David Brownell [Fri, 23 Sep 2005 05:30:48 +0000 (22:30 -0700)]
[PATCH] one less word in struct device
This saves a word from "struct device" ... there's a refcounting mechanism
stub that's rather ineffective (the values are never even tested!), which
can safely be deleted. With this patch it uses normal device refcounting,
so any potential users of the pm_parent mechanism will be more correct.
(That mechanism is actually unusable for now though; it does nothing.)
Alan Stern [Fri, 16 Sep 2005 18:22:51 +0000 (14:22 -0400)]
[PATCH] USB: UHCI: Split apart the physical and logical framelist arrays
This patch (as563) splits the physical and logical framelist arrays in
uhci-hcd into two separate pieces. This will allow slightly better memory
utilization, since each piece is no larger than a single page whereas
before the whole thing was a little bigger than two pages. It also allows
the logical array to be allocated in non-DMA-coherent memory.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 16 Sep 2005 18:17:45 +0000 (14:17 -0400)]
[PATCH] USB: UHCI: Remove unused fields and unneeded tests for NULL
This patch (as562) removes from the uhci-hcd driver a few unused fields
and some unnecessary tests against NULL and assignments to NULL. In fact
it wasn't until fairly recently that the tests became unnecessary.
Before last winter it was possible that the driver's stop() routine would
get called even if the start() routine returned an error, but now that
can't happen. Hence there's no longer any need to check for partial
initialization.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 14 Sep 2005 02:59:11 +0000 (19:59 -0700)]
[PATCH] remove some USB_SUSPEND dependencies
This simplifies some of the PM-related #ifdeffing by recognizing
that USB_SUSPEND depends on PM. Also, OHCI drivers were often
testing for USB_SUSPEND when they should have tested just PM.
David Brownell [Wed, 14 Sep 2005 02:57:36 +0000 (19:57 -0700)]
[PATCH] remove duplicated resume path code
This gets rid of some inconsistently duplicated logic to resume interfaces.
Similar code was in both finish_port_resume() and in usb_generic_resume().
Now there is just one copy of that code, accessed regardless of whether
CONFIG_USB_SUSPEND is enabled. Fault handling is also more consistent.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 14 Sep 2005 02:57:27 +0000 (19:57 -0700)]
[PATCH] remove usb_suspend_device() parameter
This patch removes the extra usb_suspend_device() parameter. The original
reason to pass that parameter was so that this routine could suspend any
active children. A previous patch removed that functionality ... leaving
no reason to pass the parameter. A close analogy is pci_set_power_state,
which doesn't need a pm_message_t either.
On the internal code path that comes through the driver model, the parameter
is now used to distinguish cases where USB devices need to "freeze" but not
suspend. It also checks for an error case that's accessible through sysfs:
attempting to suspend a device before its interfaces (or for hubs, ports).
David Brownell [Wed, 14 Sep 2005 02:57:04 +0000 (19:57 -0700)]
[PATCH] remove suspend-path recursion
This patch removes some recursion in the CONFIG_USB_SUSPEND logic, which
suspended children (of devices or hubs) that weren't already suspended.
When it sees such cases, suspend now just fails cleanly.
That logic was not needed during system-wide sleep state transitions; and
given the current notions of how to manage selective suspend transitions,
we don't want it there either. Where it was particularly handy was coping
with various limitations of the sysfs "echo -n N > power/state" support.
(These include assuming that "N" is always meaningful to the driver; and
that drivers can only transition to state N from state zero.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 14 Sep 2005 02:56:33 +0000 (19:56 -0700)]
[PATCH] usb_interface power state
This updates the handling of power state for USB interfaces.
- Formalizes an existing invariant: interface "power state" is a boolean:
ON when I/O is allowed, and FREEZE otherwise. It does so by defining
some inlined helpers, then using them.
- Adds a useful invariant: the only interfaces marked active are those
bound to non-suspended drivers. Later patches build on this invariant.
- Simplifies the interface driver API (and removes some error paths) by
removing the requirement that they record power state changes during
suspend and resume callbacks. Now usbcore does that.
A few drivers were simplified to address that last change.
Pete Zaitcev [Sat, 24 Sep 2005 20:10:16 +0000 (13:10 -0700)]
[PATCH] ub: suppress gcc warnings for pointer casts
When building on a 64-bit platform, gcc produces a warning
"cast of a pointer to an integer of a different size".
