Jamie Lenehan [Wed, 6 Dec 2006 03:05:02 +0000 (12:05 +0900)]
sh: sh775x/titan fixes for irq header changes.
The following moves the creation of IPR interupts into setup-7750.c
and updates a few other things to make it all work after the "Drop
CPU subtype IRQ headers" commit. It boots and runs fine on my titan
board.
- adds an ipr_idx to the ipr_data and uses a function in the subtype
code to calculate the address of the IPR registers
- adds a function to enable individual interrupt mode for externals
in the subtype code and calls that from the titan board code
instead of doing it directly.
- I changed the shift in the ipr_data to be the actual # of bits to
shift, instead of the numnber / 4 - made it easier to match with
the manual.
Signed-off-by: Jamie Lenehan <lenehan@twibble.org> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Wed, 6 Dec 2006 02:20:53 +0000 (11:20 +0900)]
sh: Fixup pte_mkhuge() build failure.
When hugetlbpage support isn't enabled, this can be bogus.
Wrap it back in _PAGE_FLAGS_HARD to avoid changes to the
base PTE when not aiming for larger sizes.
Paul Mundt [Fri, 1 Dec 2006 05:32:54 +0000 (14:32 +0900)]
sh: Fixup movli.l/movco.l atomic ops for gcc4.
gcc4 gets a bit pissy about the outputs:
include/asm/atomic.h: In function 'atomic_add':
include/asm/atomic.h:37: error: invalid lvalue in asm statement
include/asm/atomic.h:30: error: invalid lvalue in asm output 1
...
this ended up being a thinko anyways, so just fix it up.
Verified for proper behaviour with the older toolchains, too.
Paul Mundt [Fri, 1 Dec 2006 04:23:47 +0000 (13:23 +0900)]
sh: dyntick infrastructure.
This adds basic NO_IDLE_HZ support to the SH timer API so timers
are able to wire it up. Taken from the ARM version, as it fit in
to our API with very few changes needed.
Paul Mundt [Fri, 1 Dec 2006 04:15:14 +0000 (13:15 +0900)]
sh: Clock framework tidying.
This syncs up the SH clock framework with the linux/clk.h API,
for which there were only some minor changes required, namely
the clk_get() dev_id and subsequent callsites.
Paul Mundt [Fri, 1 Dec 2006 04:12:05 +0000 (13:12 +0900)]
sh: Turn off IRQs around get_timer_offset() calls.
Since all of the sys_timer sources currently do this on their own
within the ->get_offset() path, it's more sensible to just have
the caller take care of it when grabbing xtime_lock. Incidentally,
this is more in line with what others (ie, ARM) are doing already.
Paul Mundt [Fri, 1 Dec 2006 03:14:11 +0000 (12:14 +0900)]
sh: Get the PGD right in oops case with 64-bit PTEs.
Previously this was using a static pgd shift in the reporting
code, simply flip this to PGDIR_SHIFT which does the right
thing depending on varying PTE magnitudes on the SH-X2 MMU.
While we're at it, and since it's been recently added, use
get_TTB() for fetching the TTB, rather than the open coded
instructions.
Paul Mundt [Fri, 1 Dec 2006 03:01:43 +0000 (12:01 +0900)]
sh: Fix store queue bitmap end.
The end of the store queue bitmap is miscalculated when searching
for a free range in sq_remap(), missing the PAGE_SHIFT shift that's
done in sq_api_init(). This runs in to workloads where we can scan
beyond the end of the bitmap.
Paul Mundt [Mon, 27 Nov 2006 03:10:23 +0000 (12:10 +0900)]
sh: More flexible + SH7780 earlyprintk SCIF support.
This makes the early printk support somewhat more flexible,
moving the port definition to a config option, and making the
port initialization configurable for sh-ipl+g users.
At the same time, this allows us to trivially wire up the
SH7780 SCIF0, so that's thrown in too more or less for free.
Paul Mundt [Mon, 27 Nov 2006 03:06:26 +0000 (12:06 +0900)]
sh: Fixup various PAGE_SIZE == 4096 assumptions.
There were a number of places that made evil PAGE_SIZE == 4k
assumptions that ended up breaking when trying to play with
8k and 64k page sizes, this fixes those up.
The most significant change is the way we load THREAD_SIZE,
previously this was done via:
mov #(THREAD_SIZE >> 8), reg
shll8 reg
to avoid a memory access and allow the immediate load. With
a 64k PAGE_SIZE, we're out of range for the immediate load
size without resorting to special instructions available in
later ISAs (movi20s and so on). The "workaround" for this is
to bump up the shift to 10 and insert a shll2, which gives a
bit more flexibility while still being much cheaper than a
memory access.
