Sergey Vlasov [Mon, 22 Aug 2005 11:43:39 +0000 (13:43 +0200)]
[ALSA] HP nx6110 quirks
Intel8x0 driver,AC97 Codec
The HP nx6110 laptop needs to have Headphone Jack Sense enabled so
that the internal speakers will be turned off when headphones are
plugged in.
Also ac97_quirk=hp_only is needed to make a single Master volume in
the mixer instead of separate volumes for internal speakers and
headphones, which just confuses the user.
Jaroslav Kysela [Thu, 18 Aug 2005 11:43:12 +0000 (13:43 +0200)]
[ALSA] PCM resume cleanups
Digigram VX core,CS4231 driver,ATIIXP driver,VIA82xx driver
VIA82xx-modem driver,au88x0 driver,CS46xx driver,Trident driver
This patch disables SNDRV_PCM_INFO_RESUME flag for drivers which does not
support the full resume.
Takashi Iwai [Tue, 16 Aug 2005 14:54:12 +0000 (16:54 +0200)]
[ALSA] nm256 - Fix PM and irq handling
NM256 driver
- Fixed the PCM resume - restoring the rate setting
- Fixed the handling of buggy irqs
- Dynamically acquire/release irq handler to make the driver more robust
to unknown irq storms (as OSS driver does).
Clemens Ladisch [Mon, 15 Aug 2005 06:35:25 +0000 (08:35 +0200)]
[ALSA] usb-audio: use vmalloc for the PCM buffer
USB generic driver
With the double buffering, we no longer need contiguous memory for the
PCM buffer, so we can use vmalloc() instead of the preallocation
functions, and increase the maximum size to 256 KB.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Clemens Ladisch [Mon, 15 Aug 2005 06:24:44 +0000 (08:24 +0200)]
[ALSA] usb-audio: double-buffer all playback data
USB generic driver
We always had to use double buffering when capturing, and when playback
data for one URB crosses a buffer boundary. The latter would make hwptr
updates less precise because the double-buffered data is read from the
buffer much earlier than the other data is read by the host controller.
Double-buffering all data allows to update hwptr immediately after the
data was copied to the USB buffer(s), which has the additional benefit
of avoiding the latency imposed by the host controller's delay of up to
one frame when interrupting.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Clemens Ladisch [Mon, 15 Aug 2005 06:22:39 +0000 (08:22 +0200)]
[ALSA] usb-audio: optimize handling of capture URBs
USB generic driver
When preparing capture URBs, we don't need to stop when we cross a
period boundary because we now never handle more than one millisecond of
data per URB anyway.
When handling captured data, use an extra flag to call
snd_pcm_period_elapsed() no more than once. This allows us to move the
period boundary checking code before the copying of the data which
avoids a second locking of the substream's lock.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Clemens Ladisch [Fri, 12 Aug 2005 13:19:39 +0000 (15:19 +0200)]
[ALSA] usb-audio: schedule high speed URBs with 1 ms alignment
USB generic driver
The EHCI driver doesn't interrupt more than once per millisecond, and
organizes all iso transfers with frame-sized ITDs, so we can (try to)
be more efficient by aligning all URBs on frame boundaries.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Clemens Ladisch [Fri, 12 Aug 2005 06:28:27 +0000 (08:28 +0200)]
[ALSA] usb-audio: fix packets per URB calculation for playback
USB generic driver
When determining how many packets are needed for one period, we cannot
assume that all packets have their maximum size -- we always use the
nominal sample rate when sending data, and could use an even lower rate
when the endpoint uses frequency feedback.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Clemens Ladisch [Fri, 12 Aug 2005 06:25:26 +0000 (08:25 +0200)]
[ALSA] usb-audio: use 1 ms URBs when capturing
USB generic driver
When capturing audio data, we do not know beforehand how many samples
the device sends per frame, so we have to use URBs that are as short as
possible to make sure that we can handle period boundaries without any
additional latencies.
Furthermore, the total count of URBs submitted doesn't matter when
capturing, so we can just use the maximum number.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Clemens Ladisch [Thu, 11 Aug 2005 13:59:17 +0000 (15:59 +0200)]
[ALSA] make local objects static
Memalloc module,PCM Midlevel,Timer Midlevel,GUS Library,AC97 Codec
ALI5451 driver,RME9652 driver
Make some functions/variables that are used in only one file static.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
PCM Midlevel,ALSA<-OSS emulation,USB USX2Y
This patch removes open_flag from struct _snd_pcm_substream.
All of its uses are substituted by querying struct _snd_pcm_substream's
member ffile instead.
Liam Girdwood [Fri, 5 Aug 2005 08:24:36 +0000 (10:24 +0200)]
[ALSA] PXA27x AC97 warm reset
ARM PXA2XX driver
This patch extends the period of an AC97 warm reset on the PXA27x from
50uS to 500uS. The shorter reset didn't always guarantee that the codec
would wake up.
