Jean Delvare [Wed, 22 Mar 2006 06:48:32 +0000 (03:48 -0300)]
V4L/DVB (3568b): saa7111: Prevent array overrun
Explicitely state the number of registers the SAA7111 has, and use that
defined value where relevant. This should prevent any future array overrun
like the one I just fixed in the saa7110 driver.
This patch also saves 8 bytes of memory as a side effect, as the register
cache was larger than needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Jean Delvare [Wed, 22 Mar 2006 06:48:33 +0000 (03:48 -0300)]
V4L/DVB (3568a): saa7114: Fix i2c block write
Fix the i2c block write mode of the saa7114 driver. A previous code change
accidentally commented out a local variable increment, which should have been
kept, causing the register writes over the I2C bus to never be batched,
replacing any attempted block write by slower, individual write transactions.
Also drop the commented out code, as it only adds to confusion.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove the assumption that driver_register() returns the number of devices
bound to the driver. In fact, it returns zero for success or a negative
error value.
All callers of macio_register_driver() either ignore the return value or
return it as the return value of a module_init() function.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove the assumption that driver_register() returns the number of devices
bound to the driver. In fact, it returns zero for success or a negative
error value.
Nobody uses the return value of of_register_driver() anyway.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Jean Delvare [Wed, 22 Mar 2006 07:20:26 +0000 (23:20 -0800)]
[PATCH] macintosh: cleanup the use of i2c headers
Cleanup the use of i2c headers in macintosh drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Linus Torvalds [Thu, 23 Mar 2006 01:39:38 +0000 (17:39 -0800)]
scsi: link in the debug driver last
If the debug driver is built-in, link it in last, so that any real
drivers will probe first, rather than having the debug driver pick the
first scsi slots..
Signed-off-by: Douglas Gilbert <dougg@torque.net> Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Acked-by: James Bottomley <James.Bottomley@SteelEye.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[TCP]: Do not use inet->id of global tcp_socket when sending RST.
[NETFILTER]: Fix undefined references to get_h225_addr
[NETFILTER]: futher {ip,ip6,arp}_tables unification
[NETFILTER]: Fix xt_policy address matching
[NETFILTER]: nf_conntrack: support for layer 3 protocol load on demand
[NETFILTER]: x_tables: set the protocol family in x_tables targets/matches
[NETFILTER]: conntrack: cleanup the conntrack ID initialization
[NETFILTER]: nfnetlink_queue: fix nfnetlink message size
[NETFILTER]: ctnetlink: Fix expectaction mask dumping
[NETFILTER]: Fix Kconfig typos
[NETFILTER]: Fix ip6tables breakage from {get,set}sockopt compat layer
* master.kernel.org:/home/rmk/linux-2.6-serial:
[SERIAL] Merge avlab serial board entries in parport_serial
[SERIAL] kernel console should send CRLF not LFCR
Eric Sesterhenn [Wed, 22 Mar 2006 21:49:48 +0000 (22:49 +0100)]
[PATCH] Use of uninitialized variable in drivers/net/depca.c
hi,
this fixes coverity bug #888, where the variable
dev is used uninitialized. I assume the programmer
meant to use mdev, which is initialized.
Compile tested only.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Artur Skawina [Tue, 21 Mar 2006 21:04:36 +0000 (22:04 +0100)]
[PATCH] sis900 adm7001 PHY support
this patch is required to get a SIS964 based motherboard ethernet working (FSC D1875)
(picking the #1 transceiver, instead of the last one, in case no known ones were found
might be a better default, and would have worked in this case too)
Signed-off-by: Artur Skawina <art_k@o2.pl> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Frank Pavlic [Wed, 22 Mar 2006 15:03:44 +0000 (16:03 +0100)]
[PATCH] s390: qeth :allow setting of attribute "route6" to "no_router".
[patch 4/6] s390: qeth :allow setting of attribute "route6" to "no_router".
From: Ursula Braun <braunu@de.ibm.com>
when setting route6 attribute back to no_router qeth does not
issue an IP ASSIST command to reset router value to no_router.