Paul Mundt [Fri, 24 Nov 2006 10:46:18 +0000 (19:46 +0900)]
sh: Fixup 4K irq stacks.
There was a clobber issue with the register we were saving
the stack in, so we switch to a register that we handle in
the clobber list properly already.
This also follows the x86 changes for allowing the softirq
checks from hardirq context.
Mark Glaisher [Fri, 24 Nov 2006 06:13:52 +0000 (15:13 +0900)]
sh: dma-api channel capability extensions.
This extends the SH DMA API for allowing handling of DMA
channels based off of their respective capabilities.
A couple of functions are added to the existing API,
the core bits are register_chan_caps() for registering
channel capabilities, and request_dma_bycap() for fetching
a channel dynamically based off of a capability set.
Signed-off-by: Mark Glaisher <mark.glaisher@st.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Fri, 24 Nov 2006 05:50:05 +0000 (14:50 +0900)]
sh: Drop name overload in dma-sh.
Pass along the dev_id from request_dma() all the way down,
rather than inserting an artificial name relating to the TEI
line that we were doing before.
This makes the line a bit less obvious, but dev_id is the proper
behaviour for this regardless.
Stuart Menefy [Fri, 24 Nov 2006 04:01:36 +0000 (13:01 +0900)]
sh: Fix syscall tracing ordering.
The implementation of system call tracing in the kernel has a
couple of ordering problems:
- the validity of the system call number is checked before
calling out to system call tracing code, and should be
done after
- the system call number used when tracing is the one the
system call was invoked with, while the system call tracing
code can legitimatly change the call number (for example
strace permutes fork into clone)
This patch fixes both of these problems, and also reoders the
code slightly to make the direct path through the code the
common case.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Fri, 24 Nov 2006 02:22:57 +0000 (11:22 +0900)]
sh: generic push-switch framework.
This adds support for a generic push switch framework. Adaptable for
various switches, including GPIO switches and the push switches commonly
found on Renesas debug boards.
This allows switch states to be trivially reported through sysfs.
Stuart Menefy [Tue, 21 Nov 2006 06:38:05 +0000 (15:38 +0900)]
sh: pmd rework.
Remove extra bits from the pmd structure and store a kernel logical
address rather than a physical address. This allows it to be directly
dereferenced. Another piece of wierdness inherited from x86.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Stuart Menefy [Tue, 21 Nov 2006 02:16:57 +0000 (11:16 +0900)]
sh: gcc4 support.
This fixes up the kernel for gcc4. The existing exception handlers
needed some wrapping for pt_regs access, acessing the registers
via a RELOC_HIDE() pointer.
The strcpy() issues popped up here too, so add -ffreestanding and
kill off the symbol export.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Tue, 21 Nov 2006 02:12:19 +0000 (11:12 +0900)]
sh: Explicit endian selection support.
Previously big endian was simply assumed if little endian was
not set, which led to some cflags ordering issues. There's not
much point to not having a big endian option, so shove one in
a choice and wire it up in the Makefile.
This lets us clean up some of the cflags ordering while we're
at it.
Paul Mundt [Mon, 20 Nov 2006 05:30:26 +0000 (14:30 +0900)]
sh: Preliminary support for SH-X2 MMU.
This adds some preliminary support for the SH-X2 MMU, used by
newer SH-4A parts (particularly SH7785).
This MMU implements a 'compat' mode with SH-X MMUs and an
'extended' mode for SH-X2 extended features. Extended features
include additional page sizes (8kB, 4MB, 64MB), as well as the
addition of page execute permissions.
The extended mode attributes are placed in a second data array,
which requires us to switch to 64-bit PTEs when in X2 mode.
With the addition of the exec perms, we also overhaul the mmap
prots somewhat, now that it's possible to handle them more
intelligently.
Paul Mundt [Mon, 20 Nov 2006 04:55:34 +0000 (13:55 +0900)]
sh: Drop CPU subtype IRQ headers.
This drops the various IRQ headers that were floating around
and primarily providing hardcoded IRQ definitions for the
various CPU subtypes. This quickly got to be an unmaintainable
mess, made even more evident by the subtle breakage introduced
by the SH-2 and SH-2A changes.
Now that subtypes are able to register IRQ maps directly, just
rip all of the headers out.
Matthew Wilcox [Mon, 4 Dec 2006 10:38:31 +0000 (03:38 -0700)]
[PATCH] Centralise definitions of sector_t and blkcnt_t
CONFIG_LBD and CONFIG_LSF are spread into asm/types.h for no particularly
good reason.
