David Fries [Mon, 18 Aug 2008 04:03:40 +0000 (23:03 -0500)]
x86: fix i486 suspend to disk CR4 oops
arch/x86/power/cpu_32.c __save_processor_state calls read_cr4()
only a i486 CPU doesn't have the CR4 register. Trying to read it
produces an invalid opcode oops during suspend to disk.
Use the safe rc4 reading op instead. If the value to be written is
zero the write is skipped.
arch/x86/power/hibernate_asm_32.S
done: swapped the use of %eax and %ecx to use jecxz for
the zero test and jump over store to %cr4.
restore_image: s/%ecx/%eax/ to be consistent with done:
In addition to __save_processor_state, acpi_save_state_mem,
efi_call_phys_prelog, and efi_call_phys_epilog had checks added
(acpi restore was in assembly and already had a check for
non-zero). There were other reads and writes of CR4, but MCE and
virtualization shouldn't be executed on a i486 anyway.
Signed-off-by: David Fries <david@fries.net> Acked-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Marcin Slusarz [Sun, 10 Aug 2008 22:09:38 +0000 (00:09 +0200)]
x86: mpparse.c: fix section mismatch warning
WARNING: vmlinux.o(.text+0x118f7): Section mismatch in reference from the function construct_ioapic_table() to the function .init.text:MP_bus_info()
The function construct_ioapic_table() references
the function __init MP_bus_info().
This is often because construct_ioapic_table lacks a __init
annotation or the annotation of MP_bus_info is wrong.
construct_ioapic_table is called only from construct_default_ISA_mptable which is __init
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Marcin Slusarz [Sun, 10 Aug 2008 22:11:13 +0000 (00:11 +0200)]
x86: mmconf: fix section mismatch warning
WARNING: arch/x86/kernel/built-in.o(.cpuinit.text+0x1591): Section mismatch in reference from the function init_amd() to the function .init.text:check_enable_amd_mmconf_dmi()
The function __cpuinit init_amd() references
a function __init check_enable_amd_mmconf_dmi().
If check_enable_amd_mmconf_dmi is only used by init_amd then
annotate check_enable_amd_mmconf_dmi with a matching annotation.
check_enable_amd_mmconf_dmi is only called from init_amd which is __cpuinit
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
WARNING: arch/x86/kernel/built-in.o(.cpuinit.text+0x1fe7): Section mismatch in reference from the function MP_processor_info() to the variable .init.data:x86_quirks
The function __cpuinit MP_processor_info() references
a variable __initdata x86_quirks.
If x86_quirks is only used by MP_processor_info then
annotate x86_quirks with a matching annotation.
MP_processor_info uses x86_quirks which is __init and is used only from
smp_read_mpc and construct_default_ISA_mptable which are __init
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Marcin Slusarz [Sun, 10 Aug 2008 22:07:44 +0000 (00:07 +0200)]
x86, tsc: fix section mismatch warning
WARNING: vmlinux.o(.text+0x7950): Section mismatch in reference from the function native_calibrate_tsc() to the function .init.text:tsc_read_refs()
The function native_calibrate_tsc() references
the function __init tsc_read_refs().
This is often because native_calibrate_tsc lacks a __init
annotation or the annotation of tsc_read_refs is wrong.
tsc_read_refs is called from native_calibrate_tsc which is not __init
and native_calibrate_tsc cannot be marked __init
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
x86: correct register constraints for 64-bit atomic operations
x86_64 add/sub atomic ops does not seems to accept integer values bigger
than 32 bits as immediates. Intel's add/sub documentation specifies they
have to be passed as registers.
The only operations in the x86-64 architecture which accept arbitrary
64-bit immediates is "movq" to any register; similarly, the only
operation which accept arbitrary 64-bit displacement is "movabs" to or
from al/ax/eax/rax.
e
32-bit signed integer constant, or a symbolic reference known to fit
that range (for immediate operands in sign-extending x86-64
instructions).
Z
32-bit unsigned integer constant, or a symbolic reference known to
fit that range (for immediate operands in zero-extending x86-64
instructions).
Since add/sub does sign extension, using the "e" constraint seems appropriate.
It applies to 2.6.27-rc, 2.6.26, 2.6.25...