Changes:-
o Change pxa27x warm reset period to 500uS
o Removed double semi-colon.
Clemens Ladisch [Wed, 3 Aug 2005 11:50:30 +0000 (13:50 +0200)]
[ALSA] use PCM interface for IEC958 controls
Digigram VX core,ENS1370/1+ driver,CA0106 driver,EMU10K1/EMU10K2 driver
RME HDSP driver,RME9652 driver
For consistency, use the PCM interface instead of MIXER for IEC958
default/mask/stream mixer controls.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Clemens Ladisch [Wed, 3 Aug 2005 11:40:08 +0000 (13:40 +0200)]
[ALSA] use SNDRV_CTL_NAME_IEC958 macro
CMI8330 driver,ENS1370/1+ driver,FM801 driver,VIA82xx driver,AC97 Codec
ALI5451 driver,CS46xx driver,EMU10K1/EMU10K2 driver,HDA Codec driver
ICE1712 driver,ICE1724 driver
Where appropriate, use the SNDRV_CTL_NAME_IEC958 instead of a literal
string.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
AC97 Codec,PCI drivers
I've made the review changes and as requested I've pasted the RFC by
Nicolas below:-
'I would like to know what people think of the following patch. It
allows for a codec on an AC97 bus to be shared with other drivers which
are completely unrelated to audio. It registers a new bus type, and
whenever a codec instance is created then a device for it is also
registered with the driver model using that bus type. This allows, for
example, to use the extra features of the UCB1400 like the touchscreen
interface and the additional GPIOs and ADCs available on that chip for
battery monitoring. I have a working UCB1400 touchscreen driver here
that simply registers with the driver model happily working alongside
with audio features using this.'
Changes over RFC:-
o Now matches codec name within codec group.
o Added ac97_dev_release() to stop kernel complaining about no release
method for device.
o Added 'config SND_AC97_BUS' to sound/pci/Kconfig and moved 'config
SND_AC97_CODEC' out with the PCI=n statement.
o module is now called snd-ac97-bus
Clemens Ladisch [Fri, 29 Jul 2005 13:32:58 +0000 (15:32 +0200)]
[ALSA] sound - fix .iface field of mixer control elements
Documentation,CS46xx driver,EMU10K1/EMU10K2 driver,AD1848 driver
SB16/AWE driver,CMIPCI driver,ENS1370/1+ driver,RME32 driver
RME96 driver,ICE1712 driver,ICE1724 driver,KORG1212 driver
RME HDSP driver,RME9652 driver
This patch changes .iface to SNDRV_CTL_ELEM_IFACE_MIXER whre _PCM or
_HWDEP was used in controls that are not associated with a specific PCM
(sub)stream or hwdep device, and changes some controls that got
inconsitent .iface values due to copy+paste errors. Furthermore, it
makes sure that all control that do use _PCM or _HWDEP use the correct
number in the .device field.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
AC97 Codec
o Enhanced current WM97xx support to provide additional controls and
use the kcontrol suffix naming convention.
o Added AC97_HAS_NO_MIC, AC97_HAS_NO_TONE and AC97_HAS_NO_STD_PCM.
o Cleaned up WM97xx related comments.
o Removed some wm9713 double mono controls and replaced with stereo
controls.
David Gibson [Wed, 27 Jul 2005 05:47:23 +0000 (15:47 +1000)]
[PATCH] Remove nested feature sections
The {BEGIN,END}_FTR_SECTION asm macros used in ppc64 to nop out
sections of code at runtime cannot be nested. However, we do nest
them in hash_low.S. We get away with it there, because there is
nothing between the BEGIN markers for each section. However, that's
confusing to someone reading the code.
This patch removes the nested ifset and ifclr feature sections,
replacing them with a single feature section in the full mask/value
form.
Signed-off-by: David Gibson <dwg@au1.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Olof Johansson [Mon, 29 Aug 2005 02:42:10 +0000 (21:42 -0500)]
[PATCH] PPC64: Don't try to claim memory from OF at 1GB mark
Some RS64-based machines (p620, F80, others) have problems with firmware
returning 0xdeadbeef instead of failure to allocations that end at the
1GB mark.
We have two options:
1. Detect the undocumented 0xdeadbeef return value and interpret it as
a failure.
2. Avoid allocating that high.
(2) is really the cleaner solution here. 768MB is plenty of room so use
that as the max alloc_top instead of 1GB.
Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Paul Mackerras <paulus@samba.org>
Stephen Rothwell [Mon, 29 Aug 2005 03:15:50 +0000 (13:15 +1000)]
[PATCH] Create include/asm-powerpc
The ppc and ppc64 trees are hopefully going to merge over time, so this
patch begins the process by creating a place for the merging of the
header files.