The scatterlist.offset on the LHS is unsigned int, so I used
that originally.
This patch adds endpoint information for both devices and interfaces to
sysfs. Previously it was only possible to get the endpoint information
from usbfs, and never possible to get any information on endpoint 0.
[PATCH] USB: ftdi: Artemis and ATIK based USB astronomical CCD cameras
This patch enables direct kernel support for the Artemis
and ATIK astronomical based USB CCD cameras.
Since all communications with this camera are done via an
FTDI 245BM chip, it was only needed to specify the
ProductID and VendorID of all three devices.
In what tests are concerned, data was transfered from and
to the FTDI at the chips Top speed (360KB/s).
Jesse Barnes [Tue, 25 Oct 2005 17:28:42 +0000 (10:28 -0700)]
[PATCH] PCI fixup for Toshiba laptops and ohci1394
This is a fix for a bug I see on my Toshiba laptop, where the ohci1394
controller gets initialized improperly. The patch adds two PCI fixups
to arch/i386/pci/fixup.c, one that happens early on to cache the value
of the PCI_CACHE_LINE_SIZE config register, and another that later
restores the value, along with a valid IRQ number and some BAR values.
I've tested it on my laptop, and it prevents me from running into what I
consider to be a major bug: IRQ 11 is disabled by the IRQ debug code,
causing my wireless to break.
Thanks to Rob for the original patch to ohci1394.c and Stefan for lots
of proofreading (and a last minute bug caught in review!) and additional
information collection. I think the DMI system list is correct, but we
may need to add some more PCI IDs to the PCI_FIXUP macros over time.
Reduce the number of debug messages generated if shpchp debug is
enabled. I tried to restrict this to removing debug messages that
are either early-driver-debug type messages, or print information
that can be inferred through other debug prints.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
State information is currently stored in per-slot as well as
per-pci-function data structures in shpchp. There's a lot of
overlap in the information kept, and some of it is never used.
This patch consolidates the state information to per-slot and
eliminates unused data structures. The biggest change is to
eliminate the pci_func structure and the code around managing
its lists.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[PATCH] shpchp: dont save PCI config for hotplug slots/devices
This patch eliminates saving the PCI config header for devices
in hotplug capable slots. We now use the PCI core to get the
specific parts of the config header as required.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[PATCH] shpchp: detect SHPC capability before doing a lot of work
The shpc driver registers its probe function for all pci-pci
bridges in the system. Not all of them will be shpc capable, so
look for this capability early in the probe function and return
if there's no work to do on this bridge. The old shpc driver
did some initialization work on all bridges before detecting
that shpc is not supported and unwinds the work it's already done
in that case.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reduce the SHPC hotplug driver's dependence on ACPI. We don't
walk the acpi namespace anymore to build a list of bridges and
devices. The remaining interaction with ACPI is to run the
_OSHP method to transition control of hotplug hardware from
system BIOS to the shpc hotplug driver, and to run the _HPP
method to get hotplug device parameters like cache line size,
latency timer and SERR/PERR enable from BIOS.
Note that one of the side effects of this patch is that shpchp
does not enable the hot-added device or its DMA bus mastering
automatically now. It expects the device driver to do that.
This may break some drivers and we will have to fix them as
they are reported.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[PATCH] shpchp: remove redundant display of PCI device resources
Info about resources assigned to PCI devices is already available
through sysfs and pci utilities. There's no need for shpchp to
create another sysfs file to display the same information.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[PATCH] shpchp: use the PCI core for hotplug resource management
This patch converts the standard hotplug controller driver to use
the PCI core for resource management. This eliminates a whole lot
of duplicated code, and integrates shpchp in the system's normal
PCI handling code.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[PATCH] ppc64 PCI Hotplug: cleanup unsymmetric API routines
This is a minor patch to the ppc64 PCI hotplug code; it makes the call to
rpaphp_unconfig_pci_adapter() symmetric with respect to the call to
rpaphp_config_pci_adapter(). I discussed this with John Rose, who
had provided the last round of changes for these functions; he
appearently had this patch but somehow failed to mail it out.
