Till Harbaum [Tue, 1 May 2007 21:26:35 +0000 (23:26 +0200)]
i2c: New i2c-tiny-usb bus driver
Add a driver for the i2c-tiny-usb interface. This is a simple
do-it-yourself USB to I2C interface targeted at experimental and
home use. See the i2c-tiny-usb homepage for hardware details:
http://www.harbaum.org/till/i2c_tiny_usb
Signed-off-by: Till Harbaum <till@harbaum.org> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jean Delvare [Tue, 1 May 2007 21:26:35 +0000 (23:26 +0200)]
i2c: Documentation update
Make the documentation on how to write and port i2c drivers more in
line with the current state of things:
* i2c-isa is deprecated and soon gone, so stop advertising it.
* Drop many sensors-specific references. Most of them were outdated
anyway.
* Update the example code to reflect the recent and not-so-recent
API and coding style preference changes.
* Simplify the example init and cleanup functions.
This should make things less complex to understand for newcomers.
This is a very simple bitbanging I2C bus driver utilizing the new
arch-neutral GPIO API. Useful for chips that don't have a built-in
I2C controller, additional I2C busses, or testing purposes.
To use, include something similar to the following in the
board-specific setup code:
Register this platform_device, set up the I2C pins as GPIO if
required and you're ready to go. This will use default values for
udelay and timeout, and will work with GPIO hardware that does not
support open drain mode, but allows sensing of the SDA and SCL lines
even when they are being driven.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jean Delvare [Tue, 1 May 2007 21:26:33 +0000 (23:26 +0200)]
i2c-pxa: Clean transaction stop
It was reported to me that the i2c-pxa driver was not able to process
more that 50 transactions per second. Investigation revealed that the
I2C unit was busy for 20 ms after every transaction. The reason seems
to be that we forget to clear the STOP and ACKNACK bits at the end of
the transaction. According to the PXA27x developer's manual, we shall
do so.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Lennert Buytenhek <kernel@wantstofly.org> Cc: Nicolas Pitre <nico@cam.org>
Jean Delvare [Tue, 1 May 2007 21:26:33 +0000 (23:26 +0200)]
i2c-algo-bit: Improve debugging
Improve the debugging features of the i2c-algo-bit driver:
* Make it possible to compile the driver without debugging support
at all, making it much smaller.
* Use dev_dbg() for debugging messages where possible, and dev_err()
for error messages.
* Remove redundant debugging messages.
These changes allowed for minor code cleanups, which are included
as well.
Jean Delvare [Tue, 1 May 2007 21:26:33 +0000 (23:26 +0200)]
i2c-algo-bit: Implement a 50/50 SCL duty cycle
The original i2c-algo-bit implementation uses a 33/66 SCL duty cycle
when bits are being written on the bus. While the I2C specification
doesn't forbid it, this prevents us from driving the I2C bus to its
max speed, limiting us to 66 kbps max on standard I2C busses.
Implementing a 50/50 duty cycle instead lets us max out the bandwidth
up to the theoretical max of 100 kbps on standard I2C busses. This is
particularly important when large amounts of data need to be transfered
over the bus, as is the case with some TV adapters when the firmware is
being uploaded.
In fact this change even allows, at least in theory, fast-mode I2C
support at 125, 166 and 250 kbps. There's no way to reach the
theoretical max of 400 kbps with this implementation. But I don't
think we want to put efforts in that direction anyway: software-driven
I2C is very CPU-intensive and bad for latency.
Other timing changes:
* Don't set SDA high explicitly on error, we're going to issue a stop
condition before we leave anyway.
* If an error occurs when sending the slave address, yield the CPU
before retrying, and remove the additional delay after the new start
condition.
Jean Delvare [Tue, 1 May 2007 21:26:32 +0000 (23:26 +0200)]
i2c: Make i2c_del_driver a void function
Make i2c_del_driver a void function, like all other driver removal
functions. It always returned 0 even when errors occured, and nobody
ever actually checked the return value anyway. And we cannot fail
a module removal anyway.
