Andrew Morton [Thu, 10 Jan 2008 22:33:08 +0000 (14:33 -0800)]
[libata] pata_bf54x: checkpatch fixes
WARNING: line over 80 characters
#36: FILE: drivers/ata/pata_bf54x.c:1512:
+ while (bfin_port_info[board_idx].udma_mask>0 && udma_fsclk[udma_mode] > fsclk) {
ERROR: need spaces around that '>' (ctx:VxV)
#36: FILE: drivers/ata/pata_bf54x.c:1512:
+ while (bfin_port_info[board_idx].udma_mask>0 && udma_fsclk[udma_mode] > fsclk) {
^
total: 1 errors, 1 warnings, 19 lines checked
Your patch has style problems, please review. If any of these errors
are false positives report them to the maintainer, see
CHECKPATCH in MAINTAINERS.
Please run checkpatch prior to sending patches
Cc: Jeff Garzik <jeff@garzik.org> Cc: Sonic Zhang <sonic.zhang@analog.com> Cc: Tejun Heo <htejun@gmail.com> Cc: sonic zhang <sonic.adi@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Al Viro [Sat, 12 Jan 2008 14:16:14 +0000 (14:16 +0000)]
libata fixes for sparse-found problems
In pata_legacy and pata_winbond we've got bugs - cpu_to_le16() instead
of cpu_to_le32(). Fortunately, both affected suckers are VLB, thus
l-e-only, so we might get away with that unless we hit it with slop == 3
(hadn't checked if playing with badly aligned sg could trigger that).
Still buggy... Moreover, pata_legacy, pata_winbond and pata_qdi forgot to
initialize pad on the write side of 32bit case in their ->data_xfer().
Hopefully the hardware does't care, but still, sending uninitialized
data to it...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Linus Torvalds [Tue, 15 Jan 2008 17:23:51 +0000 (09:23 -0800)]
Fix ARM profiling/instrumentation configuration
Commit 09cadedbdc01f1a4bea1f427d4fb4642eaa19da9 ("Combine
instrumentation menus in kernel/Kconfig.instrumentation") broke ARM
profiling support, since ARM has some extra Kconfig options and doesn't
just use the common OPROFILE/KPROBES config options.
Rather than just revert the thing outright, or add ARM-specific
knowledge to the generic Kconfig.instrumentation file (where the only
and whole point was to be generic, not too architecture-specific), this
just makes ARM not use the generic version, since it doesn't suit it.
So create an arm-specific version of Kconfig.instrumentation instead,
and use that.
Acked-by: Ingo Molnar <mingo@elte.hu> Acked-by: Russell King <rmk+lkml@arm.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bernhard Walle [Tue, 15 Jan 2008 15:44:38 +0000 (16:44 +0100)]
x86: fix RTC_AIE with CONFIG_HPET_EMULATE_RTC
In the current code, RTC_AIE doesn't work if the RTC relies on
CONFIG_HPET_EMULATE_RTC because the code sets the RTC_AIE flag in
hpet_set_rtc_irq_bit(). The interrupt handles does accidentally check
for RTC_PIE and not RTC_AIE when comparing the time which was set in
hpet_set_alarm_time().
I now verified on a test system here that without the patch applied,
the attached test program fails on a system that has HPET with
2.6.24-rc7-default. That's not critical since I guess the problem has
been there for several kernel releases, but as the fix is quite
obvious.
Configuration is CONFIG_RTC=y and CONFIG_HPET_EMULATE_RTC=y.
Signed-off-by: Bernhard Walle <bwalle@suse.de> Acked-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Mike Frysinger [Tue, 15 Jan 2008 15:44:38 +0000 (16:44 +0100)]
x86: asm-x86/msr.h: pull in linux/types.h
Since the msr.h header uses types like __u32, it should pull in linux/types.h.