Create include/asm-powerpc (and move linkage.h into it from
asm-{ppc,ppc64} since we don't like empty directories). Modify the
ppc and ppc64 Makefiles to cope.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Stephen Rothwell [Mon, 29 Aug 2005 08:26:01 +0000 (18:26 +1000)]
[PATCH] fix iSeries build for gcc-3.4
gcc 3.4 (at least the build we are using) puts the gcc generated .ident
string into a .note section at the end of the files it compiles (gcc
3.3.3-hammer and gcc 4.0.2 Debian puts it in the .text section). This
means that the lparmap.s file we produce in the iSeries build may end with
a .note section. When we include it into head.S, the assembler can no
longer resolve some of the conditional branches since the target label
ends up too far away. This patch just forces us back to the .text section
after including lparmap.s.
David Gibson [Tue, 30 Aug 2005 02:54:07 +0000 (12:54 +1000)]
[PATCH] Restore lparmap.s include for iSeries
A mistake rebasing the series of ppc64 head.S cleanup patches meant
the #include of lparmap.s, needed for iSeries was lost. This patch
puts it back again.
Signed-off-by: David Gibson <dwg@au1.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Andrew Morton [Wed, 10 Aug 2005 03:53:41 +0000 (13:53 +1000)]
[PATCH] ppc64: four level pagetables fix
With CONFIG_HUGETLB_PAGE=n:
In file included from kernel/sysctl.c:37:
include/linux/hugetlb.h:104:1: warning: "hugetlb_free_pgd_range" redefined
In file included from include/linux/mm.h:36,
from kernel/sysctl.c:23:
include/asm/pgtable.h:492:1: warning: this is the location of the previous definition
Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: David Gibson <dwg@au1.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Nick Piggin [Sun, 28 Aug 2005 06:49:11 +0000 (16:49 +1000)]
[PATCH] Lazy page table copies in fork()
Defer copying of ptes until fault time when it is possible to reconstruct
the pte from backing store. Idea from Andi Kleen and Nick Piggin.
Thanks to input from Rik van Riel and Linus and to Hugh for correcting
my blundering.
Ray Fucillo <fucillo@intersystems.com> reports:
"I applied this latest patch to a 2.6.12 kernel and found that it does
resolve the problem. Prior to the patch on this machine, I was
seeing about 23ms spent in fork for ever 100MB of shared memory
segment.
After applying the patch, fork is taking about 1ms regardless of the
shared memory size."
Signed-off-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[CCID3]: Call sk->sk_write_space(sk) when receiving a feedback packet
This makes the send rate calculations behave way more closely to what
is specified, with the jitter previously seen on x and x_recv
disappearing completely on non lossy setups.
This resembles the tcp_data_snd_check code, that possibly we'll end up
using in DCCP as well, perhaps moving this code to
inet_connection_sock.
For now I'm doing the simplest implementation tho.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com> Signed-off-by: David S. Miller <davem@davemloft.net>
So that applications can set dccp_sock->dccps_pkt_size, that in turn
is used in the CCID3 half connection init routines to set
ccid3hc[tr]x_s and use it in its rate calculations.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[DCCP]: Introduce dccp_tfrc_lib module with net/dccp/ccids/lib/*.c
I'll now take a look at the other proposed TFRC DCCP CCIDs to find
more code that is now in ccid3.c and move to this module, the loss
event rate, calc_X, etc most probably will be moved there.
The main goal of these changes is to pave the way for the
implementation of more TFRC based DCCP CCIDs and to shrink ccid3.c,
reducing its complexity and helping in getting it rock solid.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[CCID3]: Move the loss interval code to loss_interval.[ch]
And put this into net/dccp/ccids/lib/, where packet_history.[ch] will also be
moved and then we'll have a tfrc_lib.ko module that will be used by
dccp_ccid3.ko and other CCIDs that are variations of TFRC (RFC 3448).
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Introducing functions to add to or subtract from a timeval variable
and renaming now_delta to timeval_new_delta that calls do_gettimeofday
and then timeval_delta, that should be used when there are several
deltas made relative to the current time or setting variables to it,
so as to avoid calling do_gettimeofday excessively.
I'm leaving these "timeval_" prefixed funcions internal to DCCP for a
while till we're sure there are no subtle bugs in it.
It also is more correct as it checks if the number of usecs added to
or subtracted from a tv_usec field is more than 2 seconds.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[DCCP]: Introduce dccp_wait_for_ccid and use it in dccp_write_xmit
This is not quite what I think we should have long term but improves
performance for now, so lets use it till we get CCID3 working well,
then we can think about using sk_write_queue, perhaps using some ideas
from Juwen Lai's old stack for 2.4.20.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6 / log