Once primary_router is set device stays in this mode.
Issue an IP ASSIST command when no_router is set in route6.
Device will be reset and thus will not longer run as a primary
router.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
diffstat:
qeth_main.c | 5 -----
1 files changed, 5 deletions(-) Signed-off-by: Jeff Garzik <jeff@garzik.org>
Frank Pavlic [Wed, 22 Mar 2006 15:03:41 +0000 (16:03 +0100)]
[PATCH] s390: qeth driver cleanups
[patch 3/6] s390: qeth driver cleanups
From: Ursula Braun <braunu@de.ibm.com>
- code analyzing tool BEAM has found some unreachable
and unnecessary statements and also conditions
which are always true.
- removed some useless MII code since OSA card will never
allow to set such values.
Sergei Shtylylov [Wed, 22 Mar 2006 06:53:52 +0000 (22:53 -0800)]
[PATCH] AMD Au1xx0: fix Ethernet TX stats
With Au1xx0 Ethernet driver, TX bytes/packets always remain zero. The
problem seems to be that when packet has been transmitted, the length word
in DMA buffer is zero.
The patch updates the TX stats when a buffer is fed to DMA. The initial
2.4 patch was posted to linux-mips@linux-mips.org by Thomas Lange 21 Jan
2005.
Signed-off-by: Thomas Lange <thomas@corelatus.se> Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Jordan Crouse <jordan.crouse@amd.com> Cc: Jeff Garzik <jgarzik@pobox.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox [Wed, 22 Mar 2006 15:52:40 +0000 (15:52 +0000)]
[PATCH] libata: Fix a drive detection problem
The current code follows the spec but uses an overlong delay. This would
be great if the hardware did. Several vendors however forget the D7
pulldown. Fortunately 0xFF isnt a sane reset state so we can use it to
skip detection as is done in drivers/ide. (ie this is a tested solution
over a long time)
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Right now I think the code is a nonsense. Most likely, I copied it from
old ip_build_xmit(), where it was really special, we had to decide
whether to generate unique ID when generating the first (well, the last)
fragment.
In ip_push_pending_frames() it does not make sense, it should use plain
ip_select_ident() instead.
Signed-off-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves {ip,ip6,arp}t_entry_{match,target} definitions to
x_tables.h. This move simplifies code and future compatibility fixes.
Signed-off-by: Dmitry Mishin <dim@openvz.org> Acked-off-by: Kirill Korotaev <dev@openvz.org> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
[NETFILTER]: nf_conntrack: support for layer 3 protocol load on demand
x_tables matches and targets that require nf_conntrack_ipv[4|6] to work
don't have enough information to load on demand these modules. This
patch introduces the following changes to solve this issue:
o nf_ct_l3proto_try_module_get: try to load the layer 3 connection
tracker module and increases the refcount.
o nf_ct_l3proto_module put: drop the refcount of the module.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
[NETFILTER]: x_tables: set the protocol family in x_tables targets/matches
Set the family field in xt_[matches|targets] registered.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
[NETFILTER]: conntrack: cleanup the conntrack ID initialization
Currently the first conntrack ID assigned is 2, use 1 instead.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Fix oversized message, use NLMSG_SPACE just one since it reserves space
for the netlink header and NFA_SPACE for every attribute.
Thanks to Harald Welte for the feedback
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
The expectation mask has some particularities that requires a different
handling. The protocol number fields can be set to non-valid protocols,
ie. l3num is set to 0xFFFF. Since that protocol does not exist, the mask
tuple will not be dumped. Moreover, this results in a kernel panic when
nf_conntrack accesses the array of protocol handlers, that is PF_MAX (0x1F)
long.
This patch introduces the function ctnetlink_exp_dump_mask, that correctly
dumps the expectation mask. Such function uses the l3num value from the
expectation tuple that is a valid layer 3 protocol number. The value of the
l3num mask isn't dumped since it is meaningless from the userspace side.
