Alan Stern [Tue, 20 Dec 2005 14:58:08 +0000 (09:58 -0500)]
[PATCH] UHCI: Don't log short transfers
Even when the URB_SHORT_NOT_OK flag is set, a short transfer shouldn't
generate a debugging log message. Especially not one with the confusing
claim that the transfer "failed with status 0". This patch (as627)
fixes that behavior in uhci-hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Sat, 17 Dec 2005 23:03:37 +0000 (18:03 -0500)]
[PATCH] UHCI: improve debugging code
This patch (as626) makes some improvements to the debugging code in
uhci-hcd. The main change is that now the code won't get compiled if
CONFIG_USB_DEBUG isn't set. But there are other changes too, like
adding a missing .owner field and printing a debugging dump if the
controller dies.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Sat, 17 Dec 2005 23:02:38 +0000 (18:02 -0500)]
[PATCH] UHCI: remove main list of URBs
As part of reorienting uhci-hcd away from URBs and toward endpoint
queues, this patch (as625) eliminates the driver's main list of URBs.
The list wsa used mainly in checking for URB completions; now the driver
goes through the list of active endpoints and checks the members of the
queues.
As a side effect, I had to remove the code that looks for FSBR timeouts.
For now, FSBR will remain on so long as any URBs on a full-speed control
or bulk queue request it, even if the queue isn't advancing. A later
patch can add more intelligent handling. This isn't a huge drawback;
it's pretty rare for an URB to get stuck for more than a fraction of a
second. (And it will help the people trying to use those insane HP USB
devices.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Sat, 17 Dec 2005 23:00:12 +0000 (18:00 -0500)]
[PATCH] UHCI: use dummy TDs
This patch (as624) fixes a hardware race in uhci-hcd by adding a dummy
TD to the end of each endpoint's queue. Without the dummy the host
controller will effectively turn off the queue when it reaches the end,
which happens asynchronously. This leads to a potential problem when
new transfer descriptors are added to the end of the queue; they may
never get used.
With a dummy TD present the controller never turns off the queue;
instead it just stops at the dummy and leaves the queue on but inactive.
When new TDs are added to the end of the queue, the first new one gets
written over the dummy. Thus there's never any question about whether
the queue is running or needs to be restarted.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Sat, 17 Dec 2005 22:58:46 +0000 (17:58 -0500)]
[PATCH] UHCI: use one QH per endpoint, not per URB
This patch (as623) changes the uhci-hcd driver to make it use one QH per
device endpoint, instead of a QH per URB as it does now. Numerous areas
of the code are affected by this. For example, the distinction between
"queued" URBs and non-"queued" URBs no longer exists; all URBs belong to
a queue and some just happen to be at the queue's head.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Furthermore it replaces all LINKSYS_GPIO_RESET with DEFAULT_GPIO_RESET as both
are declared like this:
#define DEFAULT_GPIO_RESET 0x24
#define LINKSYS_GPIO_RESET 0x24
This is misleading and confusing.
The check is now done via the VENDOR_ID in pegasus.c:
if (usb_dev_id[pegasus->dev_index].vendor == VENDOR_LINKSYS
Alan Stern [Tue, 31 Jan 2006 17:58:38 +0000 (12:58 -0500)]
[PATCH] usbhid: add error handling
This patch (as628c) adds error handling to the USB HID core. When an
error is reported for an interrupt URB, the driver will do delayed
retries, at increasing intervals, for up to one second. If that doesn't
work, it will try to reset the device. Testing by users has shown that
both the retries and the resets end up getting used.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Tue, 24 Jan 2006 16:40:27 +0000 (08:40 -0800)]
[PATCH] USB: remove usbcore-specific wakeup flags
This makes usbcore use the driver model wakeup flags for host controllers
and for their root hubs. Since previous patches have removed all users of
the HCD flags they replace, this converts the last users of those flags.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Mon, 23 Jan 2006 23:28:07 +0000 (15:28 -0800)]
[PATCH] USB: ohci uses driver model wakeup flags
This makes OHCI use the driver model wakeup control bits for its root hub
(e.g. disable on amd756, because of chip erratum) and for the controller
itself. It no longer uses the hcd glue bits with those roles, and depends
on the previous patch making the root hub available earlier.
Note that on most platforms (boot code properly setting the RWC bit) this
gives a partial workaround for the way PCI isn't currently flagging devices
that support PME# signals. (Because of odd PCI init sequencing on PPC.)
