Ivo van Doorn [Sat, 6 Oct 2007 12:15:46 +0000 (14:15 +0200)]
[PATCH] rt2x00: Add get_tx_data_len callback function
The TX datalen must always be converted to a value rt73 and rt2500usb
understand. Both require to use a different size then skb->len.
First off this is required because the descriptor must be added,
but the second is because the value must be a multiple of either 2 or 4,
and it should not be a multiple of the USB packetmax
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sat, 6 Oct 2007 12:14:29 +0000 (14:14 +0200)]
[PATCH] rt2x00: Move TSF sync values into rt2x00config
All drivers use the same values for TSF sync,
this will move the value determination into rt2x00config.c,
and the definition for the values to rt2x00reg.h
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sat, 6 Oct 2007 12:14:06 +0000 (14:14 +0200)]
[PATCH] rt2x00: Fix rfkill handling
As reported by Modestas Vainius, enabling rkfill in 1 driver and
disabling it in a second could cause a NULL pointer exception when
the rfkill-disabled driver still sets the CONFIG_SUPPORT_HW_BUTTON flag.
Furthermore, rfkill expects the timeout as a value in milliseconds
instead of jiffies. Also increase the timeout to a second,
since this 250ms would be overkill.
Also the flag DEVICE_ENABLED_RADIO_HW is causing problems
for devices which do not support the hardware button
while rfkill is enabled in the driver.
To remidy this we should inverse the flag and its meaning,
rename the flag to DEVICE_DISABLED_RADIO_HW this means that
by default the radio is enabled by the hardware button (if present)
and can only be disabled explicitely.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sat, 6 Oct 2007 12:13:38 +0000 (14:13 +0200)]
[PATCH] rt2x00: Don't use changed_flags inside configure_packet_filter
We shouldn't use changed_flags when configuring the packet filter,
we work directly with the total_flags which is safe enough since
we already check if something has changed after we applied our
packet filtering flag rules.
Also make sure that when the packet filter is scheduled, the
rt2x00dev->interface.filter is cleared to make sure the drivers
will update the packet filter instead of failing at the check:
*total_flags == rt2x00dev->interface.filter
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sat, 6 Oct 2007 12:13:06 +0000 (14:13 +0200)]
[PATCH] rt2x00: Move rt2x00dev flags into enumeration
By putting the flags into a enumeration we can
make it easier maintable since we don't have to
assign numbers for each flag. This makes it easier
to insert and remove flags.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sat, 6 Oct 2007 12:12:42 +0000 (14:12 +0200)]
[PATCH] rt2x00: Store "STARTED" state during suspend
Store the started state into a new flag DEVICE_STARTED_SUSPEND
and set this when suspending while the device was started.
We can't check for is_interface_present() since only mac80211
knows if there are monitor interfaces present.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sat, 6 Oct 2007 12:12:13 +0000 (14:12 +0200)]
[PATCH] rt2x00: Remove radio check from rt2x00lib_toggle_rx
Don't check if the radio is enabled in rt2x00lib_toggle_rx,
this is required since the link tuner should be disabled
when shutting down the device. The remaining calls inside the
rt2x00lib_toggle_rx handler should deliver no problems when
called while the radio is done.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sat, 6 Oct 2007 12:11:46 +0000 (14:11 +0200)]
[PATCH] rt2x00: Remove duplicate code in MAC & BSSID handling
The various drivers contained duplicate code to handle the
MAC and BSSID initialization correctly. This moves the
address copy to little endian variables to rt2x00config.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Williams [Tue, 9 Oct 2007 17:55:24 +0000 (13:55 -0400)]
[PATCH] ipw2200: batch non-user-requested scan result notifications
ipw2200 makes extensive use of background scanning when unassociated or
down. Unfortunately, the firmware sends scan completed events many
times per second, which the driver pushes directly up to userspace.
