirtualization bugs, and Alan and Pavel argued pretty strongly
against it. We were the only client, and now want to clean up this cruft.
Zachary Amsden [Mon, 5 Mar 2007 08:30:37 +0000 (00:30 -0800)]
[PATCH] vmi: fix highpte
Provide a PT map hook for HIGHPTE kernels to designate where they are mapping
page tables. This information is required so the physical address of PTE
updates can be determined; otherwise, the mm layer would have to carry the
physical address all the way to each PTE modification callsite, which is even
more hideous that the macros required to provide the proper hooks.
So lets not mess up arch neutral code to achieve this, but keep the horror in
an #ifdef HIGHPTE in include/asm-i386/pgtable.h. I had to use macros here
because some types are not yet defined in all the include paths for this
header.
This patch is absolutely required for HIGHPTE kernels to operate properly with
VMI.
Zachary Amsden [Mon, 5 Mar 2007 08:30:36 +0000 (00:30 -0800)]
[PATCH] vmi: cpu cycles fix
In order to share the common code in tsc.c which does CPU Khz calibration, we
need to make an accurate value of CPU speed available to the tsc.c code. This
value loses a lot of precision in a VM because of the timing differences with
real hardware, but we need it to be as precise as possible so the guest can
make accurate time calculations with the cycle counters.
Zachary Amsden [Mon, 5 Mar 2007 08:30:35 +0000 (00:30 -0800)]
[PATCH] vmi: sched clock paravirt op fix
The custom_sched_clock hook is broken. The result from sched_clock needs to
be in nanoseconds, not in CPU cycles. The TSC is insufficient for this
purpose, because TSC is poorly defined in a virtual environment, and mostly
represents real world time instead of scheduled process time (which can be
interrupted without notice when a virtual machine is descheduled).
To make the scheduler consistent, we must expose a different nature of time,
that is scheduled time. So deprecate this custom_sched_clock hack and turn it
into a paravirt-op, as it should have been all along. This allows the tsc.c
code which converts cycles to nanoseconds to be shared by all paravirt-ops
backends.
It is unfortunate to add a new paravirt-op, but this is a very distinct
abstraction which is clearly different for all virtual machine
implementations, and it gets rid of an ugly indirect function which I
ashamedly admit I hacked in to try to get this to work earlier, and then even
got in the wrong units.
Zachary Amsden [Mon, 5 Mar 2007 08:30:34 +0000 (00:30 -0800)]
[PATCH] vmi: timer fixes round two
Critical bugfixes for the VMI-Timer code.
1) Do not setup a one shot alarm if we are keeping the periodic alarm
armed. Additionally, since the periodic alarm can be run at a lower rate
than HZ, let's fixup the guard to the no-idle-hz mode appropriately. This
fixes the bug where the no-idle-hz mode might have a higher interrupt rate
than the non-idle case.
2) The interrupt handler can no longer adjust xtime due to nested lock
acquisition. Drop this. We don't need to check for wallclock time at
every tick, it can be done in userspace instead.
3) Add a bypass to disable noidle operation. This is useful as a last
minute workaround, or testing measure.
4) The code to skip the IO_APIC timer testing (no_timer_check) should be
conditional on IO_APIC, not SMP, since UP kernels can have this configured
in as well.
Signed-off-by: Dan Hecht <dhecht@vmware.com> Signed-off-by: Zachary Amsden <zach@vmware.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently we do not check for vma flags if sys_move_pages is called to move
individual pages. If sys_migrate_pages is called to move pages then we
check for vm_flags that indicate a non migratable vma but that still
includes VM_LOCKED and we can migrate mlocked pages.
Extract the vma_migratable check from mm/mempolicy.c, fix it and put it
into migrate.h so that is can be used from both locations.
Problem was spotted by Lee Schermerhorn
Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Mundt [Mon, 5 Mar 2007 08:30:31 +0000 (00:30 -0800)]
[PATCH] fb: sm501fb off-by-1 sysfs store
Currently sm501fb_crtsrc_store() won't allow the routing to be changed via
echos from userspace in to the sysfs file. The reason for this is that the
strnicmp() for both heads uses a sizeof() for the string length, which ends
up being strlen() + 1 (\0 in the normal case, but the echo gives a newline,
which is where the issue occurs), this then causes a mismatch and
subsequently bails with the -EINVAL.