Jean Delvare [Tue, 1 May 2007 21:26:32 +0000 (23:26 +0200)]
i2c: Move i2c-isa-only exported symbol declarations
Move the declaration of i2c-isa-only exported symbols to i2c-isa
itself, that's the best way to ensure nobody will attempt to use them.
Hopefully we'll get rid of the exports themselves soon anyway.
Jean Delvare [Tue, 1 May 2007 21:26:31 +0000 (23:26 +0200)]
i2c: Add i2c_new_probed_device()
Add a new helper function to instantiate an i2c device. It is meant as a
replacement for i2c_new_device() when you don't know for sure at which
address your I2C/SMBus device lives. This happens frequently on TV
adapters for example, you know there is a tuner chip on the bus, but
depending on the exact board model and revision, it can live at different
addresses. So, the new i2c_new_probed_device() function will probe the bus
according to a list of addresses, and as soon as one of these addresses
responds, it will call i2c_new_device() on that one address.
This function will make it possible to port the old i2c drivers to the
new model quickly.
Jean Delvare [Tue, 1 May 2007 21:26:31 +0000 (23:26 +0200)]
i2c-algo-bit: Add i2c_bit_add_numbered_bus
Add i2c_bit_add_numbered_bus(), which is equivalent to i2c_bit_add_bus
except that it calls i2c_add_numbered_adapter() at the end instead of
i2c_add_adapter().
David Brownell [Tue, 1 May 2007 21:26:31 +0000 (23:26 +0200)]
i2c: Add i2c_add_numbered_adapter()
This adds a call, i2c_add_numbered_adapter(), registering an I2C adapter
with a specific bus number and then creating I2C device nodes for any
pre-declared devices on that bus. It builds on previous patches adding
I2C probe() and remove() support, and that pre-declaration of devices.
This completes the core support for "new style" I2C device drivers.
Those follow the standard driver model for binding devices to drivers
(using probe and remove methods) rather than a legacy model (where the
driver tries to autoconfigure each bus, and registers devices itself).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Jean Delvare <khali@linux-fr.org>
David Brownell [Tue, 1 May 2007 21:26:31 +0000 (23:26 +0200)]
i2c: Add i2c_board_info and i2c_new_device()
This provides partial support for new-style I2C driver binding. It builds
on "struct i2c_board_info" declarations that identify I2C devices on a given
board. This is needed on systems with I2C devices that can't be fully probed
and/or autoconfigured, such as many embedded Linux configurations where the
way a given I2C device is wired may affect how it must be used.
There are two models for declaring such devices:
* LATE -- using a public function i2c_new_device(). This lets modules
declare I2C devices found *AFTER* a given I2C adapter becomes available.
For example, a PCI card could create adapters giving access to utility
chips on that card, and this would be used to associate those chips with
those adapters.
* EARLY -- from arch_initcall() level code, using a non-exported function
i2c_register_board_info(). This copies the declarations *BEFORE* such
an i2c_adapter becomes available, arranging that i2c_new_device() will
be called later when i2c-core registers the relevant i2c_adapter.
For example, arch/.../.../board-*.c files would declare the I2C devices
along with their platform data, and I2C devices would behave much like
PNPACPI devices. (That is, both enumerate from board-specific tables.)
To match the exported i2c_new_device(), the previously-private function
i2c_unregister_device() is now exported.
Pending later patches using these new APIs, this is effectively a NOP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Jean Delvare <khali@linux-fr.org>
David Brownell [Tue, 1 May 2007 21:26:30 +0000 (23:26 +0200)]
i2c: i2c stack can probe()
One of a series of I2C infrastructure updates to support enumeration using
the standard Linux driver model.
This patch updates probe() and associated hotplug/coldplug support, but
not remove(). Nothing yet _uses_ it to create I2C devices, so those
hotplug/coldplug mechanisms will be the only externally visible change.
This patch will be an overall NOP since the I2C stack doesn't yet create
clients/devices except as part of binding them to legacy drivers.
Some code is moved earlier in the source code, helping group more of the
per-device infrastructure in one place and simplifying handling per-device
attributes.