Thanks to Yasuyuki Kozakai and Patrick McHardy for the feedback.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Victor [Wed, 22 Mar 2006 20:14:14 +0000 (20:14 +0000)]
[ARM] 3386/1: AT91RM9200 Clock update
Patch from Andrew Victor
This patch includes a few changes to the clock support on the
AT91RM9200.
1. Added definitions for Ethernet, MMC, TWI, USARTs, and SPI peripheral
clocks.
2. Replaced some hard-coded hex values with the text definitions in
at91rm9200_sys.h.
3. If the USB96M bit is set for PLLB, then the rate of PLLB is not
affected but only the USB Host/Device clocks which are derived from it.
Issue reported by Sergei Sharonov.
Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Andrew Victor [Wed, 22 Mar 2006 20:14:13 +0000 (20:14 +0000)]
[ARM] 3384/1: AT91RM9200: Timer
Patch from Andrew Victor
If the timer interrupt is ever significantly delayed (or after the
system was suspended), the system could spin incrementing the time for
too long.
The fix is to replace the "do {} while" with a "while {}".
Orignal patch by Savin Zlobec and Peter Menzebach.
Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ARM] 3381/1: ixp2000: fix slowport write timing control register fields
Patch from Lennert Buytenhek
The original version of the chip docs had the PW and SU fields in
the slowport write timing control register accidentally reversed.
This is mentioned in the errata (documentation change #4) and fixed
in newer docs.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On the IXDP2x00s, the NPU that is PCI master is always the egress
(i.e. 'master') NPU. At least on the IXDP2800, both NPUs have flash,
so the ixp2000_has_flash() check in ixdp2x00_master_npu() is useless.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ARM] 3379/1: ixp2000: use generic 8250 debug macros
Patch from Lennert Buytenhek
The xscale UART in the ixp2000 is basically just an 8250 UART (with
some extra bits and pieces), so we can use the generic 8250 debug
macros on the ixp2000.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ixp2000 used to initially mark GPIO interrupts as invalid, and not
mark them valid until set_irq_type() was called, but this doesn't
work if you want to use request_irq() with the SA_TRIGGER_* flags.
So, just mark the GPIO interrupts valid from the beginning. We
configure GPIOs as inputs when set_irq_type() is called anyway, so
this shouldn't be a problem.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Add a secondary TSB for hugepage mappings.
[SPARC]: Respect vm_page_prot in io_remap_page_range().
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[TG3]: Bump driver version and reldate.
[TG3]: Skip phy power down on some devices
[TG3]: Fix SRAM access during tg3_init_one()
[X25]: dte facilities 32 64 ioctl conversion
[X25]: allow ITU-T DTE facilities for x25
[X25]: fix kernel error message 64 bit kernel
[X25]: ioctl conversion 32 bit user to 64 bit kernel
[NET]: socket timestamp 32 bit handler for 64 bit kernel
[NET]: allow 32 bit socket ioctl in 64 bit kernel
[BLUETOOTH]: Return negative error constant
James Morris [Wed, 22 Mar 2006 08:09:22 +0000 (00:09 -0800)]
[PATCH] SELinux: add slab cache for inode security struct
Add a slab cache for the SELinux inode security struct, one of which is
allocated for every inode instantiated by the system.
The memory savings are considerable.
On 64-bit, instead of the size-128 cache, we have a slab object of 96
bytes, saving 32 bytes per object. After booting, I see about 4000 of
these and then about 17,000 after a kernel compile. With this patch, we
save around 530KB of kernel memory in the latter case. On 32-bit, the
savings are about half of this.
Signed-off-by: James Morris <jmorris@namei.org> Acked-by: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
James Morris [Wed, 22 Mar 2006 08:09:20 +0000 (00:09 -0800)]
[PATCH] SELinux: fix hard link count for selinuxfs root directory
A further fix is needed for selinuxfs link count management, to ensure that
the count is correct for the parent directory when a subdirectory is
created. This is only required for the root directory currently, but the
code has been updated for the general case.
