* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5255/1: Update jornada ssp to remove build errors/warnings
[ARM] omap: back out 'internal_clock' support
[ARM] 5249/1: davinci: remove redundant check in davinci_psc_config()
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Fix SMP bootup with CONFIG_STACK_DEBUG or ftrace.
sparc64: Fix OOPS in psycho_pcierr_intr_other().
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
e100: Use pci_pme_active to clear PME_Status and disable PME#
e1000: prevent corruption of EEPROM/NVM
forcedeth: call restore mac addr in nv_shutdown path
bnx2: Promote vector field in bnx2_irq structure from u16 to unsigned int
sctp: Fix oops when INIT-ACK indicates that peer doesn't support AUTH
sctp: do not enable peer features if we can't do them.
sctp: set the skb->ip_summed correctly when sending over loopback.
udp: Fix rcv socket locking
Manfred Spraul [Wed, 20 Aug 2008 13:39:59 +0000 (15:39 +0200)]
avr32: nmi_enter() without nmi_exit()
While updating the rcu code, I noticed that do_nmi() for AVR32 is odd:
There is an nmi_enter() call without an nmi_exit().
This can't be correct, it breaks rcu (at least the preempt version) and
lockdep.
[haavard.skinnemoen@atmel.com: fixed another case that returned directly] Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
On AVR32, all parameters beyond the 5th are passed on the stack. System
calls don't use the stack -- they borrow a callee-saved register
instead. This means that syscalls that take 6 parameters must be called
through a stub that pushes the last parameter on the stack.
This patch adds a stub for sync_file_range syscall on AVR32
architecture. Tested with uClibc snapshot.
md: Don't wait UNINTERRUPTIBLE for other resync to finish
When two md arrays share some block device (e.g each uses different
partitions on the one device), a resync of one array will wait for
the resync on the other to finish.
This can be a long time and as it currently waits TASK_UNINTERRUPTIBLE,
the softlockup code notices and complains.
So use TASK_INTERRUPTIBLE instead and make sure to flush signals
before calling schedule.
e100: Use pci_pme_active to clear PME_Status and disable PME#
Currently e100 uses pci_enable_wake() to clear pending wake-up events
and disable PME# during intitialization, but that function is not
suitable for this purpose, because it immediately returns error code
if device_may_wakeup() returns false for given device.
Make e100 use pci_pme_active(), which carries out exactly the
required operations, instead.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Christopher Li [Fri, 5 Sep 2008 21:04:05 +0000 (14:04 -0700)]
e1000: prevent corruption of EEPROM/NVM
Andrey reports e1000 corruption, and that a patch in vmware's ESX fixed
it.
The EEPROM corruption is triggered by concurrent access of the EEPROM
read/write. Putting a lock around it solve the problem.
[akpm@linux-foundation.org: use DEFINE_SPINLOCK to avoid confusing lockdep] Signed-off-by: Christopher Li <chrisl@vmware.com> Reported-by: Andrey Borzenkov <arvidjaar@mail.ru> Cc: Zach Amsden <zach@vmware.com> Cc: Pratap Subrahmanyam <pratap@vmware.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Cc: Bruce Allan <bruce.w.allan@intel.com> Cc: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com> Cc: John Ronciak <john.ronciak@intel.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Yinghai Lu [Sat, 13 Sep 2008 20:10:31 +0000 (13:10 -0700)]
forcedeth: call restore mac addr in nv_shutdown path
after
| commit f735a2a1a4f2a0f5cd823ce323e82675990469e2
| Author: Tobias Diedrich <ranma+kernel@tdiedrich.de>
| Date: Sun May 18 15:02:37 2008 +0200
|
| [netdrvr] forcedeth: setup wake-on-lan before shutting down
|
| When hibernating in 'shutdown' mode, after saving the image the suspend hook
| is not called again.
| However, if the device is in promiscous mode, wake-on-lan will not work.
| This adds a shutdown hook to setup wake-on-lan before the final shutdown.
|
| Signed-off-by: Tobias Diedrich <ranma+kernel@tdiedrich.de>
| Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
my servers with nvidia ck804 and mcp55 will reverse mac address with kexec.
it turns out that we need to restore the mac addr in nv_shutdown().
