Andy Fleming [Wed, 11 Jul 2007 16:43:07 +0000 (11:43 -0500)]
Fix RGMII-ID handling in gianfar
The TSEC/eTSEC can detect the interface to the PHY automatically,
but it isn't able to detect whether the RGMII connection needs internal
delay. So we need to detect that change in the device tree, propagate
it to the platform data, and then check it if we're in RGMII. This fixes
a bug on the 8641D HPCN board where the Vitesse PHY doesn't use the delay
for RGMII.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Andy Fleming [Wed, 11 Jul 2007 16:42:35 +0000 (11:42 -0500)]
Fix Vitesse RGMII-ID support
The Vitesse PHY on the 8641D needs to be set up with internal delay to
work in RGMII mode. So we add skew when it is set to RGMII_ID mode.
Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Haruki Dai <Dai.Haruki@freescale.com> Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Andy Fleming [Tue, 10 Jul 2007 22:28:49 +0000 (17:28 -0500)]
Add phy-connection-type to gianfar nodes
The TSEC/eTSEC automatically detect their PHY interface type, unless
the type is RGMII-ID (RGMII with internal delay). In that situation,
it just detects RGMII. In order to fix this, we need to pass in rgmii-id
if that is the connection type.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Andy Fleming [Tue, 10 Jul 2007 21:42:04 +0000 (16:42 -0500)]
Fix Vitesse 824x PHY interrupt acking
The Vitesse 824x PHY doesn't allow an interrupt to be cleared if
the mask bit for that interrupt isn't set. This means that the PHY
Lib's order of handling interrupts (disable, then clear) breaks on this
PHY. However, clearing then disabling the interrupt opens up the code
for a silly race condition. So rather than change the PHY Lib, we change
the Vitesse driver so it always clears interrupts before disabling them.
Further, the ack function only clears the interrupt if interrupts are
enabled.
Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Acked-by: Haiying Wang <Haiying.Wang@freescale.com>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
[AVR32] Initialize phy_mask for both macb devices
[AVR32] Fix atomic_add_unless() and atomic_sub_unless()
[AVR32] Correct misspelled CONFIG_BLK_DEV_INITRD variable.
[AVR32] Fix build error in parse_tag_rdimg()
[AVR32] Don't wire up macb0 unless SW6 is in default position
[AVR32] Wire up SSC platform device 0 as TX on ATSTK1000 board
[AVR32] Add Atmel SSC driver platform device to AT32AP architecture
[AVR32] Remove optimization of unaligned word loads
[AVR32] Make STK1000 mux settings configurable
[AVR32] CPU frequency scaling for AT32AP
[AVR32] Split SM device into PM, RTC, WDT and EIC
[AVR32] faster avr32 unaligned access
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup:
[PATCH] x86: do not recompile boot for each build
[x86 setup] Save/restore DS around invocations of INT 10h
[x86 setup] VGA: Clear the Protect bit before setting the vertical height
[x86 setup] Fix assembly constraints
[x86 setup] build/tools.c: fix comment
[x86 setup] MAINTAINERS: document x86 setup code git tree
Peter Zijlstra [Wed, 18 Jul 2007 18:59:22 +0000 (20:59 +0200)]
i386: fixup TRACE_IRQ breakage
The TRACE_IRQS_ON function in iret_exc: calls a C function without
ensuring that the segments are set properly. Move the trace function and
the enabling of interrupt into the C stub.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The STK1000 uses pullups on the MDIO lines to the PHY, but they are
too weak. This causes the PHY layer to detect PHYs on all possible MII
addresses. Mask out all but the correct address to prevent this from
happening.
[AVR32] Fix atomic_add_unless() and atomic_sub_unless()
These functions depend on "result" being initalized to 0, but "result"
is not included as an input constraint to the inline assembly block
following its initialization, only as an output constraint. Thus gcc
thinks it doesn't need to initialize it, so result ends up undefined
if the "unless" condition is true.