This needlessly wakes up processes listening for wireless events many
times per second. Batch together scan completed events for
non-user-requested scans and send them up to userspace every 4 seconds.
Scan completed events resulting from an SIOCSIWSCAN call are pushed up
without delay.
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Herbert Xu [Tue, 9 Oct 2007 20:31:47 +0000 (13:31 -0700)]
[IPSEC]: Lock state when copying non-atomic fields to user-space
This patch adds locking so that when we're copying non-atomic fields such as
life-time or coaddr to user-space we don't get a partial result.
For af_key I've changed every instance of pfkey_xfrm_state2msg apart from
expiration notification to include the keys and life-times. This is in-line
with XFRM behaviour.
The actual cases affected are:
* pfkey_getspi: No change as we don't have any keys to copy.
* key_notify_sa:
+ ADD/UPD: This wouldn't work otherwise.
+ DEL: It can't hurt.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 9 Oct 2007 20:30:57 +0000 (13:30 -0700)]
[XFRM] user: Move attribute copying code into copy_to_user_state_extra
Here's a good example of code duplication leading to code rot. The
notification patch did its own netlink message creation for xfrm states.
It duplicated code that was already in dump_one_state. Guess what, the
next time (and the time after) when someone updated dump_one_state the
notification path got zilch.
This patch moves that code from dump_one_state to copy_to_user_state_extra
and uses it in xfrm_notify_sa too. Unfortunately whoever updates this
still needs to update xfrm_sa_len since the notification path wants to
know the exact size for allocation.
At least I've added a comment saying so and if someone still forgest, we'll
have a WARN_ON telling us so.
I also changed the security size calculation to use xfrm_user_sec_ctx since
that's what we actually put into the skb. However it makes no practical
difference since it has the same size as xfrm_sec_ctx.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 9 Oct 2007 20:29:52 +0000 (13:29 -0700)]
[IPSEC]: Move common code into xfrm_alloc_spi
This patch moves some common code that conceptually belongs to the xfrm core
from af_key/xfrm_user into xfrm_alloc_spi.
In particular, the spin lock on the state is now taken inside xfrm_alloc_spi.
Previously it also protected the construction of the response PF_KEY/XFRM
messages to user-space. This is inconsistent as other identical constructions
are not protected by the state lock. This is bad because they in fact should
be protected but only in certain spots (so as not to hold the lock for too
long which may cause packet drops).
The SPI byte order conversion has also been moved.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 9 Oct 2007 20:27:27 +0000 (13:27 -0700)]
[IPSEC]: Remove gratuitous km wake-up events on ACQUIRE
There is no point in waking people up when creating/updating larval states
because they'll just go back to sleep again as larval states by definition
cannot be found by xfrm_state_find.
We should only wake them up when the larvals mature or die.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 9 Oct 2007 20:25:59 +0000 (13:25 -0700)]
[IPSEC]: Store IPv6 nh pointer in mac_header on output
Current the x->mode->output functions store the IPv6 nh pointer in the
skb network header. This is inconvenient because the network header then
has to be fixed up before the packet can leave the IPsec stack. The mac
header field is unused on output so we can use that to store this instead.
This patch does that and removes the network header fix-up in xfrm_output.
It also uses ipv6_hdr where appropriate in the x->type->output functions.
There is also a minor clean-up in esp4 to make it use the same code as
esp6 to help any subsequent effort to merge the two.
Lastly it kills two redundant skb_set_* statements in BEET that were
simply copied over from transport mode.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 9 Oct 2007 20:24:07 +0000 (13:24 -0700)]
[IPSEC]: Remove bogus ref count in xfrm_secpath_reject
Constructs of the form
xfrm_state_hold(x);
foo(x);
xfrm_state_put(x);
tend to be broken because foo is either synchronous where this is totally
unnecessary or if foo is asynchronous then the reference count is in the
wrong spot.
