ide: push pc callback pointer into the ide_drive_t structure
Refrain from carrying the callback ptr with every packet command since the
callback function is only one anyways. ide_drive_t is probably not the most
suitable place for it right now but is the more sane solution. Besides, these
structs are going to be reorganized anyways during the generic ide rewrite.
Add ide_host_add() helper which does ide_host_alloc()+ide_host_register(),
then convert ide_setup_pci_device[s](), ide_legacy_device_add() and some
host drivers to use it.
While at it:
* Fix ide_setup_pci_device[s](), ide_arm.c, gayle.c, ide-4drives.c,
macide.c, q40ide.c, cmd640.c and cs5520.c to return correct error value.
* -ENOENT -> -ENOMEM in rapide.c, ide-h8300.c, ide-generic.c, au1xxx-ide.c
and pmac.c
* -ENODEV -> -ENOMEM in palm_bk3710.c, ide_platform.c and delkin_cb.c
* Reserve memory resources for all IDE ports at once by moving
request_mem_region() out of 'for ()' loop and always defining
GAYLE_IDEREG_SIZE to 0x2000.
* Keep memory resources even if no free IDE slots can be found
(this driver is unloadable currently).
ide: filter out "default" transfer mode values in set_xfer_rate()
* Filter out "default" transfer mode values (0x00 - default PIO mode,
0x01 - default PIO mode w/ IORDY disabled) in write handler for obsoleted
/proc/ide/hd?/settings:current_speed setting.
Allowing "default" transfer mode values is a dangerous thing to do as
we don't support programming controller to the "default" transfer mode
and devices often use different values for the default and maximum PIO
mode (i.e. PIO2 default and PIO4 maximum) so the controller will stay
programmed for higher PIO mode while device will use the lower PIO mode.
There is no functionality loss as by using special IOCTLs device can
still be programmed to "default" transfer modes (it is only useful for
debugging/testing purposes anyway).
* Remove no longer needed IDE_HFLAG_ABUSE_SET_DMA_MODE host flag, it was
previously used by few host drivers to program the controller to PIO0
timings for "default" transfer mode == 0x01 (although some host drivers
would program invalid PIO timings instead).
* Cleanup ide_set_xfer_rate() and add BUG_ON().
Suggested-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Alan Cox has noticed some time ago that hpt34x is broken
(http://lkml.org/lkml/2007/7/3/257):
"No the old driver doesn't even do that. It starts up. It spuriously
adjusts some non writable PCI BAR registers, prints a message about
resources being in use already then exits."
Reported-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide: pass hw_regs_t-s to ide_device_add[_all]() (take 3)
* Add 'hw_regs_t **hws' argument to ide_device_add[_all]() and convert
host drivers + ide_legacy_init_one() + ide_setup_pci_device[s]() to use
it instead of calling ide_init_port_hw() directly.
[ However if host has > 1 port we must still set hwif->chipset to hint
consecutive ide_find_port() call that the previous slot is occupied. ]
* Unexport ide_init_port_hw().
v2:
* Use defines instead of hard-coded values in buddha.c, gayle.c and q40ide.c.
(Suggested by Geert Uytterhoeven)
* Better patch description.
v3:
* Fix build problem in ide-cs.c. (Noticed by Stephen Rothwell)
There should be no functional changes caused by this patch.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (82 commits)
ipw2200: Call netif_*_queue() interfaces properly.
netxen: Needs to include linux/vmalloc.h
[netdrvr] atl1d: fix !CONFIG_PM build
r6040: rework init_one error handling
r6040: bump release number to 0.18
r6040: handle RX fifo full and no descriptor interrupts
r6040: change the default waiting time
r6040: use definitions for magic values in descriptor status
r6040: completely rework the RX path
r6040: call napi_disable when puting down the interface and set lp->dev accordingly.
mv643xx_eth: fix NETPOLL build
r6040: rework the RX buffers allocation routine
r6040: fix scheduling while atomic in r6040_tx_timeout
r6040: fix null pointer access and tx timeouts
r6040: prefix all functions with r6040
rndis_host: support WM6 devices as modems
at91_ether: use netstats in net_device structure
sfc: Create one RX queue and interrupt per CPU package by default
sfc: Use a separate workqueue for resets
sfc: I2C adapter initialisation fixes
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc32: pass -m32 when building vmlinux.lds
sparc: Fixes the DRM layer build on sparc.
ide: merge <asm-sparc/ide_64.h> with <asm-sparc/ide_32.h>
ide: <asm-sparc/ide_64.h>: use __raw_{read,write}w()
ide: <asm-sparc/ide_32.h>: use __raw_{read,write}w()
ide: <asm-sparc/ide_64.h>: use %r0 for outw_be()
sparc64: Do not define BIO_VMERGE_BOUNDARY.
netif_carrier_{on,off}() handles starting and stopping packet
flow into the driver. So there is no reason to invoke netif_stop_queue()
and netif_wake_queue() in response to link status events.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reworks the error handling in r6040_init_one
in order not to leak resources and correcly unmap and release
PCI regions of the MAC. Also prefix printk's with the driver name
for clarity.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch bumps the release of the r6040 driver. There has been
quite some versions of it out there, but this one is the one
people should report bugs against.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
r6040: handle RX fifo full and no descriptor interrupts
This patch allows the MAC to handle the RX FIFO full
and no descriptor available interrupts. While we are at it
replace the TX interrupt with its corresponding definition.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch changes the default waiting time of a packet, which
along with our previous r6040_rx path, was causing huge delays
with another host (160 to 230 ms).
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch completely reworks the RX path in order to be
more accurate about what is going on with the MAC.
We no longer read the error from the MLSR register instead read
the descriptor status register which reflects, the error per descriptor.