This fixes an oops in sunrpc where the faulty atomics caused
rpciod_up() to not start the workqueue as it should.
This code is inside an #ifdef with a misspelled config symbol, so it
hasn't been used for a long time. Fix it before fixing the config
symbol to keep bisection working.
[AVR32] Remove optimization of unaligned word loads
If we let unaligned word loads bypass the generic unaligned handling,
gcc may combine it with a swap.b instruction and turn it into a ldwsp
instruction, which does not work with unaligned addresses.
Revert the optimization to prevent the RNDIS driver from crashing.
Hopefully we'll figure something out later (it may be better to do the
optimization in gcc.)
David Brownell [Tue, 12 Jun 2007 12:34:47 +0000 (14:34 +0200)]
[AVR32] Make STK1000 mux settings configurable
This adds some STK1002-specific config options covering the jumper settings,
so the kernel can automatically be configured to include the relevant devices.
One of them replaces the previous internal SW2_DEFAULT setting; SPI config
is affected by two of the jumpers; and a fourth one switches between LCD and
the second Ethernet connector. (There's more that to be done.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch enables CPU frequency scaling for AT32AP devices. This will
enable the CPU to scale between the speed of the high speed bus and
the master clock and thus save some power.
The patch also adds a parent to cpu_clk and a cpu_clk_set_rate to
enable changing the CPU clock divider in a sane way.
The driver does not check if the given rate is 0, thus resulting in a
div by 0. I think this check should be go into the clk_set_rate
framework, and not here.
Tested on AT32AP7000/ATSTK1000.
Hardware documentation can be found in the AT32AP7000 datasheet.
Split the SM platform device into separate platform devices for PM,
RTC, WDT and EIC. This is more correct according to the documentation
and allows us to simplify the code a little.
Also turn the EIC driver into a real platform driver.
H. Peter Anvin [Mon, 16 Jul 2007 18:58:24 +0000 (11:58 -0700)]
[x86 setup] Save/restore DS around invocations of INT 10h
There exists at least one card, Trident TVGA8900CL (BIOS dated 1992/9/8)
which clobbers DS when "scrolling in an SVGA text mode of more than
800x600 pixels." Although we are extremely unlikely to run into that
situation, it is cheap insurance to save and restore DS, and it only adds
a grand total of 50 bytes to the total output.
Pointed out by Etienne Lorrain.
Cc: Etienne Lorrain <etienne_lorrain@yahoo.fr> Signed-off-by: H. Peter Anvin <hpa@zytor.com>
H. Peter Anvin [Tue, 17 Jul 2007 23:16:10 +0000 (16:16 -0700)]
[x86 setup] VGA: Clear the Protect bit before setting the vertical height
If the user has asked for the vertical height registers to be recomputed
by setting bit 15 in the video mode number, we do so without clearing the
Protect bit in the Vertical Retrace Register before setting the Overflow
register. As a result, if the VGA BIOS had set the Protect bit, the
write to the Overflow register will be dropped, and bits [9:8] of the
vertical height will be left unchanged.
This is a bug imported from the assembly version of this code. It was
pointed out by Etienne Lorrain.
Cc: Etienne Lorrain <etienne_lorrain@yahoo.fr> Signed-off-by: H. Peter Anvin <hpa@zytor.com>
H. Peter Anvin [Sat, 14 Jul 2007 23:47:13 +0000 (16:47 -0700)]
[x86 setup] Fix assembly constraints
Fix incorrect assembly constraints. In particular, fix memory
constraints used inside push..pop, which can cause invalid operation
since gcc may generate %esp-relative references.
Additionally:
outl() should have "dN" not "dn".
query_mca() shouldn't listen 16/32-bit registers in an 8-bit only
context.
has_eflag(): the "mask" is only used well after both the stack pointer
and the output registers have been touched; this requires the output
registers to be earlyclobbers (=&) and the input to exclude memory (so
"ri", not "g").