In the case of xfrm_secpath_reject, the function is synchronous and therefore
we should just kill the reference count.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Tue, 9 Oct 2007 20:02:17 +0000 (13:02 -0700)]
[NETNS]: Don't memset() netns to zero manually
The newly created net namespace is set to 0 with memset()
in setup_net(). The setup_net() is also called for the
init_net_ns(), which is zeroed naturally as a global var.
So remove this memset and allocate new nets with the
kmem_cache_zalloc().
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Thery [Tue, 9 Oct 2007 03:39:36 +0000 (20:39 -0700)]
[IPv6]: use container_of() macro in fib6_clean_node()
In ip6_fib.c, fib6_clean_node() casts a fib6_walker_t pointer to
a fib6_cleaner_t pointer assuming a struct fib6_walker_t (field 'w')
is the first field in struct fib6_walker_t.
To prevent any future problems that may occur if one day a field
is inadvertently inserted before the 'w' field in struct fib6_cleaner_t,
(and to improve readability), this patch uses the container_of() macro.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Tue, 9 Oct 2007 03:38:39 +0000 (20:38 -0700)]
[NETNS]: Move some code into __init section when CONFIG_NET_NS=n
With the net namespaces many code leaved the __init section,
thus making the kernel occupy more memory than it did before.
Since we have a config option that prohibits the namespace
creation, the functions that initialize/finalize some netns
stuff are simply not needed and can be freed after the boot.
Currently, this is almost not noticeable, since few calls
are no longer in __init, but when the namespaces will be
merged it will be possible to free more code. I propose to
use the __net_init, __net_exit and __net_initdata "attributes"
for functions/variables that are not used if the CONFIG_NET_NS
is not set to save more space in memory.
The exiting functions cannot just reside in the __exit section,
as noticed by David, since the init section will have
references on it and the compilation will fail due to modpost
checks. These references can exist, since the init namespace
never dies and the exit callbacks are never called. So I
introduce the __exit_refok attribute just like it is already
done with the __init_refok.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Tue, 9 Oct 2007 03:28:47 +0000 (20:28 -0700)]
[8021Q]: transfer dev_id from real device
A net_device struct provides field dev_id. It is used for
unique ipv6 generation in case of shared network cards
(as for the OSA network cards of IBM System z).
If VLAN devices are built on top of such shared network cards,
this dev_id information needs to be transferred to the VLAN device.
Signed-off-by: Ursula Braun <braunu@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 9 Oct 2007 00:25:53 +0000 (17:25 -0700)]
[IPSEC]: Move output replay code into xfrm_output
The replay counter is one of only two remaining things in the output code
that requires a lock on the xfrm state (the other being the crypto). This
patch moves it into the generic xfrm_output so we can remove the lock from
the transforms themselves.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 9 Oct 2007 00:16:30 +0000 (17:16 -0700)]
[IPSEC]: Move common output code to xfrm_output
Most of the code in xfrm4_output_one and xfrm6_output_one are identical so
this patch moves them into a common xfrm_output function which will live
in net/xfrm.
In fact this would seem to fix a bug as on IPv4 we never reset the network
header after a transform which may upset netfilter later on.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 9 Oct 2007 00:14:34 +0000 (17:14 -0700)]
[IPSEC] ah: Remove keys from ah_data structure
The keys are only used during initialisation so we don't need to carry them
in esp_data. Since we don't have to allocate them again, there is no need
to place a limit on the authentication key length anymore.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 9 Oct 2007 00:13:44 +0000 (17:13 -0700)]
[IPSEC] esp: Remove keys from esp_data structure
The keys are only used during initialisation so we don't need to carry them
in esp_data. Since we don't have to allocate them again, there is no need
to place a limit on the authentication key length anymore.
This patch also kills the unused auth.icv member.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Mon, 8 Oct 2007 09:03:31 +0000 (02:03 -0700)]
[AF_IUCV]: postpone receival of iucv-packets
AF_IUCV socket programs may waste Linux storage, because af_iucv
allocates an skb whenever posted by the receive callback routine and
receives the message immediately.