[akpm@linux-foundation.org: fix typo in printk] Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com> Cc: Tobias Diedrich <ranma+kernel@tdiedrich.de> Cc: Ayaz Abdulla <aabdulla@nvidia.com> Cc: Jeff Garzik <jeff@garzik.org> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Benjamin Li [Thu, 18 Sep 2008 23:46:11 +0000 (16:46 -0700)]
bnx2: Promote vector field in bnx2_irq structure from u16 to unsigned int
The bnx2 driver stores/uses the irq value from the pci_dev internally.
But when it stores the irq value, it has been performing an
integer demotion. Because of the recent changes made to
arch/x86/kernel/io_apic.c, the new method in creating the irq value
(using build_irq_for_pci_dev()) has exposed this bug on x86 systems.
Because of this demotion when calling request_irq() from
bnx2_request_irq(), the driver would get a return code of -EINVAL.
This is because the kernel could not find the requested irq descriptor.
By storing the irq value properly, the kernel can find the correct
irq descriptor and the bnx2 driver can operate normally.
Signed-off-by: Benjamin Li <benli@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
sctp: Fix oops when INIT-ACK indicates that peer doesn't support AUTH
If INIT-ACK is received with SupportedExtensions parameter which
indicates that the peer does not support AUTH, the packet will be
silently ignore, and sctp_process_init() do cleanup all of the
transports in the association.
When T1-Init timer is expires, OOPS happen while we try to choose
a different init transport.
The solution is to only clean up the non-active transports, i.e
the ones that the peer added. However, that introduces a problem
with sctp_connectx(), because we don't mark the proper state for
the transports provided by the user. So, we'll simply mark
user-provided transports as ACTIVE. That will allow INIT
retransmissions to work properly in the sctp_connectx() context
and prevent the crash.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
sctp: do not enable peer features if we can't do them.
Do not enable peer features like addip and auth, if they
are administratively disabled localy. If the peer resports
that he supports something that we don't, neither end can
use it so enabling it is pointless. This solves a problem
when talking to a peer that has auth and addip enabled while
we do not. Found by Andrei Pelinescu-Onciul <andrei@iptel.org>.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[ARM] 5255/1: Update jornada ssp to remove build errors/warnings
* Adds ssp functions into header so we don't get
"implicit declaration" error at builtime.
* Converts jornada_ssp_start/end functions into voids with
proper declarations (to avoid "prototype..." warning).
* Sorts include files in alphabetical order
* Minor comment changes
Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
sctp: set the skb->ip_summed correctly when sending over loopback.
Loopback used to clobber the ip_summed filed which sctp then used
to figure out if it needed to do checksumming or not. Now that
loopback doesn't do that any more, sctp needs to set the ip_summed
field correctly.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Wed, 17 Sep 2008 19:58:11 +0000 (20:58 +0100)]
[ARM] omap: back out 'internal_clock' support
The structures weren't ready for this change:
arch/arm/plat-omap/devices.c:320: error: 'struct omap_mmc_conf' has no member named 'internal_clock'
arch/arm/plat-omap/devices.c:326: error: implicit declaration of function 'omap_ctrl_readl'
arch/arm/plat-omap/devices.c:326: error: 'OMAP2_CONTROL_DEVCONF0' undeclared (first use in this function)
arch/arm/plat-omap/devices.c:328: error: implicit declaration of function 'omap_ctrl_writel'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Arjan van de Ven [Mon, 15 Sep 2008 23:43:18 +0000 (16:43 -0700)]
warn: Turn the netdev timeout WARN_ON() into a WARN()
this patch turns the netdev timeout WARN_ON_ONCE() into a WARN_ONCE(),
so that the device and driver names are inside the warning message.
This helps automated tools like kerneloops.org to collect the data
and do statistics, as well as making it more likely that humans
cut-n-paste the important message as part of a bugreport.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Miller [Tue, 16 Sep 2008 22:00:11 +0000 (15:00 -0700)]
Fix PNP build failure, bugzilla #11276
This fill fix the following regression list entry:
Bug-Entry : http://bugzilla.kernel.org/show_bug.cgi?id=11276
Subject : build error: CONFIG_OPTIMIZE_INLINING=y causes gcc 4.2 to do stupid things
Submitter : Randy Dunlap <randy.dunlap@oracle.com>
Date : 2008-08-06 17:18 (38 days old)
References : http://marc.info/?l=linux-kernel&m=121804329014332&w=4
http://lkml.org/lkml/2008/7/22/353
Handled-By : Bjorn Helgaas <bjorn.helgaas@hp.com>
Patch : http://lkml.org/lkml/2008/7/22/364
with what I believe is a better fix than the one referenced
in the regression entry above.
