Ayaz Abdulla [Tue, 23 Jan 2007 17:00:56 +0000 (12:00 -0500)]
forcedeth: tx max work
This patch adds a limit to how much tx work can be done in each
iteration of tx processing. If the max limit is reached, remaining tx
completions will be handled by timer interrupt.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ayaz Abdulla [Sun, 21 Jan 2007 23:10:47 +0000 (18:10 -0500)]
forcedeth: tx data path optimization
This patch optimizes the tx data paths and cleans up the code (removes
vlan from descr1/2 since only valid for desc3, changes to make code
easier to read, etc).
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ayaz Abdulla [Sun, 21 Jan 2007 23:10:42 +0000 (18:10 -0500)]
forcedeth: tx limiting
This patch optimizes the logic for tx limiting. It adds a flag to check
on the completion side instead of recalculating the number of empty
slots. Also, it removes the fields that were previous used for limiting
since they have no value.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ayaz Abdulla [Sun, 21 Jan 2007 23:10:37 +0000 (18:10 -0500)]
forcedeth: optimized routines
This patch breaks up the routines into two versions, one for legacy
descriptor versions (ver 1 and ver 2) and one for desc ver 3. This will
make the new desc functions more leaner and further reductions will be
made in next few patches.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jay Vosburgh [Sat, 20 Jan 2007 02:15:47 +0000 (18:15 -0800)]
bonding: modify sysfs support to permit multiple loads
The existing code would blindly attempt to create the
bonding_masters file (in /sys/class/net) every time the module was
loaded. When the module is loaded multiple times (which is the
historical method used by initscripts and sysconfig to create multiple
bonding interfaces), this caused load failure of the second module load
attempt, as the creation request would fail.
This changes the code to note the failure, arrange to not remove
the bonding_masters file upon module exit, and then return success.
Bonding interfaces created by the second or subsequent loads of
the module will not exist in bonding_masters. This is not a significant
change, as previously only the interfaces from the most recent load of
the module would be listed. Both situations are less than optimal, but
this case permits compatibility with existing distro configuration
scripts, and is consistent.
Note that previously, the sysfs create request would overwrite
the exsting bonding_masters file and succeed, allowing multiple loads of
the module. The sysfs code has recently changed to return an error if
the file being created already exists.
Patrick McHardy <kaber@trash.net>, who reported this problem,
observed crashes on the old kernel (before sysfs checked for
duplicates). I did not experience such crashes, but this change should
resolve them.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jay Vosburgh [Sat, 20 Jan 2007 02:15:31 +0000 (18:15 -0800)]
bonding: fix device name allocation error
The code to select names for the bonding interfaces was, for the
non-sysfs creation case, always using a hard-coded set of bond0, bond1,
etc, up to max_bonds. This caused conflicts for the second or
subsequent loads of the module.
Changed the code to obtain device names from dev_alloc_name().
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Akinobu Mita [Tue, 19 Dec 2006 21:09:08 +0000 (13:09 -0800)]
net: use bitrev8
Use bitrev8 for bmac, mace, macmace, macsonic, and skfp drivers.
[akpm@osdl.org: use the API, not the array] Cc: Jeff Garzik <jgarzik@pobox.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Mirko Lindner <mlindner@syskonnect.de> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Adrian Bunk [Tue, 12 Dec 2006 16:24:39 +0000 (17:24 +0100)]
bonding.h: "extern inline" -> "static inline"
"extern inline" generates a warning with -Wmissing-prototypes and I'm
currently working on getting the kernel cleaned up for adding this to
the CFLAGS since it will help us to avoid a nasty class of runtime
errors.
If there are places that really need a forced inline, __always_inline
would be the correct solution.
Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ron Mercer [Thu, 4 Jan 2007 00:26:08 +0000 (16:26 -0800)]
qla3xxx: Add support for Qlogic 4032 chip.
Qlogic 4032 chip is an incremental change from the 4022. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cleanup receive processing some more:
* do the reserve padding of skb during setup
* don't pass constants to get_packet
* do smart prefetch of skb
* make copybreak a module parameter
Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Adrian Bunk [Tue, 19 Dec 2006 21:08:48 +0000 (13:08 -0800)]
remove the broken SKMC driver
The SKMC driver has:
- already been marked as BROKEN in 2.6.0 three years ago and
- is still marked as BROKEN.