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ingo Molnar [Wed, 13 Aug 2008 16:02:18 +0000 (18:02 +0200)]
x86: add MAP_STACK mmap flag
as per this discussion:
http://lkml.org/lkml/2008/8/12/423
Pardo reported that 64-bit threaded apps, if their stacks exceed the
combined size of ~4GB, slow down drastically in pthread_create() - because
glibc uses MAP_32BIT to allocate the stacks. The use of MAP_32BIT is
a legacy hack - to speed up context switching on certain early model
64-bit P4 CPUs.
So introduce a new flag to be used by glibc instead, to not constrain
64-bit apps like this.
glibc can switch to this new flag straight away - it will be ignored
by the kernel. If those old CPUs ever matter to anyone, support for
it can be implemented.
Marcin Slusarz [Fri, 15 Aug 2008 16:32:24 +0000 (18:32 +0200)]
x86: fix section mismatch warning - spp_getpage()
WARNING: vmlinux.o(.text+0x17a3e): Section mismatch in reference from the function set_pte_vaddr_pud() to the function .init.text:spp_getpage()
The function set_pte_vaddr_pud() references
the function __init spp_getpage().
This is often because set_pte_vaddr_pud lacks a __init
annotation or the annotation of spp_getpage is wrong.
spp_getpage is called from __init (__init_extra_mapping) and
non __init (set_pte_vaddr_pud) functions, so it can't be __init.
Unfortunately it calls alloc_bootmem_pages which is __init,
but does it only when bootmem allocator is available (after_bootmem == 0).
So annotate it accordingly.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Cc: H. Peter Anvin <hpa@zytor.com>
Jens Rottmann [Mon, 4 Aug 2008 12:40:16 +0000 (14:40 +0200)]
x86, geode-mfgpt: check IRQ before using MFGPT as clocksource
Adds a simple IRQ autodetection to the AMD Geode MFGPT driver, and more
importantly, adds some checks, if IRQs can actually be received on the
chosen line. This fixes cases where MFGPT is selected as clocksource
though not producing any ticks, so the kernel simply starves during
boot.
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de> Cc: Andres Salomon <dilinger@debian.org> Cc: linux-geode@bombadil.infradead.org Cc: Jordan Crouse <jordan.crouse@amd.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Hugh Dickins [Fri, 15 Aug 2008 12:58:32 +0000 (13:58 +0100)]
x86: fix /proc/meminfo DirectMap
Do we actually want these DirectMap lines in the x86 /proc/meminfo?
I can see they're interesting to CPA developers and TLB optimizers,
but they don't fit its usual "where has all my memory gone?" usage.
If they are to stay, here are some fixes.
1. On x86_32 without PAE, they're not 2M but 4M pages: no need to
mess with the internal enum, but show the right name to users.
2. Many machines can never show anything but 0 for DirectMap1G,
so suppress that line unless direct_gbpages are really enabled.
3. The unit in /proc/meminfo is kB not number of pages: HugePages
messed that up, but they're an example to regret not to follow.
4. Once we use kB, it's easy to see that 1GB has gone missing (which
explains why CONFIG_CPA_DEBUG=y soon wraps DirectMap2M negative):
because head_64.S's level2_ident_pgt entries were not counted.
My fix is not ideal, but works for more and for less than 1G,
and avoids interfering with early bootup pagetable contortions.
x86: fix readb() et al compile error with gcc-3.2.3
Building 2.6.27-rc1 on x86 with gcc-3.2.3 fails with:
In file included from include/asm/dma.h:12,
from include/linux/bootmem.h:8,
from init/main.c:26:
include/asm/io.h: In function `readb':
include/asm/io.h:32: syntax error before string constant
include/asm/io.h: In function `readw':
include/asm/io.h:33: syntax error before string constant
include/asm/io.h: In function `readl':
include/asm/io.h:34: syntax error before string constant
include/asm/io.h: In function `__readb':
include/asm/io.h:36: syntax error before string constant
include/asm/io.h: In function `__readw':
include/asm/io.h:37: syntax error before string constant
include/asm/io.h: In function `__readl':
include/asm/io.h:38: syntax error before string constant
make[1]: *** [init/main.o] Error 1
make: *** [init] Error 2
Starting with 2.6.27-rc1 readb() et al are generated by a
build_mmio_read() macro, which generates asm() statements with
output register constraints like "=" "q", i.e. as two adjacent
string literals. This doesn't work with gcc-3.2.3.