Signed-off-by: James Morris <jmorris@namei.org> Acked-by: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
James Morris [Wed, 22 Mar 2006 08:09:19 +0000 (00:09 -0800)]
[PATCH] selinuxfs cleanups: sel_make_avc_files
Fix copy & paste error in sel_make_avc_files(), removing a supurious call to
d_genocide() in the error path. All of this will be cleaned up by
kill_litter_super().
Signed-off-by: James Morris <jmorris@namei.org> Acked-by: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
James Morris [Wed, 22 Mar 2006 08:09:18 +0000 (00:09 -0800)]
[PATCH] selinuxfs cleanups: sel_make_bools
Remove the call to sel_make_bools() from sel_fill_super(), as policy needs to
be loaded before the boolean files can be created. Policy will never be
loaded during sel_fill_super() as selinuxfs is kernel mounted during init and
the only means to load policy is via selinuxfs.
Also, the call to d_genocide() on the error path of sel_make_bools() is
incorrect and replaced with sel_remove_bools().
Signed-off-by: James Morris <jmorris@namei.org> Acked-by: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Unify the error path of sel_fill_super() so that all errors pass through the
same point and generate an error message. Also, removes a spurious dput() in
the error path which breaks the refcounting for the filesystem
(litter_kill_super() will correctly clean things up itself on error).
Signed-off-by: James Morris <jmorris@namei.org> Acked-by: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Stephen Smalley [Wed, 22 Mar 2006 08:09:13 +0000 (00:09 -0800)]
[PATCH] selinux: Disable automatic labeling of new inodes when no policy is loaded
This patch disables the automatic labeling of new inodes on disk
when no policy is loaded.
Discussion is here:
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=180296
In short, we're changing the behavior so that when no policy is loaded,
SELinux does not label files at all. Currently it does add an 'unlabeled'
label in this case, which we've found causes problems later.
SELinux always maintains a safe internal label if there is none, so with this
patch, we just stick with that and wait until a policy is loaded before adding
a persistent label on disk.
The effect is simply that if you boot with SELinux enabled but no policy
loaded and create a file in that state, SELinux won't try to set a security
extended attribute on the new inode on the disk. This is the only sane
behavior for SELinux in that state, as it cannot determine the right label to
assign in the absence of a policy. That state usually doesn't occur, but the
rawhide installer seemed to be misbehaving temporarily so it happened to show
up on a test install.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov> Acked-by: James Morris <jmorris@namei.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paul Jackson [Wed, 22 Mar 2006 08:09:11 +0000 (00:09 -0800)]
[PATCH] mm: slab cache interleave rotor fix
The alien cache rotor in mm/slab.c assumes that the first online node is
node 0. Eventually for some archs, especially with hotplug, this will no
longer be true.
Fix the interleave rotor to handle the general case of node numbering.
Signed-off-by: Paul Jackson <pj@sgi.com> Acked-by: Christoph Lameter <clameter@engr.sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix bogus node loop in hugetlb.c alloc_fresh_huge_page(), which was
assuming that nodes are numbered contiguously from 0 to num_online_nodes().
Once the hotplug folks get this far, that will be false.
Signed-off-by: Paul Jackson <pj@sgi.com> Acked-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] slab: fix drain_array() so that it works correctly with the shared_array
The list_lock also protects the shared array and we call drain_array() with
the shared array. Therefore we cannot go as far as I wanted to but have to
take the lock in a way so that it also protects the array_cache in
drain_pages.
(Note: maybe we should make the array_cache locking more consistent? I.e.
always take the array cache lock for shared arrays and disable interrupts
for the per cpu arrays?)
Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] slab: make drain_array more universal by adding more parameters
And a parameter to drain_array to control the freeing of all objects and
then use drain_array() to replace instances of drain_array_locked with
drain_array. Doing so will avoid taking locks in those locations if the
arrays are empty.
Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] slab: cache_reap(): further reduction in interrupt holdoff
cache_reap takes the l3->list_lock (disabling interrupts) unconditionally
and then does a few checks and maybe does some cleanup. This patch makes
cache_reap() only take the lock if there is work to do and then the lock is
taken and released for each cleaning action.