Grant Coady [Thu, 29 Sep 2005 00:39:46 +0000 (10:39 +1000)]
[PATCH] pci_ids: remove duplicates from pci_ids.h
pci_ids.h cleanup: remove duplicated entries and change some defines to
explicit value rather than in terms of another constant, preparation for
removing unused symbols
Add pci_{enable,disable}_device() calls. Without pci_enable_device(),
dev->irq is garbage, and cpqphp relies on it.
This fixes a problem reported by Bruno Redondi. He reported a flood
of ACPI interrupts, that caused kacpid to run 100% of the time:
http://bugzilla.kernel.org/show_bug.cgi?id=5312
Cleanup the need_restore switch statement in
pci_set_power_state(). This makes it more safe by explicitly handling
all the PCI power states instead of handling them as the default
case. It also reads a little better IMHO.
Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Brian King [Tue, 27 Sep 2005 08:21:56 +0000 (01:21 -0700)]
[PATCH] PCI: ipr: Block config access during BIST
IPR scsi adapter have an exposure today in that they issue BIST to the adapter
to reset the card. If, during the time it takes to complete BIST, userspace
attempts to access PCI config space, the host bus bridge will master abort the
access since the ipr adapter does not respond on the PCI bus for a brief
period of time when running BIST. On PPC64 hardware, this master abort
results in the host PCI bridge isolating that PCI device from the rest of the
system, making the device unusable until Linux is rebooted. This patch makes
use of some newly added PCI layer APIs that allow for protection from
userspace accessing config space of a device in scenarios such as this.
Signed-off-by: Brian King <brking@us.ibm.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: James Bottomley <James.Bottomley@steeleye.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/scsi/ipr.c | 2 ++
1 file changed, 2 insertions(+)
Brian King [Tue, 27 Sep 2005 08:21:55 +0000 (01:21 -0700)]
[PATCH] PCI: Block config access during BIST
Some PCI adapters (eg. ipr scsi adapters) have an exposure today in that they
issue BIST to the adapter to reset the card. If, during the time it takes to
complete BIST, userspace attempts to access PCI config space, the host bus
bridge will master abort the access since the ipr adapter does not respond on
the PCI bus for a brief period of time when running BIST. On PPC64 hardware,
this master abort results in the host PCI bridge isolating that PCI device
from the rest of the system, making the device unusable until Linux is
rebooted. This patch is an attempt to close that exposure by introducing some
blocking code in the PCI code. When blocked, writes will be humored and reads
will return the cached value. Ben Herrenschmidt has also mentioned that he
plans to use this in PPC power management.
Jean Delvare [Wed, 26 Oct 2005 19:39:40 +0000 (21:39 +0200)]
[PATCH] hwmon: Add PEC support to the lm90 driver
Add PEC support to the lm90 driver. Only the ADM1032 chip supports it,
and in a rather tricky way, which is why this patch comes with
documentation reinforcements. At least, this demonstrates that the new
PEC support logic in i2c-core can properly deal with chips with partial
PEC support.
As enabling PEC causes a significant performance drop, it can be
disabled through a sysfs file (unsurprisingly named "pec").
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Wed, 26 Oct 2005 19:37:52 +0000 (21:37 +0200)]
[PATCH] hwmon: Separate the lm90 register read function
Preparatory patch to add PEC support to the lm90 driver. We need a
centralized function to read register values, where the PEC code will
be later inserted. A positive side effect is that read errors are now
handled properly.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Wed, 26 Oct 2005 19:28:55 +0000 (21:28 +0200)]
[PATCH] i2c: SMBus PEC support rewrite, 2 of 3
This is my rewrite of the SMBus PEC support. The original
implementation was known to have bugs (credits go to Hideki Iwamoto
for reporting many of them recently), and was incomplete due to a
conceptual limitation.
The rewrite affects only software PEC. Hardware PEC needs very little
code and is mostly untouched.
Technically, both implementations differ in that the original one
was emulating PEC in software by modifying the contents of an
i2c_smbus_data union (changing the transaction to a different type),
while the new one works one level lower, on i2c_msg structures (working
on message contents). Due to the definition of the i2c_smbus_data union,
not all SMBus transactions could be handled (at least not without
changing the definition of this union, which would break user-space
compatibility), and those which could had to be implemented
individually. At the opposite, adding PEC to an i2c_msg structure
can be done on any SMBus transaction with common code.
Advantages of the new implementation:
* It's about twice as small (from ~136 lines before to ~70 now, only
counting i2c-core, including blank and comment lines). The memory
used by i2c-core is down by ~640 bytes (~3.5%).