[ mingo@elte.hu: affects user-space that includes this header. We dont
actually like user-space including raw kernel headers but it's a
longstanding practice and it's easy for the kernel to be nice about
this. ]
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ingo Molnar [Tue, 15 Jan 2008 15:44:37 +0000 (16:44 +0100)]
x86: fix boot crash on HIGHMEM4G && SPARSEMEM
Denys Fedoryshchenko reported a bootup crash when he upgraded
his system from 3GB to 4GB RAM:
http://lkml.org/lkml/2008/1/7/9
the bug is due to HIGHMEM4G && SPARSEMEM kernels making pfn_to_page()
to return an invalid pointer when the pfn is in a memory hole. The
256 MB PCI aperture at the end of RAM was not mapped by sparsemem,
and hence the pfn was not valid. But set_highmem_pages_init() iterated
this range without checking the pfn's validity first.
this bug was probably present in the sparsemem code ever since sparsemem
has been introduced in v2.6.13. It was masked due to HIGHMEM64G using
larger memory regions in sparsemem_32.h:
which creates 1GB sparsemem regions instead of 64MB sparsemem regions.
So in practice we only ever created true sparsemem holes on x86 with
HIGHMEM4G - but that was rarely used by distros.
( btw., we could probably save 2MB of mem_map[]s on X86_PAE if we reduced
the sparsemem region size to 256 MB. )
Signed-off-by: Ingo Molnar <mingo@elte.hu> Acked-by: Thomas Gleixner <tglx@linutronix.de>
Paul Mackerras [Tue, 15 Jan 2008 06:29:33 +0000 (17:29 +1100)]
[POWERPC] Fix boot failure on POWER6
Commit 473980a99316c0e788bca50996375a2815124ce1 added a call to clear
the SLB shadow buffer before registering it. Unfortunately this means
that we clear out the entries that slb_initialize has previously set in
there. On POWER6, the hypervisor uses the SLB shadow buffer when doing
partition switches, and that means that after the next partition switch,
each non-boot CPU has no SLB entries to map the kernel text and data,
which causes it to crash.
This fixes it by reverting most of 473980a9 and instead clearing the
3rd entry explicitly in slb_initialize. This fixes the problem that 473980a9 was trying to solve, but without breaking POWER6.
Linus Torvalds [Tue, 15 Jan 2008 05:25:39 +0000 (21:25 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Cacheops.h: Fix typo.
[MIPS] Cobalt: Qube1 has no serial port so don't use it
[MIPS] Cobalt: Fix ethernet interrupts for RaQ1
[MIPS] Kconfig fixes for BCM47XX platform
Linus Torvalds [Tue, 15 Jan 2008 05:21:29 +0000 (21:21 -0800)]
Revert "writeback: introduce writeback_control.more_io to indicate more io"
This reverts commit 2e6883bdf49abd0e7f0d9b6297fc3be7ebb2250b, as
requested by Fengguang Wu. It's not quite fully baked yet, and while
there are patches around to fix the problems it caused, they should get
more testing. Says Fengguang: "I'll resend them both for -mm later on,
in a more complete patchset".
See
http://bugzilla.kernel.org/show_bug.cgi?id=9738
for some of this discussion.
Requested-by: Fengguang Wu <wfg@mail.ustc.edu.cn> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 5d2efba64b231a1733c4048d1708d77e07f26426 changed our iommu code
so that it always uses an iommu page size of 4kB. That means with our
current code, drivers may do a dma_map_sg() of a 64kB page and obtain
a dma_addr_t that is only 4k aligned.
This works fine in most cases except for some infiniband HW it seems,
where they tell the HW about the page size and it ignores the low bits
of the DMA address.
This works around it by making our IOMMU code enforce a PAGE_SIZE alignment
for mappings of objects that are page aligned in the first place and whose
size is larger or equal to a page.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
After 9b8e8de7, manage_start_stop configuration depends on valid ATA
device. Move it into ata_scsi_dev_config(). This was detected by the
coverity checker.
Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Adrian Bunk <bunk@kernel.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Sun, 13 Jan 2008 05:04:16 +0000 (14:04 +0900)]
sata_sil24: freeze on non-dev errors reported via CERR
CERR reports errors detected during executing a command. This doesn't
mean the error is tied to the command and can be recovered by just
issuing it again. Many of the errors are fatal port-wide connditions
including HSM violation, host bus error and ATA bus error and require
freezing and port reset.
The freezing part wasn't implemented previously. This used to be okay
because port resets were scheduled anyway and EH eventually resets and
recovers the port. With PMP support added, this is no longer true.
The error condition and recover actions are attributed to the fan-out
port and the host port condition isn't properly recovered leading to
EH failures.
This patch makes CERR errors which require resets to freeze the port.
This will force host port reset and proper recovery.
Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Andrew Ryder <tireman@shaw.ca> Signed-off-by: Jeff Garzik <jeff@garzik.org>
[MIPS] Cobalt: Qube1 has no serial port so don't use it
Because Qube1 doesn't have a serial chip waiting for transmit fifo empty
takes forever, which isn't a good idea. No prom_putchar/early console
for Qube1 fixes this.
Aurelien Jarno [Tue, 11 Dec 2007 10:30:34 +0000 (11:30 +0100)]
[MIPS] Kconfig fixes for BCM47XX platform
The patch below fixes two problems for Kconfig on the BCM47xx platform:
- arch/mips/bcm47xx/gpio.c uses ssb_extif_* functions. Selecting
SSB_DRIVER_EXTIF makes sure those functions are available.
- arch/mips/pci/pci.c needs, when enabled, platform specific functions,
which are defined when SSB_PCICORE_HOSTMODE is enabled.
Oleg Nesterov [Mon, 14 Jan 2008 21:02:37 +0000 (00:02 +0300)]
fix the "remove task_ppid_nr_ns" commit
Commit 84427eaef1fb91704c7112bdb598c810003b99f3 (remove task_ppid_nr_ns)
moved the task_tgid_nr_ns(task->real_parent) outside of lock_task_sighand().
This is wrong, ->real_parent could be freed/reused.
Both ->parent/real_parent point to nothing after __exit_signal() because
we remove the child from ->children list, and thus the child can't be
reparented when its parent exits.
rcu_read_lock() protects ->parent/real_parent, but _only_ if we know it was
valid before we take rcu lock.
Linus Torvalds [Mon, 14 Jan 2008 17:10:45 +0000 (09:10 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: improve Kconfig help entries for HP Jornada devices
Input: pass EV_PWR events to event handlers
Input: spitzkbd - fix suspend key handling
gameport: don't export functions that are static inline
Input: jornada680_kbd - fix default keymap
Input: Handle EV_PWR type of input caps in input_set_capability.
Jesper Nilsson [Mon, 14 Jan 2008 08:55:23 +0000 (00:55 -0800)]
CRIS v10: kernel/time.c needs to include linux/vmstat.h to compile
This fixes compile error when nr_free_pages() from linux/swap.h
expands to global_page_state(NR_FREE_PAGES), but linux/vmstat.h isn't
included to declare global_page_state().
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com> Cc: Mikael Starvik <mikael.starvik@axis.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jesper Nilsson [Mon, 14 Jan 2008 08:55:22 +0000 (00:55 -0800)]
CRIS v10: correct do_signal to fix oops and clean up signal handling in general
This fixes a kernel panic on boot due to do_signal not being compatible
with it's callers.
- do_signal now returns void, and does not have the previous signal set
as a parameter.
- Remove sys_rt_sigsuspend, we can use the common one instead.
- Change sys_sigsuspend to be more like x86, don't call do_signal here.
- handle_signal, setup_frame and setup_rt_frame now return -EFAULT
if we've delivered a segfault, which is used by callers to perform
necessary cleanup.