In addition to this, the hardcoded lengths were then used for the store
length that was returned, which ended up being erroneous and resulting in a
write error. There's also no point in returning anything but the full
length since it will -EINVAL out on a mismatch well before then anyways.
sizeof("string") is great for making sure you have space in your buffer,
but rather less so for string comparisons :-)
Signed-off-by: Paul Mundt <lethal@linux-sh.org> Acked-by: Ben Dooks <ben-linux@fluff.org> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Con Kolivas [Mon, 5 Mar 2007 08:30:29 +0000 (00:30 -0800)]
[PATCH] sched: remove SMT nice
Remove the SMT-nice feature which idles sibling cpus on SMT cpus to
facilitiate nice working properly where cpu power is shared. The idling of
cpus in the presence of runnable tasks is considered too fragile, easy to
break with outside code, and the complexity of managing this system if an
architecture comes along with many logical cores sharing cpu power will be
unworkable.
Remove the associated per_cpu_gain variable in sched_domains used only by
this code.
Also:
The reason is that with dynticks enabled, this code breaks without yet
further tweaks so dynticks brought on the rapid demise of this code. So
either we tweak this code or kill it off entirely. It was Ingo's preference
to kill it off. Either way this needs to happen for 2.6.21 since dynticks
has gone in.
Signed-off-by: Con Kolivas <kernel@kolivas.org> Acked-by: Ingo Molnar <mingo@elte.hu> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Berg [Mon, 5 Mar 2007 08:30:27 +0000 (00:30 -0800)]
[PATCH] schedule wext/rtnl for removal
Since wext is being replaced as fast as we can (it'll probably stick around
for legacy drivers though) and the wext/netlink stuff was never really
used, this schedules it for removal.
The removal schedule is tight but there are no users of the code, the main
user of the wext user interface are the wireless-tools, they only have an
alpha version using the netlink interface and even that is incomplete.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove remaining references to saved registers now that
uart_handle_sysrq_char() does not want them.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Brownell [Mon, 5 Mar 2007 08:30:18 +0000 (00:30 -0800)]
[PATCH] add CONFIG_GENERIC_GPIO
Most drivers using GPIOs already know they are running on a system that
supports the generic GPIO calls, because of other platform dependencies.
But the generic GPIO-based LED and input button drivers can't know that.
So this patch adds a Kconfig hook, GENERIC_GPIO, to mark the platforms
where <asm/gpio.h> will do the right thing. Currently that's a bunch of
ARMs, and AVR32; more are on the way.
It also fixes a dependency bug for the gpio button input driver; it was
wrong to start with, now it covers all platforms with GENERIC_GPIO.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Richard Purdie <rpurdie@rpsys.net> Cc: Arnaud Patard <arnaud.patard@rtp-net.org> Cc: <raph@8d.com> Cc: <msvoboda@ra.rockwell.com> Cc: pHilipp Zabel <philipp.zabel@gmail.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Dmitry Torokhov <dtor@mail.ru> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tony Breeds [Mon, 5 Mar 2007 08:30:14 +0000 (00:30 -0800)]
[PATCH] Fix soft lockup with iSeries viocd driver
Fix soft lockup with iSeries viocd driver, caused by eventually calling
end_that_request_first() with nr_bytes 0.
Some versions of hald do an SG_IO ioctl on the viocd device which becomes a
request with hard_nr_sectors and hard_cur_sectors set to zero. Passing zero
as the number of sectors to end_request() (which calls
end_that_request_first()) causes an infinite loop when the bio is being freed.
This patch makes sure that the zero is never passed. It only requires some
number larger the the request size the terminate the loop.
The lockup is triggered by hald, interrogating the device.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Brownell [Mon, 5 Mar 2007 08:30:13 +0000 (00:30 -0800)]
[PATCH] parport is an orphan
The writing on the wall seem to be that the parport stack is orphaned,
rather than maintained by four folk ... and having a webpage that says the
latest patches are based on a 2.5 kernel.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[PATCH] msi: support masking msi irqs without a mask bit
For devices that do not support msi-x we only support 1 interrupt. Therefore
we can disable that one interrupt by disabling the msi capability itself. If
we leave the intx interrupts disabled while we have the msi capability
disabled no interrupts should be delivered from that device.
Devices with just the minimal msi support (and thus hitting this code path)
include things like the intel e1000 nic, so it looks like is going to be a
fairly common case and thus important to get right.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Michael Ellerman <michael@ellerman.id.au> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
enable/disable_msi_mode have several side effects which keeps them from being
generally useful. So this patch replaces them with with two much more
targeted functions: msi_set_enable and msix_set_enable.