We now allocate skbs on the fly in r6040_rx, and we handle allocation
failure instead of simply dropping the packet. Remove the
rx_free_desc counter of r6040_private structure since we
allocate skbs in the RX path.
r6040_rx_buf_alloc is now removed and becomes unuseless.
Signed-Off-By: Joerg Albert <jal2@gmx.de> Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Joseph Fannin <jfannin@gmail.com> and Takashi Iwai <tiwai@suse.de>
noticed that commit 073a345c04b01da0cc5b79ac7be0c7c8b1691ef5
("mv643xx_eth: clarify irq masking and unmasking") broke the
mv643xx_eth build when NETPOLL is enabled, due to it not renaming
one instance of INT_CAUSE_EXT in mv643xx_eth_netpoll(). This patch
takes care of that instance as well.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Cc: Dale Farnsworth <dale@farnsworth.org> Cc: Joseph Fannin <jfannin@gmail.com> Cc: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Rework the RX buffers allocation function so that we do not
leak memory in the case we could not allocate skbs for the
RX path. Propagate the errors to the r6040_up function
where we call the RX buffers allocation function.
Also rename the r6040_alloc_txbufs function to
r6040_init_txbufs, to reflect what it really does.
Signed-Off-By: Joerg Albert <jal2@gmx.de> Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
r6040: fix scheduling while atomic in r6040_tx_timeout
Add a helper function which only modifies R6040 MAC registers
use it when we timeout, and on adapter initialization. Fix
the scheduling while atomic but in the timeout routine due
to the reallocation of rx/tx buffers.
Signed-Off-By: Joerg Albert <jal2@gmx.de> Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Paulius Zaleckas [Thu, 17 Jul 2008 08:01:26 +0000 (11:01 +0300)]
at91_ether: use netstats in net_device structure
Use net_device_stats from net_device structure instead of local.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt> Tested-by: Marc Pignat <marc.pignat@hevs.ch> Acked-by: Andrew Victor <linux@maxim.org.za> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ben Hutchings [Fri, 18 Jul 2008 18:03:10 +0000 (19:03 +0100)]
sfc: Create one RX queue and interrupt per CPU package by default
Using multiple cores in the same package to handle received traffic
does not appear to provide a performance benefit. Therefore use CPU
topology information to count CPU packages and use that as the default
number of RX queues and interrupts. We rely on interrupt balancing to
spread the interrupts across packages.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ben Hutchings [Fri, 18 Jul 2008 17:59:12 +0000 (18:59 +0100)]
sfc: I2C adapter initialisation fixes
As recommended by Jean Delvare:
- Increase timeout to 50 ms
- Leave adapter class clear so that unwanted drivers do not probe our bus
- Use strlcpy() for name initialisation
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch makes e1000 driver ioport-free.
This corrects behavior in probe function so as not to request ioport
resources as long as they are not really needed. This is based on the
ioport-free patch of e1000 driver from Auke Kok and Tomohiro Kusumi.
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@jp.fujitsu.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: Jeff Kirsher<jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ixgbe driver was untested with device ID 8086:10c8 but still advertises
support. Currently if this device is present in the system when the driver
is loaded, the system will panic.
Remove this device ID until full support can be tested with available
hardware. This patch is necessary for 2.6.24, 2.6.25 and 2.6.26
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Anton Vorontsov [Tue, 22 Jul 2008 22:41:24 +0000 (15:41 -0700)]
netdev: bunch of drivers: avoid WARN at net/core/dev.c:1328
The drivers were touching net queue before it has been started, so
without this patch, the drivers will potentially WARN at
net/core/dev.c:1328.
I don't have the hardware for the drivers below, so this patch is
untested, and thus should be carefully peer reviewed.
tc35815.c
au1000_eth.c
bfin_mac.c
macb.c
^ The four drivers are using phylib, they're calling netif_start_queue()
in open() callback. So trivially remove netif_tx_schedule_all().
Phylib will handle netif_carrier_*().
cpmac.c
fec_mpc52xx.c
fs_enet/fs_enet-main.c
sh_eth.c
^ The same as above, but these were also needlessly calling
netif_carrier_*() functions. So removed queue calls and also remove
carrier calls, since phylib will handle it. fs_enet-main.c also didn't
call netif_start_queue() at open(), this is fixed now.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Jones [Tue, 15 Jul 2008 23:54:53 +0000 (19:54 -0400)]
8139too: Make PIO/MMIO a runtime decision through a module parameter.
This is needed to support devices that only work with PIO without
penalising devices that work fine with MMIO in distro kernels.
It also allows us to eventually use PIO as a fallback when setting
up MMIO fails.
Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Wang Jian [Wed, 16 Jul 2008 13:46:17 +0000 (21:46 +0800)]
net/phy: Fix copper/fiber auto-selection for 88e1111
The 27.15 bit (MII_M1111_HWCFG_FIBER_COPPER_AUTO) is disable bit. When
set to 1, copper/fiber auto selection is disabled. The current code
to enable but actually disable auto selection.
Signed-off-by: Wang Jian <lark@linux.net.cn> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
NX3031 supports cut-through operation where ingress packets are
directly dma'ed into host buffers to reduce latency.
This requires larger dma buffers (2kb) and different alignemnt.
The buffer posting logic is changed a bit. The free rx buffers
are maintained in linked list, since the received reference
handles can be out of order. However rx descriptors are still
posted sequentially, indexed by producer.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
MAC addr, multicast filters, mtu are set through firmware commands
in firmware v4.0.0+ because of virtualization of physical ports.
Link status is also read from registers allocated by firmware for
each virtual port.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
New revision of netxen chip has 2MB PCI memory. Older chips
had 128MB addressable PCI memory. To retain compatibility,
this patch adds function pointers based on pci bar0 size.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
projects / linux-2.6 / log