Fixed by moving the "=" part into the callers' reg parameter
(as suggested by Ingo).
Build and boot-tested with gcc-3.2.3 on 32 and 64-bit x86.
Mark Langsdorf [Thu, 14 Aug 2008 14:11:26 +0000 (09:11 -0500)]
x86: invalidate caches before going into suspend
When a CPU core is shut down, all of its caches need to be flushed
to prevent stale data from causing errors if the core is resumed.
Current Linux suspend code performs an assignment after the flush,
which can add dirty data back to the cache. On some AMD platforms,
additional speculative reads have caused crashes on resume because
of this dirty data.
Relocate the cache flush to be the very last thing done before
halting. Tie into an assembly line so the compile will not
reorder it. Add some documentation explaining what is going
on and why we're doing this.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com> Acked-by: Mark Borden <mark.borden@amd.com> Acked-by: Michael Hohmuth <michael.hohmuth@amd.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Aristeu Rozanski [Thu, 14 Aug 2008 20:32:15 +0000 (16:32 -0400)]
x86, perfctr: don't use CCCR_OVF_PMI1 on Pentium 4Ds
Currently, setup_p4_watchdog() use CCCR_OVF_PMI1 to enable the counter
overflow interrupts to the second logical core. But this bit doesn't work
on Pentium 4 Ds (model 4, stepping 4) and this patch avoids its use on
these processors. Tested on 4 different machines that have this
specific model with success.
Joerg Roedel [Thu, 14 Aug 2008 17:55:18 +0000 (19:55 +0200)]
x86, AMD IOMMU: initialize dma_ops after sysfs registration
If sysfs registration fails all memory used by IOMMU is freed. This
happens after dma_ops initialization and the functions will access the
freed memory then.
Fix this by initializing dma_ops after the sysfs registration.
Dave Jones [Thu, 14 Aug 2008 19:07:03 +0000 (15:07 -0400)]
x86: silence mmconfig printk
There's so much broken mmconfig hardware/bios'es out there,
that classing this as an error seems a little extreme.
Lower its priority to KERN_INFO so that it isn't so noisy
when booting with 'quiet'
Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Darrick J. Wong [Thu, 14 Aug 2008 22:43:33 +0000 (15:43 -0700)]
x86, msr: fix NULL pointer deref due to msr_open on nonexistent CPUs
msr_open tests for someone trying to open a device for a nonexistent CPU.
However, the function always returns 0, not ret like it should, hence
userspace can BUG the kernel trivially. This bug was introduced by the
cdev lock_kernel pushdown patch last May.
The BUG can be reproduced with these commands:
# mknod fubar c 202 8 <-- pick a number less than NR_CPUS that is not
the number of an online CPU
# cat fubar
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Thomas Gleixner [Thu, 14 Aug 2008 10:17:06 +0000 (12:17 +0200)]
x86: hpet: workaround SB700 BIOS
AMD SB700 based systems with spread spectrum enabled use a SMM based
HPET emulation to provide proper frequency setting. The SMM code is
initialized with the first HPET register access and takes some time to
complete. During this time the config register reads 0xffffffff. We
check for max. 1000 loops whether the config register reads a non
0xffffffff value to make sure that HPET is up and running before we go
further. A counting loop is safe, as the HPET access takes thousands
of CPU cycles. On non SB700 based machines this check is only done
once and has no side effects.
Based on a quirk patch from: crane cai <crane.cai@amd.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Yinghai Lu [Thu, 14 Aug 2008 09:16:30 +0000 (02:16 -0700)]
x86: check bigsmp in smp_sanity_check instead of cpu_up
clear bits for cpu nr > 8.
This allows us to boot the full range of possible CPUs that the
supported APIC model will allow. Previously we'd hang or boot up
with less than 8 CPUs.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com> Tested-by: Jeff Chua <jeff.chua.linux@gmail.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Max Krasnyansky [Mon, 11 Aug 2008 21:55:31 +0000 (14:55 -0700)]
x86: resurrect proper handling of maxcpus= kernel option (v2)
For some reason we had two parsers registered for maxcpus=. One in init/main.c
and another in arch/x86/smpboot.c. So I nuked the one in arch/x86.