These PNP header interfaces try to work in such a way that
you can reference some of them even if PNP is not enabled,
and the compiler was expected to optimize everything away.
Which is mostly fine, except that there was one interface
for which there was not provided an inline "NOP" implementation.
Once we add that, all of these compile failures cannot handle
any more.
pnp: Provide NOP inline implementation of pnp_get_resource() when !PNP
Fixes kernel bugzilla #11276.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes kernel regression for 2.6.27-rc in
http://bugzilla.kernel.org/show_bug.cgi?id=11547
The change to split 8390 into old isa and non-isa versions
overlooked this driver.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit bc19d6e0b74ef03a3baf035412c95192b54dfc6f, which as
Larry Finger reports causes the radio LED on his system to no longer
respond to rfkill switch events.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net> Requested-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Herbert Xu [Mon, 15 Sep 2008 18:48:46 +0000 (11:48 -0700)]
udp: Fix rcv socket locking
The previous patch in response to the recursive locking on IPsec
reception is broken as it tries to drop the BH socket lock while in
user context.
This patch fixes it by shrinking the section protected by the
socket lock to sock_queue_rcv_skb only. The only reason we added
the lock is for the accounting which happens in that function.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Kim Phillips [Sun, 14 Sep 2008 20:41:19 +0000 (13:41 -0700)]
crypto: talitos - Avoid consecutive packets going out with same IV
The SEC's h/w IV out implementation DMAs the trailing encrypted payload
block of the last encryption to ctx->iv. Since the last encryption may
still be pending completion, we can sufficiently prevent successive
packets from being transmitted with the same IV by xoring with sequence
number.
Also initialize alg_list earlier to prevent oopsing on a failed probe.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Lee Nipper <lee.nipper@freescale.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] Fix PCI_DMA_BUS_IS_PHYS for ARM
[ARM] 5247/1: tosa: SW_EAR_IN support
[ARM] 5246/1: tosa: add proper clock alias for tc6393xb clock
[ARM] 5245/1: Fix warning about unused return value in drivers/pcmcia
[ARM] OMAP: Fix MMC device data
imx serial: fix rts handling for non imx1 based hardware
imx serial: set RXD mux bit on i.MX27 and i.MX31
i.MX serial: fix init failure
pcm037: add rts/cts support for serial port
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
niu: panic on reset
netlink: fix overrun in attribute iteration
[Bluetooth] Fix regression from using default link policy
ath9k: Assign seq# when mac80211 requests this
Alex Dubov [Sat, 13 Sep 2008 09:33:26 +0000 (02:33 -0700)]
memstick: fix MSProHG 8-bit interface mode support
- 8-bit interface mode never worked properly. The only adapter I have
which supports the 8b mode (the Jmicron) had some problems with its
clock wiring and they discovered it only now. We also discovered that
ProHG media is more sensitive to the ordering of initialization
commands.
- Make the driver fall back to highest supported mode instead of always
falling back to serial. The driver will attempt the switch to 8b mode
for any new MSPro card, but not all of them support it. Previously,
these new cards ended up in serial mode, which is not the best idea
(they work fine with 4b, after all).
- Edit some macros for better conformance to Sony documentation
Signed-off-by: Alex Dubov <oakad@yahoo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Sat, 13 Sep 2008 09:33:25 +0000 (02:33 -0700)]
rescan_partitions(): make device capacity errors non-fatal
Herton Krzesinski reports that the error-checking changes in 04ebd4aee52b06a2c38127d9208546e5b96f3a19 ("block/ioctl.c and
fs/partition/check.c: check value returned by add_partition") cause his
buggy USB camera to no longer mount. "The camera is an Olympus X-840.
The original issue comes from the camera itself: its format program
creates a partition with an off by one error".
Buggy devices happen. It is better for the kernel to warn and to proceed
with the mount.