This patch makes pci_dev->msi_enabled and pci_dev->msix_enabled the definitive
way to test if linux has enabled the msi capability, and has the appropriate
msi data structures set up.
This patch ensures that while writing the msi messages in save/restore and
during device initialization we have the msi capability disabled so we don't
get into races. The pci spec requires that we do not have the msi capability
enabled and the msi messages unmasked while we write the messages. Completely
disabling the capability is overkill but it is easy :)
Care has been taken so we never have both a msi capability and intx enabled
simultaneously. We haven't run into a problem yet but better safe then sorry.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Michael Ellerman <michael@ellerman.id.au> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[PATCH] msi: sanely support hardware level msi disabling
In some cases when we are not using msi we need a way to ensure that the
hardware does not have an msi capability enabled. Currently the code has been
calling disable_msi_mode to try and achieve that. However disable_msi_mode
has several other side effects and is only available when msi support is
compiled in so it isn't really appropriate.
Instead this patch implements pci_msi_off which disables all msi and msix
capabilities unconditionally with no additional side effects.
pci_disable_device was redundantly clearing the bus master enable flag and
clearing the msi enable bit. A device that is not allowed to perform bus
mastering operations cannot generate intx or msi interrupt messages as those
are essentially a special case of dma, and require bus mastering. So the call
in pci_disable_device to disable msi capabilities was redundant.
quirk_pcie_pxh also called disable_msi_mode and is updated to use pci_msi_off.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Michael Ellerman <michael@ellerman.id.au> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Mon, 5 Mar 2007 08:30:04 +0000 (00:30 -0800)]
[PATCH] cyclades: return closing_wait
In http://bugzilla.kernel.org/show_bug.cgi?id=8065, Shen points out that the
cyclades driver forget to return closing_wait to userspace.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Shen <shanlu@cs.uiuc.edu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[VLAN]: Avoid a 4-order allocation.
[HDLC] Fix dev->header_cache_update having a random value.
[NetLabel]: Verify sensitivity level has a valid CIPSO mapping
[PPPOE]: Key connections properly on local device.
[AF_UNIX]: Test against sk_max_ack_backlog properly.
[NET]: Fix bugs in "Whether sock accept queue is full" checking
Linus Torvalds [Sun, 4 Mar 2007 21:15:48 +0000 (13:15 -0800)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm: (30 commits)
[ARM] Acorn: move the i2c bus driver into drivers/i2c
[ARM] ARM SCSI: Don't try to dma_map_sg too many scatterlist entries
[ARM] ARM FAS216: don't modify scsi_cmnd request_bufflen
[ARM] rtc-pcf8583: Final fixes for this RTC on RiscPC
[ARM] rtc-pcf8583: correct month and year offsets
[ARM] rtc-pcf8583: don't use BCD_TO_BIN/BIN_TO_BCD
[ARM] EBSA110: Work around build errors
[ARM] 4241/1: Define mb() as compiler barrier on a uniprocessor system
[ARM] 4239/1: S3C24XX: Update kconfig entries for PM
[ARM] 4238/1: S3C24XX: docs: update suspend and resume
[ARM] 4237/2: oprofile: Always allow backtraces on ARM
[ARM] Yet more asm/apm-emulation.h stuff
ARM: OMAP: Add missing get_irqnr_preamble and arch_ret_to_user for omap2
ARM: OMAP: Use linux/delay.h not asm/delay.h
ARM: OMAP: Remove obsolete alsa typedefs
ARM: OMAP: omap1510->15xx conversions needed for sx1
ARM: OMAP: Add missing includes to board-nokia770
ARM: OMAP: Workqueue changes for board-h4.c
ARM: OMAP: dmtimer.c omap1 register fix
ARM: OMAP: board-nokia770: correct lcd name
...
Linus Torvalds [Sun, 4 Mar 2007 21:15:00 +0000 (13:15 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] MTX1: clear PCI errors
[MIPS] MTX1: add idsel cardbus ressources
[MIPS] MTX1: remove unneeded settings
[MIPS] dma_sync_sg_for_cpu is a no-op except for non-coherent R10000s.
[MIPS] Cobalt: update reserved resources
[MIPS] SN: PCI fixup needs to include <irq.h>.
[MIPS] DMA: Fix a bunch of warnings due to missing inline keywords.
[MIPS] RM: It should be #ifdef CONFIG_FOO not #if CONFIG_FOO ...
[MIPS] Fix and cleanup the mess that a dozen prom_printf variants are.