Also 64-bit kernels used to handle maxcpus= as documented in
Documentation/cpu-hotplug.txt. CPUs with 'id > maxcpus' are initialized
but not booted. 32-bit version for some reason ignored them even though
all the infrastructure for booting them later is there.
In the current mainline both 64 and 32 bit versions are broken.
This patch restores the correct behaviour. I've tested x86_64 version on
4- and 8- way Core2 and 2-way Opteron based machines. Various config
combinations SMP, !SMP, CPU_HOTPLUG, !CPU_HOTPLUG.
Booted with maxcpus=1 and maxcpus=4, etc. Everything is working as expected.
So far we've received two reports from different people confirming that 32-bit
version also works fine, both on dual core laptops and 16way server machines.
[v2: This version fixes visws breakage pointed out by Ingo.]
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (47 commits)
usb: musb: pass configuration specifics via pdata
usb: musb: fix hanging when rmmod gadget driver
USB: Add MUSB and TUSB support
USB: serial: remove CONFIG_USB_DEBUG from sierra and option drivers
USB: Add vendor/product id of ZTE MF628 to option
USB: quirk PLL power down mode
USB: omap_udc: fix compilation with debug enabled
usb: cdc-acm: drain writes on close
usb: cdc-acm: stop dropping tx buffers
usb: cdc-acm: bugfix release()
usb gadget: issue notifications from ACM function
usb gadget: remove needless struct members
USB: sh: r8a66597-hcd: fix disconnect regression
USB: isp1301: fix compilation
USB: fix compiler warning fix
usb-storage: unusual_devs entry for Nokia 5300
USB: cdc-acm.c: Fix compile warnings
USB: BandRich BandLuxe C150/C250 HSPA Data Card Driver
USB: ftdi_sio: add support for PHI Fisco data cable (FT232BM based, VID/PID 0403:e40b)
usb: isp1760: don't be noisy about short packets.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (56 commits)
netns: Fix crash by making igmp per namespace
bnx2x: Version update
bnx2x: Checkpatch compliance
bnx2x: Spelling mistakes
bnx2x: Minor code improvements
bnx2x: Driver info
bnx2x: 1G LED does not turn off
bnx2x: 8073 PHY changes
bnx2x: Change GPIO for any port
bnx2x: Pause settings
bnx2x: Link order with external PHY
bnx2x: No LRO without Rx checksum
bnx2x: Wrong structure size
bnx2x: WoL capability
bnx2x: Clearing MAC addresses filters
bnx2x: Delay in while loops
bnx2x: PBA Table Page Alignment Workaround
bnx2x: Self-test false positive
bnx2x: Memory allocation
bnx2x: HW attention lock
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Handle stack trace attempts before irqstacks are setup.
sparc64: Implement IRQ stacks.
sparc: remove include of linux/of_device.h from asm/of_device.h
sparc64: Fix recursion in stack overflow detection handling.
sparc/drivers: use linux/of_device.h instead of asm/of_device.h
sparc64: Don't MAGIC_SYSRQ ifdef smp_fetch_global_regs and support code.
Felipe Balbi [Mon, 4 Aug 2008 10:53:52 +0000 (13:53 +0300)]
usb: musb: fix hanging when rmmod gadget driver
If we try to modprobe a second gadget driver before
rmmoding the first one, the reference for the first
gadget driver would get NULLed avoiding usb to change
gadget drivers later.
Cc: David Brownell <david-b@pacbell.net> Cc: Tony Lindgren <tony@atomide.com> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: serial: remove CONFIG_USB_DEBUG from sierra and option drivers
These drivers should not be relying on CONFIG_USB_DEBUG. By doing this,
it prevents users of kernels that do not enable this option from
enabling debugging in these drivers, unlike all other usb-serial
drivers.
Oliver Martin [Sat, 9 Aug 2008 02:49:26 +0000 (04:49 +0200)]
USB: Add vendor/product id of ZTE MF628 to option
This adds the vendor and product id (19d2:0015) of the ZTE MF628 HSDPA
modem to the option driver. It still needs a mode switch command issued
beforehand, this is currently handled by a userspace tool.