Message receival is now postponed if data from previous callbacks has
not yet been transferred to the receiving socket program. Instead a
message handle is saved in a message queue as a reminder. Once
messages could be given to the receiving socket program, there is
an additional checking for entries in the message queue, followed
by skb allocation and message receival if applicable.
Signed-off-by: Ursula Braun <braunu@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiko Carstens [Mon, 8 Oct 2007 09:02:52 +0000 (02:02 -0700)]
[AF_IUCV]: remove static declarations from header file.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Ursula Braun <braunu@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Honor the advertisement bitmask from ethtool. We used to always
advertise the full capability when autoneg was set to on.
changed things around so that ethtool speed settings were strictly
followed. Unfortunately ethtool doesn't seem to set ADVERTISED_Autoneg
in the advertising field (and maybe it shouldn't have to). I'd vote
that it should be fixed there, but it should also be added here just in
case someone using ethtool ioctls in their own application gets what
they want.
Adding that flag in tg3_set_settings seemed like the most logical place
since the driver works fine on boot. This is just an issue when
re-enabling autonegotiation, so we should probably nip it there.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Acked-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a kernel oops triggered by the ksdazzle SIR driver.
We need more space for input frames, and 2048 should be plenty of it.
Signed-off-by: Alex VillacÃs Lasso <a_villacis@palosanto.com> Signed-off-by: Samuel Ortiz <samuel@sortiz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Garzik [Mon, 8 Oct 2007 07:06:32 +0000 (00:06 -0700)]
[NET]: split dev_ifsioc() according to locking
This always bugged me: dev_ioctl() called dev_ifsioc() either inside
read_lock(dev_base_lock) or rtnl_lock(), depending on the ioctl being
executed.
This change moves the ioctls executed inside dev_base_lock to a new
function, dev_ifsioc_locked(). Now the locking context is completely
clear to the reader.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bunch of sparse warnings. Mostly about 0 used as
NULL pointer, and shadowed variable declarations.
One notable case was that hash size should have been unsigned.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Mon, 8 Oct 2007 06:36:41 +0000 (23:36 -0700)]
[TCP]: Fix two off-by-one errors in fackets_out adjusting logic
1) Passing wrong skb to tcp_adjust_fackets_out could corrupt
fastpath_cnt_hint as tcp_skb_pcount(next_skb) is not included
to it if hint points exactly to the next_skb (it's lagging
behind, see sacktag).
2) When fastpath_skb_hint is put backwards to avoid dangling
skb reference, the skb's pcount must also be removed from count
(not included like above).
Reported by Cedric Le Goater <legoater@free.fr>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Mon, 8 Oct 2007 06:28:35 +0000 (23:28 -0700)]
[TG3]: Add 5784 and 5764 support.
This patch adds the support for 5784 and 5764 devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Mon, 8 Oct 2007 06:28:17 +0000 (23:28 -0700)]
[TG3]: ASIC decoding and basic CPMU support.
Newer products change the way the ASIC revision is obtained. This patch
implements how the driver will extract the revision number.
This patch also adds preliminary CPMU support. CPMU stands for Central
Power Management Unit. The CPMU's role is to put the chip into lower
power states when the operating conditions allow it.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Mon, 8 Oct 2007 06:27:28 +0000 (23:27 -0700)]
[TG3]: Walk PCI capability lists.
Newer tg3 devices shuffle around the registers in PCI configuration
space. This patch changes the way the driver accesses the PCI
capabilities registers. Hardcoded register locations are replaced with
offsets from pci_find_capability() return values.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Auke Kok [Thu, 4 Oct 2007 22:00:08 +0000 (15:00 -0700)]
e1000e: Fix ethtool register test code
A merge/cleanup code accidentally dropped 8254x code in and removed
8257x code here. Undo this mistake and use the pci-e relevant register
test similar as to what is in e1000.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Klaus D. Wacker [Fri, 5 Oct 2007 14:45:47 +0000 (16:45 +0200)]
lcs: Channel errors drive lcs_recovery which leads to kernel panic.