[MIPS] DEC: Remove redeclarations of mips_machgroup and mips_machtype.
[MIPS] No need to write c0_compare in plat_timer_setup
[MIPS] Convert to RTC-class ds1742 driver
[MIPS] Oprofile: Add missing break statements.
[MIPS] jmr3927: build fix
[MIPS] SNI: Fix mc146818_decode_year
[MIPS] Replace sys32_timer_create with the generic compat_sys_timer_create.
[MIPS] Replace sys32_socketcall with the generic compat_sys_socketcall.
[MIPS] N32 waitid is the same as o32.
Russell King [Sun, 4 Mar 2007 20:40:50 +0000 (20:40 +0000)]
[ARM] Acorn: move the i2c bus driver into drivers/i2c
Move the Acorn IOC/IOMD I2C bus driver from drivers/i2c, strip
out the reminants of the platform specific parts of the old
PCF8583 RTC code, and remove the old obsolete PCF8583 driver.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 4 Mar 2007 20:21:38 +0000 (20:21 +0000)]
[ARM] ARM SCSI: Don't try to dma_map_sg too many scatterlist entries
An off-by-one bug meant we were always trying to map one too many
scatterlist entries. This was mostly harmless prior to the checks
going in to consistent_sync(), but now causes the kernel to BUG.
Also, powertec.c was missing an assignment to info->ec.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 4 Mar 2007 20:33:07 +0000 (20:33 +0000)]
[ARM] rtc-pcf8583: Final fixes for this RTC on RiscPC
Replace the I2C bus address, as per drivers/acorn/char/pcf8583.c.
Also, since this driver also contains Acorn RiscPC specific code
for obtaining the current year from the SRAM (and updating the
platform specific checksum when writing new data back) this is
NOT a platform independent driver.
Document it as such, and update the dependencies to reflect this
fact.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 4 Mar 2007 20:12:07 +0000 (20:12 +0000)]
[ARM] rtc-pcf8583: don't use BCD_TO_BIN/BIN_TO_BCD
Both BCD_TO_BIN(x) and BIN_TO_BCD(x) have an unexpected side-effect -
not only do they return the value as expected, they _modify_ their
argument in the process.
Let's play it safe and avoid these macros.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Avi Kivity [Mon, 26 Feb 2007 14:29:43 +0000 (16:29 +0200)]
KVM: Fix bogus failure in kvm.ko module initialization
A bogus 'return r' can cause an otherwise successful module load to fail.
This both denies users the use of kvm, and it also denies them the use of
their machine, as it leaves a filesystem registered with its callbacks
pointing into now-freed module memory.
Fix by returning a zero like a good module.
Thanks to Richard Lucassen <mailinglists@lucassen.org> (?) for reporting
the problem and for providing access to a machine which exhibited it.
Uri Lublin [Thu, 22 Feb 2007 15:37:32 +0000 (17:37 +0200)]
KVM: Remove write access permissions when dirty-page-logging is enabled
Enabling dirty page logging is done using KVM_SET_MEMORY_REGION ioctl.
If the memory region already exists, we need to remove write accesses,
so writes will be caught, and dirty pages will be logged.
Signed-off-by: Uri Lublin <uril@qumranet.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
Avi Kivity [Wed, 21 Feb 2007 16:04:26 +0000 (18:04 +0200)]
KVM: Per-vcpu inodes
Allocate a distinct inode for every vcpu in a VM. This has the following
benefits:
- the filp cachelines are no longer bounced when f_count is incremented on
every ioctl()
- the API and internal code are distinctly clearer; for example, on the
KVM_GET_REGS ioctl, there is no need to copy the vcpu number from
userspace and then copy the registers back; the vcpu identity is derived
from the fd used to make the call
Right now the performance benefits are completely theoretical since (a) we
don't support more than one vcpu per VM and (b) virtualization hardware
inefficiencies completely everwhelm any cacheline bouncing effects. But
both of these will change, and we need to prepare the API today.
ide: make legacy IDE VLB modules check for the "probe" kernel params (v2)
Legacy IDE VLB host drivers didn't check for "probe" options when compiled
as modules, which was obviously wrong as we don't want module to poke at
random I/O ports by simply loading it. Fix it by adding "probe" module param
to legacy IDE VLB host drivers.
v2:
* don't obsolete old "ide0=dtc2278/ht6560b/qd65xx/ali14xx/umc8672"
IDE driver options yet (per Alan Cox's request) and enhance documentation
Akira Iguchi [Sat, 3 Mar 2007 16:48:55 +0000 (17:48 +0100)]
scc_pata: bugfix for checking DMA IRQ status
On Tuesday 27 February 2007, Akira Iguchi wrote:
>
> But since I sent the first patch, I found a bug for checking DMA IRQ status.