- Break long lines, correct whitespace and formatting errors.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com> Cc: Mikael Starvik <mikael.starvik@axis.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Krzysztof Helt [Mon, 14 Jan 2008 08:55:20 +0000 (00:55 -0800)]
s3c2410fb: fix incorrect argument type in resume function
Fix wrong pointer type passed into the s3c2410fb_init_registers()
function.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ken Chen [Mon, 14 Jan 2008 08:55:19 +0000 (00:55 -0800)]
hugetlbfs: fix quota leak
In the error path of both shared and private hugetlb page allocation,
the file system quota is never undone, leading to fs quota leak. Fix
them up.
[akpm@linux-foundation.org: cleanup, micro-optimise] Signed-off-by: Ken Chen <kenchen@google.com> Acked-by: Adam Litke <agl@us.ibm.com> Cc: David Gibson <david@gibson.dropbear.id.au> Cc: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Mon, 14 Jan 2008 08:55:18 +0000 (00:55 -0800)]
advansys: fix section mismatch warning
Fix section mismatch warning:
WARNING: vmlinux.o(.exit.text+0x152a): Section mismatch: reference to .init.data:_asc_def_iop_base (between 'advansys_isa_remove' and 'advansys_exit')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: Matthew Wilcox <willy@debian.org> Cc: James Bottomley <James.Bottomley@steeleye.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adrian Bunk [Mon, 14 Jan 2008 08:55:16 +0000 (00:55 -0800)]
scsi/qla2xxx/qla_os.c section fix
WARNING: vmlinux.o(.text+0x2a4462): Section mismatch: reference to .exit.text:qla2x00_remove_one (between 'qla2xxx_pci_error_detected' and 'qla2x00_stop_timer')
qla2x00_remove_one() mustn't be __devexit since it's called from
qla2xxx_pci_error_detected().
Signed-off-by: Adrian Bunk <bunk@kernel.org> Acked-by: Seokmann Ju <seokmann.ju@qlogic.com> Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Cc: Randy Dunlap <randy.dunlap@oracle.com> Cc: James Bottomley <James.Bottomley@steeleye.com> Acked-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andy Wingo [Mon, 14 Jan 2008 08:55:15 +0000 (00:55 -0800)]
macintosh: fix fabrication of caplock key events
If the user has turned on the "restore_caplock_events" parameter, the
code mangles the capslock events correctly, then erroneously ignores
those events. Fix logic to allow correct fallthrough.
Signed-off-by: Andy Wingo <wingo@pobox.com> Acked-by: Andrew McNabb <amcnabb@mcnabbs.org> Cc: Dmitry Torokhov <dtor@mail.ru> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
cc: Paul Mackerras <paulus@samba.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
quicklists: Only consider memory that can be used with GFP_KERNEL
Quicklists calculates the size of the quicklists based on the number of
free pages. This must be the number of free pages that can be allocated
with GFP_KERNEL. node_page_state() includes the pages in ZONE_HIGHMEM and
ZONE_MOVABLE which may lead the quicklists to become too large causing OOM.
Signed-off-by: Christoph Lameter <clameter@sgi.com> Tested-by: Dhaval Giani <dhaval@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Smith [Mon, 14 Jan 2008 08:55:12 +0000 (00:55 -0800)]
TPM: fix suspend and resume failure
The savestate command structure was being overwritten by the result of
running the TPM_SaveState command after one run, so make it a local
variable to the function instead of a global variable that gets
overwritten.
Acked-by: Pavel Machek <pavel@ucw.cz> Cc: Kent Yoder <shpedoikal@gmail.com> Cc: Marcel Selhorst <tpm@selhorst.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Steven Rostedt [Mon, 14 Jan 2008 08:55:10 +0000 (00:55 -0800)]
Kick CPUS that might be sleeping in cpus_idle_wait
Sometimes cpu_idle_wait gets stuck because it might miss CPUS that are
already in idle, have no tasks waiting to run and have no interrupts going
to them. This is common on bootup when switching cpu idle governors.