Signed-off-by: Oliver Martin <oliver.martin@student.tuwien.ac.at> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Libin Yang [Fri, 8 Aug 2008 07:03:31 +0000 (15:03 +0800)]
USB: quirk PLL power down mode
On some AMD 700 series southbridges, ISO OUT transfers (such as audio
playback through speakers) on the USB OHCI controller may be corrupted
when an A-Link express power saving feature is active.
PLL power down mode in conjunction with link power management feature
L1 being enabled is the bad combination ... this patch prevents them
from being enabled when ISO transfers are pending.
Signed-off-by: Crane Cai <crane.cai@amd.com> Signed-off-by: Libin Yang <libin.yang@amd.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Thu, 7 Aug 2008 01:46:10 +0000 (18:46 -0700)]
usb: cdc-acm: drain writes on close
Add a mechanism to let the write queue drain naturally before
closing the TTY, rather than always losing that data. There
is a timeout, so it can't wait too long.
Provide missing locking inside acm_wb_is_avail(); it matters
more now. Note, this presumes an earlier patch was applied,
removing a call to this routine where the lock was held.
Slightly improved diagnostics on write URB completion, so we
can tell when a write URB gets killed and, if so, how much
data it wrote first ... and so that I/O path is normally
silent (and can't much change timings).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Thu, 7 Aug 2008 01:44:12 +0000 (18:44 -0700)]
usb: cdc-acm: stop dropping tx buffers
The "increase cdc-acm write throughput" patch left in place two
now-obsolete mechanisms, either of which can make the cdc-acm
driver drop TX data (nasty!). This patch removes them:
- The write_ready flag ... if an URB and buffer were found,
they can (and should!) always be used.
- TX path acm_wb_is_used() ... used when the buffer was just
allocated, so that check is pointless.
Also fix a won't-yet-matter leak of a write buffer on a disconnect path.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: David Engraf <david.engraf@netcom.eu> Acked-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Thu, 7 Aug 2008 01:49:57 +0000 (18:49 -0700)]
usb gadget: issue notifications from ACM function
Update the CDC-ACM gadget code to support the peripheral-to-host
notifications when the tty is opened or closed, or issues a BREAK.
The serial framework code calls new generic hooks; right now only
CDC-ACM uses those hooks. This resolves several REVISIT comments
in the code. (Based on a patch from Felipe Balbi.)
Note that this doesn't expose USB_CDC_CAP_BRK to the host, since
this code still rejects USB_CDC_REQ_SEND_BREAK control requests
for host-to-peripheral BREAK signaling (received via /dev/ttyGS*).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Thu, 7 Aug 2008 17:02:40 +0000 (13:02 -0400)]
usb-storage: unusual_devs entry for Nokia 5300
This patch (as1120) adds an unusual_devs entry for the Nokia 5300.
Maybe once Nokia releases the Symbian code we'll be able to fix all
the problems it has with the USB mass-storage protocol.
CC [M] drivers/usb/class/cdc-acm.o
drivers/usb/class/cdc-acm.c: In function 'acm_waker':
drivers/usb/class/cdc-acm.c:527: warning: comparison of distinct pointer types lacks a cast
drivers/usb/class/cdc-acm.c:529: warning: comparison of distinct pointer types lacks a cast
Lex Ross [Wed, 6 Aug 2008 12:25:08 +0000 (16:25 +0400)]
USB: ftdi_sio: add support for PHI Fisco data cable (FT232BM based, VID/PID 0403:e40b)
Support for PHI Fisco USB to Serial data cable (FTDI FT232BM based).
PHI Fisco cable is supplied for connecting Philips Xenium 9@9++ mobile phones.
PIDs were missing.
Tested successfully with PHI Fisco Data Cable (VID/PID 0403:e40b)
Signed-off-by: Lex V. Ross <lross@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to Alan Stern, short packets are quite normal under
certain circumstances. This printk was triggered by usb to
serial converters on every packet and some usb sticks triggered
a few of those while plugging the stick.
This printks are now hidden unless USB debug mode is activated.
Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ISP1760 requires a delay of 90ns between programming the address and
reading the data. Current driver solves this by a mdelay(1) which is
very heavy weighted and slow. This patch applies the workaround from
the ISP1760 FAQ by using two different banks for PTD and payload data
and using a common wait for them. This wait is done by an additional
ISP1760 access (whose timing constraints guarantee the 90ns delay).