The checking of when to do the next reaping is done without any locking and
becomes racy. Should not matter since reaping can also be skipped if the
slab mutex cannot be acquired.
The same is true for the touched processing. If we get this wrong once in
awhile then we will mistakenly clean or not clean the shared cache. This
will impact performance slightly.
Note that the additional drain_array() function introduced here will fall
out in a subsequent patch since array cleaning will now be very similar
from all callers.
Signed-off-by: Christoph Lameter <clameter@sgi.com> Cc: Pekka Enberg <penberg@cs.helsinki.fi> Cc: Manfred Spraul <manfred@colorfullife.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make shrink_all_memory() repeat the attempts to free more memory if there
seems to be no pages to free.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Chen, Kenneth W [Wed, 22 Mar 2006 08:09:03 +0000 (00:09 -0800)]
[PATCH] optimize follow_hugetlb_page
follow_hugetlb_page() walks a range of user virtual address and then fills
in list of struct page * into an array that is passed from the argument
list. It also gets a reference count via get_page(). For compound page,
get_page() actually traverse back to head page via page_private() macro and
then adds a reference count to the head page. Since we are doing a virt to
pte look up, kernel already has a struct page pointer into the head page.
So instead of traverse into the small unit page struct and then follow a
link back to the head page, optimize that with incrementing the reference
count directly on the head page.
The benefit is that we don't take a cache miss on accessing page struct for
the corresponding user address and more importantly, not to pollute the
cache with a "not very useful" round trip of pointer chasing. This adds a
moderate performance gain on an I/O intensive database transaction
workload.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com> Cc: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Quite a long time back, prepare_hugepage_range() replaced
is_aligned_hugepage_range() as the callback from mm/mmap.c to arch code to
verify if an address range is suitable for a hugepage mapping.
is_aligned_hugepage_range() stuck around, but only to implement
prepare_hugepage_range() on archs which didn't implement their own.
Most archs (everything except ia64 and powerpc) used the same
implementation of is_aligned_hugepage_range(). On powerpc, which
implements its own prepare_hugepage_range(), the custom version was never
used.
In addition, "is_aligned_hugepage_range()" was a bad name, because it
suggests it returns true iff the given range is a good hugepage range,
whereas in fact it returns 0-or-error (so the sense is reversed).
This patch cleans up by abolishing is_aligned_hugepage_range(). Instead
prepare_hugepage_range() is defined directly. Most archs use the default
version, which simply checks the given region is aligned to the size of a
hugepage. ia64 and powerpc define custom versions. The ia64 one simply
checks that the range is in the correct address space region in addition to
being suitably aligned. The powerpc version (just as previously) checks
for suitable addresses, and if necessary performs low-level MMU frobbing to
set up new areas for use by hugepages.
No libhugetlbfs testsuite regressions on ppc64 (POWER5 LPAR).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Gibson [Wed, 22 Mar 2006 08:08:59 +0000 (00:08 -0800)]
[PATCH] hugepage: Move hugetlb_free_pgd_range() prototype to hugetlb.h
The optional hugepage callback, hugetlb_free_pgd_range() is presently
implemented non-trivially only on ia64 (but I plan to add one for powerpc
shortly). It has its own prototype for the function in asm-ia64/pgtable.h.
However, since the function is called from generic code, it make sense for
its prototype to be in the generic hugetlb.h header file, as the protypes
other arch callbacks already are (prepare_hugepage_range(),
set_huge_pte_at(), etc.). This patch makes it so.
Signed-off-by: David Gibson <dwg@au1.ibm.com> Cc: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Gibson [Wed, 22 Mar 2006 08:08:58 +0000 (00:08 -0800)]
[PATCH] hugepage: Fix hugepage logic in free_pgtables() harder
Turns out the hugepage logic in free_pgtables() was doubly broken. The
loop coalescing multiple normal page VMAs into one call to free_pgd_range()
had an off by one error, which could mean it would coalesce one hugepage
VMA into the same bundle (checking 'vma' not 'next' in the loop). I
transferred this bug into the new is_vm_hugetlb_page() based version.