Reported-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Cc: Abdel Benamrouche <draconux@gmail.com> Cc: Jens Axboe <jens.axboe@oracle.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Dooks [Sat, 13 Sep 2008 09:33:24 +0000 (02:33 -0700)]
spi_s3c24xx: fix section warning
Fix the section mismatch warning generated by the incorrect naming of
s3c24xx_spidrv which should be s3c24xx_spi_driver:
WARNING: drivers/spi/spi_s3c24xx.o(.data+0x4):
Section mismatch in reference from the variable s3c24xx_spidrv
to the (unknown reference) .exit.text:(unknown)
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
atmel_lcdfb: disable LCD and DMA engines when suspending
When suspending the system with atmel_lcdfb enabled, I sometimes see
this:
atmel_lcdfb atmel_lcdfb.0: FIFO underflow 0x10
Which can be explained by the fact that we're not stopping the LCD
controller and its DMA engine when suspending, we're just gating the
clocks to them.
There's another potential issue which may be harder to trigger but
much more nasty: If we gate the clocks at _just_ the right moment,
e.g. when the DMA engine is doing a bus transaction, we may cause the
DMA engine to violate the system bus protocol and cause a lockup.
Avoid these issues by shutting down the LCD controller before entering
suspend (and restarting it when resuming). This prevents the underrun
from happening in the first place, and prevents whatever nastiness is
happening when the bus clock stops in the middle of a DMA transfer.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Robin Holt [Sat, 13 Sep 2008 09:33:22 +0000 (02:33 -0700)]
ia64: fix panic during `modprobe -r xpc'
If you are on ia64 and you modprobe xpc then modprobe -r xpc, you
immediately get a panic. xpc depends on xp which depends on gru for a
symbol. That symbol is only used when we are running on UV hardware.
Currently, the GRU driver detects we are not on UV hardware and does no
initializing. It does not do the same check when unloading. As a result,
the gru driver attempts to tear down stuff that was not setup.
This is a simple two-line workaround to get us through this release. Once
2.6.28 is opened, we need to rework the symbols that xp is depending on
from gru so the gru driver can properly fail to load when hardware is not
available.
Signed-off-by: Robin Holt <holt@sgi.com> Cc: "Luck, Tony" <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm: mark the correct zone as full when scanning zonelists
The iterator for_each_zone_zonelist() uses a struct zoneref *z cursor when
scanning zonelists to keep track of where in the zonelist it is. The
zoneref that is returned corresponds to the the next zone that is to be
scanned, not the current one. It was intended to be treated as an opaque
list.
When the page allocator is scanning a zonelist, it marks elements in the
zonelist corresponding to zones that are temporarily full. As the
zonelist is being updated, it uses the cursor here;
if (NUMA_BUILD)
zlc_mark_zone_full(zonelist, z);
This is intended to prevent rescanning in the near future but the zoneref
cursor does not correspond to the zone that has been found to be full.
This is an easy misunderstanding to make so this patch corrects the
problem by changing zoneref cursor to be the current zone being scanned
instead of the next one.
Ned Forrester [Sat, 13 Sep 2008 09:33:18 +0000 (02:33 -0700)]
pxa2xx_spi: dma bugfixes
Fixes two DMA bugs in the pxa2xx_spi driver. The first bug is in all
versions of this driver; the second was introduced in the 2.6.20 kernel,
and prevents using the driver with chips like m25p16 flash (which can
issue large DMA reads).
1. Zero length transfers are permitted for use to insert timing,
but pxa2xx_spi.c will fail if this is requested in DMA mode.
Fixed by using programmed I/O (PIO) mode for such transfers.
2. Transfers larger than 8191 are not permitted in DMA mode. A
test for length rejects all large transfers regardless of DMA
or PIO mode. Worked around by rejecting only large transfers
with DMA mapped buffers, and forcing all other transfers
larger than 8191 to use PIO mode. A rate limited warning is
issued for DMA transfers forced to PIO mode.
This patch should apply to all kernels back to and including 2.6.20;
it was test patched against 2.6.20. An additional patch would be
required for older kernels, but those versions are very buggy anyway.
