Jay Vosburgh [Wed, 10 Oct 2007 02:57:24 +0000 (19:57 -0700)]
net/bonding: Optionally allow ethernet slaves to keep own MAC
Update the "don't change MAC of slaves" functionality added in
previous changes to be a generic option, rather than something tied to
IB devices, as it's occasionally useful for regular ethernet devices as
well.
Adds "fail_over_mac" option (which is automatically enabled for IB
slaves), applicable only to active-backup mode.
Includes documentation update.
Updates bonding driver version to 3.2.0.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Moni Shoua [Wed, 10 Oct 2007 02:43:43 +0000 (19:43 -0700)]
net/bonding: Destroy bonding master when last slave is gone
When bonding enslaves non Ethernet devices it takes pointers to functions
in the module that owns the slaves. In this case it becomes unsafe
to keep the bonding master registered after last slave was unenslaved
because we don't know if the pointers are still valid. Destroying the bond when slave_cnt is zero
ensures that these functions be used anymore.
Signed-off-by: Moni Shoua <monis at voltaire.com> Acked-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Moni Shoua [Wed, 10 Oct 2007 02:43:42 +0000 (19:43 -0700)]
net/bonding: Delay sending of gratuitous ARP to avoid failure
Delay sending a gratuitous_arp when LINK_STATE_LINKWATCH_PENDING bit
in dev->state field is on. This improves the chances for the arp packet to
be transmitted.
Signed-off-by: Moni Shoua <monis at voltaire.com> Acked-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Moni Shoua [Wed, 10 Oct 2007 02:43:41 +0000 (19:43 -0700)]
net/bonding: Handlle wrong assumptions that slave is always an Ethernet device
bonding sometimes uses Ethernet constants (such as MTU and address length) which
are not good when it enslaves non Ethernet devices (such as InfiniBand).
Signed-off-by: Moni Shoua <monis at voltaire.com> Acked-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Moni Shoua [Wed, 10 Oct 2007 02:43:40 +0000 (19:43 -0700)]
net/bonding: Enable IP multicast for bonding IPoIB devices
Allow to enslave devices when the bonding device is not up. Over the discussion
held at the previous post this seemed to be the most clean way to go, where it
is not expected to cause instabilities.
Normally, the bonding driver is UP before any enslavement takes place.
Once a netdevice is UP, the network stack acts to have it join some multicast groups
(eg the all-hosts 224.0.0.1). Now, since ether_setup() have set the bonding device
type to be ARPHRD_ETHER and address len to be ETHER_ALEN, the net core code
computes a wrong multicast link address. This is b/c ip_eth_mc_map() is called
where for multicast joins taking place after the enslavement another ip_xxx_mc_map()
is called (eg ip_ib_mc_map() when the bond type is ARPHRD_INFINIBAND)
Signed-off-by: Moni Shoua <monis at voltaire.com> Signed-off-by: Or Gerlitz <ogerlitz at voltaire.com> Acked-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Moni Shoua [Wed, 10 Oct 2007 02:43:39 +0000 (19:43 -0700)]
net/bonding: Enable bonding to enslave netdevices not supporting set_mac_address()
This patch allows for enslaving netdevices which do not support
the set_mac_address() function. In that case the bond mac address is the one
of the active slave, where remote peers are notified on the mac address
(neighbour) change by Gratuitous ARP sent by bonding when fail-over occurs
(this is already done by the bonding code).
Signed-off-by: Moni Shoua <monis at voltaire.com> Signed-off-by: Or Gerlitz <ogerlitz at voltaire.com> Acked-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Moni Shoua [Wed, 10 Oct 2007 02:43:38 +0000 (19:43 -0700)]
net/bonding: Enable bonding to enslave non ARPHRD_ETHER
This patch changes some of the bond netdevice attributes and functions
to be that of the active slave for the case of the enslaved device not being
of ARPHRD_ETHER type. Basically it overrides those setting done by ether_setup(),
which are netdevice **type** dependent and hence might be not appropriate for
devices of other types. It also enforces mutual exclusion on bonding slaves
from dissimilar ether types, as was concluded over the v1 discussion.