That's because many OHCI controllers support "legacy PCI PM" ... without
involving any PCI PM capability.
USB wakeup from STR, if it works on your system, may still involve
tweaking things by hand in /proc/acpi/wakeup.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Mon, 23 Jan 2006 23:25:40 +0000 (15:25 -0800)]
[PATCH] USB: usbcore sets up root hubs earlier
Make the HCD initialization sequence more sane ... notably, setting up
root hubs before HCDs are asked to do their one-time init. Among other
things, that lets the HCDs do custom root hub init along with all the
other one-time initialization done in the (now misnamed) reset() method.
This also copies the controller wakeup flags into the root hub; it's
done a bit later than would be ideal, but that'll be necessary until
the PCI code initializes them correctly. (The PCI patch breaks on PPC
due to how it sequences PCI initialization.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Sun, 22 Jan 2006 18:32:37 +0000 (10:32 -0800)]
[PATCH] USB: add support for AT91 gadget
This adds support for the USB peripheral controller on AT91
(rm9200, eventually also sam9261 or uClinux) platforms.
More SOC support for Linux-USB ... an uncomplicated pure PIO driver.
It'd be worth using this as a model, if you're starting a driver
for some other peripheral controller.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Andrew Victor [Sun, 22 Jan 2006 18:32:13 +0000 (10:32 -0800)]
[PATCH] USB: add support for OCHI on AT91rm9200
This adds support for OHCI on AT91rm9200 based boards.
Possibly of interest here is the way this uses <linux/clk.h> to
gate clocks on/off during system pm state transitions. That's
typical for non-PCI systems. Some can go further; Mini-A host
side connectors enable ID-pin sensing.
From: Andrew Victor <andrew@sanpeople.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Fri, 20 Jan 2006 22:35:55 +0000 (14:35 -0800)]
[PATCH] USB: EHCI unlink tweaks
This patch modifies the behavior of the EHCI driver in an unlink path
that seems to be causing various issues on some systems. Those problems
have included issues with disconnection, driver unbinding, and similar
cases where urb unlinking would just not work right.
This patch should help avoid those problems by not turning off the async
(control/bulk) schedule until it's not expecting an "async advance" IRQ,
which comes from the processing passing the schedule head. Whether the
driver attempts to do such things is dependent on system timings, so
many folk would never have seen these problems.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kumar Gala [Fri, 20 Jan 2006 21:57:52 +0000 (13:57 -0800)]
[PATCH] USB: EHCI and Freescale 83xx quirk
On the MPC834x processors the multiport host (MPH) EHCI controller has an
erratum in which the port number in the queue head expects to be 0..N-1
instead of 1..N. If we are on one of these chips we subtract one from
the port number before putting it into the queue head.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Randy Vinson [Fri, 20 Jan 2006 21:53:38 +0000 (13:53 -0800)]
[PATCH] USB: EHCI for Freescale 83xx
Adding a Host Mode USB driver for the Freescale 83xx.
This driver supports both the Dual-Role (DR) controller and the
Multi-Port-Host (MPH) controller present in the Freescale MPC8349. It has
been tested with the MPC8349CDS reference system. This driver depends on
platform support code for setting up the pins on the device package in a
manner appropriate for the board in use. Note that this patch requires
selecting the EHCI controller option under the USB Host menu.
Signed-off-by: Randy Vinson <rvinson@mvista.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clemens Ladisch [Fri, 20 Jan 2006 21:49:10 +0000 (13:49 -0800)]
[PATCH] USB: EHCI full speed ISO bugfixes
This patch replaces the split ISO raw_mask calculation code in the
iso_stream_init() function that computed incorrect numbers of high
speed transactions for both input and output transfers.
In the output case, it added a superfluous start-split transaction for
all maxmimum packet sizes that are a multiple of 188.
In the input case, it forgot to add complete-split transactions for all
microframes covered by the full speed transaction, and the additional
complete-split transaction needed for the case when full speed data
starts arriving near the end of a microframe.
These changes don't affect the lack of full speed bandwidth, but at
least it removes the MMF errors that the HC raised with some input
streams.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Fri, 20 Jan 2006 21:55:14 +0000 (13:55 -0800)]
[PATCH] USB: EHCI and NF2 quirk
This teaches the EHCI driver about a quirk seen in older NForce2 chips,
adding a workaround to ignore selective suspend requests. Bus-wide
(so-called "global") suspend still works, as does USB wakeup of a
root hub that's globally suspended.