Drivers that had been marked as BROKEN for such a long time seem to be
unlikely to be revived in the forseeable future.
But if anyone wants to ever revive this driver, the code is still
present in the older kernel releases.
Signed-off-by: Adrian Bunk <bunk@stusta.de> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a driver for the Silan SC92031/Rsltek 8139D NIC chip.
This chip is found on at least one counterfeit Encore ENL832-TX-RENT NIC
[1], which came with a mini-CD with the 2.4 driver. A slightly older
version of the driver was found at [2]. The main difference between them
is that the newer one has a small bugfix in the RX path, a lot of
gratuitous renaming of functions, all the printable strings changed to show
as a "Rsltek 8139D" [sic], and a PCI ID of 8139 instead of 2031. The
driver on this patch is a rewrite of the vendor drivers (based mostly on
the older one).
Changes from the previous patch sent to netdev:
- Use MMIO instead of PIO
- Changed TX bounce buffers allocation
- Use skb_copy_and_csum_dev
- Several small bug fixes
- Tested for more than just a few minutes each time
[1] See http://www.encore-usa.com/faq.php under ENL832-TX-RENT for more
information
[2] Look for SL_LINUX.ZIP (which is really a .tar.gz) at
http://broadbandforum.in/dataone_Intex_LAN_cardlinux-t4207-s15.html
[3] To compile on 2.6.17, simply add back the last argument to the
interrupt handler in two places, and copy the boolean declarations
from 2.6.19
[akpm@osdl.org: build fixes] Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Arjan van de Ven [Tue, 12 Dec 2006 13:06:23 +0000 (14:06 +0100)]
remove NETIF_F_TSO ifdefery
Remove the NETIF_F_TSO #ifdef-ery in drivers/net; this was
for old-old-2.4 compat (even current 2.4 has NETIF_F_TSO)
but it's time to get rid of it by now.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Linas Vepstas [Wed, 13 Dec 2006 21:23:56 +0000 (15:23 -0600)]
Spidernet RX Debugging printout
Add some debugging and error printing.
The show_rx_chain() prints out the status of the rx chain,
which shows that the status of the descriptors gets
messed up after the second & subsequent RX ramfulls.
Print out contents of bad packets if error occurs.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Cc: James K Lewis <jklewis@us.ibm.com> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Linas Vepstas [Wed, 13 Dec 2006 21:23:01 +0000 (15:23 -0600)]
Spidernet Avoid possible RX chain corruption
Delete possible source of chain corruption; the hardware
already knows the location of the tail, and writing it
again is likely to mess it up.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Cc: James K Lewis <jklewis@us.ibm.com> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Linas Vepstas [Wed, 13 Dec 2006 21:22:04 +0000 (15:22 -0600)]
Spidernet Memory barrier
Add memory barrier to make sure that the rest of the
RX descriptor state is flushed to memory before we tell
the hardware that its ready to go.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Cc: James K Lewis <jklewis@us.ibm.com> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Linas Vepstas [Wed, 13 Dec 2006 21:20:59 +0000 (15:20 -0600)]
Spidernet RX Chain tail
Tell the hardware the location of the rx ring tail.
More punctuation cleanup.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Cc: James K Lewis <jklewis@us.ibm.com> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Linas Vepstas [Wed, 13 Dec 2006 21:19:54 +0000 (15:19 -0600)]
Spidernet Remove unused variable
Remove unused variable; this makes code easier to read.
Tweak commentary.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Cc: James K Lewis <jklewis@us.ibm.com> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Linas Vepstas [Wed, 13 Dec 2006 21:18:52 +0000 (15:18 -0600)]
Spidernet RX Refill
The invocation of the rx ring refill routine is haphazard,
it can be called from a central location.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Cc: James K Lewis <jklewis@us.ibm.com> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Linas Vepstas [Wed, 13 Dec 2006 21:17:39 +0000 (15:17 -0600)]
Spidernet Cleanup return codes
Simplify the somewhat convoluted use of return codes
in the rx buffer handling.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Cc: James K Lewis <jklewis@us.ibm.com> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Linas Vepstas [Wed, 13 Dec 2006 21:16:18 +0000 (15:16 -0600)]
Spidernet another skb mem leak
Another skb leak in an error branch. Fix this by adding
call to dev_kfree_skb_irq() after moving to a more
appropriate spot.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Cc: James K Lewis <jklewis@us.ibm.com> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Linas Vepstas [Wed, 13 Dec 2006 21:15:15 +0000 (15:15 -0600)]
Spidernet RX skb mem leak
One of the unlikely error branches has an skb memory leak.