* Easier to validate, less tricky code. The code being common to all
transactions by design, the risk that a bug can stay uncovered is
lower.
* All SMBus transactions have PEC support in I2C emulation mode
(providing the non-PEC transaction is also implemented). Transactions
which have no emulation code right now will get PEC support for free
when they finally get implemented.
* Allows for code simplifications in header files and bus drivers
(patch follows).
Drawbacks (I guess there had to be at least one):
* PEC emulation for non-PEC capable non-I2C SMBus masters was dropped.
It was based on SMBus tricks and doesn't quite fit in the new design.
I don't think it's really a problem, as the benefit was certainly
not worth the additional complexity, but it's only fair that I at
least mention it.
Lastly, let's note that the new implementation does slightly affect
compatibility (both in kernel and user-space), but doesn't actually
break it. Some defines will be dropped, but the code can always be
changed in a way that will work with both the old and the new
implementations. It shouldn't be a problem as there doesn't seem to be
many users of SMBus PEC to date anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Wed, 26 Oct 2005 19:25:04 +0000 (21:25 +0200)]
[PATCH] i2c: SMBus PEC support rewrite, 1 of 3
Discard I2C_FUNC_SMBUS_*_PEC defines. i2c clients are not supposed to
check for PEC support of i2c bus drivers on individual SMBus
transactions, and i2c bus drivers are not supposed to advertise them.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Wed, 26 Oct 2005 19:20:17 +0000 (21:20 +0200)]
[PATCH] i2c: Drop unused parport i2c IDs
Drop unused i2c-over-parallel-port i2c IDs:
* I2C_HW_B_LPC was never actually used as far as I could search.
* I2C_HW_B_ELV and I2C_HW_B_VELLE are no more used since the
introduction of the unified i2c-parport driver in Linux 2.6.2.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mark M. Hoffman [Mon, 17 Oct 2005 21:01:45 +0000 (23:01 +0200)]
[PATCH] hwmon: New device ID for the smsc47b397 driver
This patch adds a new ID to the SMSC LPC47B397-NC hardware
monitoring driver - for a chip that is claimed to be 100%
compatible otherwise.
Signed-off-by: Bryan Young (Utilitek Systems, Inc.) Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stig Telfer [Fri, 7 Oct 2005 22:23:27 +0000 (00:23 +0200)]
[PATCH] i2c: Big i2c-elektor cleanup
Cleanups to the i2c-elektor driver:
* Set the i2c_adapter name field to "i2c-elektor" and use this string
in all resource requests and printks.
* Change space-padding for tab indentation, kill trailing white space,
remove space before comma.
* Use dev_info, pr_info and pr_debug instead of printk.
* Lines chopped to 80 columns.
Stig Telfer [Fri, 7 Oct 2005 22:21:48 +0000 (00:21 +0200)]
[PATCH] i2c: Fix i2c-elektor on Alpha
This patch updates the i2c-elektor driver, enabling it to compile
cleanly, load and run. The key change is that it uses the new
__iomem/iowrite8/ioread8 functions to abstract the direct or
memory-mapped variants of register access. Also, the original driver
would crash on module load on the Alpha because the PCI memory region
was not remapped into kernel memory.
I have managed the following testing:
* compiled and tested it on my Alpha UP2000+ system.
* compiles cleanly for x86 but I don't have the hardware to test.
Jean Delvare [Fri, 7 Oct 2005 22:19:52 +0000 (00:19 +0200)]
[PATCH] i2c: Drop meaningless use of I2C_DF_NOTIFY in i2c_client structures
I2C_DF_NOTIFY is an i2c_driver flag, using it as an i2c_client flag
doesn't make any sense.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Mark A. Greer <mgreer@mvista.com> Acked-by: Randy Vinson <rvinson@mvista.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Fri, 7 Oct 2005 22:17:35 +0000 (00:17 +0200)]
[PATCH] i2c: Rename i2c-parport variable to avoid confusion
It's a bit confusing to name a variable the same as an unrelated
structure. The compiler doesn't complain, but it certainly makes the
code harder to understand, and could confuse grep and LXR among
others.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Fri, 7 Oct 2005 22:15:59 +0000 (00:15 +0200)]
[PATCH] i2c: Drop I2C_SMBUS_I2C_BLOCK_MAX
Drop I2C_SMBUS_I2C_BLOCK_MAX, use I2C_SMBUS_BLOCK_MAX instead.