Centralising the definition in linux/types.h means that arch maintainers
don't need to bother adding it, as well as fixing the problem with
x86-64 users being asked to make a decision that has absolutely no
effect.
The H8/300 porters seem particularly confused since I'm not aware of any
microcontrollers that need to support 2TB filesystems.
Signed-off-by: Matthew Wilcox <matthew@wil.cx> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Al Viro [Mon, 4 Dec 2006 22:05:09 +0000 (22:05 +0000)]
[PATCH] remote memory corruptor in ibmtr.c
ip_summed changes last summer had missed that one. As the result,
we have ip_summed interpreted as CHECKSUM_PARTIAL now. IOW,
->csum is interpreted as offset of checksum in the packet. net/core/*
will both read and modify the value as that offset, with obvious
reasons. At the very least it's a remote memory corruptor.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/paulus/powerpc: (194 commits)
[POWERPC] Add missing EXPORTS for mpc52xx support
[POWERPC] Remove obsolete PPC_52xx and update CLASSIC32 comment
[POWERPC] ps3: add a default zImage target
[POWERPC] Add of_platform_bus support to mpc52xx psc uart driver
[POWERPC] typo fix and whitespace cleanup on mpc52xx-uart driver
[POWERPC] Fix debug printks for 32-bit resources in the PCI code
[POWERPC] Replace kmalloc+memset with kzalloc
[POWERPC] Linkstation / kurobox support
[POWERPC] Add the e300c3 core to the CPU table.
[POWERPC] ppc: m48t35 add missing bracket
[POWERPC] iSeries: don't build head_64.o unnecessarily
[POWERPC] iSeries: stop dt_mod.o being rebuilt unnecessarily
[POWERPC] Fix cputable.h for combined build
[POWERPC] Allow CONFIG_BOOTX_TEXT on iSeries
[POWERPC] Allow xmon to build on legacy iSeries
[POWERPC] Change ppc64_defconfig to use AUTOFS_V4 not V3
[POWERPC] Tell firmware we can handle POWER6 compatible mode
[POWERPC] Clean images in arch/powerpc/boot
[POWERPC] Fix OF pci flags parsing
[POWERPC] defconfig for lite5200 board
...
Grant Likely [Mon, 27 Nov 2006 21:21:02 +0000 (14:21 -0700)]
[POWERPC] Add of_platform_bus support to mpc52xx psc uart driver
Needed to support mpc52xx boards in arch/powerpc. This patch
retains the platform_bus support when compiling for arch/ppc,
but uses the of_platform bindings for arch/powerpc.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Sylvain Munaut <tnt@246tNt.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Grant Likely [Mon, 27 Nov 2006 21:21:01 +0000 (14:21 -0700)]
[POWERPC] typo fix and whitespace cleanup on mpc52xx-uart driver
Single typo fix and whitespace changes. In preparation for heavy
changes to this driver when support for arch/powerpc is added.
Since the driver will be changing significantly anyway, then may
as well take the opportunity to clean it up first.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Sylvain Munaut <tnt@246tNt.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Atsushi Nemoto [Sun, 3 Dec 2006 15:42:59 +0000 (00:42 +0900)]
[MIPS] Unify csum_partial.S
The 32-bit version and 64-bit version are almost equal. Unify them. This
makes further improvements (for example, copying with parallel, supporting
PREFETCH, etc.) easier.
Ralf Baechle [Thu, 30 Nov 2006 15:38:10 +0000 (15:38 +0000)]
[MIPS] Fix atomic.h build errors.
For the definition of atomic64_t atomic.h was relying on <asm/types.h>
having been included previously. Before changeset d89d8e0637a5e4e0a12e90c4bc934d0d4c335239 this was happening as a
side effect of including <linux/spinlock.h>.
Atsushi Nemoto [Tue, 7 Nov 2006 09:02:44 +0000 (18:02 +0900)]
[MIPS] Use SYSVIPC_COMPAT to fix various problems on N32
N32 SysV IPC system calls should use 32-bit compatible code.
arch/mips/kernel/linux32.c have similar compatible code for O32, but
ipc/compat.c seems more complete. We can use it for both N32 and O32.