Terminology being adopted: "legacy drivers" create devices (i2c_client)
themselves, while "new style" ones follow the driver model (the i2c_client
is handed to the probe routine). It's an either/or thing; the two models
don't mix, and drivers that try mixing them won't even be registered.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jean Delvare [Tue, 1 May 2007 21:26:30 +0000 (23:26 +0200)]
i2c-pca-isa: Port to the new device driver model
Port the i2c-pca-isa driver to the new device driver model. I'm
using Rene Herman's new isa bus type, as it fits the needs nicely. One
benefit is that we can now give a proper parent to our i2c adapter.
Jean Delvare [Tue, 1 May 2007 21:26:30 +0000 (23:26 +0200)]
i2c-elektor: Port to the new device driver model
Port the i2c-elektor driver to the new device driver model. I'm
using Rene Herman's new isa bus type, as it fits the needs nicely. One
benefit is that we can now give a proper parent to our i2c adapter.
Jean Delvare [Tue, 1 May 2007 21:26:30 +0000 (23:26 +0200)]
scx200_acb: Fix PCI device reference count
The scx200_acb driver supports two kind of devices, PCI ones and ISA
ones. Even ISA ones are detected using the presence of a given PCI
device, and we get a reference to it, but never put it back, so we
have a leak. Fix it.
Jean Delvare [Tue, 1 May 2007 21:26:29 +0000 (23:26 +0200)]
i2c-parport: Optimize binary size
Initialize the fields of the i2c_adapter structure individually,
rather than copying a whole static template structure. This shaves
off 474 bytes or 14% (on i386) from the binary size.
Jean Delvare [Tue, 1 May 2007 21:26:29 +0000 (23:26 +0200)]
i2c-algo-bit: Emulate SMBus block read
Now that i2c-core lets the i2c bus drivers emulate the SMBus block read
and SMBus block process call transaction types, let's implement that in
the popular i2c bit-banging driver. This will also act as a reference
implementation for other bus drivers which want to do the same.
Jean Delvare [Tue, 1 May 2007 21:26:29 +0000 (23:26 +0200)]
i2c: Emulate SMBus block read over I2C
Let the I2C bus drivers emulate the SMBus Block Read and Block Process
Call transactions if they wish. This requires to define a new message
flag, which i2c-core will use to let the underlying I2C bus driver
know that the first received byte will specify the length of the read
message.
Jean Delvare [Tue, 1 May 2007 21:26:28 +0000 (23:26 +0200)]
i2c-algo-bit: Always send a stop condition before leaving
The i2c-algo-bit driver doesn't behave well on read errors: it'll
bail out without even sending a stop condition on the bus, so the bus
will be stuck. So make sure that we always send a stop condition on
the bus before we leave. The best way to make sure is to always send
it at the end of function bit_xfer.
David Brownell [Tue, 1 May 2007 21:26:28 +0000 (23:26 +0200)]
i2c: Rename dev_to_i2c_adapter()
Rename dev_to_i2c_adapter() as to_i2c_adapter(), since the previous
syntax was a surprising and needless difference from normal naming
conventions in Linux.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Jean Delvare <khali@linux-fr.org>
David Brownell [Tue, 1 May 2007 21:26:28 +0000 (23:26 +0200)]
i2c: Shrink struct i2c_client
This shrinks the size of "struct i2c_client" by 40 bytes:
- Substantially shrinks the string used to identify the chip type
- The "flags" don't need to be so big
- Removes some internal padding
It also adds kerneldoc for that struct, explaining how "name" is really a
chip type identifier; it's otherwise potentially confusing.
Because the I2C_NAME_SIZE symbol was abused for both i2c_client.name
and for i2c_adapter.name, this needed to affect i2c_adapter too. The
adapters which used that symbol now use the more-obviously-correct
idiom of taking the size of that field.
JD: Shorten i2c_adapter.name from 50 to 48 bytes while we're here, to
avoid wasting space in padding.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jean Delvare [Tue, 1 May 2007 21:26:28 +0000 (23:26 +0200)]
i2c: i2c_adapter devices need no driver
Kill i2c_adapter_driver as it doesn't make sense and it prevents
further i2c-core cleanups. i2c_adapter devices are virtual devices
(ex-class devices) and as such they don't need a driver.
