Randy Vinson [Tue, 17 Jul 2007 23:37:12 +0000 (16:37 -0700)]
[POWERPC] 85xxCDS: MPC8548 DTS cleanup.
Added the P2P bridge present on the Arcadia base board and moved the VIA
Southbridge behind the bridge to reflect its actual position in the bus
organization. Added the RTC that's in the VIA Southbridge and expanded
the ranges array for the SOC node to allow proper address translation of
the RTC registers.
Signed-off-by: Randy Vinson <rvinson@mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Randy Vinson [Thu, 14 Jun 2007 18:02:54 +0000 (11:02 -0700)]
[POWERPC] 85xxCDS: Delay 8259 cascade hookup.
The interrupts of an E100 card inserted in PCI slot 4 may be on at bootup.
The resulting interrupt flood interacts with the 8259 cascade handler and
prevents proper boot up. There is a quirk for the E100 that will disable
the E100's interrupts but to use it, the 8259 cascade hookup must be
delayed until after the quirk has run. This patch delays the 8259 cascade
hookup by registering a device_initcall() which runs after the PCI quirk
for the E100.
Signed-off-by: Randy Vinson <rvinson@mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Randy Vinson [Fri, 23 Mar 2007 22:43:37 +0000 (15:43 -0700)]
[POWERPC] 85xxCDS: Make sure restart resets the PCI bus.
The current 85xxCDS restart code fails to reset the PCI bus which can
lead to odd behavior after the restart. This patch uses the VIA Super
Southbridge to perform a PCI reset which will reset the entire system.
NOTE: Since the VIA chip is behind a PCI-to-PCI bridge which can be
disabled with a switch setting, it may not be possible to perform the
PCI bus reset. In this case, the code defaults to the previous restart
mechanism.
Signed-off-by: Randy Vinson <rvinson@mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Randy Vinson [Wed, 6 Jun 2007 23:26:15 +0000 (16:26 -0700)]
[POWERPC] 85xxCDS: Allow 8259 cascade to share an MPIC interrupt line.
The Freescale MPC8555CDS and MPC8548CDS reference hardware has a legacy
8259 interrupt controller pair contained within a VIA VT82C686B Southbridge
on the main carrier board. The processor complex plugs into the carrier
card using a PCI slot which limits the available interrupts to the
INTA-INTD PCI interrupts. The output of the 8259 cascade pair is routed
through a gate array and connected to the PCI INTA interrupt line.
The normal interrupt chaining hook (set_irq_chained_handler) does
not allow sharing of the chained interrupt which prevents the
use of PCI INTA by PCI devices. This patch allows the 8259 cascade
pair to share their interrupt line with PCI devices.
NOTE: The addition of the .end routine for the MPIC is not strictly
necessary for this patch. It's there so this code will run from within
the threaded interrupt context used by the Real Time patch.
Signed-off-by: Randy Vinson <rvinson@mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 20 Jul 2007 18:49:29 +0000 (13:49 -0500)]
[POWERPC] Make sure virtual P2P bridge registers are setup on PCIe PHB
For the Freescale PCIe PHBs Not all firmwares setup the virtual P2P
bridge registers properly. Make sure they get setup based on what
the struct pci_controller got from the device tree.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 20 Jul 2007 18:35:34 +0000 (13:35 -0500)]
[POWERPC] Provide ability to setup P2P bridge registers from struct resource
We need the ability to set P2P bridge registers to properly setup the virtual
P2P bridges that exist in PCIe controllers for some of the embedded setups.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Roy Zang [Fri, 13 Jul 2007 10:05:08 +0000 (18:05 +0800)]
[POWERPC] Add basic PCI/PCI Express support for 8544DS board
Add basic support for the PCIe PHB and enable the ULI bridge.
Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 19 Jul 2007 21:07:35 +0000 (16:07 -0500)]
[POWERPC] Make endianess of cfg_addr for indirect pci ops runtime
Make it so we do a runtime check to know if we need to write cfg_addr
as big or little endian. This is needed if we want to allow 86xx support
to co-exist in the same kernel as other 6xx PPCs.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 19 Jul 2007 20:29:53 +0000 (15:29 -0500)]
[POWERPC] Fixup resources on pci_bus for PCIe PHB when no device is connected
On the 85xx/86xx PCIe controllers if there is no device connected to the
PHB we will still allocate a pci_bus for downstream bus of the virtual
P2P bridge. However the resources allocated to the downstream bus are not
correct and so we just mimic the resources from the upstream pci_bus.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 11 Jul 2007 18:31:58 +0000 (13:31 -0500)]
[POWERPC] FSL: Cleanup how we detect if we are a PCIe controller
Use the PCI capabilities to determine if we are PCIe PHB. Also use
PPC_INDIRECT_TYPE_NO_PCIE_LINK since the Freescale PCIe controllers
will lock the system if they don't have link and you try to do a config
access to anything but the PHB.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 11 Jul 2007 18:22:41 +0000 (13:22 -0500)]
[POWERPC] Added indirect quirk to handle PCIe PHB that have issue w/no link
Added PPC_INDIRECT_TYPE_NO_PCIE_LINK flag to the indirect pci handling
code to ensure that we don't talk to any device other than the PHB
if we don't have PCIe link. Some controllers will lockup if they try
to do a config cycle to any device on the bus except the PHB.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 11 Jul 2007 04:37:45 +0000 (23:37 -0500)]
[POWERPC] Add the ability to find PCI capabilities early on
Added early_find_capability that wraps pci_bus_find_capability and uses
fake_pci_bus() to allow us to call it before we've fully setup the
pci_controller.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Roy Zang [Tue, 10 Jul 2007 10:44:34 +0000 (18:44 +0800)]
[POWERPC] Create common fsl pci/e files based on 86xx platforms
Move
arch/powerpc/platforms/86xx/pci.c -> arch/powerpc/sysdev/fsl_pci.c
arch/powerpc/sysdev/fsl_pcie.h -> arch/powerpc/sysdev/fsl_pci.h
as the base to unify 83xx/85xx/86xx pci and pcie.
Add CONFIG_FSL_PCI to build fsl_pci.c for Freescale pci and pcie option.
The code still works for 86xx platforms.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The recent 9p commit: bd238fb431f31989898423c8b6496bc8c4204a86 that
supposedly only moved files also introduced a new 9p sysctl interface
that did not properly register it's sysctl binary numbers.
And since it was only for debugging clearly did not need a binary fast
path in any case. So this patch just remove the binary numbers.
See Documentation/sysctl/ctl_unnumbered.txt for more details.
While I was at it I cleaned up the sysctl initializers a little as
well so there is less to read.
Cc: Latchesar Ionkov <lucho@ionkov.net> Cc: Eric Van Hensbergen <ericvh@gmail.com> Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Support small QP queues
IB/ehca: Make internal_create/destroy_qp() static
IB/ehca: Move ehca2ib_return_code() out of line
IB/ehca: Generate async event when SRQ limit reached
IB/ehca: Support large page MRs
IB/mlx4: Fix error path in create_qp_common()
mlx4_core: Change command token on timeout
IB/mthca: Change command token on timeout
IB/ipath: Remove ipath_layer dead code
IB/mlx4: Fix leaks in __mlx4_ib_modify_qp
Al Viro [Sat, 21 Jul 2007 22:29:12 +0000 (23:29 +0100)]
take declarations of enable_irq() et.al. to linux/interrupt.h
Now that the last inlined instances are gone, all that is left to do
is turning disable_irq_nosync on arm26 and m68k from defines to aliases
and we are all set - we can make these externs in linux/interrupt.h
uncoditional and kill remaining instances in asm/irq.h
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
James Bottomley [Sun, 22 Jul 2007 18:15:55 +0000 (13:15 -0500)]
[SCSI] libsas: make ATA functions selectable by a config option
Not everyone wants libsas automatically to pull in libata. This patch
makes the behaviour configurable, so you can build libsas with or
without ATA support.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Merge branch 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: Convert from struct class_device to struct device
leds: leds-gpio for ngw100
leds: Add warning printks in error paths
leds: Fix trigger unregister_simple if register_simple fails
leds: Use menuconfig objects II - LED
leds: Teach leds-gpio to handle timer-unsafe GPIOs
leds: Add generic GPIO LED driver
Merge branch 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
leds: cr_bllcd.c: build fix
backlight: Convert from struct class_device to struct device
backlight: Fix order of Kconfig entries
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Clean up duplicate includes in drivers/macintosh/
[POWERPC] Quiet section mismatch warning on pcibios_setup
[POWERPC] init and exit markings for hvc_iseries
[POWERPC] Quiet section mismatch in hvc_rtas.c
[POWERPC] Constify of_platform_driver match_table
[POWERPC] hvcs: Make some things static and const
[POWERPC] Constify of_platform_driver name
[POWERPC] MPIC protected sources
[POWERPC] of_detach_node()'s device node argument cannot be const
[POWERPC] Fix ARCH=ppc builds
[POWERPC] mv64x60: Use mutex instead of semaphore
[POWERPC] Allow smp_call_function_single() to current cpu
[POWERPC] Allow exec faults on readable areas on classic 32-bit PowerPC
[POWERPC] Fix future firmware feature fixups function failure
[POWERPC] fix showing xmon help
[POWERPC] Make xmon_write accept a const buffer
[POWERPC] Fix misspelled "CONFIG_CHECK_CACHE_COHERENCY" Kconfig option.