When the lcs irq routine detects channel failures it drives device recovery.
After this event the device is no longer usable for shutdown requests,
because the lcs_irq routine may get wrong channel status information.
In such a case the lcs_irq routine marks the channel in 'error' state.
The channel state comes back to 'running' after restarting the channels.
Signed-off-by: Klaus D. Wacker <kdwacker@de.ibm.com> Signed-off-by: Ursula Braun <braunu@de.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ursula Braun [Fri, 5 Oct 2007 14:45:46 +0000 (16:45 +0200)]
qeth: avoid duplicate deletion of multicast addresses
if qeth_set_multicast_list() is performed on 2 CPUs in parallel,
card->ip_list may end corrupted.
Solution: In function __qeth_delete_all_mc()
remove card->ip_list entry before invoking
qeth_deregister_addr_entry(). Thus a 2nd invocation of
qeth_set_multicast_list() cannot try to remove the
same entry twice.
Klaus D. Wacker [Fri, 5 Oct 2007 14:45:44 +0000 (16:45 +0200)]
qeth: HiperSockets layer-3 interface drop non IPv4 or non IPv6 packets
HiperSockets infrastructure (layer-3 mode) supports only IPv4 or
IPv6 packets. Sending other packet types disturbs TCP/IP on z/VM,
which issues messages about invalid packets.
Qeth send routine will detect packet type on sending over a
HiperSockets interface (in layer-3 mode) and drop non IP packets.
The error and drop count of the interface is incremented.
Signed-off-by: Klaus D. Wacker <kdwacker@de.ibm.com> Signed-off-by: Ursula Braun <braunu@de.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Gerrit Renker [Thu, 4 Oct 2007 21:52:28 +0000 (14:52 -0700)]
[DCCP]: Twice the wrong reset code in receiving connection-Requests
This fixes two bugs in processing of connection-Requests in
v{4,6}_conn_request:
1. Due to using the variable `reset_code', the Reset code generated
internally by dccp_parse_options() is overwritten with the
initialised value ("Too Busy") of reset_code, which is not what is
intended.
2. When receiving a connection-Request on a multicast or broadcast
address, no Reset should be generated, to avoid storms of such
packets. Instead of jumping to the `drop' label, the
v{4,6}_conn_request functions now return 0. Below is why in my
understanding this is correct:
When the conn_request function returns < 0, then the caller,
dccp_rcv_state_process(), returns 1. In all instances where
dccp_rcv_state_process is called (dccp_v4_do_rcv, dccp_v6_do_rcv,
and dccp_child_process), a return value of != 0 from
dccp_rcv_state_process() means that a Reset is generated.
If on the other hand the conn_request function returns 0, the
packet is discarded and no Reset is generated.
Note: There may be a related problem when sending the Response, due to
the following.
In this case, if send_response fails due to transmission errors, the
next thing that is generated is a Reset with a code "Too Busy". I
haven't been able to conjure up such a condition, but it might be good
to change the behaviour here also (not done by this patch).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gerrit Renker [Thu, 4 Oct 2007 21:50:57 +0000 (14:50 -0700)]
[DCCP]: Correct documentation
This corrects erroneous documentation of the socket API.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gerrit Renker [Thu, 4 Oct 2007 21:43:42 +0000 (14:43 -0700)]
[DCCP]: Tidy-up -- minisock initialisation
This
* removes a declaration of a non-existent function
__dccp_minisock_init;
* shifts the initialisation function dccp_minisock_init() from
options.c to minisocks.c, where it is more naturally expected to
be.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gerrit Renker [Thu, 4 Oct 2007 21:43:09 +0000 (14:43 -0700)]
[CCID2]: Sequence number wraparound issues
This replaces several uses of standard arithmetic with the DCCP
sequence number arithmetic functions. The problem here is that the
sequence number wrap-around was not taken into consideration.