Fix this by handling the error conditions consistently.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Cc: James K Lewis <jklewis@us.ibm.com> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Linas Vepstas [Wed, 13 Dec 2006 21:12:26 +0000 (15:12 -0600)]
Spidernet cleanup un-needed API
There is no need to pass a flag into spider_net_decode_one_descr()
so remove this, and perform some othre minor cleanup.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Cc: James K Lewis <jklewis@us.ibm.com> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Linas Vepstas [Wed, 13 Dec 2006 21:10:06 +0000 (15:10 -0600)]
Spidernet remove rxramfull tasklet
Get rid of the rxramfull tasklet, and let the NAPI poll routine
deal with this situation. (The rxramfull interrupt is simply
stating that the h/w has run out of room for incoming packets).
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Cc: James K Lewis <jklewis@us.ibm.com> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Linas Vepstas [Wed, 13 Dec 2006 21:08:25 +0000 (15:08 -0600)]
Spidernet add net_ratelimit to suppress long output
This patch adds net_ratelimit to many of the printks in order to
limit extraneous warning messages (created in response to Bug 28554).
This patch supercedes all previous ratelimit patches.
This has been tested, please apply.
From: James K Lewis <jklewis@us.ibm.com> Signed-off-by: James K Lewis <jklewis@us.ibm.com> Signed-off-by: Linas Vepstas <jlinas@austin.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Linas Vepstas [Wed, 13 Dec 2006 21:06:59 +0000 (15:06 -0600)]
Spidernet DMA coalescing
The current driver code performs 512 DMA mappings of a bunch of
32-byte ring descriptor structures. This is silly, as they are
all in contiguous memory. This patch changes the code to
dma_map_coherent() each rx/tx ring as a whole.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Cc: James K Lewis <jklewis@us.ibm.com> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Francois Romieu [Mon, 11 Dec 2006 23:13:48 +0000 (00:13 +0100)]
chelsio: tabulate the update of the statistic counters
Let's try to avoid some code duplication.
- cxgb2
The data are contiguous. Use plain memcpy.
- ixf1010/pm3393/vsc7326
The cast of &mac->stats to (u64 *) is not wonderful but it is not clear
if it is worth to add an ad-hoc union under the struct cmac_statistics.
vsc7326_reg.h suggests that more statistics could be available.
Francois Romieu [Tue, 5 Dec 2006 22:57:41 +0000 (23:57 +0100)]
chelsio: misc cleanups in sge
- duplicated code in sge::free_cmdQ_buffers ;
- NET_IP_ALIGN is already defined in (included) <linux/skbuff.h> ;
- pci_alloc_consistent() returns void * ;
- pci_alloc_consistent() returns a zeroed chunk of memory ;
- early return in restart_tx_queues.
[PATCH] softmac: avoid assert in ieee80211softmac_wx_get_rate
Unconfigured bcm43xx device can hit an assert() during wx_get_rate
queries. This is because bcm43xx calls ieee80211softmac_start late
(i.e. during open instead of probe).
Kai Engert [Tue, 12 Dec 2006 20:09:41 +0000 (21:09 +0100)]
[PATCH] prism54: add ethtool -i interface
Add support for "ethtool -i" to prism54 driver.
ethtool -i queries the specified device for
associated driver information.
This helps tools like Fedora's system-config-network to
provide GUI management of network devices.
I learned how to write this patch by reading the ipw2100
driver code.
Signed-off-by: Kai Engert <kengert@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Sun, 31 Dec 2006 05:30:32 +0000 (23:30 -0600)]
[PATCH] bcm43xx: Interrogate hardware-enable switch and update LEDs
The current bcm43xx driver ignores any wireless-enable switches on mini-PCI
and mini-PCI-E cards. This patch implements a new routine to interrogate the
radio hardware enabled bit in the interface, logs the initial state and any
changes in the switch (if debugging enabled), activates the LED to show the
state, and changes the periodic work handler to provide 1 second response
to switch changes and to account for changes in the periodic work specs.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Drake [Tue, 12 Dec 2006 01:26:11 +0000 (01:26 +0000)]
[PATCH] zd1211rw: Remove addressing abstraction
Instead of passing our own custom 32-bit addresses around and
translating them, this patch makes all our register address constants
absolute and removes the translation.