Signed-off-by: Ned Forrester <nforrester@whoi.edu> Cc: Vernon Sauder <vernoninhand@gmail.com> Cc: Eric Miao <eric.y.miao@gmail.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ned Forrester [Sat, 13 Sep 2008 09:33:17 +0000 (02:33 -0700)]
pxa2xx_spi: chipselect bugfixes
Fixes several chipselect bugs in the pxa2xx_spi driver. These bugs are in
all versions of this driver and prevent using it with chips like m25p16
flash.
1. The spi_transfer.cs_change flag is handled too early:
before spi_transfer.delay_usecs applies, thus making the
delay ineffective at holding chip select.
2. spi_transfer.delay_usecs is ignored on the last transfer
of a message (likewise not holding chipselect long enough).
3. If spi_transfer.cs_change is set on the last transfer, the
chip select is always disabled, instead of the intended
meaning: optionally holding chip select enabled for the
next message.
Those first three bugs were fixed with a relocation of delays
and chip select de-assertions.
4. If a message has the cs_change flag set on the last transfer,
and had the chip select stayed enabled as requested (see 3,
above), it would not have been disabled if the next message is
for a different chip. Fixed by dropping chip select regardless
of cs_change at end of a message, if there is no next message
or if the next message is for a different chip.
This patch should apply to all kernels back to and including 2.6.20;
it was test patched against 2.6.20. An additional patch would be
required for older kernels, but those versions are very buggy anyway.
Signed-off-by: Ned Forrester <nforrester@whoi.edu> Cc: Vernon Sauder <vernoninhand@gmail.com> Cc: Eric Miao <eric.y.miao@gmail.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Korsgaard [Sat, 13 Sep 2008 09:33:14 +0000 (02:33 -0700)]
spi_mpc83xx: fix clockrate calculation for low speed
Commit a61f5345 (spi_mpc83xx clockrate fixes) broke clockrate calculation
for low speeds. SPMODE_DIV16 should be set if the divider is higher than
64, not only if the divider gets clipped to 1024.
Furthermore, the clipping check was off by a factor 16 as well.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A "Quicklists: 0 kB" line has just started appearing in
/proc/meminfo, but most architectures (including x86) don't have
them configured, so #ifdef it, like the highmem lines.
And those architectures which do have quicklists configured are
using them for page tables: so let's place it next to PageTables.
Signed-off-by: Hugh Dickins <hugh@veritas.com> Acked-by: Christoph Lameter <cl@linux-foundation.org> Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Sesterhenn [Sat, 13 Sep 2008 09:33:12 +0000 (02:33 -0700)]
bfs: fix Lockdep warning
This fixes:
=============================================
[ INFO: possible recursive locking detected ] 2.6.27-rc5-00283-g70bb089 #68
---------------------------------------------
touch/6855 is trying to acquire lock:
(&info->bfs_lock){--..}, at: [<c02262f5>] bfs_delete_inode+0x9e/0x18c
but task is already holding lock:
(&info->bfs_lock){--..}, at: [<c0226c00>] bfs_create+0x45/0x187
other info that might help us debug this:
2 locks held by touch/6855:
#0: (&type->i_mutex_dir_key#5){--..}, at: [<c018ad13>] do_filp_open+0x10b/0x62f
#1: (&info->bfs_lock){--..}, at: [<c0226c00>] bfs_create+0x45/0x187
Li Zefan [Sat, 13 Sep 2008 09:33:09 +0000 (02:33 -0700)]
cpuset: hotplug documentation fix
If all the cpus in a cpuset are offlined, the tasks in it will be moved to
the nearest ancestor with non-empty cpus.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Acked-by: Paul Jackson <pj@sgi.com> Cc: Paul Menage <menage@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cpusets: restructure the function update_cpumask() and update_nodemask()
It might happen that 'echo 0 > /cpuset/sub/cpus' returned failure but 'cpus'
has been changed, because cpus was changed before calling heap_init() which
may return -ENOMEM.
This patch restores the orginal behavior.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Acked-by: Paul Menage <menage@google.com> Cc: Paul Jackson <pj@sgi.com> Cc: Miao Xie <miaox@cn.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
proc: more debugging for "already registered" case
Print parent directory name as well.