* Condition "seqp->ccid2s_seq <= prev->ccid2s_seq" has been replaced
by
since if seqp is `before' prev, then the delta_seqno() is positive.
* The test whether sequence numbers `a' and `b' are consecutive has
the form
dccp_delta_seqno(a, b) == 1
* Increment of ccid2hctx_rpseq could be done using dccp_inc_seqno(),
but since here the incremented ccid2hctx_rpseq == seqno, used
assignment instead.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gerrit Renker [Thu, 4 Oct 2007 21:42:19 +0000 (14:42 -0700)]
[CCID2]: Remove redundant case block
skb's passed to ccid2_hc_tx_send_packet() are headerless, the packet
type is decided later, in dccp_write_xmit(). Therefore the first test
of the switch/case block is always true, the others are never reached.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gerrit Renker [Thu, 4 Oct 2007 21:41:55 +0000 (14:41 -0700)]
[CCID2]: Remove redundant BUG_ON
This removes a test for `val < 1' which would only have been triggered
when val < 0, due to a preceding test for 0. Fixed by using an
unsigned type for cwnd (as in TCP) instead.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gerrit Renker [Thu, 4 Oct 2007 21:41:26 +0000 (14:41 -0700)]
[CCID2]: Remove ugly BUG_ON
This removes an ugly BUG_ON which has been pointed out by Arnaldo.
Instead of freezing up the machine, a `critical' message is now issued
to the system log.
There is potential of doing this more gracefully (eg. there are a few
internal variables which could be updated despite the lack of memory),
but that requires more complicated changes to the algorithm; thus a
`FIXME' has been added.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gerrit Renker [Thu, 4 Oct 2007 21:41:00 +0000 (14:41 -0700)]
[CCID2]: Simplify interface
This patch simplifies the interface of ccid2_hc_tx_alloc_seq():
* ccid2_hc_tx_alloc_seq() is always called with an argument of
CCID2_SEQBUF_LEN;
* other code - ccid2_hc_tx_check_sanity() - even depends on the
assumption that ccid2_hc_tx_alloc_seq() has been called with this
particular size;
* passing the `gfp_t' argument to ccid2_hc_tx_alloc_seq() is
redundant with gfp_any().
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gerrit Renker [Thu, 4 Oct 2007 21:40:22 +0000 (14:40 -0700)]
[DCCP]: Update API documentation
This adds documentation on the use of service codes on client and
server.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gerrit Renker [Thu, 4 Oct 2007 21:39:53 +0000 (14:39 -0700)]
[DCCP]: Make all `debug' parameters bool
This just sets the parameter to bool, since debugging messages are
either on or off.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gerrit Renker [Thu, 4 Oct 2007 21:39:22 +0000 (14:39 -0700)]
[DCCP]: Add socket option to query the current MPS
This enables applications to query the current value of the Maximum
Packet Size via a socket option, suggested as a SHOULD in (RFC 4340,
p. 102).
This socket option is useful to avoid the annoying bail-out via
`-EMSGSIZE'. In particular, as fragmentation is not currently
supported (and its use is partly discouraged in RFC 4340).
With this option, it is possible to size buffers accordingly, e.g.
int buflen = dccp_get_cur_mps(sockfd);
/* or */
if (msgsize > dccp_get_cur_mps(sockfd))
die("message is too large for this path");
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gerrit Renker [Thu, 4 Oct 2007 21:38:49 +0000 (14:38 -0700)]
[DCCP]: Wait for CCID
This performs a minor optimisation: when ccid_hc_tx_send_packet
returns a value greater zero, then the same call previously was done
again at the begin of the while loop in dccp_wait_for_ccid.
This patch exploits the available information and schedule-timeouts
directly instead.