There are two ugly parts:
- fw_reg_addr() is needed to compute addresses of firmware registers, as this
is dynamic based upon firmware
- inc_addr() needs a small hack to handle byte vs word addressing
However, both of those are only small, and we don't use fw_regs a whole
lot anyway.
The bonuses here include simplicity and improved driver readability. Also, the
fact that registers are now referenced by 16-bit absolute addresses (as
opposed to 32-bit pseudo addresses) means that over 2kb compiled code size has
been shaved off.
Includes some touchups and sparse fixes from Ulrich Kunitz.
Signed-off-by: Daniel Drake <dsd@gentoo.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Drake [Tue, 12 Dec 2006 01:25:52 +0000 (01:25 +0000)]
[PATCH] zd1211rw: Consistency for address space constants
The zd1211rw address space has confused me once too many times. This
patch introduces the following naming notation:
Memory space is split into segments (cr, fw, eeprom) and segments may
contain components (e.g. boot code inside eeprom). These names are
arbitrary and only for the description below:
x_START: Absolute address of segment start
(previously these were named such as CR_BASE_OFFSET, but they weren't
really offsets unless you were considering them as an offset to 0)
x_LEN: Segment length
x_y_LEN: Length of component y of segment x
x_y_OFFSET: Relative address of component y into segment x. The absolute
address for this component is (x_START + x_y_OFFSET)
I also renamed EEPROM registers to EEPROM data. These 'registers' can't
be written to using standard I/O and really represent predefined data
from the vendor.
Signed-off-by: Daniel Drake <dsd@gentoo.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Drake [Tue, 12 Dec 2006 01:25:13 +0000 (01:25 +0000)]
[PATCH] zd1211rw: Generic HMAC initialization
Many of the registers written during ZD1211 HMAC initialization are
duplicated exactly for ZD1211B. Move the identical ones into a generic
part, and write the hardware-specific ones separately.
Signed-off-by: Daniel Drake <dsd@gentoo.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver was still mis-calculating the number of bytes sent during
transmit, now the driver computes what appears to be exactly 100%
correct byte counts (not including CRC) when figuring out how many
bytes and frames were sent during the current transmit packet.
Bruce Allan [Thu, 18 Jan 2007 17:25:28 +0000 (09:25 -0800)]
e1000: clear ip csum info from context descriptor
Since the driver sets the IP checksum insertion bit (IXSM in Status
field) in transmit context descriptors, it should clear the IP checksum
bits of any garbage so as not to confuse the hardware.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Jesse Brandeburg [Thu, 18 Jan 2007 17:25:23 +0000 (09:25 -0800)]
e1000: fix NAPI performance on 4-port adapters
This fix attempts to solve a customer (IBM) reported issue with NAPI
enabled e1000 having bad performance when transmitting simultaneously
on four ports. The issue comes down to an interaction between NAPI,
hardware interrupt balancing, and the driver rescheduling poll on
the same processor. Try to fix by allowing the driver to re-enable
interrupts sooner instead of polling one more time, when there was
recently all the work completed in cleanup.
Jesse Brandeburg [Thu, 18 Jan 2007 17:25:21 +0000 (09:25 -0800)]
e1000: Fix MSI only interrupt handler routine
Unfortunately the read-free MSI interrupt handler needs to flush write
the icr register and thus we can't be read-free. Our MSI irq routine
thus becomes a lot more simpler since we don't need to track link state
anymore.
Frédéric Riss [Tue, 30 Jan 2007 20:41:17 +0000 (21:41 +0100)]
[PATCH] EFI x86: pass firmware call parameters on the stack
When calling into the EFI firmware, the parameters need to be passed on
the stack. The recent change to use -mregparm=3 breaks x86 EFI support.
This patch is needed to allow the new Intel-based Macs to suspend to ram
(efi.get_time is called during the suspend phase).
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] sd: udev accessing an uninitialized scsi_disk field results in a crash
[SCSI] st: A MTIOCTOP/MTWEOF within the early warning will cause the file number to be incorrect
[SCSI] qla4xxx: bug fixes
[SCSI] Fix scsi_add_device() for async scanning
John Keller [Sat, 3 Feb 2007 09:14:02 +0000 (01:14 -0800)]
[PATCH] Altix: more ACPI PRT support
The SN Altix platform does not conform to the IOSAPIC IRQ routing model.