The aim is to catch non-creation of parent directory when proc_mkdir will
return NULL and all subsequent registrations go directly in /proc instead
of intended directory.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Fixed insane printk string while at it. - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I recently bought 3 HGST P7K500-series 500GB SATA drives and
had trouble accessing the block right on the LBA28-LBA48 border.
Here's how it fails (same for all 3 drives):
# dd if=/dev/sdc bs=512 count=1 skip=268435455 > /dev/null
dd: reading `/dev/sdc': Input/output error
0+0 records in
0+0 records out
0 bytes (0 B) copied, 0.288033 seconds, 0.0 kB/s
# dmesg
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: BMDMA stat 0x25
ata1.00: cmd c8/00:08:f8:ff:ff/00:00:00:00:00/ef tag 0 dma 4096 in
res 51/04:08:f8:ff:ff/00:00:00:00:00/ef Emask 0x1 (device error)
ata1.00: status: { DRDY ERR }
ata1.00: error: { ABRT }
ata1.00: configured for UDMA/33
ata1: EH complete
...
After some investigations, it turned out this seems to be caused
by misinterpretation of the ATA specification on LBA28 access.
Following part is the code in question:
HGST drive (sometimes) fails with LBA28 access of {block = 0xfffffff,
n_block = 1}, and this behavior seems to be comformant. Other drives,
including other HGST drives are not that strict, through.
>From the ATA specification:
(http://www.t13.org/Documents/UploadedDocuments/project/d1410r3b-ATA-ATAPI-6.pdf)
8.15.29 Word (61:60): Total number of user addressable sectors
This field contains a value that is one greater than the total number
of user addressable sectors (see 6.2). The maximum value that shall
be placed in this field is 0FFFFFFFh.
So the driver shouldn't use the value of 0xfffffff for LBA28 request
as this exceeds maximum user addressable sector. The logical maximum
value for LBA28 is 0xffffffe.
The obvious fix is to cut "- 1" part, and the patch attached just do
that. I've been using the patched kernel for about a month now, and
the same fix is also floating on the net for some time. So I believe
this fix works reliably.
Just FYI, many Windows/Intel platform users also seems to be struck
by this, and HGST has issued a note pointing to Intel ICH8/9 driver.
Russell King [Sat, 13 Sep 2008 20:23:06 +0000 (21:23 +0100)]
[ARM] Fix PCI_DMA_BUS_IS_PHYS for ARM
PCI_DMA_BUS_IS_PHYS was defined to be zero, which meant we ignored
the DMA mask for IDE and SCSI transfers. This is wrong - we have
no DMA translation hardware. We want to obey DMA masks so that the
block layer performs bouncing itself.
Reported-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com> Acked-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ARM] 5246/1: tosa: add proper clock alias for tc6393xb clock
Add clock alias for clock that is used by tc6393xb device on tosa.
As that chip plays pretty major part in tosa life and is currently
disabled, this is 2.4.27 material.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Santwona Behera [Fri, 12 Sep 2008 23:04:26 +0000 (16:04 -0700)]
niu: panic on reset
The reset_task function in the niu driver does not reset the tx and rx
buffers properly. This leads to panic on reset. This patch is a
modified implementation of the previously posted fix.
Signed-off-by: Santwona Behera <santwona.behera@sun.com> Signed-off-by: David S. Miller <davem@davemloft.net>
/**
* nla_ok - check if the netlink attribute fits into the remaining bytes
* @nla: netlink attribute
* @remaining: number of bytes remaining in attribute stream
*/
static inline int nla_ok(const struct nlattr *nla, int remaining)
{
return remaining >= sizeof(*nla) &&
nla->nla_len >= sizeof(*nla) &&
nla->nla_len <= remaining;
}
It turns out that remaining can become negative due to alignment in
nla_next(). But GCC promotes "remaining" to unsigned in the test
against sizeof(*nla) above. Therefore the test succeeds, and the
nla_for_each_attr() may access memory outside the received buffer.
A short example illustrating this point is here:
#include <stdio.h>
main(void)
{
printf("%d\n", -1 >= sizeof(int));
}
...which prints "1".
This patch adds a cast in front of the sizeof so that GCC will make
a signed comparison and fix the illegal memory dereference. With the
patch applied, there is no kmemcheck report.