Thanks to Etienne Lorrain and Chuck Ebbert for prompting this review.
Cc: Etienne Lorrain <etienne_lorrain@yahoo.fr> Cc: Chuck Ebbert <cebbert@redhat.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com>
H. Peter Anvin [Fri, 13 Jul 2007 23:28:27 +0000 (16:28 -0700)]
[x86 setup] build/tools.c: fix comment
Correct a comment in arch/i386/boot/build/tools.c; we now build the
kernel from only two components instead of three, since the boot
sector has been integrated in the setup code.
Merge branch 'master' of ssh://master.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb
* 'master' of ssh://master.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (126 commits)
V4L/DVB (5847): Clean up schedule_timeout calls in cpia2 and ivtv code
V4L/DVB (5846): Clean up setting state and scheduling timeouts
V4L/DVB (5844): ivtv: add high volume debugging flag
V4L/DVB (5843): ivtv: fix missing signal_pending check.
V4L/DVB (5842): ivtv: Add locking to ensure stream setup is atomic.
V4L/DVB (5841): tveeprom: add support for Philips FQ1216LME MK3 tuner.
V4L/DVB (5840): fix dst and cx24123: tune() callback changed signess for delay
V4L/DVB (5838): dvb-core: Fix signedness warnings (gcc 4.1.1, kernel 2.6.22)
V4L/DVB (5837): stv0299: Fix signedness warning (gcc 4.1.1, kernel 2.6.22)
V4L/DVB (5836): dvb-ttpci: re-initialize aspect ratio and pan scan after arm crash
V4L/DVB (5835): saa7146/dvb-ttpci: Fix signedness warnings (gcc 4.1.1, kernel 2.6.22)
V4L/DVB (5834): dvb-core: fix signedness warnings and const stripping
V4L/DVB (5832): ir-common: optimize bit extract function
V4L/DVB (5831): stradis: use ARRAY_SIZE
V4L/DVB (5829): Firmware extract and loading for opera dvb-usb update
V4L/DVB (5828): Kconfig: Added GemTek USB radio and removed experimental dependency.
V4L/DVB (5826): Usbvision: video mux cleanup
V4L/DVB (5825): Alter the tuner type for the WinTV USB UK PAL model.
V4L/DVB (5824): Usbvision: Hauppauge WinTV USB SECAM_L fix
V4L/DVB (5821): Saa7134: add remote control support for LifeView FlyDVB-S LR300
...
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: extent macros cleanup
Fix compilation with EXT_DEBUG, also fix leXX_to_cpu conversions.
ext4: remove extra IS_RDONLY() check
ext4: Use is_power_of_2()
Use zero_user_page() in ext4 where possible
ext4: Remove 65000 subdirectory limit
ext4: Expand extra_inodes space per the s_{want,min}_extra_isize fields
ext4: Add nanosecond timestamps
jbd2: Move jbd2-debug file to debugfs
jbd2: Fix CONFIG_JBD_DEBUG ifdef to be CONFIG_JBD2_DEBUG
ext4: Set the journal JBD2_FEATURE_INCOMPAT_64BIT on large devices
ext4: Make extents code sanely handle on-disk corruption
ext4: copy i_flags to inode flags on write
ext4: Enable extents by default
Change on-disk format to support 2^15 uninitialized extents
write support for preallocated blocks
fallocate support in ext4
sys_fallocate() implementation on i386, x86_64 and powerpc
Robert P. J. Day [Mon, 16 Jul 2007 13:47:51 +0000 (10:47 -0300)]
V4L/DVB (5847): Clean up schedule_timeout calls in cpia2 and ivtv code
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Tue, 10 Jul 2007 17:58:33 +0000 (14:58 -0300)]
V4L/DVB (5842): ivtv: Add locking to ensure stream setup is atomic.
Starting an MPEG and VBI capture simultaneously caused errors in
the VBI setup: this setup was done twice when it should be done
only for the first stream that is opened.