IPoIB (see Documentation/infiniband/ipoib.txt) MAC address is made of a 3 bytes
IB QP (Queue Pair) number and 16 bytes IB port GID (Global ID) of the port this
IPoIB device is bounded to. The QP is a resource created by the IB HW and the
GID is an identifier burned into the HCA (i have omitted here some details which
are not important for the bonding RFC).
Signed-off-by: Moni Shoua <monis at voltaire.com> Signed-off-by: Or Gerlitz <ogerlitz at voltaire.com> Acked-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Moni Shoua [Wed, 10 Oct 2007 02:43:37 +0000 (19:43 -0700)]
IB/ipoib: Verify address handle validity on send
When the bonding device senses a carrier loss of its active slave it replaces
that slave with a new one. In between the times when the carrier of an IPoIB
device goes down and ipoib_neigh is destroyed, it is possible that the
bonding driver will send a packet on a new slave that uses an old ipoib_neigh.
This patch detects and prevents this from happenning.
Signed-off-by: Moni Shoua <monis at voltaire.com> Signed-off-by: Or Gerlitz <ogerlitz at voltaire.com> Acked-by: Roland Dreier <rdreier@cisco.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Moni Shoua [Wed, 10 Oct 2007 02:43:36 +0000 (19:43 -0700)]
IB/ipoib: Bound the net device to the ipoib_neigh structue
IPoIB uses a two layer neighboring scheme, such that for each struct neighbour
whose device is an ipoib one, there is a struct ipoib_neigh buddy which is
created on demand at the tx flow by an ipoib_neigh_alloc(skb->dst->neighbour)
call.
When using the bonding driver, neighbours are created by the net stack on behalf
of the bonding (master) device. On the tx flow the bonding code gets an skb such
that skb->dev points to the master device, it changes this skb to point on the
slave device and calls the slave hard_start_xmit function.
Under this scheme, ipoib_neigh_destructor assumption that for each struct
neighbour it gets, n->dev is an ipoib device and hence netdev_priv(n->dev)
can be casted to struct ipoib_dev_priv is buggy.
To fix it, this patch adds a dev field to struct ipoib_neigh which is used
instead of the struct neighbour dev one, when n->dev->flags has the
IFF_MASTER bit set.
Signed-off-by: Moni Shoua <monis at voltaire.com> Signed-off-by: Or Gerlitz <ogerlitz at voltaire.com> Acked-by: Roland Dreier <rdreier@cisco.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Mark Brown [Wed, 10 Oct 2007 10:05:44 +0000 (11:05 +0100)]
natsemi: Use round_jiffies() for slow timers
Unless we have failed to fill the RX ring the timer used by the natsemi
driver is not particularly urgent and can use round_jiffies() to allow
grouping with other timers.
Signed-off-by: Mark Brown <broonie@sirena.org.uk> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Linus Torvalds [Mon, 15 Oct 2007 17:46:05 +0000 (10:46 -0700)]
Merge git://git.linux-nfs.org/pub/linux/nfs-2.6
* git://git.linux-nfs.org/pub/linux/nfs-2.6: (131 commits)
NFSv4: Fix a typo in nfs_inode_reclaim_delegation
NFS: Add a boot parameter to disable 64 bit inode numbers
NFS: nfs_refresh_inode should clear cache_validity flags on success
NFS: Fix a connectathon regression in NFSv3 and NFSv4
NFS: Use nfs_refresh_inode() in ops that aren't expected to change the inode
SUNRPC: Don't call xprt_release in call refresh
SUNRPC: Don't call xprt_release() if call_allocate fails
SUNRPC: Fix buggy UDP transmission
[23/37] Clean up duplicate includes in
[2.6 patch] net/sunrpc/rpcb_clnt.c: make struct rpcb_program static
SUNRPC: Use correct type in buffer length calculations
SUNRPC: Fix default hostname created in rpc_create()
nfs: add server port to rpc_pipe info file
NFS: Get rid of some obsolete macros
NFS: Simplify filehandle revalidation
NFS: Ensure that nfs_link() returns a hashed dentry
NFS: Be strict about dentry revalidation when doing exclusive create
NFS: Don't zap the readdir caches upon error
NFS: Remove the redundant nfs_reval_fsid()
NFSv3: Always use directory post-op attributes in nfs3_proc_lookup
...