This improves speed when reading from an USB stick from:
$ time dd if=/dev/sda of=/dev/zero bs=65536 count=1638
real 1m 15.43s
user 0m 0.44s
sys 0m 39.46s
to
$ time dd if=/dev/sda of=/dev/zero bs=65536 count=1638
real 0m 18.53s
user 0m 0.16s
sys 0m 12.97s
[bigeasy@linutronix.de: fixed comment formating, moved define into
header file, obey 80 char rule]
usb: return error code instead of 0 in the enqueue function.
if the enqueue function returns -ESHUTDOWN or -ENOMEM then
we return 0 instead of an error. This leads to a timeout and
then to a dequeue request of an not enqueued urb.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Mon, 7 Jul 2008 19:16:08 +0000 (12:16 -0700)]
USB: serial gadget: rx path data loss fixes
Update RX path handling in new serial gadget code to cope better with
RX blockage: queue every RX packet until its contents can safely be
passed up to the ldisc. Most of the RX path work is now done in the
RX tasklet, instead of just the final "push to ldisc" step. This
addresses some cases of data loss:
- A longstanding serial gadget bug: when tty_insert_flip_string()
didn't copy the entire buffer, the rest of the characters were
dropped! Now that packet stays queued until the rest of its data
is pushed to the ldisc.
- Another longstanding issue: in the unlikely case that an RX
transfer returns data and also reports a fault, that data is
no longer discarded.
- In the recently added RX throttling logic: it needs to stop
pushing data into the TTY layer, instead of just not submitting
new USB read requests. When the TTY is throttled long enough,
backpressure will eventually make the OUT endpoint NAK.
Also: an #ifdef is removed (no longer necessary); and start switching
to a better convention for debug messages (prefix them with tty name).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kevin Lloyd [Thu, 10 Jul 2008 21:14:57 +0000 (14:14 -0700)]
USB Storage Sierra: TRU-Install feature update
This patch upgrades the support for the Sierra Wireless TRU-Install
feature (i.e. zeroCD) to allow for future support of Linux enabled
TRU-Install devices.
By default all devices that do not have a Linux enabled TRU-Install
device (i.e. the device does not have a Linux package on the virtual CD
partition) will be switched into "modem mode." Devices that do contain a
Linux package in the TRU-Install virtual CD will be allowed to enumerate
as a CD-Rom so that either (a) a user can install the packaged software
or (b) a user-space application (e.g. udev) can switch it to modem mode.
This patch does allow for manual override by adding a usb-storage module
parameter 'swi_tru_install' which can force the modem into either mode
regardless of what packages it contains.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kevin Lloyd [Thu, 10 Jul 2008 21:14:51 +0000 (14:14 -0700)]
USB Serial Sierra: Dynamic interface detection
This patch changes the method by which the number of ports per interface is
assigned so that it is more dynamic and calculated on the fly (as opposed to
hard coding it). This will allow for faster and easier addition of products.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 21 Jul 2008 14:08:28 +0000 (10:08 -0400)]
usb-storage: unusual_devs entries for iRiver T10 and Datafab CF+SM reader
This patch (as1115) adds unusual_devs entries with the IGNORE_RESIDE
flag for the iRiver T10 and the Simple Tech/Datafab CF+SM card
reader. Apparently these devices provide reasonable residue values
for READ and WRITE operations, but not for others like INQUIRY or READ
CAPACITY.
This fixes the iRiver T10 problem reported in Bugzilla #11125.
Simon Arlott [Mon, 21 Jul 2008 19:44:50 +0000 (20:44 +0100)]
USB: Move usb/mon/ up to misc options in Kconfig
This makes "USB Monitor" appear under "Miscellaneous USB options"
section instead of in the middle of device specific drivers in the
"USB Imaging devices" section.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 29 Jul 2008 15:58:06 +0000 (11:58 -0400)]
usb-storage: automatically recognize bad residues
This patch (as1119) will help to reduce the clutter of usb-storage's
unusual_devs file by automatically detecting some devices that need
the IGNORE_RESIDUE flag. The idea is that devices should never return
a non-zero residue for an INQUIRY or a READ CAPACITY command unless
they failed to transfer all the requested data. So if one of these
commands transfers a standard amount of data but there is a positive
residue, we know that the residue is bogus and we can set the flag.