[POWERPC] cell: CONFIG_SPE_BASE is a typo
Al Viro [Sun, 22 Jul 2007 09:59:06 +0000 (10:59 +0100)]
fix broken handling of port=... in NFS option parsing
Obviously broken on little-endian; fortunately, the option is not
frequently used...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[ Hey, sparse is wonderful, but even better than sparse is having people
like Al that actually _run_ it and fix bugs using it. - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (77 commits)
ACPI: Populate /sys/firmware/acpi/tables/
ACPI: create CONFIG_ACPI_DEBUG_FUNC_TRACE
ACPI: update ACPI proc I/F removal schedule
ACPI: update feature-removal-schedule.txt, /sys/firmware/acpi/namespace is gone
ACPI: export ACPI events via acpi_mc_group multicast group
ACPI: fix empty macros found by -Wextra
ACPI: drivers/acpi/pci_link.c: lower printk severity
sony-laptop: Fix event reading in sony-laptop
sony-laptop: Add Vaio FE to the special init sequence
sony-laptop: Make the driver use MSC_SCAN and a setkeycode and getkeycode key table.
sony-laptop: Invoke _INI for SNC devices that provide it
sony-laptop: Add support for recent Vaios Fn keys (C series for now)
sony-laptop: map wireless switch events to KEY_WLAN
sony-laptop: add new SNC handlers
ACPI: thinkpad-acpi: add locking to brightness subdriver
ACPI: thinkpad-acpi: bump up version to 0.15
ACPI: thinkpad-acpi: make EC-based thermal readings non-experimental
ACPI: thinkpad-acpi: make sure DSDT TMPx readings don't return +128
ACPI: thinkpad-acpi: react to Lenovo ThinkPad differences in hot key
ACPI: thinkpad-acpi: allow use of CMOS NVRAM for brightness control
...
Sam Ravnborg [Sun, 22 Jul 2007 09:12:44 +0000 (11:12 +0200)]
x86_64: fix section mismatch warning in init.c
Fix following warning:
WARNING: vmlinux.o(.text+0x188ea): Section mismatch: reference to .init.text:__alloc_bootmem_core (between 'alloc_bootmem_high_node' and 'get_gate_vma')
alloc_bootmem_high_node() is only used from __init scope so declare it __init.
And in addition declare the weak variant __init too.
Sam Ravnborg [Sun, 22 Jul 2007 09:12:42 +0000 (11:12 +0200)]
x86_64: fix section mismatch warning in hpet.c
Fix following warnings:
WARNING: vmlinux.o(.text+0x945e): Section mismatch: reference to .init.text:__set_fixmap (between 'hpet_arch_init' and 'hpet_mask_rtc_irq_bit')
WARNING: vmlinux.o(.text+0x9474): Section mismatch: reference to .init.text:__set_fixmap (between 'hpet_arch_init' and 'hpet_mask_rtc_irq_bit')
hpet_arch_init is only used from __init context so mark it __init.
x86: Replace NSC/Cyrix specific chipset access macros by inlined functions.
Due to index register access ordering problems, when using macros a line
like this fails (and does nothing):
setCx86(CX86_CCR2, getCx86(CX86_CCR2) | 0x88);
With inlined functions this line will work as expected.
Note about a side effect: Seems on Geode GX1 based systems the
"suspend on halt power saving feature" was never enabled due to this
wrong macro expansion. With inlined functions it will be enabled, but
this will stop the TSC when the CPU runs into a HLT instruction.
Kernel output something like this:
Clocksource tsc unstable (delta = -472746897 ns)
This is the 3rd version of this patch.