This patch gives those CPUS that don't check in an IPI kick.
Background:
-----------
I notice this while developing the mcount patches, that every once in a
while the system would hang. Looking deeper, the hang was always at boot
up when registering init_menu of the cpu_idle menu governor. Talking
with Thomas Gliexner, we discovered that one of the CPUS had no timer
events scheduled for it and it was in idle (running with NO_HZ). So the
CPU would not set the cpu_idle_state bit.
Hitting sysrq-t a few times would eventually route the interrupt to the
stuck CPU and the system would continue.
Note, I would have used the PDA isidle but that is set after the
cpu_idle_state bit is cleared, and would leave a window open where we
may miss being kicked.
hmm, looking closer at this, we still have a small race window between
clearing the cpu_idle_state and disabling interrupts (hence the RFC).
CPU0: CPU 1:
--------- ---------
cpu_idle_wait(): cpu_idle():
| __cpu_cpu_var(is_idle) = 1;
| if (__get_cpu_var(cpu_idle_state)) /* == 0 */
per_cpu(cpu_idle_state, 1) = 1; |
if (per_cpu(is_idle, 1)) /* == 1 */ |
smp_call_function(1) |
| receives ipi and runs do_nothing.
wait on map == empty idle();
/* waits forever */
So really we need interrupts off for most of this then. One might think
that we could simply clear the cpu_idle_state from do_nothing, but I'm
assuming that cpu_idle governors can be removed, and this might cause a
race that a governor might be used after the module was removed.
Venki said:
I think your RFC patch is the right solution here. As I see it, there is
no race with your RFC patch. As long as you call a dummy smp_call_function
on all CPUs, we should be OK. We can get rid of cpu_idle_state and the
current wait forever logic altogether with dummy smp_call_function. And so
there wont be any wait forever scenario.
The whole point of cpu_idle_wait() is to make all CPUs come out of idle
loop atleast once. The caller will use cpu_idle_wait something like this.
// Want to change idle handler
- Switch global idle handler to always present default_idle
- call cpu_idle_wait so that all cpus come out of idle for an instant
and stop using old idle pointer and start using default idle
- Change the idle handler to a new handler
- optional cpu_idle_wait if you want all cpus to start using the new
handler immediately.
Maybe the below 1s patch is safe bet for .24. But for .25, I would say we
just replace all complicated logic by simple dummy smp_call_function and
remove cpu_idle_state altogether.
Signed-off-by: Steven Rostedt <srostedt@redhat.com> Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Acked-by: Ingo Molnar <mingo@elte.hu> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: Andi Kleen <ak@suse.de> Cc: Len Brown <lenb@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Evgeniy Polyakov [Mon, 14 Jan 2008 08:55:08 +0000 (00:55 -0800)]
w1: decrement slave counter only in ->release() callback
Decrement the slave counter only in ->release() callback instead of both
in ->release() and w1 control.
Patch is based on debug work and preliminary patch made by Henri Laakso.
Henri noticed in debug that this counter becomes negative after w1 slave
device is physically removed.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Cc: Henri Laakso <henri.laakso@wapice.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rusty Russell [Mon, 14 Jan 2008 08:55:03 +0000 (00:55 -0800)]
modules: de-mutex more symbol lookup paths in the module code
Kyle McMartin reports sysrq_timer_list_show() can hit the module mutex
from hard interrupt context. These paths don't need to though, since we
long ago changed all the module list manipulation to occur via
stop_machine().
