Roland McGrath [Thu, 10 Jul 2008 21:50:39 +0000 (14:50 -0700)]
x86_64: fix delayed signals
On three of the several paths in entry_64.S that call
do_notify_resume() on the way back to user mode, we fail to properly
check again for newly-arrived work that requires another call to
do_notify_resume() before going to user mode. These paths set the
mask to check only _TIF_NEED_RESCHED, but this is wrong. The other
paths that lead to do_notify_resume() do this correctly already, and
entry_32.S does it correctly in all cases.
All paths back to user mode have to check all the _TIF_WORK_MASK
flags at the last possible stage, with interrupts disabled.
Otherwise, we miss any flags (TIF_SIGPENDING for example) that were
set any time after we entered do_notify_resume(). More work flags
can be set (or left set) synchronously inside do_notify_resume(), as
TIF_SIGPENDING can be, or asynchronously by interrupts or other CPUs
(which then send an asynchronous interrupt).
There are many different scenarios that could hit this bug, most of
them races. The simplest one to demonstrate does not require any
race: when one signal has done handler setup at the check before
returning from a syscall, and there is another signal pending that
should be handled. The second signal's handler should interrupt the
first signal handler before it actually starts (so the interrupted PC
is still at the handler's entry point). Instead, it runs away until
the next kernel entry (next syscall, tick, etc).
This test behaves correctly on 32-bit kernels, and fails on 64-bit
(either 32-bit or 64-bit test binary). With this fix, it works.
x86: Recover timer_ack lost in the merge of the NMI watchdog
In the course of the recent unification of the NMI watchdog an assignment
to timer_ack to switch off unnecesary POLL commands to the 8259A in the
case of a watchdog failure has been accidentally removed. The statement
used to be limited to the 32-bit variation as since the rewrite of the
timer code it has been relevant for the 82489DX only. This change brings
it back.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
There is no such entity as ISA IRQ2. The ACPI spec does not make it
explicitly clear, but does not preclude it either -- all it says is ISA
legacy interrupts are identity mapped by default (subject to overrides),
but it does not state whether IRQ2 exists or not. As a result if there is
no IRQ0 override, then IRQ2 is normally initialised as an ISA interrupt,
which implies an edge-triggered line, which is unmasked by default as this
is what we do for edge-triggered I/O APIC interrupts so as not to miss an
edge.
To the best of my knowledge it is useless, as IRQ2 has not been in use
since the PC/AT as back then it was taken by the 8259A cascade interrupt
to the slave, with the line position in the slot rerouted to newly-created
IRQ9. No device could thus make use of this line with the pair of 8259A
chips. Now in theory INTIN2 of the I/O APIC may be usable, but the
interrupt of the device wired to it would not be available in the PIC mode
at all, so I seriously doubt if anybody decided to reuse it for a regular
device.
However there are two common uses of INTIN2. One is for IRQ0, with an
ACPI interrupt override (or its equivalent in the MP table). But in this
case IRQ2 is gone entirely with INTIN0 left vacant. The other one is for
an 8959A ExtINTA cascade. In this case IRQ0 goes to INTIN0 and if ACPI is
used INTIN2 is assumed to be IRQ2 (there is no override and ACPI has no
way to report ExtINTA interrupts). This is where a problem happens.
The problem is INTIN2 is configured as a native APIC interrupt, with a
vector assigned and the mask cleared. And the line may indeed get active
and inject interrupts if the master 8959A has its timer interrupt enabled
(it might happen for other interrupts too, but they are normally masked in
the process of rerouting them to the I/O APIC). There are two cases where
it will happen:
* When the I/O APIC NMI watchdog is enabled. This is actually a misnomer
as the watchdog pulses are delivered through the 8259A to the LINT0
inputs of all the local APICs in the system. The implication is the
output of the master 8259A goes high and low repeatedly, signalling
interrupts to INTIN2 which is enabled too!
[The origin of the name is I think for a brief period during the
development we had a capability in our code to configure the watchdog to
use an I/O APIC input; that would be INTIN2 in this scenario.]