This patch should fix these problems (and other possible problems):
Linus Torvalds [Mon, 4 Dec 2006 21:12:29 +0000 (13:12 -0800)]
Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: (82 commits)
[PATCH] pata_ali: small fixes
[PATCH] pata_via: VIA 8251 bridged systems are now out and about
[PATCH] trivial piix: swap bogus dot for comma space
[PATCH] sata_promise: PHYMODE4 fixup
[PATCH] libata: always use polling IDENTIFY
[libata] pata_cs5535: fix build
[PATCH] ahci: do not powerdown during initialization
[PATCH] libata: prepare ata_sg_clean() for invocation from EH
[PATCH] libata: separate out rw ATA taskfile building into ata_build_rw_tf()
[PATCH] libata: implement ata_exec_internal_sg()
[PATCH] libata: make sure IRQ is cleared after ata_bmdma_freeze()
[PATCH] libata: move BMDMA host status recording from EH to interrupt handler
[PATCH] libata: make sure sdev doesn't go away while rescanning
[PATCH] libata: don't request sense if the port is frozen
[PATCH] libata: fix READ CAPACITY simulation
[PATCH] libata: implement ATA_FLAG_SETXFER_POLLING and use it in pata_via, take #2
[PATCH] libata: set IRQF_SHARED for legacy PCI IDE IRQs
[PATCH] libata: remove unused HSM_ST_UNKNOWN
[PATCH] libata: kill unnecessary sht->max_sectors initializations
[PATCH] libata: add missing sht->slave_destroy
...
Alan [Mon, 4 Dec 2006 16:36:05 +0000 (16:36 +0000)]
[PATCH] pata_ali: small fixes
Switch to pci_get_bus_and_slot because some x86 systems seem to be
handing us a device with dev->bus = NULL. Also don't apply the isa fixup
to revision C6 and later of the chip.
Really we need to work out wtf is handing us pdev->bus = NULL, but firstly
and more importantly we need the drivers working.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[SUNHME]: Fix for sunhme failures on x86
[XFRM] xfrm_user: Better validation of user templates.
[DCCP] tfrc: Binary search for reverse TFRC lookup
[DCCP] ccid3: Deprecate TFRC_SMALLEST_P
[DCCP] tfrc: Identify TFRC table limits and simplify code
[DCCP] tfrc: Add protection against invalid parameters to TFRC routines
[DCCP] tfrc: Fix small error in reverse lookup of p for given f(p)
[DCCP] tfrc: Document boundaries and limits of the TFRC lookup table
[DCCP] ccid3: Fix warning message about illegal ACK
[DCCP] ccid3: Fix bug in calculation of send rate
[DCCP]: Fix BUG in retransmission delay calculation
[DCCP]: Use higher RTO default for CCID3
Linus Torvalds [Mon, 4 Dec 2006 16:29:45 +0000 (08:29 -0800)]
Merge branch 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6: (34 commits)
[S390] Don't use small stacks when lockdep is used.
[S390] cio: Use device_reprobe() instead of bus_rescan_devices().
[S390] cio: Retry internal operations after vary off.
[S390] cio: Use path verification for last path gone after vary off.
[S390] non-unique constant/macro identifiers.
[S390] Memory detection fixes.
[S390] cio: Make ccw_dev_id_is_equal() more robust.
[S390] Convert extmem spin_lock into a mutex.
[S390] set KBUILD_IMAGE.
[S390] lockdep: show held locks when showing a stackdump
[S390] Add dynamic size check for usercopy functions.
[S390] Use diag260 for memory size detection.
[S390] pfault code cleanup.
[S390] Cleanup memory_chunk array usage.
[S390] Misaligned wait PSW at memory detection.
[S390] cpu shutdown rework
[S390] cpcmd <-> __cpcmd calling issues
[S390] Bad kexec control page allocation.
[S390] Reset infrastructure for re-IPL.
[S390] Some documentation typos.
...
David Wu [Mon, 4 Dec 2006 07:27:22 +0000 (17:27 +1000)]
[PATCH] m68knommu: add SHM support
It turns out SHMAT, SHMDT, SHMGET and SHMCTL support in sys_ipc() for
m68knommu in 2.6 kernel(uClinux-dist-20060803 release) is missing.
(copied from m68k sources, report by David Wu <davidwu@arcturusnetworks.com>)
Adrian Bunk [Mon, 4 Dec 2006 07:26:44 +0000 (17:26 +1000)]
[PATCH] m68knommu: fix compile when CONFIG_BLK_DEV_INITRD=n
This patch fixes the following compile error with
CONFIG_BLK_DEV_INITRD=n and -Werror-implicit-function-declaration:
...
CC arch/m68knommu/kernel/setup.o
/home/bunk/linux/kernel-2.6/linux-2.6.18-rc5-mm1/arch/m68knommu/kernel/setup.c: In function 'setup_arch':
/home/bunk/linux/kernel-2.6/linux-2.6.18-rc5-mm1/arch/m68knommu/kernel/setup.c:268: error: implicit declaration of function 'paging_init'
make[2]: *** [arch/m68knommu/kernel/setup.o] Error 1
Heiko Carstens [Mon, 4 Dec 2006 14:41:10 +0000 (15:41 +0100)]
[S390] Don't use small stacks when lockdep is used.