- Adding missed arch/i386/kernel/cpu/mtrr/state.c
Thanks to Andres Salomon
- Adding some big fat comments into the new header file
Suggested by Andi Kleen
Keith Owens [Sun, 22 Jul 2007 09:12:36 +0000 (11:12 +0200)]
i386: Do not include other cpus' interrupt 0 in nmi_watchdog
kstat_irqs(0) includes the count of interrupt 0 from all cpus, not just
the current cpu. The updated interrupt 0 on other cpus can stop the
nmi_watchdog from tripping, so only include the current cpu's int 0.
When a machine check or NMI occurs while multiple byte code is patched
the CPU could theoretically see an inconsistent instruction and crash.
Prevent this by temporarily disabling MCEs and returning early in the
NMI handler.
x86: Fix alternatives and kprobes to remap write-protected kernel text
Reenable kprobes and alternative patching when the kernel text is write
protected by DEBUG_RODATA
Add a general utility function to change write protected text. The new
function remaps the code using vmap to write it and takes care of CPU
synchronization. It also does CLFLUSH to make icache recovery faster.
There are some limitations on when the function can be used, see the
comment.
This is a newer version that also changes the paravirt_ops code.
text_poke also supports multi byte patching now.
Contains bug fixes from Zach Amsden and suggestions from Mathieu
Desnoyers.
This patch uses the read and write functions provided at system.h
for control registers instead of writting raw assembly over and
over again in .c files. Functions to manipulate cr2 and cr8 were
provided, as they were lacking.
Also, removed some extra space after closing brackets
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com> Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch makes the i386 behave the same way that x86_64 does when a
segfault happens. A line gets printed to the kernel log so that tools
that need to check for failures can behave more uniformly between
debug.show_unhandled_signals sysctl variable to 0 (or by doing echo 0 >
/proc/sys/debug/exception-trace)
Also, all of the lines being printed are now using printk_ratelimit() to
deny the ability of DoS from a local user with a program like the
following:
main()
{
while (1)
if (!fork()) *(int *)0 = 0;
}
This new revision also includes the fix that Andrew did which got rid of
new sysctl that was added to the system in earlier versions of this.
Also, 'show-unhandled-signals' sysctl has been renamed back to the old
'exception-trace' to avoid breakage of people's scripts.
AK: Enabling by default for i386 will be likely controversal, but let's see what happens
AK: Really folks, before complaining just fix your segfaults
AK: I bet this will find a lot of silent issues
Signed-off-by: Masoud Sharbiani <masouds@google.com> Signed-off-by: Andi Kleen <ak@suse.de>
[ Personally, I've found the complaints useful on x86-64, so I'm all for
this. That said, I wonder if we could do it more prettily.. -Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Sun, 22 Jul 2007 07:10:35 +0000 (08:10 +0100)]
Fix ppc64 mismerge
Fix a mismerge in commit 8b6f50ef1d5cc86b278eb42bc91630fad455fb10:
"spufs: make signal-notification files readonly for NOSCHED contexts",
where structs got duplicated.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Acked-by: Jeremy Kerr <jk@ozlabs.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Dooks [Sun, 22 Jul 2007 15:23:02 +0000 (16:23 +0100)]
[ARM] 4524/1: S3C: Move register out of include/asm-arm/arch-s3c2410
Move register and other definitions out of the
include/asm-arm/arch-s3c2410 into the the arch
directories of include/asm-arm/plat-s3c24xx and
include/asm-arm/plat-s3c.
This move is in preperation of the merging of
s3c2400 and s3c6400.