Add code in acpi_unregister_gsi() to check if (acpi_irq_model ==
ACPI_IRQ_MODEL_PLATFORM) and return.
Due to an oversight, this code was not added previously when
similar code was added to acpi_register_gsi().
Signed-off-by: John Keller <jpk@sgi.com> Acked-by: Len Brown <lenb@kernel.org> Cc: "Luck, Tony" <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Sat, 3 Feb 2007 09:14:01 +0000 (01:14 -0800)]
[PATCH] revert blockdev direct io back to 2.6.19 version
Andrew Vasquez is reporting as-iosched oopses and a 65% throughput
slowdown due to the recent special-casing of direct-io against
blockdevs. We don't know why either of these things are occurring.
The patch minimally reverts us back to the 2.6.19 code for a 2.6.20
release.
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com> Cc: Ken Chen <kenchen@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Frysinger [Sat, 3 Feb 2007 09:13:55 +0000 (01:13 -0800)]
[PATCH] alpha: fix epoll syscall enumerations
We went and named them __NR_sys_foo instead of __NR_foo.
It may be too late to change this, but we can at least add the proper names
now.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Magnus Damm [Sat, 3 Feb 2007 09:13:48 +0000 (01:13 -0800)]
[PATCH] kexec: Avoid migration of already disabled irqs (ia64)
This patch fixes up ia64 kexec support for HP rx2620 hardware. It does
this by skipping migration of already disabled irqs. This is most likely a
problem on other ia64 platforms as well, but I've only been able to
reproduce it on one machine so far.
The full story is that handle_bad_irq() gets invoked before starting the
new kernel without this patch. This seems to happen when fixup_irqs()
calls generic_handle_irq() on already migrated (and disabled) irqs. So by
avoiding migration of disabled irqs we stay away of handle_bad_irq().
The code has been tested on three different ia64 machines, all with good
results. It is possible to trigger the same bug by offlining a processor
using echo 0 > /sys/devices/system/cpu/cpuX/online.
More detailed information is available in the following mail thread:
http://lists.osdl.org/pipermail/fastboot/2007-January/thread.html#5774
Signed-off-by: Magnus Damm <magnus@valinux.co.jp> Acked-by: Simon Horman <horms@verge.net.au> Acked-by: Zou, Nanhai <nanhai.zou@intel.com> Acked-by: Jay Lan <jlan@sgi.com> Acked-by: "Luck, Tony" <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
See report: http://marc.theaimsgroup.com/?l=linux-kernel&m=116599593200888&w=2
flush_workqueue() is not allowed to be called in the softirq context.
However, aio_complete() called from I/O interrupt can potentially call
put_ioctx with last ref count on ioctx and triggers bug. It is simply
incorrect to perform ioctx freeing from aio_complete.
The bug is trigger-able from a race between io_destroy() and aio_complete().
A possible scenario:
The real problem is that the condition check of ctx->reqs_active in
wait_for_all_aios() is incorrect that access to reqs_active is not
being properly protected by spin lock.
This patch adds that protective spin lock, and at the same time removes
all duplicate ref counting for each kiocb as reqs_active is already used
as a ref count for each active ioctx. This also ensures that buggy call
to flush_workqueue() in softirq context is eliminated.
Signed-off-by: "Ken Chen" <kenchen@google.com> Cc: Zach Brown <zach.brown@oracle.com> Cc: Suparna Bhattacharya <suparna@in.ibm.com> Cc: Benjamin LaHaise <bcrl@kvack.org> Cc: Badari Pulavarty <pbadari@us.ibm.com> Cc: <stable@kernel.org> Acked-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patrick McHardy [Sat, 3 Feb 2007 03:33:11 +0000 (19:33 -0800)]
[NETFILTER]: ctnetlink: fix compile failure with NF_CONNTRACK_MARK=n
CC net/netfilter/nf_conntrack_netlink.o
net/netfilter/nf_conntrack_netlink.c: In function 'ctnetlink_conntrack_event':
net/netfilter/nf_conntrack_netlink.c:392: error: 'struct nf_conn' has no member named 'mark'
make[3]: *** [net/netfilter/nf_conntrack_netlink.o] Error 1
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
[SCSI] sd: udev accessing an uninitialized scsi_disk field results in a crash
sd_probe() calls class_device_add() even before initializing the
sdkp->device variable. class_device_add() eventually results in the user mode
udev program to be called. udev program can read the the allow_restart
attribute of the newly created scsi device. This is resulting in a crash as
the show function for allow_restart (i.e sd_show_allow_restart) returns the
attribute value by reading the sdkp->device->allow_restart variable. As the
sdkp->device is not initialized before calling the user mode hotplug helper,
this results in a crash.