Documentation also added.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
sp->txd_map is an u64
because :
dma_addr_t txd_map;
And in asm-i386/types.h, I see :
#ifdef CONFIG_HIGHMEM64G
typedef u64 dma_addr_t;
#else
typedef u32 dma_addr_t;
#endif
I my config, I use CONFIG_HIGHMEM64G
sizeof(struct ipg_tx) is an u32
So the div failed on i386 because of u64 / u32.
[akpm@linux-foundation.org: cleanups] Cc: Sorbica Shieh <sorbica@icplus.com.tw> Cc: Jesse Huang <jesse@icplus.com.tw> Cc: Jeff Garzik <jeff@garzik.org> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Olof Johansson [Tue, 2 Oct 2007 21:27:57 +0000 (16:27 -0500)]
pasemi_mac: use buffer index pointer in clean_rx()
pasemi_mac: use buffer index pointer in clean_rx()
Use the new features in B0 for buffer ring index on the receive side. This
means we no longer have to search in the ring for where the buffer
came from.
Also cleanup the RX cleaning side a little, while I was at it.
Note: Pre-B0 hardware is no longer supported, and needs a pile of other
workarounds that are not being submitted for mainline inclusion. So the
fact that this breaks old hardware is not a problem at this time.
Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Olof Johansson [Tue, 2 Oct 2007 21:27:39 +0000 (16:27 -0500)]
pasemi_mac: clear out old errors on interface open
pasemi_mac: clear out old errors on interface open
Clear out any pending errors when an interface is brought up. Since the bits
are sticky, they might be from interface shutdown time after firmware has
used it, etc.
Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Olof Johansson [Tue, 2 Oct 2007 21:27:15 +0000 (16:27 -0500)]
pasemi_mac: further performance tweaks
pasemi_mac: further performance tweaks
Misc driver tweaks for pasemi_mac:
* Increase ring size (really needed mostly on 10G)
* Take out an unneeded barrier
* Move around a few prefetches and reorder a few calls
* Don't try to clean on full tx buffer, just let things
take their course and stop the queue directly
* Avoid filling on the same line as the interface is
working on to reduce cache line bouncing
* Avoid unneeded clearing of software state (and make the
interface shutdown code handle it)
* Fix up some of the tx ring wrap logic.
Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Olof Johansson [Tue, 2 Oct 2007 21:26:53 +0000 (16:26 -0500)]
pasemi_mac: add local skb alignment
pasemi_mac: add local skb alignment
Add local SKB alignment to pasemi_mac, since ppc64 in general has it at 0
because of design flaws in some of the IBM server bridge chips. However,
for PWRficient doing the unaligned copies is more expensive than doing
unaligned DMA so make sure the data is aligned instead.
Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Olof Johansson [Tue, 2 Oct 2007 21:26:30 +0000 (16:26 -0500)]
pasemi_mac: workaround for erratum 5971
pasemi_mac: workaround for erratum 5971
Implement workarounds for erratum 5971, where L2 hints aren't considered
properly unless the way hint is enabled on the interface. Since L2 isn't
setup to dedicate a way to headers, we need to reset the packet count
by hand so it won't run out of credits.
Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Olof Johansson [Tue, 2 Oct 2007 21:25:53 +0000 (16:25 -0500)]
pasemi_mac: rework ring management
pasemi_mac: rework ring management
Rework ring management, switching to an opaque ring format instead of
the struct-based descriptor+pointer setup, since it will be needed for
SG support.
Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tomas Winkler [Sun, 30 Sep 2007 11:52:37 +0000 (13:52 +0200)]
[MAC80211]: add sta_notify callback
This patch adds sta_notify callback and removes sta_table_notification
which was not used by any driver.
sta_notify() is essential for drivers that keeps notion of station
internally and need to be notified about removal or addition of a station
to the (I)BSS or assocation to an AP.