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com> Acked-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
[Bluetooth] Fix regression from using default link policy
To speed up the Simple Pairing connection setup, the support for the
default link policy has been enabled. This is in contrast to settings
the link policy on every connection setup. Using the default link policy
is the preferred way since there is no need to dynamically change it for
every connection.
For backward compatibility reason and to support old userspace the
HCISETLINKPOL ioctl has been switched over to using hci_request() to
issue the HCI command for setting the default link policy instead of
just storing it in the HCI device structure.
However the hci_request() can only be issued when the device is
brought up. If used on a device that is registered, but still down
it will timeout and fail. This is problematic since the command is
put on the TX queue and the Bluetooth core tries to submit it to
hardware that is not ready yet. The timeout for these requests is
10 seconds and this causes a significant regression when setting up
a new device.
The userspace can perfectly handle a failure of the HCISETLINKPOL
ioctl and will re-submit it later, but the 10 seconds delay causes
a problem. So in case hci_request() is called on a device that is
still down, just fail it with ENETDOWN to indicate what happens.
David Howells [Thu, 11 Sep 2008 16:18:56 +0000 (17:18 +0100)]
MN10300: Change the fault handler to check in_atomic() not in_interrupt()
Change the MN10300 fault handler to make it check in_atomic() rather than
in_interrupt() as commit 6edaf68a87d17570790fd55f0c451a29ec1d6703 did for other
architectures:
Author: Peter Zijlstra <a.p.zijlstra@chello.nl>
Date: Wed Dec 6 20:32:18 2006 -0800
[PATCH] mm: arch do_page_fault() vs in_atomic()
In light of the recent pagefault and filemap_copy_from_user work I've
gone through all the arch pagefault handlers to make sure the
inc_preempt_count() 'feature' works as expected.
Several sections of code (including the new filemap_copy_from_user)
rely on the fact that faults do not take locks under increased preempt
count.
Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The callers of sg_copy_buffer must disable interrupts before calling
it (since it uses kmap_atomic). Some callers use it on
interrupt-disabled code but some need to take the trouble to disable
interrupts just for this. No wonder they forget about it and we hit a
bug like:
http://bugzilla.kernel.org/show_bug.cgi?id=11529
James said that it might be better to disable interrupts inside the
function rather than risk the callers getting it wrong.
Merge branch 'kvm-updates/2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm
* 'kvm-updates/2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
KVM: VMX: Always return old for clear_flush_young() when using EPT
KVM: SVM: fix guest global tlb flushes with NPT
KVM: SVM: fix random segfaults with NPT enabled
Jouni Malinen [Mon, 11 Aug 2008 11:01:50 +0000 (14:01 +0300)]
ath9k: Assign seq# when mac80211 requests this
Use TX control flag IEEE80211_TX_CTL_ASSIGN_SEQ as a request to update
the seq# for the frames. This will likely require some further cleanup
to get seq# correctly for Beacons vs. other frames and also potentially
for multiple BSSes. Anyway, this is better than ending up sending out
most frames with seq# 0.
(This is a backport of patch w/ same title already in net-next-2.6.
It is verified to fix http://bugzilla.kernel.org/show_bug.cgi?id=11394
and it should be acceptable for -rc due to the driver being new
in 2.6.27.)
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
block: disable sysfs parts of the disk command filter
We still have life time issues with the sysfs command filter kobject,
so disable it for 2.6.27 release. We can revisit this and make it work
properly for 2.6.28, for 2.6.27 release it's too risky.