Here's the fix.
This one didn't bite on powerpc previously for the same reason the
is_hugepage_only_range() problem didn't: powerpc's hugetlb_free_pgd_range()
is identical to free_pgd_range(). It didn't bite on ia64 because the
hugepage region is distant enough from any other region that the separated
PMD_SIZE distance test would always prevent coalescing the two together.
No libhugetlbfs testsuite regressions (ppc64, POWER5).
Signed-off-by: David Gibson <dwg@au1.ibm.com> Cc: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Gibson [Wed, 22 Mar 2006 08:08:57 +0000 (00:08 -0800)]
[PATCH] hugepage: Fix hugepage logic in free_pgtables()
free_pgtables() has special logic to call hugetlb_free_pgd_range() instead
of the normal free_pgd_range() on hugepage VMAs. However, the test it uses
to do so is incorrect: it calls is_hugepage_only_range on a hugepage sized
range at the start of the vma. is_hugepage_only_range() will return true
if the given range has any intersection with a hugepage address region, and
in this case the given region need not be hugepage aligned. So, for
example, this test can return true if called on, say, a 4k VMA immediately
preceding a (nicely aligned) hugepage VMA.
At present we get away with this because the powerpc version of
hugetlb_free_pgd_range() is just a call to free_pgd_range(). On ia64 (the
only other arch with a non-trivial is_hugepage_only_range()) we get away
with it for a different reason; the hugepage area is not contiguous with
the rest of the user address space, and VMAs are not permitted in between,
so the test can't return a false positive there.
Nonetheless this should be fixed. We do that in the patch below by
replacing the is_hugepage_only_range() test with an explicit test of the
VMA using is_vm_hugetlb_page().
This in turn changes behaviour for platforms where is_hugepage_only_range()
returns false always (everything except powerpc and ia64). We address this
by ensuring that hugetlb_free_pgd_range() is defined to be identical to
free_pgd_range() (instead of a no-op) on everything except ia64. Even so,
it will prevent some otherwise possible coalescing of calls down to
free_pgd_range(). Since this only happens for hugepage VMAs, removing this
small optimization seems unlikely to cause any trouble.
This patch causes no regressions on the libhugetlbfs testsuite - ppc64
POWER5 (8-way), ppc64 G5 (2-way) and i386 Pentium M (UP).
Signed-off-by: David Gibson <dwg@au1.ibm.com> Cc: William Lee Irwin III <wli@holomorphy.com> Acked-by: Hugh Dickins <hugh@veritas.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Gibson [Wed, 22 Mar 2006 08:08:56 +0000 (00:08 -0800)]
[PATCH] hugepage: Make {alloc,free}_huge_page() local
Originally, mm/hugetlb.c just handled the hugepage physical allocation path
and its {alloc,free}_huge_page() functions were used from the arch specific
hugepage code. These days those functions are only used with mm/hugetlb.c
itself. Therefore, this patch makes them static and removes their
prototypes from hugetlb.h. This requires a small rearrangement of code in
mm/hugetlb.c to avoid a forward declaration.
This patch causes no regressions on the libhugetlbfs testsuite (ppc64,
POWER5).
Signed-off-by: David Gibson <dwg@au1.ibm.com> Cc: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Gibson [Wed, 22 Mar 2006 08:08:55 +0000 (00:08 -0800)]
[PATCH] hugepage: Strict page reservation for hugepage inodes
These days, hugepages are demand-allocated at first fault time. There's a
somewhat dubious (and racy) heuristic when making a new mmap() to check if
there are enough available hugepages to fully satisfy that mapping.
A particularly obvious case where the heuristic breaks down is where a
process maps its hugepages not as a single chunk, but as a bunch of
individually mmap()ed (or shmat()ed) blocks without touching and
instantiating the pages in between allocations. In this case the size of
each block is compared against the total number of available hugepages.
It's thus easy for the process to become overcommitted, because each block
mapping will succeed, although the total number of hugepages required by
all blocks exceeds the number available. In particular, this defeats such
a program which will detect a mapping failure and adjust its hugepage usage
downward accordingly.