Disabling preemption is enough.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: Ingo Molnar <mingo@elte.hu> Cc: Kyle McMartin <kyle@mcmartin.ca> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 13 Jan 2008 18:02:26 +0000 (10:02 -0800)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
spidernet MAINTAINERship update
sky2: remove check for PCI wakeup setting from BIOS
sky2: large memory workaround.
fs_enet: check for phydev existence in the ethtool handlers
[usb netdev] asix: fix regression
r8169: fix missing loop variable increment
ip1000: menu location change
Fixed a small typo in the loopback driver
3c509: PnP resource management fix
netxen: fix byte-swapping in tx and rx
netxen: optimize tx handling
netxen: stop second phy correctly
netxen: update driver version
netxen: update MAINTAINERS
endianness noise in tulip_core
de4x5 fixes
xircom_cb endianness fixes
rt2x00: Put 802.11 data on 4 byte boundary
rt2x00: Corectly initialize rt2500usb MAC
rt2x00: Allow rt61 to catch up after a missing tx report
Linus Torvalds [Sun, 13 Jan 2008 18:01:45 +0000 (10:01 -0800)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fix CPU hotplug when using the SLB shadow buffer
[POWERPC] efika: add phy-handle property for fec_mpc52xx
Linus Torvalds [Sun, 13 Jan 2008 17:58:22 +0000 (09:58 -0800)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
pnpacpi: print resource shortage message only once
PM: ACPI and APM must not be enabled at the same time
ACPI: apply quirk_ich6_lpc_acpi to more ICH8 and ICH9
ACPICA: fix acpi_serialize hang regression
ACPI : Not register gsi for PCI IDE controller in legacy mode
ACPI: Reintroduce run time configurable max_cstate for !CPU_IDLE case
ACPI: Make sysfs interface in ACPI power optional.
ACPI: EC: Enable boot EC before bus_scan
increase PNP_MAX_PORT to 40 from 24
NeilBrown [Fri, 11 Jan 2008 22:06:52 +0000 (17:06 -0500)]
knfsd: Allow NFSv2/3 WRITE calls to succeed when krb5i etc is used.
When RPCSEC/GSS and krb5i is used, requests are padded, typically to a multiple
of 8 bytes. This can make the request look slightly longer than it
really is.
As of
f34b95689d2ce001c "The NFSv2/NFSv3 server does not handle zero
length WRITE request correctly",
the xdr decode routines for NFSv2 and NFSv3 reject requests that aren't
the right length, so krb5i (for example) WRITE requests can get lost.
This patch relaxes the appropriate test and enhances the related comment.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu> Cc: Peter Staubach <staubach@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Roland McGrath [Thu, 10 Jan 2008 20:52:04 +0000 (12:52 -0800)]
remove task_ppid_nr_ns
task_ppid_nr_ns is called in three places. One of these should never
have called it. In the other two, using it broke the existing
semantics. This was presumably accidental. If the function had not
been there, it would have been much more obvious to the eye that those
patches were changing the behavior. We don't need this function.
In task_state, the pid of the ptracer is not the ppid of the ptracer.
In do_task_stat, ppid is the tgid of the real_parent, not its pid.
I also moved the call outside of lock_task_sighand, since it doesn't
need it.
In sys_getppid, ppid is the tgid of the real_parent, not its pid.
Signed-off-by: Roland McGrath <roland@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David S. Miller [Wed, 9 Jan 2008 13:09:06 +0000 (05:09 -0800)]
[SPARC]: Make gettimeofday() monotonic again.
When we switched away from the optimized C version
things stopped being monotonic.
The problem is that if we run this with interrupts disabled, we can
see the interrupt pending because the counter reached the limit value.
When this happens the counter has bit 31 set, and the low bits start
counting again from zero.
Reported by Martin Habets.
Signed-off-by: David S. Miller <davem@davemloft.net>
Len Brown [Sat, 12 Jan 2008 22:56:36 +0000 (17:56 -0500)]
pnpacpi: print resource shortage message only once
pnpacpi: exceeded the max number of IO resources: 40
While this message is a real error and should thus
remain KERN_ERR (even a new dmesg line is seen as a regression
by some, since it was not printed in 2.6.23...) it is certainly
impolite to print this warning 50 times should you happen to
have the oddball system with 90 io resources under a device...
So print the warning just once.