This version adds interface id to the parameter list
as suggested by Johannes Berg
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This implements the cfg80211 change_interface hook that changes the
type of an interface and cleans up the code a bit.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Buesch [Thu, 27 Sep 2007 13:10:44 +0000 (15:10 +0200)]
[MAC80211]: Add association LED trigger
Many devices have LEDs to indicate the link status.
Export this functionality to drivers.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Wed, 26 Sep 2007 15:53:20 +0000 (17:53 +0200)]
[MAC80211]: make userspace-mlme a per-interface setting
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Wed, 26 Sep 2007 15:53:18 +0000 (17:53 +0200)]
[MAC80211]: improve radiotap injection
This improves radiotap injection by removing the shortcut over TX handlers
that led to BUGS when injecting frames without setting a rate and also
resulted in various other quirks. Now, TX handlers are run but some
information that was present in the radiotap header is used instead of
automatic settings.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: Andy Green <andy@warmcat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 26 Sep 2007 15:53:17 +0000 (17:53 +0200)]
[MAC80211]: remove ALG_NONE
This "algorithm" is used only internally and is not useful.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: Michael Buesch <mb@bu3sch.de> Acked-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Wed, 26 Sep 2007 15:53:16 +0000 (17:53 +0200)]
[MAC80211]: use RX_FLAG_DECRYPTED for sw decrypted as well
This makes mac80211 set the RX_FLAG_DECRYPTED flag for frames
decrypted in software allowing us to handle some things more
uniformly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Wed, 26 Sep 2007 15:53:15 +0000 (17:53 +0200)]
[MAC80211]: consolidate decryption more
Currently, we have three RX handlers doing the decryption.
This patch changes it to have only one handler doing
everything, thereby getting rid of many duplicate checks.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
--
net/mac80211/rx.c | 46 ++++++++++++----------------------------------
1 files changed, 12 insertions(+), 34 deletions(-)
Johannes Berg [Wed, 26 Sep 2007 15:53:14 +0000 (17:53 +0200)]
[MAC80211]: move sta_process rx handler later
This moves the sta_process RX handler to after decryption
so that frames that cannot be decrypted don't influence
statistics, it is likely that they were injected or something
else is totally wrong.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Fri, 28 Sep 2007 12:02:09 +0000 (14:02 +0200)]
[MAC80211]: remove management interface
Removes the management interface since it is only required
for hostapd/userspace MLME, will not be in the final tree
at least in this form and hostapd/userspace MLME currently
do not work against this tree anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Fri, 28 Sep 2007 12:01:25 +0000 (14:01 +0200)]
[MAC80211]: add "invalid" interface type
Since I cannot convince the lazy driver authors (hello Michael)
to stop (ab)using the MGMT interface type internally in their
drivers, this patch introduces a new _INVALID type especially
for their use and changes all affected drivers to use it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Buesch [Mon, 24 Sep 2007 16:41:49 +0000 (18:41 +0200)]
[MAC80211]: Check open_count before calling config callback.
Also remove the check for ops->config!=NULL, as it can never be NULL.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Buesch [Fri, 28 Sep 2007 14:19:03 +0000 (16:19 +0200)]
[B43]: Rewrite pwork locking policy.
Implement much easier and more lightweight locking for
the periodic work.
This also removes the last big busywait loop and replaces it
by a sleeping loop.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Buesch [Fri, 28 Sep 2007 12:22:33 +0000 (14:22 +0200)]
[B43]: Use input-polldev for the rfkill switch
This removes the direct call to rfkill on an rfkill event
and replaces it with an input device. This way userspace is also
notified about the event.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Buesch [Thu, 27 Sep 2007 19:35:34 +0000 (21:35 +0200)]
[B43]: RF-kill support
This adds full support for the RFKILL button and
the RFKILL LED trigger.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Buesch [Thu, 27 Sep 2007 13:31:40 +0000 (15:31 +0200)]
[B43]: LED triggers support
Drive the LEDs through the generic LED triggers.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Cc: Larry Finger <larry.finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6 / log