The patch below solves it by calling class_device_add() only after the
necessary fields in the scsi_disk structure are initialized properly.
Signed-off-by: Nagendra Singh Tomar <nagendra_tomar@adaptec.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Brian King [Tue, 30 Jan 2007 17:32:26 +0000 (11:32 -0600)]
libata: Initialize nbytes for internal sg commands
Some LLDDs, like ipr, use nbytes and pad_len to determine
the total data transfer length of a command. Make sure
nbytes gets initialized for internally generated commands.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan [Wed, 31 Jan 2007 17:47:24 +0000 (17:47 +0000)]
libata: Fix ata_busy_wait() kernel docs
> Looks like you should use ata_busy_wait() here, rather than reproducing
> the same code again.
It waits in 10uS chunks while 1uS chunks were used in the workaround.
Could indeed do that once I know the fix is right. While I'm at it the
ata_busy_wait kerneldoc is borked so here's a fix
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Fri, 2 Feb 2007 05:51:09 +0000 (14:51 +0900)]
ahci/pata_jmicron: fix JMicron quirk
For all JMicrons except for 361 and 368, AHCI mode enable bits in the
Control(1) should be set. This used to be done in both ahci and
pata_jmicron but while moving programming to PCI quirk, it was removed
from ahci part while still left in pata_jmicron.
The implemented JMicron PCI quirk was incorrect in that it didn't
program AHCI mode enable bits. If pata_jmicron is loaded first and
programs those bits, the ahci ports work; otherwise, ahci device
detection fails miserably.
This patch makes JMicron PCI quirk clear SATA IDE mode bits and set
AHCI mode bits and remove the respective part from pata_jmicron.
Tested on JMB361, 363 and 368.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
It's not wrong, but it's not right either, and everybody seems to agree
that the right fix is probably to do the ccr3 write after the ccr4 one
(and that we also should clean it up a bit). And after that we need to
really validate that all the bits that we write to ccr4 actually do
work.
The old 2.6.19 code was insane, and basically didn't change ccr4 at all
(even though it certainly looks like it was the *intent* to do so). So
let's revert the change that may fix things, just because it's not what
was actually ever tested when the code was written, even if it _was_ the
intent.
There's a discussion on http://lkml.org/lkml/2007/1/9/63 that was
started by the patch that now gets reverted, and that discussion may
well contain the proper long-term fix.
Suggested-by: Adrian Bunk <bunk@stusta.de> Acked-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jens Osterkamp [Thu, 1 Feb 2007 11:07:47 +0000 (12:07 +0100)]
spidernet : fix memory leak in spider_net_stop
We forget to call spider_net_free_rx_chain_contents which does the
actual dev_kfree_skb. New skbs are allocated from skbuff_head_cache
on each "ifconfig up" letting the cache grow infinitely.
This patch fixes it.
Signed-off-by: Jens Osterkamp <jens@de.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Auke Kok [Wed, 31 Jan 2007 19:02:46 +0000 (11:02 -0800)]
e100: fix napi ifdefs removing needed code
e100: fix napi ifdefs removing needed code
From: Auke Kok <auke-jan.h.kok@intel.com>
The e100 driver is NAPI mode only. We need to netif_poll_disable
during suspend and shutdown. The non-NAPI driver code was removed
and is only avaiable in the out-of-tree e100 kernel driver.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patrick McHardy [Fri, 2 Feb 2007 08:40:36 +0000 (00:40 -0800)]
[NET_SCHED]: act_ipt: fix regression in ipt action
The x_tables patch broke target module autoloading in the ipt action
by replacing the ipt_find_target call (which does autoloading) by
xt_find_target (which doesn't do autoloading). Additionally xt_find_target
may return ERR_PTR values in case of an error, which are not handled.
Use xt_request_find_target, which does both autoloading and ERR_PTR
handling properly. Also don't forget to drop the target module reference
again when xt_check_target fails.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6 / log