There's still a hole in this support though. Strictly speaking, this
should _fail_ selective suspend requests, rather than ignoring them,
since doing it this way means that devices which should be able to issue
remote wakeup are not going to be able to do that. For now, we'll just
live with that problem ... since usbcore expects to do selective suspend
on the way towards a full bus suspend, and usbcore needs to be able to
do full bus suspend.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Andrew Morton [Thu, 19 Jan 2006 07:55:07 +0000 (23:55 -0800)]
[PATCH] USB: optimise devio.c usbdev_read fix
drivers/usb/core/devio.c: In function `usbdev_read':
drivers/usb/core/devio.c:140: error: invalid type argument of `->'
drivers/usb/core/devio.c:141: error: invalid type argument of `->'
drivers/usb/core/devio.c:142: error: invalid type argument of `->'
drivers/usb/core/devio.c:143: error: invalid type argument of `->'
Cc: Oliver Neukum <oliver@neukum.org> Cc: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: (230 commits)
[SPARC64]: Update defconfig.
[SPARC64]: Fix 2 bugs in huge page support.
[SPARC64]: CONFIG_BLK_DEV_RAM fix
[SPARC64]: Optimized TSB table initialization.
[SPARC64]: Allow CONFIG_MEMORY_HOTPLUG to build.
[SPARC64]: Use SLAB caches for TSB tables.
[SPARC64]: Don't kill the page allocator when growing a TSB.
[SPARC64]: Randomize mm->mmap_base when PF_RANDOMIZE is set.
[SPARC64]: Increase top of 32-bit process stack.
[SPARC64]: Top-down address space allocation for 32-bit tasks.
[SPARC64] bbc_i2c: Fix cpu check and add missing module license.
[SPARC64]: Fix and re-enable dynamic TSB sizing.
[SUNSU]: Fix missing spinlock initialization.
[TG3]: Do not try to access NIC_SRAM_DATA_SIG on Sun parts.
[SPARC64]: First cut at VIS simulator for Niagara.
[SPARC64]: Fix system type in /proc/cpuinfo and remove bogus OBP check.
[SPARC64]: Add SMT scheduling support for Niagara.
[SPARC64]: Fix 32-bit truncation which broke sparsemem.
[SPARC64]: Move over to sparsemem.
[SPARC64]: Fix new context version SMP handling.
...
Linus Torvalds [Mon, 20 Mar 2006 18:32:33 +0000 (10:32 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/shaggy/jfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/shaggy/jfs-2.6:
JFS: add uid, gid, and umask mount options
JFS: Take logsync lock before testing mp->lsn
JFS: kzalloc conversion
JFS: Add missing file from fa3241d24cf1182b0ffb6e4d412c3bc2a2ab7bf6
JFS: Use the kthread_ API
JFS: Fix regression. fsck complains if symlinks do not have INLINEEA attribute
JFS: ext2 inode attributes for jfs
JFS: semaphore to mutex conversion.
JFS: make buddy table static
JFS: Add back directory i_size calculations for legacy partitions
Linus Torvalds [Mon, 20 Mar 2006 18:30:31 +0000 (10:30 -0800)]
Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (150 commits)
[PATCH] ipw2100: Update version ipw2100 stamp to 1.2.2
[PATCH] ipw2100: move mutex.h include from ipw2100.c to ipw2100.h
[PATCH] ipw2100: semaphore to mutexes conversion
[PATCH] ipw2100: Fix radiotap code gcc warning
[PATCH] ipw2100: add radiotap headers to packtes captured in monitor mode
[PATCH] ipw2x00: expend Copyright to 2006
[PATCH] drivers/net/wireless/ipw2200.c: fix an array overun
[PATCH] ieee80211: Don't update network statistics from off-channel packets.
[PATCH] ipw2200: Update ipw2200 version stamp to 1.1.1
[PATCH] ipw2200: switch to the new ipw2200-fw-3.0 image format
[PATCH] ipw2200: wireless extension sensitivity threshold support
[PATCH] ipw2200: Enables the "slow diversity" algorithm
[PATCH] ipw2200: Set a meaningful silence threshold value
[PATCH] ipw2200: export `debug' module param only if CONFIG_IPW2200_DEBUG
[PATCH] ipw2200: Change debug level for firmware error logging
[PATCH] ipw2200: Filter unsupported channels out in ad-hoc mode
[PATCH] ipw2200: Fix ipw_sw_reset() implementation inconsistent with comment
[PATCH] ipw2200: Fix rf_kill is activated after mode change with 'disable=1'
[PATCH] ipw2200: remove the WPA card associates to non-WPA AP checking
[PATCH] ipw2200: Add signal level to iwlist scan output
...