Added a mutex to prevent this from happening.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (5840): fix dst and cx24123: tune() callback changed signess for delay
tune() dvb_frontend callback changed delay signess:
int (*tune)(struct dvb_frontend* fe,
struct dvb_frontend_parameters* params,
unsigned int mode_flags,
- int *delay,
+ unsigned int *delay,
This change caused warnings on cx24123 and dst modules:
/home/v4l/master/v4l/cx24123.c:1034: warning: initialization from incompatible pointer type
/home/v4l/master/v4l/dst.c:1782: warning: initialization from incompatible pointer type
/home/v4l/master/v4l/dst.c:1808: warning: initialization from incompatible pointer type
/home/v4l/master/v4l/dst.c:1837: warning: initialization from incompatible pointer type
/home/v4l/master/v4l/dst.c:1860: warning: initialization from incompatible pointer type
This patch corrects the function prototype on both modules to follow the
core change.
V4L/DVB (5834): dvb-core: fix signedness warnings and const stripping
Make some pointers const, and then delete some now unnecessary casts,
which were the wrong signedness anyway, being used to strip the const
from another pointer.
Marco Gittler [Wed, 4 Jul 2007 22:18:34 +0000 (19:18 -0300)]
V4L/DVB (5829): Firmware extract and loading for opera dvb-usb update
Better way of creating and loading the firmware used.
Update for get_dvb_firmware script to extract the files for opera usb-box
Help file for creating the firmware added
Signed-off-by: Marco Gittler <g.marco@freenet.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thierry MERLE [Tue, 26 Jun 2007 19:35:30 +0000 (16:35 -0300)]
V4L/DVB (5826): Usbvision: video mux cleanup
- usbvision_muxsel simplified, now uses some well known constants.
- since the decoder needs to change input norm, call to muxsel added when
changing video standard.
Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (24 commits)
[NETFILTER]: xt_connlimit needs to depend on nf_conntrack
[NETFILTER]: ipt_iprange.h must #include <linux/types.h>
[IrDA]: Fix IrDA build failure
[ATM]: nicstar needs virt_to_bus
[NET]: move __dev_addr_discard adjacent to dev_addr_discard for readability
[NET]: merge dev_unicast_discard and dev_mc_discard into one
[NET]: move dev_mc_discard from dev_mcast.c to dev.c
[NETLINK]: negative groups in netlink_setsockopt
[PPPOL2TP]: Reset meta-data in xmit function
[PPPOL2TP]: Fix use-after-free
[PKT_SCHED]: Some typo fixes in net/sched/Kconfig
[XFRM]: Fix crash introduced by struct dst_entry reordering
[TCP]: remove unused argument to cong_avoid op
[ATM]: [idt77252] Rename CONFIG_ATM_IDT77252_SEND_IDLE to not resemble a Kconfig variable
[ATM]: [drivers] ioremap balanced with iounmap
[ATM]: [lanai] sram_test_word() must be __devinit
[ATM]: [nicstar] Replace C code with call to ARRAY_SIZE() macro.
[ATM]: Eliminate dead config variable CONFIG_BR2684_FAST_TRANS.
[ATM]: Replacing kmalloc/memset combination with kzalloc.
[NET]: gen_estimator deadlock fix
...
James Le Cuirot [Mon, 2 Jul 2007 15:53:25 +0000 (12:53 -0300)]
V4L/DVB (5821): Saa7134: add remote control support for LifeView FlyDVB-S LR300
It has been confirmed that the FlyDVB IR codes currently in the kernel
work with the LifeView FlyDVB-S LR300. This one line addition adds it
to the list of supported cards.
Signed-off-by: James Le Cuirot <chewi@aura-online.co.uk> Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (5820): Cleanup on cinergyT2: Remove unneeded if(1)
Before kernel 2.6.14, the driver checked for status before stopping the
thread. So, a compatibility test did exist. After 2.6.14, the
if (state)
were replaced by:
if (1)
However, it makes no sense to keep the if(1).