Russell King [Tue, 9 Sep 2008 09:16:22 +0000 (10:16 +0100)]
[ARM] OMAP: Fix MMC device data
OMAPs MMC device data was passing the wrong structure via the platform
device. Moreover, a missing function means that both sx1_defconfig
and omap_h2_1610_defconfig builds failed with
undefined reference to `omap_set_mmc_info'
errors. Fix this by updating the MMC support from the omapzoom tree.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Accesses to CR4 are intercepted even with Nested Paging enabled. But the code
does not check if the guest wants to do a global TLB flush. So this flush gets
lost. This patch adds the check and the flush to svm_set_cr4.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
Joerg Roedel [Wed, 27 Aug 2008 12:18:43 +0000 (14:18 +0200)]
KVM: SVM: fix random segfaults with NPT enabled
This patch introduces a guest TLB flush on every NPF exit in KVM. This fixes
random segfaults and #UD exceptions in the guest seen under some workloads
(e.g. long running compile workloads or tbench). A kernbench run with and
without that fix showed that it has a slowdown lower than 0.5%
Cc: stable@kernel.org Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Alexander Graf <agraf@suse.de> Signed-off-by: Avi Kivity <avi@qumranet.com>
commit 0d3244d6439c8c31d2a29efd587c7aca9042c8aa ("V4L/DVB (8342):
sh_mobile_ceu_camera: Add SuperH Mobile CEU driver V3") introduced
VIDEO_SH_MOBILE_CEU, which selects VIDEOBUF_DMA_CONTIG. This circumvents the
dependency on HAS_DMA of VIDEOBUF_DMA_CONTIG.
Add a dependency on HAS_DMA to VIDEO_SH_MOBILE_CEU to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Paul Mundt <lethal@linux-sh.org> Acked-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
swiotlb: fix back-off path when memory allocation fails
This fixes a SWIOTLB oops
With SWIOTLB being enabled and straight-forward page allocation
failure [1], the swiotlb_alloc_coherent fall-back path hits an
issue [2], resulting in my webcam failing to work.
At the time of oops, RDI is clearly a pointer to a structure which
has arrived as NULL, leading to the typo in swiotlb_map_single's
callsite arguments.
Correctly passing the device structure [3] addresses the issue and
gets my webcam working again (the allocation failure still occuring).
ide: Fix pointer arithmetic in hpt3xx driver code (3rd try)
git commit 74811f355f4f69a187fa74892dcf2a684b84ce99 causes crash at
module load (or boot) time on my machine with a hpt374 controller.
The reason for this is that for initializing second controller which sets
(hwif->dev == host->dev[1]) to true (1), adds 1 to a void ptr, which
advances it by one byte instead of advancing it by sizeof(hpt_info) bytes.
Because of this, all initialization functions get corrupted data in info
variable which causes a crash at boot time.
This patch fixes that and makes my machine boot again.
The card itself is a HPT374 raid conroller: Here is the lspci -v output:
03:06.0 RAID bus controller: HighPoint Technologies, Inc. HPT374 (rev
07)
Subsystem: HighPoint Technologies, Inc. Unknown device 0001
Flags: bus master, 66MHz, medium devsel, latency 120, IRQ 28
I/O ports at 8000 [size=8]
I/O ports at 7800 [size=4]
I/O ports at 7400 [size=8]
I/O ports at 7000 [size=4]
I/O ports at 6800 [size=256]
Expansion ROM at fe8e0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
03:06.1 RAID bus controller: HighPoint Technologies, Inc. HPT374 (rev
07)
Subsystem: HighPoint Technologies, Inc. Unknown device 0001
Flags: bus master, 66MHz, medium devsel, latency 120, IRQ 28
I/O ports at 9800 [size=8]
I/O ports at 9400 [size=4]
I/O ports at 9000 [size=8]
I/O ports at 8800 [size=4]
I/O ports at 8400 [size=256]
Capabilities: [60] Power Management version 2
Signed-off-by: Masoud Sharbiani <masouds@google.com> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Andrew Morton <akpm@linux-foundation.org>
[bart: use dev_get_drvdata() per Sergei's suggestion] Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Paul E. McKenney [Sun, 31 Aug 2008 18:06:30 +0000 (11:06 -0700)]
[IA64] prevent ia64 from invoking irq handlers on offline CPUs
Make ia64 refrain from clearing a given to-be-offlined CPU's bit in the
cpu_online_mask until it has processed pending irqs. This change
prevents other CPUs from being blindsided by an apparently offline CPU
nevertheless changing globally visible state. Also remove the existing
redundant cpu_clear(cpu, cpu_online_map).
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
Robin Holt [Tue, 9 Sep 2008 15:34:44 +0000 (10:34 -0500)]
[IA64] fix up bte.h
bte.h expects a #define of L1_CACHE_MASK which is currently only
in bte.c. This small patch gets bte.h to include cleanly and makes
BTE_UNALIGNED_COPY not report errors.
Signed-off-by: Robin Holt <holt@sgi.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
projects / linux-2.6 / log