The lock dependency validator adds a bunch of extra stack frames to
the stack, which can cause stack overflows. Especially seen on 31 bit
where the small stack is only 4k.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cornelia Huck [Mon, 4 Dec 2006 14:41:01 +0000 (15:41 +0100)]
[S390] cio: Use path verification for last path gone after vary off.
If the last path to a device is gone after a chpid has been varied
off, putting it on the slow queue doesn't prevent a device driver
from still attempting to use it (it may stay on the slow queue for a
long time). Instead, trigger a verify event which will prevent I/O
attempts from the device driver immediately.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Ursula Braun [Mon, 4 Dec 2006 14:40:59 +0000 (15:40 +0100)]
[S390] non-unique constant/macro identifiers.
Add some prefixes to constands defined in drivers/s390/net/qdio.h
and drivers/s390/lcs.h to make it possible to include the three
header files drivers/s390/net/qeth.h, drivers/s390/net/qdio.h and
drivers/net/s390/lcs.h in one C file. This is required for the
patch that generates the kerntypes.o file for use by lcrash.
Signed-off-by: Ursula Braun <braunu@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Mon, 4 Dec 2006 14:40:56 +0000 (15:40 +0100)]
[S390] Memory detection fixes.
VMALLOC_END on 31bit should be 0x8000000UL instead of 0x7fffffffL.
The page mask which is used to make sure memory_end is on 4MB/2MB
boundary is wrong and not needed. Therefore remove it.
Make sure a vmalloc area does also exist and work on (future)
machines with 4TB and more memory.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cornelia Huck [Mon, 4 Dec 2006 14:40:54 +0000 (15:40 +0100)]
[S390] cio: Make ccw_dev_id_is_equal() more robust.
Using memcmp to compare ccw_dev_id implies that the whole structure (incl.
padding) has always been completely initialized to sane values. Comparing
the structures field by field doesn't make such assumptions.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Mon, 4 Dec 2006 14:40:47 +0000 (15:40 +0100)]
[S390] lockdep: show held locks when showing a stackdump
Follow i386/x86_64:
lockdep can be used to print held locks when printing a
backtrace. This can be useful when debugging things like
'scheduling while atomic' asserts.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Gerald Schaefer [Mon, 4 Dec 2006 14:40:45 +0000 (15:40 +0100)]
[S390] Add dynamic size check for usercopy functions.
Use a wrapper for copy_to/from_user to chose the best usercopy method.
The mvcos instruction is better for sizes greater than 256 bytes, if
mvcos is not available a page table walk is better for sizes greater
than 1024 bytes. Also removed the redundant copy_to/from_user_std_small
functions.
Signed-off-by: Gerald Schaefer <geraldsc@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Mon, 4 Dec 2006 14:40:42 +0000 (15:40 +0100)]
[S390] Use diag260 for memory size detection.
Avoid the tprot loop if diag260 works and reports that there are no
holes in memory. The tprot instruction can lead to a significant delay
in the ipl process if the virtual guest has a lot of memory and the
host is under memory pressure.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Mon, 4 Dec 2006 14:40:36 +0000 (15:40 +0100)]
[S390] Misaligned wait PSW at memory detection.
If the memory detection code would ever reach the point where it would
load the wait psw, it would generate a specification exception and the
system would crash at ipl time. This is because of a misaligned wait
psw. It needs to be on a double word boundary instead of a word
boundary.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Mon, 4 Dec 2006 14:40:33 +0000 (15:40 +0100)]
[S390] cpu shutdown rework
Let one master cpu kill all other cpus instead of sending an external
interrupt to all other cpus so they can kill themselves.
Simplifies reipl/shutdown functions a lot.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Mon, 4 Dec 2006 14:40:30 +0000 (15:40 +0100)]
[S390] cpcmd <-> __cpcmd calling issues
In case of reipl cpcmd gets called when all other cpus are not running
anymore. To prevent deadlocks change __cpcmd so that it doesn't take
any locks and call cpcmd or __cpcmd, whatever is correct in the current
context.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Mon, 4 Dec 2006 14:40:28 +0000 (15:40 +0100)]
[S390] Bad kexec control page allocation.
KEXEC_CONTROL_MEMORY_LIMIT is an unsigned long value and therefore
should be defined as one. Otherwise the kexec control page can be
allocated above 2GB which will cause a specification exception on the
sam31 instruction in the s390 kexec relocation code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
projects / linux-2.6 / log