I2C_SMBUS_I2C_BLOCK_MAX has always been defined to the same value as
I2C_SMBUS_BLOCK_MAX, and this will never change: setting it to a lower
value would make no sense, setting it to a higher value would break
i2c_smbus_data compatibility. There is no point in changing
i2c_smbus_data to support larger block transactions in SMBus mode, as
no SMBus hardware supports more than 32 byte blocks. Thus, for larger
transactions, direct I2C transfers are the way to go.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Fri, 7 Oct 2005 22:12:01 +0000 (00:12 +0200)]
[PATCH] hwmon: Drop useless w83627hf initialization step
Drop a useless initialization step in the w83627hf driver. The comment
says that the W83627HF PWM2 can be disabled, but it can't. I suppose
this is a leftover from the w83781d driver (from which the w83627hf
driver is derived), as for example the W83782D had the ability to
disable PWM2.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Fri, 7 Oct 2005 22:10:00 +0000 (00:10 +0200)]
[PATCH] hwmon: Drop legacy ISA address support from it87
Drop legacy ISA address support from the it87 driver. All supported
chips are Super-I/O chips, so the device ISA address can be safely read
from Super-I/O space rather than blindly assumed.
Two nearby inaccurate documentation statements have been fixed as well:
* The IT8705F doesn't have an SMBus interface.
* The SiS950 doesn't have a distinct prefix.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Fri, 7 Oct 2005 22:06:09 +0000 (00:06 +0200)]
[PATCH] i2c: Drop out-of-date, colliding ioctl definitions
Delete 2 out-of-date, colliding ioctl defines. I2C_UDELAY and
I2C_MDELAY are supposed to be used by i2c-algo-bit, but actually
aren't (and I suspect never were). Moreover, their values are the same
as I2C_FUNCS and I2C_SLAVE_FORCE, respectively, which *are* widely
used.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Fri, 7 Oct 2005 22:00:31 +0000 (00:00 +0200)]
[PATCH] i2c: Documentation fixes
i2c documentation fixes.
>From Hideki Iwamoto:
* i2c_smbus_read_i2c_block_data is not deleted in 2.6.10. It still
exists.
* The name which can be set to i2c_driver is up to 31 characters.
>From Jean Delvare:
* Reword the paragraph about i2c_driver.name, to reflect the "new"
naming policy.
* Delete the out-of-date note about now gone inc_use and dec_use
fields.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Fri, 7 Oct 2005 21:56:46 +0000 (23:56 +0200)]
[PATCH] i2c: Cleanup i2c-i801 ifdefs
No more need to check for PEC support being available now that both
the i2c-core and the i2c-i801 drivers are part of the Linux kernel
source tree. It's just there.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Petr Vandrovec [Fri, 7 Oct 2005 21:11:03 +0000 (23:11 +0200)]
[PATCH] hwmon: Fix w83627ehf/hf vs PNPACPI conflict (bug #4014)
This patch changes w83627hf and w83627ehf drivers to reserve only ports
0x295-0x296, instead of full 0x290-0x297 range. While some other
sensors chips respond to all addresses in 0x290-0x297 range, Winbond
chips respond to 0x295-0x296 only (this behavior is implied by
documentation, and matches behavior observed on real systems). This is
not problem alone, as no BIOS was found to put something at these unused
addresses, and sensors chip itself provides nothing there as well.
But in addition to only respond to these two addresses, also BIOS
vendors report in their ACPI-PnP structures that there is some resource
at I/O address 0x295 of length 2. And when later this hwmon driver
attempts to request region with base 0x290/length 8, it fails as one
request_region cannot span more than one device.
Due to this we have to ask only for region this hardware really
occupies, otherwise driver cannot be loaded on systems with ACPI-PnP
enabled.
Signed-off-by: Petr Vandrovec <vandrove@vc.cvut.cz> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Fri, 7 Oct 2005 21:06:27 +0000 (23:06 +0200)]
[PATCH] i2c: Cleanup i2c-dev ioctl debug message
Cleanup the ioctl debug message in i2c-dev. In particular, the minor
number is redundant now that the minor number and the adapter number
are kept in sync.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / linux-2.6 / log