In 2.6.25 we'll get rid of the limits altogether
and these warnings will vanish with them.
sky2: remove check for PCI wakeup setting from BIOS
The driver checks status of PCI power management to mark
default setting of Wake On Lan. On some systems this works, but often
it reports a that WOL is disabled when it isn't.
This patch gets rid of that check and just reports the wake on
lan status based on the hardware capablity.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch might fix problems with 4G or more of memory.
It stops the driver from doing a small optimization for Tx and Rx,
and instead always sets the high-page on tx/rx descriptors.
Linus Torvalds [Sat, 12 Jan 2008 22:06:34 +0000 (14:06 -0800)]
Use access mode instead of open flags to determine needed permissions
Way back when (in commit 834f2a4a1554dc5b2598038b3fe8703defcbe467, aka
"VFS: Allow the filesystem to return a full file pointer on open intent"
to be exact), Trond changed the open logic to keep track of the original
flags to a file open, in order to pass down the the intent of a dentry
lookup to the low-level filesystem.
However, when doing that reorganization, it changed the meaning of
namei_flags, and thus inadvertently changed the test of access mode for
directories (and RO filesystem) to use the wrong flag. So fix those
test back to use access mode ("acc_mode") rather than the open flag
("flag").
Issue noticed by Bill Roman at Datalight.
Reported-and-tested-by: Bill Roman <bill.roman@datalight.com> Acked-by: Trond Myklebust <Trond.Myklebust@netapp.com> Acked-by: Al Viro <viro@ZenIV.linux.org.uk> Cc: Christoph Hellwig <hch@lst.de> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Russ Dill [Thu, 10 Jan 2008 04:32:07 +0000 (21:32 -0700)]
[usb netdev] asix: fix regression
51bf2976b55d07f9daae9697a0a3ac9f58abcedc caused a regression in the asix
usbnet driver. usb_control_msg returns the number of bytes read on
success, not 0. Tested with NETGEAR FA120.
Signed-off-by: Russ Dill <Russ.Dill@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move the ip1000 driver into the expected place for gigabit cards
in the configuration menu structure. It should be under the gigabit
cards, not at the top level.
Signed-off-by: Stephen Hemminger <stephen.hemminger@vyatta.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Krzysztof Helt [Thu, 27 Dec 2007 08:54:04 +0000 (09:54 +0100)]
3c509: PnP resource management fix
In order to release PnP resources a card type must be set to EL3_PNP.
Previously, it was never set hence the PnP resources were not
released and device was left in incorrect state.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Dhananjay Phadke [Mon, 31 Dec 2007 18:08:57 +0000 (10:08 -0800)]
netxen: fix byte-swapping in tx and rx
Here's the reworked patch.
This cleans up some unnecessary byte-swapping while setting up tx and
interpreting rx desc. The 64 bit rx status data should be converted
to host endian format only once and the macros just need to extract
bitfields.
This saves a spate of interrupts on pseries blades caused by buggy
(non) processing rx status ring.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
netxen driver allows limited number of threads simultaneously posting
skb's in tx ring. If transmit slot is unavailable, driver calls
schedule() or loops in xmit_frame().
This patch returns TX_BUSY and lets the stack reschedule the packet if
transmit slot is unavailable. Also removes unnecessary check for tx
timeout in the driver itself, the network stack does that anyway.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Al Viro [Sun, 23 Dec 2007 20:01:04 +0000 (20:01 +0000)]
de4x5 fixes
* (trivial) endianness annotations
* don't bother with del_timer() from the inside of timer handler itself
* disable_ast() really ought to do del_timer_sync(), not del_timer()
* clean the timer handling in general.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jeff Garzik <jeff@garzik.org>
The bridge code incorrectly causes two POST_ROUTING hook invocations
for DNATed packets that end up on the same bridge device. This
happens because packets with a changed destination address are passed
to dst_output() to make them go through the neighbour output function
again to build a new destination MAC address, before they will continue
through the IP hooks simulated by bridge netfilter.