Jean Delvare [Tue, 1 May 2007 21:26:27 +0000 (23:26 +0200)]
i2c: Kill i2c_adapter.class_dev
Kill i2c_adapter.class_dev. Instead, set the class of i2c_adapter.dev
to i2c_adapter_class, so that a symlink will be created for every
i2c_adapter in /sys/class/i2c-adapter.
The same change must be mirrored to i2c-isa as it duplicates some
of the i2c-core functionalities.
User-space tools and libraries might need some adjustments. In
particular, libsensors from lm_sensors 2.10.3 or later is required for
proper discovery of i2c adapter names after this change.
Linus Torvalds [Tue, 1 May 2007 00:43:48 +0000 (17:43 -0700)]
libata: honour host controllers that want just one host
The Marvell IDE interface on my machine would hit a BUG_ON() in
lib/iomem.c because it was calling ata_pci_init_one() specifying just a
single port on the host, but that would actually end up trying to
initialize two ports, the second one with bogus information.
This fixes "ata_pci_init_one()" so that it actually passes down the
n_ports variable that it got from the low-level driver to the host
allocation routine ("ata_host_alloc_pinfo()"), which results in the ATA
layer actually having the correct port number information.
And in order to make it all work, I also needed to fix a few places that
had incorrectly hard-coded the fact that a host always had exactly two
ports (both ata_pci_init_bmdma() and ata_request_legacy_irqs() would
just always iterate over both ports).
Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Berg [Mon, 30 Apr 2007 22:09:55 +0000 (15:09 -0700)]
power management: force pm_ops.valid callback to be assigned
This patch changes the docs and behaviour from "all states valid" to "no
states valid" if no .valid callback is assigned. Users of pm_ops that only
need mem sleep can assign pm_valid_only_mem without any overhead, others
will require more elaborate callbacks.
Now that all users of pm_ops have a .valid callback this is a safe thing to
do and prevents things from getting messy again as they were before.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Pavel Machek <pavel@ucw.cz> Looks-okay-to: Rafael J. Wysocki <rjw@sisk.pl> Cc: <linux-pm@lists.linux-foundation.org> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Berg [Mon, 30 Apr 2007 22:09:54 +0000 (15:09 -0700)]
power management: implement pm_ops.valid for everybody
Almost all users of pm_ops only support mem sleep, don't check in .valid and
don't reject any others in .prepare so users can be confused if they check
/sys/power/state, especially when new states are added (these would then
result in s-t-r although they're supposed to be something different).
This patch implements a generic pm_valid_only_mem function that is then
exported for users and puts it to use in almost all existing pm_ops.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: David Brownell <david-b@pacbell.net> Acked-by: Pavel Machek <pavel@ucw.cz> Cc: linux-pm@lists.linux-foundation.org Cc: Len Brown <lenb@kernel.org> Acked-by: Russell King <rmk@arm.linux.org.uk> Cc: Greg KH <greg@kroah.com> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Cc: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Berg [Mon, 30 Apr 2007 22:09:53 +0000 (15:09 -0700)]
power management: remove firmware disk mode
This patch removes the firmware disk suspend mode which is the wrong approach,
it is supposed to be used for implementing firmware-based disk suspend but
cannot actually be used for that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Pavel Machek <pavel@ucw.cz> Cc: <linux-pm@lists.linux-foundation.org> Cc: David Brownell <david-b@pacbell.net> Cc: Len Brown <lenb@kernel.org> Acked-by: Russell King <rmk@arm.linux.org.uk> Cc: Greg KH <greg@kroah.com> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Cc: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Berg [Mon, 30 Apr 2007 22:09:51 +0000 (15:09 -0700)]
rework pm_ops pm_disk_mode, kill misuse
This patch series cleans up some misconceptions about pm_ops. Some users of
the pm_ops structure attempt to use it to stop the user from entering suspend
to disk, this, however, is not possible since the user can always use
"shutdown" in /sys/power/disk and then the pm_ops are never invoked. Also,
platforms that don't support suspend to disk simply should not allow
configuring SOFTWARE_SUSPEND (read the help text on it, it only selects
suspend to disk and nothing else, all the other stuff depends on PM).