Fix up trivial conflict due to sock_owned_by_user() cleanup manually in
net/sunrpc/xprtsock.c
Linus Torvalds [Mon, 15 Oct 2007 15:18:44 +0000 (08:18 -0700)]
Merge branch 'agp-patches' of master.kernel.org:/pub/scm/linux/kernel/git/airlied/agp-2.6
* 'agp-patches' of master.kernel.org:/pub/scm/linux/kernel/git/airlied/agp-2.6:
fix use after free in amd create gatt pages
AGP fix race condition between unmapping and freeing pages
Linus Torvalds [Mon, 15 Oct 2007 15:17:26 +0000 (08:17 -0700)]
Merge branch 'drm-patches' of ssh://master.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-patches' of ssh://master.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
via invalid device ids removal
radeon: Commit the ring after each partial texture upload blit.
i915: fix vbl swap allocation size.
drm: Replace DRM_IOCTL_ARGS with (dev, data, file_priv) and remove DRM_DEVICE.
drm: remove XFREE86_VERSION macros.
drm: Replace filp in ioctl arguments with drm_file *file_priv.
drm: Remove DRM_ERR OS macro.
Linus Torvalds [Mon, 15 Oct 2007 15:16:53 +0000 (08:16 -0700)]
Merge branch 'nfs-server-stable' of git://linux-nfs.org/~bfields/linux
* 'nfs-server-stable' of git://linux-nfs.org/~bfields/linux:
knfsd: query filesystem for NFSv4 getattr of FATTR4_MAXNAME
knfsd: nfsv4 delegation recall should take reference on client
knfsd: don't shutdown callbacks until nfsv4 client is freed
knfsd: let nfsd manage timing out its own leases
knfsd: Add source address to sunrpc svc errors
knfsd: 64 bit ino support for NFS server
svcgss: move init code into separate function
knfsd: remove code duplication in nfsd4_setclientid()
nfsd warning fix
knfsd: fix callback rpc cred
knfsd: move nfsv4 slab creation/destruction to module init/exit
knfsd: spawn kernel thread to probe callback channel
knfsd: nfs4 name->id mapping not correctly parsing negative downcall
knfsd: demote some printk()s to dprintk()s
knfsd: cleanup of nfsd4 cmp_* functions
knfsd: delete code made redundant by map_new_errors
nfsd: fix horrible indentation in nfsd_setattr
nfsd: remove unused cache_for_each macro
nfsd: tone down inaccurate dprintk
Jiri Kosina [Mon, 15 Oct 2007 13:17:41 +0000 (15:17 +0200)]
HID: fix HIDIOCGRDESC memory access in hidraw
Fix bogus copying of data into userspace when HIDIOCGRDESC is issued.
HID-transport layer makes sure that dev->hid->rdesc is not larger than
HID_MAX_DESCRIPTOR_SIZE.
Ingo Molnar [Mon, 15 Oct 2007 15:00:20 +0000 (17:00 +0200)]
sched: sync wakeups preempt too
make sure sync wakeups preempt too - the scheduler will not
overschedule as we've got various throttles against that.
As a result, sync wakeups can be used more widely in the kernel
(to signal wakeup affinity between tasks), and no arbitrary
latencies will be introduced either.
Ingo Molnar [Mon, 15 Oct 2007 15:00:19 +0000 (17:00 +0200)]
sched: affine sync wakeups
make sync wakeups affine for cache-cold tasks: if a cache-cold task
is woken up by a sync wakeup then use the opportunity to migrate it
straight away. (the two tasks are 'related' because they communicate)
Laurent Vivier [Mon, 15 Oct 2007 15:00:19 +0000 (17:00 +0200)]
sched: guest CPU accounting: maintain stats in account_system_time()
modify account_system_time() to add cputime to cpustat->guest if we are
running a VCPU. We add this cputime to cpustat->user instead of
cpustat->system because this part of KVM code is in fact user code
although it is executed in the kernel. We duplicate VCPU time between
guest and user to allow an unmodified "top(1)" to display correct value.