* When the native route of IRQ0 via INTIN0 fails for whatever reason -- as
it happens with the system considered here. In this scenario the timer
pulse is delivered through the 8259A to LINT0 input of the local APIC of
the bootstrap processor, quite similarly to how is done for the watchdog
described above. The result is, again, INTIN2 receives these pulses
too. Rafael's system used to escape this scenario, because an incorrect
IRQ0 override would occupy INTIN2 and prevent it from being unmasked.
My conclusion is IRQ2 should be excluded from configuration in all the
cases and the current exception for ACPI systems should be lifted. The
reason being the exception not only being useless, but harmful as well.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Cc: Andreas Herrmann <andreas.herrmann3@amd.com> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Unlike the 32-bit one, the 64-bit variation of the LVT0 setup code for
the "8259A Virtual Wire" through the local APIC timer configuration does
not fully configure the relevant irq_chip structure. Instead it relies on
the preceding I/O APIC code to have set it up, which does not happen if
the I/O APIC variants have not been tried.
The patch includes corresponding changes to the 32-bit variation too
which make them both the same, barring a small syntactic difference
involving sequence of functions in the source. That should work as an aid
with the upcoming merge.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Cc: Andreas Herrmann <andreas.herrmann3@amd.com> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Ingo Molnar <mingo@elte.hu>
IRQ0 is edge-triggered, but the "8259A Virtual Wire" through the local
APIC configuration in the 32-bit version uses the "fasteoi" handler
suitable for level-triggered APIC interrupt. Rewrite code so that the
"edge" handler is used. The 64-bit version uses different code and is
unaffected.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Cc: Andreas Herrmann <andreas.herrmann3@amd.com> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Glauber Costa [Thu, 10 Jul 2008 18:17:53 +0000 (15:17 -0300)]
x86: use AS_CFI instead of UNWIND_INFO
In dwarf2_32.h, test for CONFIG_AS_CFI instead of
CONFIG_UNWIND_INFO. Turns out that searching for UNWIND_INFO
returns no match in any Kconfig or Makefile, so we're really
just throwing everything away regarding dwarf frames for i386.
The test that generates CONFIG_AS_CFI does not have anything
x86_64-specific, and right now, checking V=1 builds shows me
that the flags is there anyway, although unused.
Signed-off-by: Glauber Costa <gcosta@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
eventually causing init to die and panic the system:
Kernel panic - not syncing: Attempted to kill init!
Pid: 1, comm: init Not tainted 2.6.26-rc9-tip #13878
after a maratonic bisection session, the bad commit turned out to be:
| b7675791859075418199c7af86a116ea34eaf5bd is first bad commit
| commit b7675791859075418199c7af86a116ea34eaf5bd
| Author: Jeremy Fitzhardinge <jeremy@goop.org>
| Date: Wed Jun 25 00:19:00 2008 -0400
|
| x86: remove open-coded save/load segment operations
|
| This removes a pile of buggy open-coded implementations of savesegment
| and loadsegment.
after some more bisection of this patch itself, it turns out that what
makes the difference are the savesegment() changes to __switch_to().
Taking a look at this portion of arch/x86/kernel/process_64.o revealed
this crutial difference:
note the "m" modifier - it allows GCC to generate the segment move
into a memory operand as well.
But regarding segment operands there's a subtle detail in the x86
instruction set: the above 16-bit moves are zero-extend, but only
if it goes to a register.
If it goes to a memory operand, -0x34(%rbp) in the above case, there's
no zero-extend to 32-bit and the instruction will only save 16 bits
instead of the intended 32-bit.
The other 16 bits is random data - which can cause problems when that
value is used later on.
The solution is to only allow segment operands to go to registers.
This fix allows my test-system to boot up without crashing.
x86_64: add pseudo-features for 32-bit compat syscall
Add pseudo-feature bits to describe whether the CPU supports sysenter
and/or syscall from ia32-compat userspace. This removes a hardcoded
test in vdso32-setup.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Gas 2.15 complains about 32-bit registers being used in lea.