The pm_ops structure is actually intended to provide a way to enter
platform-defined sleep states (currently supported states are "standby" and
"mem" (suspend to ram)) and additionally (if SOFTWARE_SUSPEND is configured)
allows a platform to support a platform specific way to enter low-power mode
once everything has been saved to disk. This is currently only used by ACPI
(S4).
This patch:
The pm_ops.pm_disk_mode is used in totally bogus ways since nobody really
seems to understand what it actually does.
This patch clarifies the pm_disk_mode description.
It also removes all the arm and sh users that think they can veto suspend to
disk via pm_ops; not so since the user can always do echo shutdown >
/sys/power/disk, they need to find a better way involving Kconfig or such.
ACPI is the only user left with a non-zero pm_disk_mode.
The patch also sets the default mode to shutdown again, but when a new pm_ops
is registered its pm_disk_mode is selected as default, that way the default
stays for ACPI where it is apparently required.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: David Brownell <david-b@pacbell.net> Acked-by: Pavel Machek <pavel@ucw.cz> Cc: <linux-pm@lists.linux-foundation.org> Cc: Len Brown <lenb@kernel.org> Acked-by: Russell King <rmk@arm.linux.org.uk> Cc: Greg KH <greg@kroah.com> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Acked-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Robert Peterson [Mon, 30 Apr 2007 22:09:48 +0000 (15:09 -0700)]
Extend print_symbol capability
Today's print_symbol function dumps a kernel symbol with printk. This
patch extends the functionality of kallsyms.c so that the symbol lookup
function may be used without the printk. This is useful for modules that
want to dump symbols elsewhere, for example, to debugfs. I intend to use
the new function call in the GFS2 file system (which will be a separate
patch).
[akpm@linux-foundation.org: build fix]
[clameter@sgi.com: sprint_symbol should return length of string like sprintf] Signed-off-by: Robert Peterson <rpeterso@redhat.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Roman Zippel <zippel@linux-m68k.org> Cc: "Randy.Dunlap" <rdunlap@xenotime.net> Cc: Sam Ravnborg <sam@ravnborg.org> Acked-by: Paulo Marques <pmarques@grupopie.com> Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David S. Miller [Mon, 30 Apr 2007 21:51:58 +0000 (14:51 -0700)]
[UDP]: Do not allow specific bind when wildcard bind exists.
When allocating local ports, do not allow a bind to a port
with a specific local address when a bind to that port with
a wildcard local address already exists.
Noticed by Linus.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 30 Apr 2007 20:35:29 +0000 (13:35 -0700)]
[IPV4] UDP: Fix endianness bugs in hashing changes.
I accidently applied an earlier version of Eric Dumazet's patch, from
March 21st. His version from March 30th didn't have these bugs, so
this just interdiffs to the correct patch.
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: (56 commits)
ieee1394: remove garbage from Kconfig
ieee1394: more help in Kconfig
ieee1394: ohci1394: Fix mistake in printk message.
ieee1394: ohci1394: remove unnecessary rcvPhyPkt bit flipping in LinkControl register
ieee1394: ohci1394: fix cosmetic problem in error logging
ieee1394: eth1394: send async streams at S100 on 1394b buses
ieee1394: eth1394: fix error path in module_init
ieee1394: eth1394: correct return codes in hard_start_xmit
ieee1394: eth1394: hard_start_xmit is called in atomic context
ieee1394: eth1394: some conditions are unlikely
ieee1394: eth1394: clean up fragment_overlap
ieee1394: eth1394: don't use alloc_etherdev
ieee1394: eth1394: omit useless set_mac_address callback
ieee1394: eth1394: CONFIG_INET is always defined
ieee1394: eth1394: allow MTU bigger than 1500
ieee1394: unexport highlevel_host_reset
ieee1394: eth1394: contain host reset
ieee1394: eth1394: shorter error messages
ieee1394: eth1394: correct a memset argument
ieee1394: eth1394: refactor .probe and .update
...