Some includes were added after some non-include macros, on old drivers.
Better to keep all includes at the beginning of the files. This change
also helps to make backports to properly work at the development tree.
Clean up the use of structure templates in cx88-i2c and cx88-vp3054-i2c.
For one thing, a real template is supposed to be read-only. And in some
cases it's more efficient to initialize the few fields we need
individually.
This clean-up shrinks cx88-i2c.o by 33% and cx88-vp3054-i2c.o by 49%
(x86_64).
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adrian Bunk [Sun, 1 Jul 2007 21:22:00 +0000 (18:22 -0300)]
V4L/DVB (5813): TUNER_TEA5761 kconfig fixes
The following doesn't make much sense:
drivers/media/video/Kconfig:
...
config TUNER_TEA5761
tristate "TEA 5761 radio tuner (EXPERIMENTAL)"
...
drivers/media/video/Makefile:
...
ifneq ($(CONFIG_TUNER_TEA5761),)
tuner-objs += tea5761.o
endif
...
With this setup, TUNER_TEA5761=m is equivalent to TUNER_TEA5761=y.
This patch therefore changes TUNER_TEA5761 to a bool.
The missing dependency on EXPERIMENTAL the prompt text indicates also
gets added by this patch.
Additionally, the Makefile entry can now be written in a more compact way.
Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Trent Piepho [Thu, 28 Jun 2007 20:51:08 +0000 (17:51 -0300)]
V4L/DVB (5805): Bttv: Fix problems with probing for non-existent tuners
The bttv driver has code to detect if a tda9887 is present, that was previous
used to auto-load the tda9887 driver. Now there is no tda9887 driver, so the
code is pointless; it just figures out if it should load the driver and then
does nothing.
For cards that are defined as having no tuner, the init code would still do
i2c probes for various tuner devices and auto-load the tuner module. That can
be skipped for cards that don't need it. The code is made to understand that
in addition to 'UNSET', 'TUNER_ABSENT' also means no tuner.
The tuner into printk()s are also made nicer. Levels are added, INFO or
WARNING, depending on the meaning. For cards with no tuner, or no tuner
defined, a more informative message is printed.
Card has no tuner, before patch:
bttv0: tuner type=-1
or
bttv0: tuner type=4
After patch:
bttv0: tuner absent
Card has a tuner, but the type isn't defined, before patch:
bttv0: tuner type=-1
After patch:
bttv0: tuner type unset [<- also warning now, as the tuner won't work right]
Michael Krufky [Wed, 27 Jun 2007 17:38:45 +0000 (14:38 -0300)]
V4L/DVB (5800): Tuner: correct description of Philips FCV1236D tuner
The old description was "Philips 1236D ATSC/NTSC dual in", which can be
confused with other Philips tuner models. This patch corrects the name
to "Philips FCV1236D ATSC/NTSC dual in", and updates the range and params
array names to match the description.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Remove hardcoded fcv1236d tuner programmming from or51211.c
- Alter dvb-bt8xx for the pcHDTV-2000 to use dvb-pll for fcv1236d support.
Thanks to Jarom Hatch <jshatch@gmail.com> for testing this change.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Potentially, all board types with I2C and IR support can use an i2c
based IR. Currently, the driver is selected only if bt848 or saa7134
boards are selected.
V4L/DVB (5783): Fix excess of debug messages on cx88-mpeg
Closes the issue opened on Kernel bugzilla:
http://bugzilla.kernel.org/show_bug.cgi?id=8383
There's no need to print timeout without debug turned on:
Apr 27 23:02:14 video kernel: cx88[1]/2-mpeg: cx8802_timeout
Michael Krufky [Tue, 12 Jun 2007 19:10:51 +0000 (16:10 -0300)]
V4L/DVB (5780): Dvb: Remove static dependencies on dvb-pll
This patch removes all static dependencies on the dvb-pll module.