Linus Torvalds [Mon, 20 Mar 2006 18:28:51 +0000 (10:28 -0800)]
Merge branch 'block-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/block
* 'block-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/block:
[PATCH] fix rmmod problems with elevator attributes, clean them up
[PATCH] elevator_t lifetime rules and sysfs fixes
[PATCH] noise removal: cfq-iosched.c
[PATCH] don't bother with refcounting for cfq_data
[PATCH] fix sysfs interaction and lifetime rules handling for queues
[PATCH] regularize blk_cleanup_queue() use
[PATCH] fix cfq_get_queue()/ioprio_set(2) races
[PATCH] deal with rmmod/put_io_context() races
[PATCH] stop elv_unregister() from rogering other iosched's data, fix locking
[PATCH] stop cfq from pinning queue down
[PATCH] make cfq_exit_queue() prune the cfq_io_context for that queue
[PATCH] fix the exclusion for ioprio_set()
[PATCH] keep sync and async cfq_queue separate
[PATCH] switch to use of ->key to get cfq_data by cfq_io_context
[PATCH] stop leaking cfq_data in cfq_set_request()
[PATCH] fix cfq hash lookups
[PATCH] fix locking in queue_requests_store()
[PATCH] fix double-free in blk_init_queue_node()
[PATCH] don't do exit_io_context() until we know we won't be doing any IO
David S. Miller [Sun, 19 Mar 2006 07:55:11 +0000 (23:55 -0800)]
[SPARC64]: Optimized TSB table initialization.
We only need to write an invalid tag every 16 bytes,
so taking advantage of this can save many instructions
compared to the simple memset() call we make now.
A prefetching implementation is implemented for sun4u
and a block-init store version if implemented for Niagara.
The next trick is to be able to perform an init and
a copy_tsb() in parallel when growing a TSB table.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 17 Mar 2006 22:41:03 +0000 (14:41 -0800)]
[SPARC64]: Top-down address space allocation for 32-bit tasks.
Currently allocations are very constrained for 32-bit processes.
It grows down-up from 0x70000000 to 0xf0000000 which gives about
2GB of stack + dynamic mmap() space.
So support the top-down method, and we need to override the
generic helper function in order to deal with D-cache coloring.
With these changes I was able to squeeze out a mmap() just over
3.6GB in size in a 32-bit process.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 16 Mar 2006 10:02:32 +0000 (02:02 -0800)]
[SPARC64]: Fix and re-enable dynamic TSB sizing.
This is good for up to %50 performance improvement of some test cases.
The problem has been the race conditions, and hopefully I've plugged
them all up here.
1) There was a serious race in switch_mm() wrt. lazy TLB
switching to and from kernel threads.
We could erroneously skip a tsb_context_switch() and thus
use a stale TSB across a TSB grow event.
There is a big comment now in that function describing
exactly how it can happen.
2) All code paths that do something with the TSB need to be
guarded with the mm->context.lock spinlock. This makes
page table flushing paths properly synchronize with both
TSB growing and TLB context changes.
3) TSB growing events are moved to the end of successful fault
processing. Previously it was in update_mmu_cache() but
that is deadlock prone. At the end of do_sparc64_fault()
we hold no spinlocks that could deadlock the TSB grow
sequence. We also have dropped the address space semaphore.
While we're here, add prefetching to the copy_tsb() routine
and put it in assembler into the tsb.S file. This piece of
code is quite time critical.
There are some small negative side effects to this code which
can be improved upon. In particular we grab the mm->context.lock
even for the tsb insert done by update_mmu_cache() now and that's
a bit excessive. We can get rid of that locking, and the same
lock taking in flush_tsb_user(), by disabling PSTATE_IE around
the whole operation including the capturing of the tsb pointer
and tsb_nentries value. That would work because anyone growing
the TSB won't free up the old TSB until all cpus respond to the
TSB change cross call.
I'm not quite so confident in that optimization to put it in
right now, but eventually we might be able to and the description
is here for reference.