Merge branch 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid: (21 commits)
USB HID: don't warn on idVendor == 0
USB HID: add 'quirks' module parameter
USB HID: add support for dynamically-created quirks
USB HID: clarify static quirk handling as squirks
USB HID: encapsulate quirk handling into hid-quirks.c
USB HID: EMS USBII device needs HID_QUIRK_MULTI_INPUT
HID: update copyright and authorship macro
HID: introduce proper zeroing of unused bits in output reports
USB HID: add support for WiseGroup MP-8800 Quad Joypad
USB HID: add FF support for Logitech Force 3D Pro Joystick
USB HID: numlock quirk for dell W7658 keyboard
USB HID: Logitech MX3000 keyboard needs report descriptor quirk
USB HID: extend quirk for Logitech S510 keyboard
USB HID: usbkbd/usbmouse - handle errors when registering devices
USB HID: add QUIRK_HIDDEV for Belkin Flip KVM
HID: enable dead keys on a belkin wireless keyboard
USB HID: Thustmaster firestorm dual power v1 support
USB HID: specify explicit size for hid_blacklist.quirks
USB HID: fix retry & reset logic
USB HID: consolidate vendor/product ids
...
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
[IPV4] SNMP: Support OutMcastPkts and OutBcastPkts
[IPV4] SNMP: Support InMcastPkts and InBcastPkts
[IPV4] SNMP: Support InTruncatedPkts
[IPV4] SNMP: Support InNoRoutes
[SNMP]: Add definitions for {In,Out}BcastPkts
[TCP] FRTO: RFC4138 allows Nagle override when new data must be sent
[TCP] FRTO: Delay skb available check until it's mandatory
[XFRM]: Restrict upper layer information by bundle.
[TCP]: Catch skb with S+L bugs earlier
[PATCH] INET : IPV4 UDP lookups converted to a 2 pass algo
[L2TP]: Add the ability to autoload a pppox protocol module.
[SKB]: Introduce skb_queue_walk_safe()
[AF_IUCV/IUCV]: smp_call_function deadlock
[IPV6]: Fix slab corruption running ip6sic
[TCP]: Update references in two old comments
[XFRM]: Export SPD info
[IPV6]: Track device renames in snmp6.
[SCTP]: Fix sctp_getsockopt_local_addrs_old() to use local storage.
[NET]: Remove NETIF_F_INTERNAL_STATS, default to internal stats.
[NETPOLL]: Remove CONFIG_NETPOLL_RX
...
Merge branch 'for-linus' of git://git.kernel.dk/data/git/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/data/git/linux-2.6-block:
[PATCH] elevator: elv_list_lock does not need irq disabling
[BLOCK] Don't pin lots of memory in mempools
cfq-iosched: speedup cic rb lookup
ll_rw_blk: add io_context private pointer
cfq-iosched: get rid of cfqq hash
cfq-iosched: tighten queue request overlap condition
cfq-iosched: improve sync vs async workloads
cfq-iosched: never allow an async queue idling
cfq-iosched: get rid of ->dispatch_slice
cfq-iosched: don't pass unused preemption variable around
cfq-iosched: get rid of ->cur_rr and ->cfq_list
cfq-iosched: slice offset should take ioprio into account
[PATCH] cfq-iosched: style cleanups and comments
cfq-iosched: sort IDLE queues into the rbtree
cfq-iosched: sort RT queues into the rbtree
[PATCH] cfq-iosched: speed up rbtree handling
cfq-iosched: rework the whole round-robin list concept
cfq-iosched: minor updates
cfq-iosched: development update
cfq-iosched: improve preemption for cooperating tasks
[IPV4] SNMP: Support OutMcastPkts and OutBcastPkts
A transmitted IP multicast datagram should be counted as OutMcastPkts.
By the same token, a transmitted IP broadcast datagram should be
counted as OutBcastPkts.
Signed-off-by: Mitsuru Chinen <mitch@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
A received IP multicast datagram should be counted as InMcastPkts.
By the same token, a received IP broadcast datagram should be
counted as InBcastPkts.