A modified "top(1)" is able to display good cpu user time and cpu guest
time by subtracting cpu guest time from cpu user time. Update "gtime" in
task_struct accordingly.
Laurent Vivier [Mon, 15 Oct 2007 15:00:19 +0000 (17:00 +0200)]
sched: guest CPU accounting: add guest-CPU /proc/<pid>/stat fields
like for cpustat, introduce the "gtime" (guest time of the task) and
"cgtime" (guest time of the task children) fields for the
tasks. Modify signal_struct and task_struct.
Modify /proc/<pid>/stat to display these new fields.
Laurent Vivier [Mon, 15 Oct 2007 15:00:19 +0000 (17:00 +0200)]
sched: guest CPU accounting: add guest-CPU /proc/stat field
as recent CPUs introduce a third running state, after "user" and
"system", we need a new field, "guest", in cpustat to store the time
used by the CPU to run virtual CPU. Modify /proc/stat to display this
new field.
Milton Miller [Mon, 15 Oct 2007 15:00:19 +0000 (17:00 +0200)]
sched: domain sysctl fixes: do not crash on allocation failure
Now that we are calling this at runtime, a more relaxed error path is
suggested. If an allocation fails, we just register the partial table,
which will show empty directories.
Signed-off-by: Milton Miller <miltonm@bga.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Milton Miller [Mon, 15 Oct 2007 15:00:19 +0000 (17:00 +0200)]
sched: domain sysctl fixes: unregister the sysctl table before domains
Unregister and free the sysctl table before destroying domains, then
rebuild and register after creating the new domains. This prevents the
sysctl table from pointing to freed memory for root to write.
Signed-off-by: Milton Miller <miltonm@bga.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Milton Miller [Mon, 15 Oct 2007 15:00:19 +0000 (17:00 +0200)]
sched: domain sysctl fixes: use for_each_online_cpu()
init_sched_domain_sysctl was walking cpus 0-n and referencing per_cpu
variables. If the cpus_possible mask is not contigious this will result
in a crash referencing unallocated data. If the online mask is not
contigious then we would show offline cpus and miss online ones.
Signed-off-by: Milton Miller <miltonm@bga.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Arjan van de Ven [Mon, 15 Oct 2007 15:00:19 +0000 (17:00 +0200)]
Make scheduler debug file operations const
In general, struct file_operations are const in the kernel, to not have
false cacheline sharing and to catch bugs at compiletime with accidental
writes to them. The new scheduler code introduces a new non-const one;
fix this up.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ingo Molnar [Mon, 15 Oct 2007 15:00:18 +0000 (17:00 +0200)]
sched: do not normalize kernel threads via SysRq-N
do not normalize kernel threads via SysRq-N: the migration threads,
softlockup threads, etc. might be essential for the system to
function properly. So only zap user tasks.
Andi Kleen [Mon, 15 Oct 2007 15:00:14 +0000 (17:00 +0200)]
sched: cleanup: refactor common code of sleep_on / wait_for_completion
Refactor common code of sleep_on / wait_for_completion
These functions were largely cut'n'pasted. This moves
the common code into single helpers instead. Advantage
is about 1k less code on x86-64 and 91 lines of code removed.
It adds one function call to the non timeout version of
the functions; i don't expect this to be measurable.
Mike Galbraith [Mon, 15 Oct 2007 15:00:14 +0000 (17:00 +0200)]
sched: prevent wakeup over-scheduling
Prevent wakeup over-scheduling. Once a task has been preempted by a
task of the same or lower priority, it becomes ineligible for repeated
preemption by same until it has been ticked, or slept. Instead, the
task is marked for preemption at the next tick. Tasks of higher
priority still preempt immediately.
Signed-off-by: Mike Galbraith <efault@gmx.de> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Dmitry Adamushko [Mon, 15 Oct 2007 15:00:14 +0000 (17:00 +0200)]
sched: fix group scheduling for SCHED_BATCH
The following patch (sched: disable sleeper_fairness on SCHED_BATCH)
seems to break GROUP_SCHED. Although, it may be 'oops'-less due to the
possibility of 'p' being always a valid address.