The following git mv commands are needed before
this patch can be applied:
Ben Dooks [Sun, 22 Jul 2007 15:59:44 +0000 (16:59 +0100)]
[ARM] 4521/2: S3C: Reorganise VA mapping headers
Reorganise the definition of the virtual addresses
used into a common header and update the users to
rename S3C2410 items into a more common S3C defined
macros.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ben Dooks [Sun, 22 Jul 2007 15:18:22 +0000 (16:18 +0100)]
[ARM] 4519/1: S3C: split S3C2400 values out of S3C24XX map.h
Move the S3C2400 values to their own include directory
series in include/asm-arm/arch-s3c2400 as the support
for the S3C2400 is best placed in its own arch directory.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ben Dooks [Sun, 22 Jul 2007 15:15:44 +0000 (16:15 +0100)]
[ARM] 4517/1: S3C: Fix debug macros for ARM926 output
Check for ARM926 based S3C24XX based devices as these
only have 64 byte FIFOs, and do not have the model
detection refisters in the same place as the ARM920
based CPUs
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ben Dooks [Sun, 22 Jul 2007 15:12:04 +0000 (16:12 +0100)]
[ARM] 4514/1: S3C: Rename DEBUG_S3C2410_PORT and DEBUG_S3C_UART
Rename DEBUG_S3C2410_PORT to DEBUG_S3C_PORT as well as
DEBUG_S3C2410_UART to DEBUG_S3C_UART as part of the updates
to moving to plat-s3c for S3C base support.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ben Dooks [Sun, 22 Jul 2007 15:09:44 +0000 (16:09 +0100)]
[ARM] 4511/1: S3C: updated LLSERIAL Kconfig defines for CPU support
Update the Kconfig to create configuration options based on which
CPUs are supported for the low level serial code. This means that
the debug macros can be optimised for the type(s) of CPU that are
being used.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Create the initial arch/arm/plat-s3c directory and start
linking it into the arch/arm build heirarchy ready to
receive the generic parts of the S3C24XX support to be
used when adding S3C6400 devices.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ben Dooks [Sun, 22 Jul 2007 15:05:25 +0000 (16:05 +0100)]
[ARM] 4508/1: S3C: Move items to include/asm-arm/plat-s3c
This patch moves items of the s3c24xx support into
a new plat-s3c directory for items that use the
s3c24xx support but are not directly s3c24xx
compatible, such as the s3c2400 and s3c6400.
[ARM] 4461/1: MXC platform and i.MX31ADS core support
This patch adds the foundation pieces for
the Freescale MXC platforms, including
i.MX2 and i.MX3 based systems.
The bare-bones MX31 support in this patch
boots to the rootdev panic with 8250 serial
console configured "console=ttyS0,115200".
It assumes that Redboot is the boot loader.
Signed-off-by: Quinn Jensen <quinn.jensen@freescale.com> Acked-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Al Viro [Thu, 7 Jun 2007 15:13:31 +0000 (11:13 -0400)]
[PATCH] get rid of AVC_PATH postponed treatment
Selinux folks had been complaining about the lack of AVC_PATH
records when audit is disabled. I must admit my stupidity - I assumed
that avc_audit() really couldn't use audit_log_d_path() because of
deadlocks (== could be called with dcache_lock or vfsmount_lock held).
Shouldn't have made that assumption - it never gets called that way.
It _is_ called under spinlocks, but not those.
Since audit_log_d_path() uses ab->gfp_mask for allocations,
kmalloc() in there is not a problem. IOW, the simple fix is sufficient:
let's rip AUDIT_AVC_PATH out and simply generate pathname as part of main
record. It's trivial to do.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Acked-by: James Morris <jmorris@namei.org>
The sanity check in audit_match_class() is wrong. We are able to audit
2048 syscalls but in audit_match_class() we were accidentally using
sizeof(_u32) instead of number of bits in _u32 when deciding how many
syscalls were valid. On ia64 in particular we were hitting syscall
numbers over the (wrong) limit of 256. Fixing the audit_match_class
check takes care of the problem.
Signed-off-by: Klaus Weidner <klaus@atsec.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Stephen Rothwell [Sat, 21 Jul 2007 14:27:01 +0000 (00:27 +1000)]
[POWERPC] Constify of_platform_driver match_table
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Mackerras <paulus@samba.org>
Stephen Rothwell [Sat, 21 Jul 2007 14:23:03 +0000 (00:23 +1000)]
[POWERPC] Constify of_platform_driver name
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Mackerras <paulus@samba.org>
Some HW platforms, such as the new cell blades, requires some MPIC sources
to be left alone by the operating system. This implements support for
a "protected-sources" property in the mpic controller node containing a list
of source numbers to be protected against operating system interference.
For those interested in the gory details, the MPIC on the southbridge of
those blades has some of the processor outputs routed to the cell, and
at least one routed as a GPIO to the service processor. It will be used
in the GA product for routing some of the southbridge error interrupts
to the service processor which implements some of the RAS stuff, such
as checkstopping when fatal errors occurs before they can propagate.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
The recent signal rework broke ARCH=ppc builds with the following
error:
CC arch/powerpc/kernel/signal.o
arch/powerpc/kernel/signal.c: In function Â\91do_signalÂ\92:
arch/powerpc/kernel/signal.c:142: error: implicit declaration of
function Â\91set_dabrÂ\92
make[1]: *** [arch/powerpc/kernel/signal.o] Error 1
This fixes it by including a function prototype in asm-ppc/system.h.
Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
projects / linux-2.6 / log