The resulting hook order is:
PREROUTING (bridge netfilter)
POSTROUTING (dst_output -> ip_output)
FORWARD (bridge netfilter)
POSTROUTING (bridge netfilter)
The deferred hooks used to abort the first POST_ROUTING invocation,
but since the only thing bridge netfilter actually really wants is
a new MAC address, we can avoid going through the IP stack completely
by simply calling the neighbour output function directly.
Tested, reported and lots of data provided by: Damien Thebault <damien.thebault@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 11 Jan 2008 19:48:00 +0000 (11:48 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Replace 40c7869b693b18412491fdcff64682215b739f9e kludge
[MIPS] Lasat: Fix built in separate object directory.
[MIPS] Malta: Fix software reset on big endian
[MIPS] pnx8xxx: move to clocksource
[MIPS] Wrong CONFIG option prevents setup of DMA zone.
This change avoids the deadlock by moving the acquire_console_sem()
out of ps3fb_sync(), and puts it into the two other callsites, leaving
ps3fb_release() to call ps3fb_sync() without the console semaphore.
[Geert]
- Corrected call sequence above
- ps3fb_release() may be called with and without console_sem held. This is an
inconsistency that should be fixed at the fb level, but for now, try to
acquire console_sem in ps3fb_release().
I think it's safer to let ps3fb_release() try to acquire console_sem and
not refresh the screen if it fails, than to call ps3fb_sync() without
holding console_sem, as ps3fb_par may be modified at the same time, causing
crashes or lockups.
Besides, ps3fb_release() only calls ps3fb_sync() to refresh the screen
when display flipping is disabled, which is an uncommon case (except during
shutdown/kexec).
Signed-off-by: Jeremy Kerr <jk@ozlabs.org> Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeremy Kerr [Fri, 11 Jan 2008 13:27:10 +0000 (14:27 +0100)]
ps3fb: prevent use after free of fb_info
In ps3fb_shutdown, freeing the framebuffer will cause fb_info (in
dev->core.driver_data) to be free()ed, which we potentially access
from the ps3fbd kthread.
This change frees the framebuffer after stopping the ps3fbd kthread.
Linus Torvalds [Fri, 11 Jan 2008 19:44:59 +0000 (11:44 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
blktrace: kill the unneeded initcall
block: fix blktrace timestamps
loop: fix bad bio_alloc() nr_iovec request
Don't blatt first element of prv in sg_chain()
Massimo Cirillo [Fri, 11 Jan 2008 10:24:11 +0000 (10:24 +0000)]
cache invalidation error for buffered write
The bug causes corruptions of data read from flash.
The original code performs cache invalidation from "adr" to "adr + len"
in do_write_buffer(). Since len and adr could be updated in the code
before invalidation - it causes improper setting of cache invalidation
regions.
Signed-off-by: Massimo Cirillo <maxcir@gmail.com> Signed-off-by: Giuseppe D'Eliseo <giuseppedeliseo@gmail.com> Acked-by: Nicolas Pitre <nico@cam.org> Acked-by: Jörn Engel <joern@logfs.org> Signed-off-by: David Woohouse <dwmw2@infradead.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Len Brown [Thu, 13 Dec 2007 22:38:03 +0000 (17:38 -0500)]
PM: ACPI and APM must not be enabled at the same time
ACPI and APM used "pm_active" to guarantee that
they would not be simultaneously active.
But pm_active was recently moved under CONFIG_PM_LEGACY,
so that without CONFIG_PM_LEGACY, pm_active became a NOP --
allowing ACPI and APM to both be simultaneously enabled.
This caused unpredictable results, including boot hangs.
Further, the code under CONFIG_PM_LEGACY is scheduled
for removal.
So replace pm_active with pm_flags.
pm_flags depends only on CONFIG_PM,
which is present for both CONFIG_APM and CONFIG_ACPI.
http://bugzilla.kernel.org/show_bug.cgi?id=9194
Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
projects / linux-2.6 / log