Gautham R Shenoy [Mon, 15 Oct 2007 15:00:14 +0000 (17:00 +0200)]
sched: fix rt ptracer monopolizing CPU
yield() in wait_task_inactive(), can cause a high priority thread to be
scheduled back in, and there by loop forever while it is waiting for some
lower priority thread which is unfortunately still on the runqueue.
Use schedule_timeout_uninterruptible(1) instead.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Credit: Oleg Nesterov <oleg@tv-sign.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Dhaval Giani [Mon, 15 Oct 2007 15:00:14 +0000 (17:00 +0200)]
sched: group scheduling, sysfs tunables
Add tunables in sysfs to modify a user's cpu share.
A directory is created in sysfs for each new user in the system.
/sys/kernel/uids/<uid>/cpu_share
Reading this file returns the cpu shares granted for the user.
Writing into this file modifies the cpu share for the user. Only an
administrator is allowed to modify a user's cpu share.
Paul E. McKenney [Mon, 15 Oct 2007 15:00:14 +0000 (17:00 +0200)]
sched: export cpu_clock()
export cpu_clock() - the preferred API instead of sched_clock().
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Dmitry Adamushko [Mon, 15 Oct 2007 15:00:13 +0000 (17:00 +0200)]
sched: tidy up SCHED_RR
- make timeslices of SCHED_RR tasks constant and not
dependent on task's static_prio [1] ;
- remove obsolete code (timeslice related bits);
- make sched_rr_get_interval() return something more
meaningful [2] for SCHED_OTHER tasks.
[1] according to the following link, it's not compliant with SUSv3
(not sure though, what is the reference for us :-)
http://lkml.org/lkml/2007/3/7/656
[2] the interval is dynamic and can be depicted as follows "should a
task be one of the runnable tasks at this particular moment, it would
expect to run for this interval of time before being re-scheduled by the
scheduler tick".
(i.e. it's more precise if a task is runnable at the moment)
yeah, this seems to require task_rq_lock/unlock() but this is not a hot
path.
Dmitry Adamushko [Mon, 15 Oct 2007 15:00:13 +0000 (17:00 +0200)]
sched: fix __pick_next_entity()
The thing is that __pick_next_entity() must never be called when
first_fair(cfs_rq) == NULL. It wouldn't be a problem, should 'run_node'
be the very first field of 'struct sched_entity' (and it's the second).
The 'nr_running != 0' check is _not_ enough, due to the fact that
'current' is not within the tree. Generic paths are ok (e.g. schedule()
as put_prev_task() is called previously)... I'm more worried about e.g.
migration_call() -> CPU_DEAD_FROZEN -> migrate_dead_tasks()... if
'current' == rq->idle, no problems.. if it's one of the SCHED_NORMAL
tasks (or imagine, some other use-cases in the future -- i.e. we should
not make outer world dependent on internal details of sched_fair class)
-- it may be "Houston, we've got a problem" case.
it's +16 bytes to the ".text". Another variant is to make 'run_node' the
first data member of 'struct sched_entity' but an additional check (se !
= NULL) is still needed in pick_next_entity().
There is a possibility that because of task of a group moving from one
cpu to another, it may gain more cpu time that desired. See
http://marc.info/?l=linux-kernel&m=119073197730334 for details.
This is an attempt to fix that problem. Basically it simulates dequeue
of higher level entities as if they are going to sleep. Similarly it
simulate wakeup of higher level entities as if they are waking up from
sleep.
The adjusting sched_class is a missing part of the already existing "do
not leak PI boosting priority to the child" at the sched_fork(). This
patch moves the adjusting sched_class from wake_up_new_task() to
sched_fork().
this also shrinks the code a bit:
text data bss dec hex filename
40111 4018 292 44421 ad85 sched.o.before
40102 4018 292 44412 ad7c sched.o.after
Ingo Molnar [Mon, 15 Oct 2007 15:00:11 +0000 (17:00 +0200)]
sched: fix sched_fork()
fix sched_fork(): large latencies at new task creation time because
the ->vruntime was not fixed up cross-CPU, if the parent got migrated
after the child's CPU got set up.
Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
projects / linux-2.6 / log