This fixes the problems reported in Bugzilla #11125.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Wed, 30 Jul 2008 15:31:50 +0000 (11:31 -0400)]
USB: fix interface unregistration logic
This patch (as1122) fixes a bug: When an interface is unregistered,
its children (sysfs files and endpoint devices) are unregistered after
it instead of before.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Kay Sievers <kay.sievers@vrfy.org> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 29 Jul 2008 16:01:04 +0000 (12:01 -0400)]
usb-serial: don't release unregistered minors
This patch (as1121) fixes a bug in the USB serial core. When a device
is unregistered, the core will give back its minors -- even if the
device hasn't been assigned any!
The patch reserves the highest minor value (255) to mean that no minor
was assigned. It also removes some dead code and does a small style
fixup.
Dave Jones [Mon, 14 Jul 2008 17:28:34 +0000 (13:28 -0400)]
USB: usb-storage: quirk around v1.11 firmware on Nikon D4
usb-storage: quirk around v1.11 firmware on Nikon D40
https://bugzilla.redhat.com/show_bug.cgi?id=454028
Just as in earlier firmware versions, we need to perform this
quirk for the latest version too.
Speculatively do the entry for the D80 too, as they seem to
have the same firmware problems historically.
Signed-off-by: Dave Jones <davej@redhat.com> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 21 Jul 2008 13:56:26 +0000 (09:56 -0400)]
USB: OHCI: fix system hang caused by earlier patch
This patch (as1114) fixes a problem that was revealed by an earlier
patch (as1069b). Some broken controllers seem never to turn off their
RHCS interrupt status bit, even when told to do so. As a result they
generate an interrupt storm and hang the system.
The patch avoids enabling RHSC interrupt requests when the RHCS status
bit is already set. This should have no adverse affects on normal
controllers, since they won't set the status bit until a root-hub
status change actually occurs, in which case we wouldn't enable RHSC
interrupt requests anyway -- we would wait until the status change had
been processed and cleared.
David Brownell [Sat, 26 Jul 2008 15:06:24 +0000 (08:06 -0700)]
USB: fix USB boot crash, ecm_do_notify(), list_add corruption. prev->next should be next (ffff88003b8f82f8)
This fixes a BUG() turned up by Ingo via randconfig testing, where
CONFIG_LIST_DEBUG turned up list corruption. The corruption was
caused by the dummy_hcd (single-machine test harness for gadget and
HCD code) trashing the request queue when driven by the new CDC
composite gadget an I/O pattern that was previously uncommon.
Fix suggested by Alan Stern.
Wolfgang Mües [Tue, 29 Jul 2008 09:54:43 +0000 (11:54 +0200)]
usb: auerswald: remove driver (obsolete)
This patch removes the auerswald USB driver from the linux kernel
2.6.26.
This driver was included into the kernel mainly to connect to the ISDN
framework. This was done in linux 2.4.x. For 2.6.x, due to the fragile
and moving ISDN support, this connection was never realized, and the
only use of this driver was for device configuration. In the age of DSL,
the demand of ISDN support is getting very low.
Meanwhile, with the advent of libusb, an userspace driver was done for
the device configuration which works fine for linux and mac. (Thanks to
the libusb developers!). The userspace driver is downloadable from the
auerswald web site.
So this driver is obsolete now and has to be removed. Many thanks to all
developers which helped me to bring this driver up and working.
Signed-off-by: Wolfgang Muees <wolfgang@iksw-muees.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Howells [Wed, 13 Aug 2008 15:20:04 +0000 (16:20 +0100)]
CRED: Introduce credential access wrappers
The patches that are intended to introduce copy-on-write credentials for 2.6.28
require abstraction of access to some fields of the task structure,
particularly for the case of one task accessing another's credentials where RCU
will have to be observed.
Introduced here are trivial no-op versions of the desired accessors for current
and other tasks so that other subsystems can start to be converted over more
easily.
Wrappers are introduced into a new header (linux/cred.h) for UID/GID,
EUID/EGID, SUID/SGID, FSUID/FSGID, cap_effective and current's subscribed
user_struct. These wrappers are macros because the ordering between header
files mitigates against making them inline functions.
linux/cred.h is #included from linux/sched.h.