The patch below addresses this problem, by strictly reserving a number of
physical hugepages for hugepage inodes which have been mapped, but not
instatiated. MAP_SHARED mappings are thus "safe" - they will fail on
mmap(), not later with an OOM SIGKILL. MAP_PRIVATE mappings can still
trigger an OOM. (Actually SHARED mappings can technically still OOM, but
only if the sysadmin explicitly reduces the hugepage pool between mapping
and instantiation)
This patch appears to address the problem at hand - it allows DB2 to start
correctly, for instance, which previously suffered the failure described
above.
This patch causes no regressions on the libhugetblfs testsuite, and makes a
test (designed to catch this problem) pass which previously failed (ppc64,
POWER5).
Signed-off-by: David Gibson <dwg@au1.ibm.com> Cc: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Gibson [Wed, 22 Mar 2006 08:08:53 +0000 (00:08 -0800)]
[PATCH] hugepage: serialize hugepage allocation and instantiation
Currently, no lock or mutex is held between allocating a hugepage and
inserting it into the pagetables / page cache. When we do go to insert the
page into pagetables or page cache, we recheck and may free the newly
allocated hugepage. However, since the number of hugepages in the system
is strictly limited, and it's usualy to want to use all of them, this can
still lead to spurious allocation failures.
For example, suppose two processes are both mapping (MAP_SHARED) the same
hugepage file, large enough to consume the entire available hugepage pool.
If they race instantiating the last page in the mapping, they will both
attempt to allocate the last available hugepage. One will fail, of course,
returning OOM from the fault and thus causing the process to be killed,
despite the fact that the entire mapping can, in fact, be instantiated.
The patch fixes this race by the simple method of adding a (sleeping) mutex
to serialize the hugepage fault path between allocation and insertion into
pagetables and/or page cache. It would be possible to avoid the
serialization by catching the allocation failures, waiting on some
condition, then rechecking to see if someone else has instantiated the page
for us. Given the likely frequency of hugepage instantiations, it seems
very doubtful it's worth the extra complexity.
This patch causes no regression on the libhugetlbfs testsuite, and one
test, which can trigger this race now passes where it previously failed.
Actually, the test still sometimes fails, though less often and only as a
shmat() failure, rather processes getting OOM killed by the VM. The dodgy
heuristic tests in fs/hugetlbfs/inode.c for whether there's enough hugepage
space aren't protected by the new mutex, and would be ugly to do so, so
there's still a race there. Another patch to replace those tests with
something saner for this reason as well as others coming...
Signed-off-by: David Gibson <dwg@au1.ibm.com> Cc: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Gibson [Wed, 22 Mar 2006 08:08:51 +0000 (00:08 -0800)]
[PATCH] hugepage: Small fixes to hugepage clear/copy path
Move the loops used in mm/hugetlb.c to clear and copy hugepages to their
own functions for clarity. As we do so, we add some checks of need_resched
- we are, after all copying megabytes of memory here. We also add
might_sleep() accordingly. We generally dropped locks around the clear and
copy, already but not everyone has PREEMPT enabled, so we should still be
checking explicitly.
For this to work, we need to remove the clear_huge_page() from
alloc_huge_page(), which is called with the page_table_lock held in the COW
path. We move the clear_huge_page() to just after the alloc_huge_page() in
the hugepage no-page path. In the COW path, the new page is about to be
copied over, so clearing it was just a waste of time anyway. So as a side
effect we also fix the fact that we held the page_table_lock for far too
long in this path by calling alloc_huge_page() under it.
It causes no regressions on the libhugetlbfs testsuite (ppc64, POWER5).
Signed-off-by: David Gibson <dwg@au1.ibm.com> Cc: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Zhang, Yanmin [Wed, 22 Mar 2006 08:08:50 +0000 (00:08 -0800)]
[PATCH] Enable mprotect on huge pages
2.6.16-rc3 uses hugetlb on-demand paging, but it doesn_t support hugetlb
mprotect.