All exported dvb_pll_desc's have been UNexported, and the caller
will reference the individual dvb_pll_desc by it's index in the
pll_list array.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Trent Piepho <xyzzy@speakeasy.org> Signed-off-by: Patrick Boettcher <pb@linuxtv.org> Acked-by: Oliver Endriss <o.endriss@gmx.de> Acked-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Trent Piepho [Sat, 2 Jun 2007 19:30:46 +0000 (16:30 -0300)]
V4L/DVB (5777): Dvb-pll digitv dvb-usb: Eliminate last user of dvb_pll_configure
The last user of dvb_pll_configure was the dvb-usb function
dvb_usb_tuner_calc_regs(), which was nothing more than a wrapper around
dvb_pll_configure(). It's just a copy of the functionality provided by
the tuner_ops calc_regs method, and can be deleted.
There were two users of dvb_usb_tuner_calc_regs().
One was dvb_usb_tuner_set_params_i2c(), which is converted to use
fe->ops.tuner_ops.calc_regs().
The other was the digitv driver. This driver can use one of two demods,
mt352 or nxt6000.
For the mt352, the driver would set tuner_ops.calc_regs to
dvb_usb_tuner_calc_regs().
We can just attach dvb_pll and use the tuner_ops.calc_regs() provided by
that module. For the nxt600, the driver would set tuner_ops.set_params
to digitv_nxt6000_tuner_set_params.
That function would in turn use dvb_usb_tuner_calc_regs().
We convert it to use tuner_ops.calc_regs() instead, and use
dvb_pll_attach.
The digitv_tuner_attach() needs to know which frontend was attached by
digitv_frontend_attach(), since the nxt6000 needs tuner_ops.set_params()
to be overridden with digitv_nxt6000_tuner_set_params().
So, to do this a digitv_state that says which frontend was used is added
to the dvb_usb_device private state field.
Rafał Bilski [Wed, 20 Jun 2007 08:36:26 +0000 (05:36 -0300)]
V4L/DVB (5775): Alsa fix for SAA7134 based "KNC One TV-Station DVR" card
Sound recording doesn't work for this card because ACNI and ACPF
are not set before snd_card_saa7134_capture_prepare(). As a result
timeout occurs. These registers aren't poked because thread
never gets wake up signal. ACNI initialization is done in the
thread.
Sound is muted when capture stops. Shouldn't be because it may
be used during TV playback.
Hans Verkuil [Sat, 16 Jun 2007 20:02:11 +0000 (17:02 -0300)]
V4L/DVB (5769): Ivtv: fix broken VBI output support
The old service_set_out setting was still tested, even though it no longer
was ever set and was in fact obsolete. This meant that everything that was
written to /dev/vbi16 was ignored. Removed the service_set_out variable
altogether and now it works again.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Luca Risolia [Wed, 13 Jun 2007 18:11:15 +0000 (15:11 -0300)]
V4L/DVB (5767): ZC0301 driver updates
- Make the driver depend on V4L2 only (KConfig)
- Better and safe locking mechanism of the device structure on open(), close()
and disconnect()
- Use kref for handling device deallocation
- Generic cleanups
Luca Risolia [Wed, 13 Jun 2007 17:52:01 +0000 (14:52 -0300)]
V4L/DVB (5766): ET61x251 driver updates
- Make the driver depend on V4L2 only (KConfig)
- Better and safe locking mechanism of the device structure on open(),
close() and disconnect()
- Use kref for handling device deallocation
- Generic cleanups
Luca Risolia [Wed, 13 Jun 2007 17:37:50 +0000 (14:37 -0300)]
V4L/DVB (5765): SN9C1xx driver updates
- Add support for pair OV7630+SN9C120
- Better and safe locking mechanism of the device structure on open(),
close() and disconnect()
- Use kref for handling device deallocation
- Generic cleanups
projects / linux-2.6 / log