This code seems very solid now. It passes several parallel GCC
bootstrap builds, and our favorite "nut cruncher" stress test which is
a full "make -j8192" build of a "make allmodconfig" kernel. That puts
about 256 processes on each cpu's run queue, makes lots of process cpu
migrations occur, causes lots of page table and TLB flushing activity,
incurs many context version number changes, and it swaps the machine
real far out to disk even though there is 16GB of ram on this test
system. :-)
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 9 Mar 2006 00:09:19 +0000 (16:09 -0800)]
[SPARC64]: Add SMT scheduling support for Niagara.
The mapping is a simple "(cpuid >> 2) == core" for now.
Later we'll add more sophisticated code that will walk
the sun4v machine description and figure this out from
there.
We should also add core mappings for jaguar and panther
processors.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 8 Mar 2006 23:57:03 +0000 (15:57 -0800)]
[SPARC64]: Fix 32-bit truncation which broke sparsemem.
The page->flags manipulations done by the D-cache dirty
state tracking was broken because the constants were not
marked with "UL" to make them 64-bit, which means we were
clobbering the upper 32-bits of page->flags all the time.
This doesn't jive well with sparsemem which stores the
section and indexing information in the top 32-bits of
page->flags.
This is yet another sparc64 bug which has been with us
forever.
While we're here, tidy up some things in bootmem_init()
and paginig_init():
1) Pass min_low_pfn to init_bootmem_node(), it's identical
to (phys_base >> PAGE_SHIFT) but we should use consistent
with the variable names we print in CONFIG_BOOTMEM_DEBUG
2) max_mapnr, although no longer used, was being set
inaccurately, we shouldn't subtract pfn_base any more.
3) All the games with phys_base in the zones_*[] arrays
we pass to free_area_init_node() are no longer necessary.
Thanks to Josh Grebe and Fabbione for the bug reports
and testing. Fix also verified locally on an SB2500
which had a memory layout that triggered the same problem.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 7 Mar 2006 06:50:44 +0000 (22:50 -0800)]
[SPARC64]: Fix new context version SMP handling.
Don't piggy back the SMP receive signal code to do the
context version change handling.
Instead allocate another fixed PIL number for this
asynchronous cross-call. We can't use smp_call_function()
because this thing is invoked with interrupts disabled
and a few spinlocks held.
Also, fix smp_call_function_mask() to count "cpus" correctly.
There is no guarentee that the local cpu is in the mask
yet that is exactly what this code was assuming.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 7 Mar 2006 03:59:50 +0000 (19:59 -0800)]
[SPARC64]: Bulletproof MMU context locking.
1) Always spin_lock_init() in init_context(). The caller essentially
clears it out, or copies the mm info from the parent. In both
cases we need to explicitly initialize the spinlock.
2) Always do explicit IRQ disabling while taking mm->context.lock
and ctx_alloc_lock.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 3 Mar 2006 05:50:47 +0000 (21:50 -0800)]
[SPARC64]: More SUN4V cpu mondo bug fixing.
This cpu mondo sending interface isn't all that easy to
use correctly...
We were clearing out the wrong bits from the "mask" after getting
something other than EOK from the hypervisor.
It turns out the hypervisor can just be resent the same cpu_list[]
array, with the 0xffff "done" entries still in there, and it will do
the right thing.
So don't update or try to rebuild the cpu_list[] array to condense it.
This requires the "forward_progress" check to be done slightly
differently, but this new scheme is less bug prone than what we were
doing before.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 3 Mar 2006 02:12:27 +0000 (18:12 -0800)]
[SPARC64]: Do not allow mapping pages within 4GB of 64-bit VA hole.
The UltraSPARC T1 manual recommends this because the chip
could instruction prefetch into the VA hole, and this would
also make decoding certain kinds of memory access traps
more difficult (because the chip sign extends certain pieces
of trap state).
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 2 Mar 2006 06:42:18 +0000 (22:42 -0800)]
[SPARC64]: Fix _PAGE_EXEC handling.
First of all, use the known _PAGE_EXEC_{4U,4V} value instead
of loading _PAGE_EXEC from memory. We either know which one
to use by context, or we can code patch the test.
Next, we need to check executability of a PTE in the generic
TSB miss handler.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 28 Feb 2006 23:10:26 +0000 (15:10 -0800)]
[SPARC64]: Fix bugs in SUN4V cpu mondo dispatch.
There were several bugs in the SUN4V cpu mondo dispatch code.