From: David Gibson <david@gibson.dropbear.id.au>
Remove a test from the mprotect() path which checks that the mprotect()ed
range on a hugepage VMA is hugepage aligned (yes, really, the sense of
is_aligned_hugepage_range() is the opposite of what you'd guess :-/).
In fact, we don't need this test. If the given addresses match the
beginning/end of a hugepage VMA they must already be suitably aligned. If
they don't, then mprotect_fixup() will attempt to split the VMA. The very
first test in split_vma() will check for a badly aligned address on a
hugepage VMA and return -EINVAL if necessary.
On i386 and x86-64, pte flag _PAGE_PSE collides with _PAGE_PROTNONE. The
identify of hugetlb pte is lost when changing page protection via mprotect.
A page fault occurs later will trigger a bug check in huge_pte_alloc().
The fix is to always make new pte a hugetlb pte and also to clean up
legacy code where _PAGE_PRESENT is forced on in the pre-faulting day.
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com> Cc: David Gibson <david@gibson.dropbear.id.au> Cc: "David S. Miller" <davem@davemloft.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Ken Chen <kenneth.w.chen@intel.com> Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com> Cc: Andi Kleen <ak@muc.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current current get_init_ra_size is not optimal across different IO
sizes and max_readahead values. Here is a quick summary of sizes computed
under current design and under the attached patch. All of these assume 1st
IO at offset 0, or 1st detected sequential IO.
32k max, 4k request
old new
-----------------
8k 8k
16k 16k
32k 32k
128k max, 4k request
old new
-----------------
32k 16k
64k 32k
128k 64k
128k 128k
128k max, 32k request
old new
-----------------
32k 64k <-----
64k 128k
128k 128k
512k max, 4k request
old new
-----------------
4k 32k <----
16k 64k
64k 128k
128k 256k
512k 512k
Cc: Oleg Nesterov <oleg@tv-sign.ru> Cc: Steven Pratt <slpratt@austin.ibm.com> Cc: Ram Pai <linuxram@us.ibm.com> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Oleg Nesterov [Wed, 22 Mar 2006 08:08:47 +0000 (00:08 -0800)]
[PATCH] readahead: ->prev_page can overrun the ahead window
If get_next_ra_size() does not grow fast enough, ->prev_page can overrun
the ahead window. This means the caller will read the pages from
->ahead_start + ->ahead_size to ->prev_page synchronously.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru> Cc: Steven Pratt <slpratt@austin.ibm.com> Cc: Ram Pai <linuxram@us.ibm.com> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hugh Dickins [Wed, 22 Mar 2006 08:08:46 +0000 (00:08 -0800)]
[PATCH] shmem: inline to avoid warning
shmem.c was named and shamed in Jesper's "Building 100 kernels" warnings:
shmem_parse_mpol is only used when CONFIG_TMPFS parses mount options; and
only called from that one site, so mark it inline like its non-NUMA stub.
[PATCH] vmscan: emove obsolete checks from shrink_list() and fix unlikely in refill_inactive_zone()
As suggested by Marcelo:
1. The optimization introduced recently for not calling
page_referenced() during zone reclaim makes two additional checks in
shrink_list unnecessary.
2. The if (unlikely(sc->may_swap)) in refill_inactive_zone is optimized
for the zone_reclaim case. However, most peoples system only does swap.
Undo that.
Signed-off-by: Christoph Lameter <clameter@sgi.com> Cc: Marcelo Tosatti <marcelo.tosatti@cyclades.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Nick Piggin [Wed, 22 Mar 2006 08:08:40 +0000 (00:08 -0800)]
[PATCH] remove set_page_count() outside mm/
set_page_count usage outside mm/ is limited to setting the refcount to 1.
Remove set_page_count from outside mm/, and replace those users with
init_page_count() and set_page_refcounted().
This allows more debug checking, and tighter control on how code is allowed
to play around with page->_count.
Signed-off-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A couple of places set_page_count(page, 1) that don't need to.
Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Paul Mackerras <paulus@samba.org> Cc: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
projects / linux-2.6 / log