AS arch/x86/lib/copy_user_64.o
/local/scratch-2/jeremy/hg/xen/paravirt/linux/arch/x86/lib/copy_user_64.S: Assembler messages:
/local/scratch-2/jeremy/hg/xen/paravirt/linux/arch/x86/lib/copy_user_64.S:188: Error: `(%edx,%ecx,8)' is not a valid 64 bit base/index expression
/local/scratch-2/jeremy/hg/xen/paravirt/linux/arch/x86/lib/copy_user_64.S:257: Error: `(%edx,%ecx,8)' is not a valid 64 bit base/index expression
AS arch/x86/lib/copy_user_nocache_64.o
/local/scratch-2/jeremy/hg/xen/paravirt/linux/arch/x86/lib/copy_user_nocache_64.S: Assembler messages:
/local/scratch-2/jeremy/hg/xen/paravirt/linux/arch/x86/lib/copy_user_nocache_64.S:107: Error: `(%edx,%ecx,8)' is not a valid 64 bit base/index expression
arch/x86/kernel/built-in.o: In function `visws_early_detect':
: undefined reference to `mach_get_smp_config_quirk'
arch/x86/kernel/built-in.o: In function `visws_early_detect':
: undefined reference to `mach_find_smp_config_quirk'
arch/x86/kernel/visws_quirks.c: In function ‘visws_early_detect’:
arch/x86/kernel/visws_quirks.c:293: error: ‘no_broadcast’ undeclared (first use in this function)
arch/x86/kernel/visws_quirks.c:293: error: (Each undeclared identifier is reported only once
arch/x86/kernel/visws_quirks.c:293: error: for each function it appears in.)
make[1]: *** [arch/x86/kernel/visws_quirks.o] Error 1
make: *** [arch/x86/kernel/visws_quirks.o] Error 2
Robert Richter [Thu, 10 Jul 2008 16:58:24 +0000 (18:58 +0200)]
x86/pci merge: fixing numaq initialization
Patch d49c4288 (tip/x86/mpparse) introduced some changes in calling
subsys_init calls if CONFIG_X86_NUMAQ option is set. This patch
updates subsystem initalization according to this changes.
Signed-off-by: Robert Richter <robert.richter@amd.com> Cc: Robert Richter <robert.richter@amd.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
x86, VisWS: turn into generic arch, copy visws files
copy arch/x86/mach-visws/setup_visws.c, apic_visws.c and traps_visws.c
files to arch/x86/kernel/, in preparation of the switchover to a
non-subarch setup for VISWS.
x86, VisWS: turn into generic arch, eliminate include/asm-x86/mach-visws/smpboot_hooks.h
now that include/asm-x86/mach-visws/smpboot_hooks.h equals
to the default file in ../mach-default/smpboot_hooks.h, simply
include it instead of maintaining a copy.
x86: I/O APIC: Add a 64-bit variation of replace_pin_at_irq()
When an interrupt is rerouted to a different I/O APIC pin the relevant
entry of the irq_2_pin list should get updated accordingly so that
operations are performed on the correct redirection entry.
This is already done by the 32-bit variation of the code and here is a
complementing 64-bit implementation. Should make someone's decision less
tough when merging the two. ;)
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
AMD_IOMMU should depend on IOMMU_HELPER since they are the IOMMU
helper functions. SWIOTLB requires IOMMU_HELPER so declaring that
AMD_IOMMU depends on SWIOTLB properly fixes the problems.
Switch copy_user_generic_string(), copy_user_generic_unrolled() and
__copy_user_nocache() from custom tail handlers to generic
copy_user_tail_handle().
This patch removes the ordering dependency. There is now only one
subsys_initcall function that contains subsystem initialization code
with a defined order.
arch/x86/kernel/acpi/boot.c: In function ‘dmi_ignore_irq0_timer_override’:
arch/x86/kernel/acpi/boot.c:1443: error: implicit declaration of function ‘force_mask_ioapic_irq_2’
The problems are that, with the ACPI vs timer overring issue _fixed_,
after using the box for some time (between several seconds and 1 hour, at
random) processes get very high CPU loads (once I've got X using 107% of
the CPU, for example) and the system becomes unresponsive, as though there
were interrupts lost or something similar.