In fact, if we ever got a EWOULDBLOCK or other error from
the hypervisor call, we'd potentially send a cpu mondo multiple
times to the same cpu and even worse we could loop until the
timeout resending the same mondo over and over to such cpus.
So let's bulletproof this thing as follows:
1) Implement cpu_mondo_send() and cpu_state() hypervisor calls
in arch/sparc64/kernel/entry.S, add prototypes to asm/hypervisor.h
2) Don't build and update the cpulist using inline functions, this
was causing the cpu mask to not get updated in the caller.
3) Disable interrupts during the entire mondo send, otherwise our
cpu list and/or mondo block could get overwritten if we take
an interrupt and do a cpu mondo send on the current cpu.
4) Check for all possible error return types from the cpu_mondo_send()
hypervisor call. In particular:
HV_EOK) Our work is done, all cpus have received the mondo.
HV_CPUERROR) One or more of the cpus in the cpu list we passed
to the hypervisor are in error state. Use cpu_state()
calls over the entries in the cpu list to see which
ones. Record them in "error_mask" and report this
after we are done sending the mondo to cpus which are
not in error state.
HV_EWOULDBLOCK) We need to keep trying.
Any other error we consider fatal, we report the event and exit
immediately.
5) We only timeout if forward progress is not made. Forward progress
is defined as having at least one cpu get the mondo successfully
in a given cpu_mondo_send() call. Otherwise we bump a counter
and delay a little. If the counter hits a limit, we signal an
error and report the event.
Also, smp_call_function_mask() error handling reports the number
of cpus incorrectly.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 23 Feb 2006 22:19:28 +0000 (14:19 -0800)]
[SPARC64]: Fix TLB context allocation with SMT style shared TLBs.
The context allocation scheme we use depends upon there being a 1<-->1
mapping from cpu to physical TLB for correctness. Chips like Niagara
break this assumption.
So what we do is notify all cpus with a cross call when the context
version number changes, and if necessary this makes them allocate
a valid context for the address space they are running at the time.
Stress tested with make -j1024, make -j2048, and make -j4096 kernel
builds on a 32-strand, 8 core, T2000 with 16GB of ram.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 23 Feb 2006 00:20:11 +0000 (16:20 -0800)]
[SPARC64]: Fix %tstate ASI handling in start_thread{,32}()
Niagara helps us find a ancient bug in the sparc64 port :-)
The ASI_* values are plain constant defines, thus signed 32-bit
on sparc64. To put shift this into the regs->tstate value we were
doing or'ing "(ASI_PNF << 24)" into there.
ASI_PNF is 0x82 and shifted left by 24 makes that topmost bit the
sign bit in a 32-bit value. This would get sign extended to 64-bits
and thus corrupt the top-half of the reg->tstate value.
This never caused problems in pre-Niagara cpus because the only thing
up there were the condition code values. But Niagara has the global
register level field, and this all 1's value is illegal there so
Niagara gives an illegal instruction trap due to this bug.
I'm pretty sure this bug is about as old as the sparc64 port itself.
This also points out that we weren't setting ASI_PNF for 32-bit tasks.
We should, so fix that while we're here.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 23 Feb 2006 00:15:45 +0000 (16:15 -0800)]
[SPARC64]: Drop %gl to 0 before re-enabling PSTATE_IE in rtrap
If we take a window fault, on SUN4V set %gl to zero before we
turn PSTATE_IE back on in %pstate. Otherwise if we take an
interrupt we'll end up with corrupt register state.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 22 Feb 2006 06:31:11 +0000 (22:31 -0800)]
[SPARC64]: Create a seperate kernel TSB for 4MB/256MB mappings.
It can map all of the linear kernel mappings with zero TSB hash
conflicts for systems with 16GB or less ram. In such cases, on
SUN4V, once we load up this TSB the first time with all the
mappings, we never take a linear kernel mapping TLB miss ever
again, the hypervisor handles them all.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 22 Feb 2006 00:55:23 +0000 (16:55 -0800)]
[SPARC64]: Use sun4v_cpu_idle() in cpu_idle() on SUN4V.
We have to turn off the "polling nrflag" bit when we sleep
the cpu like this, so that we'll get a cross-cpu interrupt
to wake the processor up from the yield.
We also have to disable PSTATE_IE in %pstate around the yield
call and recheck need_resched() in order to avoid any races.
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6 / log