Signed-off-by: Mitsuru Chinen <mitch@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Mon, 30 Apr 2007 07:42:20 +0000 (00:42 -0700)]
[TCP] FRTO: RFC4138 allows Nagle override when new data must be sent
This is a corner case where less than MSS sized new data thingie
is awaiting in the send queue. For F-RTO to work correctly, a
new data segment must be sent at certain point or F-RTO cannot
be used at all. RFC4138 allows overriding of Nagle at that
point.
Implementation uses frto_counter states 2 and 3 to distinguish
when Nagle override is needed.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
[XFRM]: Restrict upper layer information by bundle.
On MIPv6 usage, XFRM sub policy is enabled.
When main (IPsec) and sub (MIPv6) policy selectors have the same
address set but different upper layer information (i.e. protocol
number and its ports or type/code), multiple bundle should be created.
However, currently we have issue to use the same bundle created for
the first time with all flows covered by the case.
It is useful for the bundle to have the upper layer information
to be restructured correctly if it does not match with the flow.
1. Bundle was created by two policies
Selector from another policy is added to xfrm_dst.
If the flow does not match the selector, it goes to slow path to
restructure new bundle by single policy.
2. Bundle was created by one policy
Flow cache is added to xfrm_dst as originated one. If the flow does
not match the cache, it goes to slow path to try searching another
policy.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Mon, 30 Apr 2007 07:57:33 +0000 (00:57 -0700)]
[TCP]: Catch skb with S+L bugs earlier
SACKED_ACKED and LOST are mutually exclusive with SACK, thus
having their sum larger than packets_out is bug with SACK.
Eventually these bugs trigger traps in the tcp_clean_rtx_queue
with SACK but it's much more informative to do this here.
Non-SACK TCP, however, could get more than packets_out duplicate
ACKs which each increment sacked_out, so it makes sense to do
this kind of limitting for non-SACK TCP but not for SACK enabled
one. Perhaps the author had the opposite in mind but did the
logic accidently wrong way around? Anyway, the sacked_out
incrementer code for non-SACK already deals this issue before
calling sync_left_out so this trapping can be done
unconditionally.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 30 Apr 2007 07:26:00 +0000 (00:26 -0700)]
[PATCH] INET : IPV4 UDP lookups converted to a 2 pass algo
Some people want to have many UDP sockets, binded to a single port but
many different addresses. We currently hash all those sockets into a
single chain. Processing of incoming packets is very expensive,
because the whole chain must be examined to find the best match.
I chose in this patch to hash UDP sockets with a hash function that
take into account both their port number and address : This has a
drawback because we need two lookups : one with a given address, one
with a wildcard (null) address.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we scale the mempool sizes depending on memory installed
in the machine, except for the bio pool itself which sits at a fixed
256 entry pre-allocation.
There's really no point in "optimizing" this OOM path, we just need
enough preallocated to make progress. A single unit is enough, lets
scale it down to 2 just to be on the safe side.
This patch saves ~150kb of pinned kernel memory on a 32-bit box.
cfq hash is no more necessary. We always can get cfqq from io context.
cfq_get_io_context_noalloc() function is introduced, because we don't
want to allocate cic on merging and checking may_queue. In order to
identify sync queue we've used hash key = CFQ_KEY_ASYNC. Since hash is
eliminated we need to use other criterion: sync flag for queue is added.
In all places where we dig in rb_tree we're in current context, so no
additional locking is required.
Advantages of this patch: no additional memory for hash, no seeking in
hash, code is cleaner. But it is necessary now to seek cic in per-ioc
rbtree, but it is faster:
- most processes work only with few devices
- most systems have only few block devices
- it is a rb-tree
Signed-off-by: Vasily Tarasov <vtaras@openvz.org>
Changes by me:
- Merge into CFQ devel branch
- Get rid of cfq_get_io_context_noalloc()
- Fix various bugs with dereferencing cic->cfqq[] with offset other
than 0 or 1.
- Fix bug in cfqq setup, is_sync condition was reversed.
- Fix bug where only bio_sync() is used, we need to check for a READ too
It's only used for preemption now that the IDLE and RT queues also
use the rbtree. If we pass an 'add_front' variable to
cfq_service_tree_add(), we can set ->rb_key to 0 to force insertion
at the front of the tree.