Andreas Herrman reproduced similar problems:
> Ok, now I've reproduced the stability problem.
> - Using tip/master,
> - reverting e38502eb8aa82314d5ab0eba45f50e6790dadd88 and
> - applying your patch from this posting
> http://marc.info/?l=linux-kernel&m=121539354224562&w=4
>
> Starting X, firefox, gimp, tuxpaint and doing some drawing in tuxpaint
> results in a slow system. Drawing is almost not possible anymore --
> Selections of new colors, cursors etc. is performed with huge delay
> if it's performed at all.
>
> BTW, the code sets up timer IRQ as Virtual Wire IRQ:
>
> Jul 8 14:57:58 kodscha IO-APIC (apicid-pin) 2-22, 2-23 not connected.
> Jul 8 14:57:58 kodscha ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
> Jul 8 14:57:58 kodscha ...trying to set up timer as Virtual Wire IRQ... works.
>
> and both INT0 and INT2 of IOAPIC are masked:
>
> Jul 8 14:57:58 kodscha NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect:
> Jul 8 14:57:58 kodscha 00 000 1 0 0 0 0 0 0 00
> Jul 8 14:57:58 kodscha 01 003 0 0 0 0 0 1 1 31
> Jul 8 14:57:58 kodscha 02 003 1 0 0 0 0 0 0 30
>
> I've also seen strange CPU utilization -- with syslog-ng:
>
> top - 15:33:06 up 35 min, 4 users, load average: 1.70, 0.68, 0.37
> Tasks: 64 total, 4 running, 60 sleeping, 0 stopped, 0 zombie
> Cpu0 : 0.0%us,100.0%sy, 0.0%ni, 0.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st
> Cpu1 : 6.4%us, 87.2%sy, 0.0%ni, 5.8%id, 0.0%wa, 0.6%hi, 0.0%si, 0.0%st
> Mem: 895384k total, 283568k used, 611816k free, 35492k buffers
> Swap: 1959920k total, 0k used, 1959920k free, 163044k cached
>
> PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
> 4632 root 20 0 17216 800 580 S 104 0.1 0:34.22 syslog-ng
> 28505 root 20 0 205m 11m 4024 S 6 1.3 0:21.16 X
> 28518 root 20 0 56292 5652 4492 S 1 0.6 0:01.80 fluxbox
> 1 root 20 0 3724 608 508 S 0 0.1 0:00.36 init
>
> So far I have no clue why C1E-idle in conjunction with virtual wire
> mode causes this strange behaviour.
>
> ... and I start to think about the root cause of all this.
>
> I've performed similar tests under X with the IRQ0/INT0 configuration and
> I did not see above symptoms.
So lets fall back to the IRQ0/INT0 configuration on this box.
This basically restores the dont-use-the-lapic-timer exception mechanism
that was unconditional on this box prior commit 8750bf5 ("x86: add C1E
aware idle function").
Glauber Costa [Wed, 25 Jun 2008 15:48:47 +0000 (12:48 -0300)]
x86: merge __get_user_asm and its users.
Move __get_user_asm and __get_user_size and __get_user_nocheck
to uaccess.h. This requires us to define a macro at __get_user_size
for the 64-bit access case.
Signed-off-by: Glauber Costa <gcosta@redhat.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Glauber Costa [Wed, 25 Jun 2008 14:48:29 +0000 (11:48 -0300)]
x86: merge __put_user_asm and its user.
Move both __put_user_asm and __put_user_size to
uaccess.h. i386 already had a special function for 64-bit access,
so for x86_64, we just define a macro with the same name.
Note that for X86_64, CONFIG_X86_WP_WORKS_OK will always
be defined, so the #else part will never be even compiled in.
Signed-off-by: Glauber Costa <gcosta@redhat.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>