Further, XFS is modified such that it no longer defines and uses parameterised
versions of current_fs[ug]id(), thus getting rid of the namespace collision
otherwise incurred.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: James Morris <jmorris@namei.org>
Daniel Lezcano [Wed, 13 Aug 2008 23:15:57 +0000 (16:15 -0700)]
netns: Fix crash by making igmp per namespace
This patch makes the multicast socket to be per namespace.
When a network namespace is created, other than the init_net and a
multicast packet is received, the kernel goes to a hang or a kernel panic.
How to reproduce ?
* create a child network namespace
* create a pair virtual device veth
* ip link add type veth
* move one side to the pair network device to the child namespace
* ip link set netns <childpid> dev veth1
* ping -I veth0 224.0.0.1
The bug appears because the function ip_mc_init_dev does not initialize
the different multicast fields as it exits because it is not the init_net.
BUG: soft lockup - CPU#0 stuck for 61s! [avahi-daemon:2695]
Modules linked in:
irq event stamp: 50350
hardirqs last enabled at (50349): [<c03ee949>] _spin_unlock_irqrestore+0x34/0x39
hardirqs last disabled at (50350): [<c03ec639>] schedule+0x9f/0x5ff
softirqs last enabled at (45712): [<c0374d4b>] ip_setsockopt+0x8e7/0x909
softirqs last disabled at (45710): [<c03ee682>] _spin_lock_bh+0x8/0x27
Eilon Greenstein [Wed, 13 Aug 2008 22:58:49 +0000 (15:58 -0700)]
bnx2x: Minor code improvements
Minor code improvements
Small changes to make the code a little bit more efficient and mostly
more readable:
- Using unified macros for EMAC_RD/WR which looks like normal REG_RD/WR
- Removing the NIG_WR since it did nothing and was only confusing
- On bnx2x_panic_dump, print only the used parts of the rings
- define parameters only on the branch they are needed and not at the
beginning of the function
- using NETIF_MSG_INTR and not private BNX2X_MSG_SP for debug prints
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Wed, 13 Aug 2008 22:58:30 +0000 (15:58 -0700)]
bnx2x: Driver info
Driver info
The internal FW which is downloaded by the driver should not be
displayed - it is only causing confusion and it is redundant since it
can be concluded from the driver version. Display only FW which is
burned on the board nvram
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Wed, 13 Aug 2008 22:57:28 +0000 (15:57 -0700)]
bnx2x: 8073 PHY changes
8073 PHY changes
The initial support we had for this PHY needs some serious changing. The
major change is that this PHY should be initialized only when the first
function is loaded and not for each function. The official SPI-ROM of
this PHY was released and it requires some changes in the initialization
code as well
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Wed, 13 Aug 2008 22:56:59 +0000 (15:56 -0700)]
bnx2x: Change GPIO for any port
Change GPIO for any port
The set GPIO function should receive the port index to allow changing
the GPIO of another port. This is needed for the common init phase (one
the first driver is loaded for the chip)
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Wed, 13 Aug 2008 22:56:17 +0000 (15:56 -0700)]
bnx2x: Pause settings
Pause settings
- 1G pause was not working due to missing write to the emac block
(TX_MODE_FLOW_EN)
- The flow control should use the negotiated result (after autoneg) so
we should save both the requested autoneg and the result
- The HW credits with flow control at 1G speed were not optimized and
caused low throughput
- It is recommended to turn off flow control if the MTU is bigger than
5000B due to internal buffers size
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Wed, 13 Aug 2008 22:55:28 +0000 (15:55 -0700)]
bnx2x: Link order with external PHY
Link order with external PHY
When external PHY exists (second chip with the PHY to translate to
another physical medium) the link with the eternal PHY and the network
should be established before setting the link between the 5771x and the
PHY. This is the right order and it is important when using autoneg -
the link to the network should use the autoneg and the link between the
two chips should be forced to the network result.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
No LRO without Rx checksum
Disabling LRO when Rx checksum is disabled
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yitchak Gertner [Wed, 13 Aug 2008 22:53:12 +0000 (15:53 -0700)]
bnx2x: Wrong structure size
Wrong structure size
The wrong structure was used in the sizeof to clear (luckily both
structures have the same size in this version...)
Signed-off-by: Yitchak Gertner <gertner@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6 / log