> (http://www.spinics.net/lists/linux-ide/msg06903.html)
> Then I sent the fixed patch for libata only. So my drivers/ide patch
> still has same bug and I want to fix it, too.
>
> The following patch fixes this bug. Please apply this patch.
Jan Beulich [Sat, 3 Mar 2007 16:48:54 +0000 (17:48 +0100)]
adjust legacy IDE resource setting (v2)
The change to force legacy mode IDE channels' resources to fixed non-zero
values confuses (at least some versions of) X, because the values reported
by the kernel and those readable from PCI config space aren't consistent
anymore. Therefore, this patch arranges for the respective BARs to also
get updated if possible.
Signed-off-by: Jan Beulich <jbeulich@novell.com> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Andrew Morton [Sat, 3 Mar 2007 16:48:54 +0000 (17:48 +0100)]
ide: fix pmac breakage
Fix breakage added in the IDE devel tree.
Add header, then fix
drivers/ide/ppc/pmac.c: In function `pmac_ide_setup_dma':
drivers/ide/ppc/pmac.c:2044: warning: assignment from incompatible pointer type
drivers/ide/ppc/pmac.c: In function `pmac_ide_dma_host_on':
drivers/ide/ppc/pmac.c:1989: warning: control reaches end of non-void function
include/linux/pci.h: In function `pmac_ide_init':
drivers/ide/ppc/pmac.c:1563: warning: ignoring return value of `pci_register_driver', declared with attribute warn_unused_result
Then add some apparently-long-missing error handling.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The function ide_get_best_pio_mode() fails to return the correct IORDY setting
for the explicitly specified modes -- fix this along with the heading comment,
and also remove the long commented out code.
Also, while at it, correct the misliading comment about the PIO cycle time in
<linux/ide.h> -- it actually consists of only the active and recovery periods,
with only some chips also including the address setup time into equation...
[ bart: sl82c105 seems to be currently the only driver affected by this fix ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Sat, 3 Mar 2007 16:48:53 +0000 (17:48 +0100)]
piix/slc90e66: more tuneproc() fixing (take 2)
The tuneproc() method in both these drivers failed to set the drive's own speed.
Fix this by renaming the function and "wrapping around it" the new tuneproc()
method. Switch back to calling tuneproc() in the PIO fallback code.
While at it, also convert the rest of the PIO timing code into proper C. :-)
Has been kind of tested on SLC90E66. I'm too lazy to reboot my box and test
on ICH4... :-)
[ bart: I quickly tested it on ICH4. ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Tejun Heo [Sat, 3 Mar 2007 16:48:53 +0000 (17:48 +0100)]
ide: fix drive side 80c cable check, take 2
eighty_ninty_three() had word 93 validitity check but not the 80c bit
test itself (bit 13). This increases the chance of incorrect wire
detection especially because host side cable detection is often
unreliable and we sometimes soley depend on drive side cable
detection. Fix it.
[ bart: fix off-by-1 bit name in the patch description ]
Sergei Shtylyov [Sat, 3 Mar 2007 16:48:53 +0000 (17:48 +0100)]
cmd64x: fix PIO mode setup (take 3)
The driver's tuneproc() method fails to set the drive's own speed -- fix this
by renaming the function to cmd64x_tune_pio(), making it return the mode set,
and "wrapping" the new tuneproc() method around it; while at it, also get rid
of the non-working prefetch control code (filtering out related argument values
in the "wrapper"), remove redundant PIO5 mode limitation, make cmdprintk() give
more sensible mode info, and remove mention about the obsolete /proc/ interface.
Get rid of the broken config_chipset_for_pio() which always tried to set PIO4,
switch to always auto-tuning PIO instead.
Oh, and add the missing PIO5 support to the speedproc() method while at it. :-)
Warning: compile tested only -- getting to the real hardware isn't that easy...
On Tuesday 06 February 2007 22:11, Mikael Pettersson <mikpe@it.uu.se> wrote:
>
> Worked fine on my SPARC Ultra5 with a CMD646 IDE controller.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Sat, 3 Mar 2007 16:48:52 +0000 (17:48 +0100)]
alim15x3: fix PIO mode setup
The driver's tuneproc() method fails to set the drive's own speed -- fix this
by renaming the function to ali15x3_tune_pio() and "wrapping" the new tuneproc()
method around it and making it return the mode set, update the heading comment.