Currently CFQ does a linked insert into the current list for RT
queues. We can just factor the class into the rb insertion,
and then we don't have to treat RT queues in a special way. It's
faster, too.
For cases where the rbtree is mainly used for sorting and min retrieval,
a nice speedup of the rbtree code is to maintain a cache of the leftmost
node in the tree.
Also spotted in the CFS CPU scheduler code.
Improved by Alan D. Brunelle <Alan.Brunelle@hp.com> by updating the
leftmost hint in cfq_rb_first() if it isn't set, instead of only
updating it on insert.
cfq-iosched: rework the whole round-robin list concept
Drawing on some inspiration from the CFS CPU scheduler design, overhaul
the pending cfq_queue concept list management. Currently CFQ uses a
doubly linked list per priority level for sorting and service uses.
Kill those lists and maintain an rbtree of cfq_queue's, sorted by when
to service them.
This unfortunately means that the ionice levels aren't as strong
anymore, will work on improving those later. We only scale the slice
time now, not the number of times we service. This means that latency
is better (for all priority levels), but that the distinction between
the highest and lower levels aren't as big.
- Move the queue_new flag clear to when the queue is selected
- Only select the non-first queue in cfq_get_best_queue(), if there's
a substantial difference between the best and first.
- Get rid of ->busy_rr
- Only select a close cooperator, if the current queue is known to take
a while to "think".
- Implement logic for detecting cooperating processes, so we
choose the best available queue whenever possible.
- Improve residual slice time accounting.
- Remove dead code: we no longer see async requests coming in on
sync queues. That part was removed a long time ago. That means
that we can also remove the difference between cfq_cfqq_sync()
and cfq_cfqq_class_sync(), they are now indentical. And we can
kill the on_dispatch array, just make it a counter.
- Allow a process to go into the current list, if it hasn't been
serviced in this scheduler tick yet.
Possible future improvements including caching the cfqq lookup
in cfq_close_cooperator(), so we don't have to look it up twice.
cfq_get_best_queue() should just use that last decision instead
of doing it again.
Jens Axboe [Wed, 14 Feb 2007 18:59:49 +0000 (19:59 +0100)]
cfq-iosched: improve preemption for cooperating tasks
When testing the syslet async io approach, I discovered that CFQ
sometimes didn't perform as well as expected. cfq_should_preempt()
needs to better check for cooperating tasks, so fix that by allowing
preemption of an equal priority queue if the recently queued request
is as good a candidate for IO as the one we are currently waiting for.
Paul Mackerras [Mon, 30 Apr 2007 03:03:39 +0000 (13:03 +1000)]
[POWERPC] Remove dev_dbg redefinition in drivers/ps3/vuart.c
Commit 404d5b185b4eb56d6fa2f7bd27833f8df1c38ce4 changed the definition
of dev_dbg in the !DEBUG case from being a #define to being a static
inline. There was code in drivers/ps3/vuart.c to do exactly that,
which fails to compile now. This fixes it by removing the redefinition,
as the redefinition is now superfluous.
Andrew Morton [Thu, 26 Apr 2007 07:07:05 +0000 (00:07 -0700)]
[POWERPC] ppc4xx_sgdma needs dma-mapping.h
For dma_alloc_*()
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/sysdev/timer.c:51: error: variable `timer_sysclass' has
initializer but incomplete type
arch/powerpc/sysdev/timer.c:52: error: unknown field `resume' specified in initializer
<etc>
Signed-off-by: Srinivasa Ds <srinivasa@in.ibm.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Adrian Bunk [Sat, 28 Apr 2007 19:19:56 +0000 (05:19 +1000)]
[POWERPC] Remove the unused HTDMSOUND driver
Recently, someone fixed a syntax error in the HTDMSOUND driver
introduced 4 years ago.
Unfortunately not by trying to compile this driver for his hardware but
by code inspection - which seems to be a strong indication that there
are no users left for this OSS sound driver.
This patch therefore removes it.
Signed-off-by: Adrian Bunk <bunk@stusta.de> Acked-by: Dan Malek <dan@embeddedalley.com> Acked-by: Marcelo Tosatti <marcelo@kvack.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
projects / linux-2.6 / log