Also, setting PIO mode via the speedproc() method does not work due to passing
to the tuneproc() method's a mode number not biased by XFER_PIO_0 -- fix this
along with a typo in the heading comment...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Michael Krufky [Sat, 3 Mar 2007 12:10:43 +0000 (10:10 -0200)]
V4L/DVB (5260): Cx88-blackbird: allow usage of both 376836 and 262144 sized firmware images
This updates the cx88-blackbird driver to be able to use the new cx23416
firmware image released by Hauppauge Computer Works, while retaining
compatibility with the older firmware images.
cx2341x firmware can be downloaded at: http://dl.ivtvdriver.org/ivtv/firmware/
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Russell King [Sat, 3 Mar 2007 11:54:19 +0000 (11:54 +0000)]
[ARM] EBSA110: Work around build errors
Work around EBSA110 build errors by selecting NO_IOPORT. EBSA110
can't support an IO port to MMIO mapping mechanism because the
MMIO and IO port spaces have quite different and complex addressing
requirements.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dan Aloni [Sat, 3 Mar 2007 04:44:51 +0000 (20:44 -0800)]
[VLAN]: Avoid a 4-order allocation.
This patch splits the vlan_group struct into a multi-allocated struct. On
x86_64, the size of the original struct is a little more than 32KB, causing
a 4-order allocation, which is prune to problems caused by buddy-system
external fragmentation conditions.
I couldn't just use vmalloc() because vfree() cannot be called in the
softirq context of the RCU callback.
Signed-off-by: Dan Aloni <da-x@monatomic.org> Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Moore [Fri, 2 Mar 2007 21:19:02 +0000 (13:19 -0800)]
[NetLabel]: Verify sensitivity level has a valid CIPSO mapping
The current CIPSO engine has a problem where it does not verify that
the given sensitivity level has a valid CIPSO mapping when the "std"
CIPSO DOI type is used. The end result is that bad packets are sent
on the wire which should have never been sent in the first place.
This patch corrects this problem by verifying the sensitivity level
mapping similar to what is done with the category mapping. This patch
also changes the returned error code in this case to -EPERM to better
match what the category mapping verification code returns.
Signed-off-by: Paul Moore <paul.moore@hp.com> Acked-by: James Morris <jmorris@namei.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[PPPOE]: Key connections properly on local device.
It is based on the assumption that an interface's ifindex is basically
an alias for a local MAC address, so incoming packets now are matched
to sockets based on remote MAC, session id, and ifindex of the
interface the packet came in on/the socket was bound to by connect().
For relayed packets, the socket that's used for relaying is selected
based on destination MAC, session ID and the interface index of the
interface whose name currently matches the name requested by userspace
as the relaying source interface.
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Dong [Fri, 2 Mar 2007 20:37:26 +0000 (12:37 -0800)]
[NET]: Fix bugs in "Whether sock accept queue is full" checking
when I use linux TCP socket, and find there is a bug in function
sk_acceptq_is_full().
When a new SYN comes, TCP module first checks its validation. If valid,
send SYN,ACK to the client and add the sock to the syn hash table. Next
time if received the valid ACK for SYN,ACK from the client. server will
accept this connection and increase the sk->sk_ack_backlog -- which is
done in function tcp_check_req().We check wether acceptq is full in
function tcp_v4_syn_recv_sock().
Consider an example:
After listen(sockfd, 1) system call, sk->sk_max_ack_backlog is set to
1. As we know, sk->sk_ack_backlog is initialized to 0. Assuming accept()
system call is not invoked now.
1. 1st connection comes. invoke sk_acceptq_is_full(). sk-
>sk_ack_backlog=0 sk->sk_max_ack_backlog=1, function return 0 accept
this connection. Increase the sk->sk_ack_backlog
2. 2nd connection comes. invoke sk_acceptq_is_full(). sk-
>sk_ack_backlog=1 sk->sk_max_ack_backlog=1, function return 0 accept
this connection. Increase the sk->sk_ack_backlog
3. 3rd connection comes. invoke sk_acceptq_is_full(). sk-
>sk_ack_backlog=2 sk->sk_max_ack_backlog=1, function return 1. Refuse
this connection.
I think it has bugs. after listen system call. sk->sk_max_ack_backlog=1
but now it can accept 2 connections.
Signed-off-by: Wei Dong <weid@np.css.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6 / log