John Linn [Wed, 2 Jul 2008 22:11:28 +0000 (15:11 -0700)]
powerpc/virtex: Fix booting of Xilinx FPGAs with 16550 for 405 and 440
The following changes add processing to initialize the Xilinx 16550 UART
in the boot wrapper for Virtex targets without firmware. Normally the
boot wrapper assumes that the serial port has already been initialized by
firmware.
The wrapper was also modified to add the 440 build.
Signed-off-by: John Linn <john.linn@xilinx.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Michael Neuling [Tue, 1 Jul 2008 04:01:39 +0000 (14:01 +1000)]
powerpc: Update for VSX core file and ptrace
This correctly hooks the VSX dump into Roland McGrath core file
infrastructure. It adds the VSX dump information as an additional elf
note in the core file (after talking more to the tool chain/gdb guys).
This also ensures the formats are consistent between signals, ptrace
and core files.
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Neuling [Tue, 1 Jul 2008 04:01:39 +0000 (14:01 +1000)]
powerpc: Fix compile error for CONFIG_VSX
Fix compile error when CONFIG_VSX is enabled.
arch/powerpc/kernel/signal_64.c: In function 'restore_sigcontext':
arch/powerpc/kernel/signal_64.c:241: error: 'i' undeclared (first use in this function)
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Eric B Munson [Mon, 30 Jun 2008 16:12:13 +0000 (02:12 +1000)]
powerpc: Keep 3 high personality bytes across exec
Currently when a 32 bit process is exec'd on a powerpc 64 bit host the
value in the top three bytes of the personality is clobbered. patch
adds a check in the SET_PERSONALITY macro that will carry all the
values in the top three bytes across the exec.
These three bytes currently carry flags to disable address randomisation,
limit the address space, force zeroing of an mmapped page, etc. Should an
application set any of these bits they will be maintained and honoured on
homogeneous environment but discarded and ignored on a heterogeneous
environment. So if an application requires all mmapped pages to be initialised
to zero and a wrapper is used to setup the personality and exec the target,
these flags will remain set on an all 32 or all 64 bit envrionment, but they
will be lost in the exec on a mixed 32/64 bit environment. Losing these bits
means that the same application would behave differently in different
environments. Tested on a POWER5+ machine with 64bit kernel and a mixed
64/32 bit user space.
Signed-off-by: Eric B Munson <ebmunson@us.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Bart Van Assche [Sat, 28 Jun 2008 06:51:35 +0000 (16:51 +1000)]
powerpc: Make sure that include/asm-powerpc/spinlock.h does not trigger compilation warnings
When compiling kernel modules for ppc that include <linux/spinlock.h>,
gcc prints a warning message every time it encounters a function
declaration where the inline keyword appears after the return type.
This makes sure that the order of the inline keyword and the return
type is as gcc expects it. Additionally, the __inline__ keyword is
replaced by inline, as checkpatch expects.
Signed-off-by: Bart Van Assche <bart.vanassche@gmail.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Andy Whitcroft [Thu, 26 Jun 2008 09:55:58 +0000 (19:55 +1000)]
powerpc: Add 64 bit version of huge_ptep_set_wrprotect
The implementation of huge_ptep_set_wrprotect() directly calls
ptep_set_wrprotect() to mark a hugepte write protected. However this
call is not appropriate on ppc64 kernels as this is a small page only
implementation. This can lead to the hash not being flushed correctly
when a mapping is being converted to COW, allowing processes to continue
using the original copy.
Currently huge_ptep_set_wrprotect() unconditionally calls
ptep_set_wrprotect(). This is fine on ppc32 kernels as this call is
generic. On 64 bit this is implemented as:
pte_update(mm, addr, ptep, _PAGE_RW, 0);
On ppc64 this last parameter is the page size and is passed directly on
to hpte_need_flush():
hpte_need_flush(mm, addr, ptep, old, huge);
And this directly affects the page size we pass to flush_hash_page():
flush_hash_page(vaddr, rpte, psize, ssize, 0);
As this changes the way the hash is calculated we will flush the wrong
pages, potentially leaving live hashes to the original page.
Move the definition of huge_ptep_set_wrprotect() to the 32/64 bit specific
headers.
Signed-off-by: Andy Whitcroft <apw@shadowen.org> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Andrew Lewis [Thu, 26 Jun 2008 09:29:05 +0000 (19:29 +1000)]
powerpc: Prevent memory corruption due to cache invalidation of unaligned DMA buffer
On PowerPC processors with non-coherent cache architectures the DMA
subsystem calls invalidate_dcache_range() before performing a DMA read
operation. If the address and length of the DMA buffer are not aligned
to a cache-line boundary this can result in memory outside of the DMA
buffer being invalidated in the cache. If this memory has an
uncommitted store then the data will be lost and a subsequent read of
that address will result in an old value being returned from main memory.
Only when the DMA buffer starts on a cache-line boundary and is an exact
mutiple of the cache-line size can invalidate_dcache_range() be called,
otherwise flush_dcache_range() must be called. flush_dcache_range()
will first flush uncommitted writes, and then invalidate the cache.
Signed-off-by: Andrew Lewis <andrew-lewis at netspace.net.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Neuling [Wed, 25 Jun 2008 04:07:18 +0000 (14:07 +1000)]
powerpc: Add VSX context save/restore, ptrace and signal support
This patch extends the floating point save and restore code to use the
VSX load/stores when VSX is available. This will make FP context
save/restore marginally slower on FP only code, when VSX is available,
as it has to load/store 128bits rather than just 64bits.
Mixing FP, VMX and VSX code will get constant architected state.
The signals interface is extended to enable access to VSR 0-31
doubleword 1 after discussions with tool chain maintainers. Backward
compatibility is maintained.
The ptrace interface is also extended to allow access to VSR 0-31 full
registers.
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Neuling [Wed, 25 Jun 2008 04:07:18 +0000 (14:07 +1000)]
powerpc: Add VSX CPU feature
Add a VSX CPU feature. Also add code to detect if VSX is available
from the device tree.
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Joel Schopp <jschopp@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
VSX has 64 128bit registers. The first 32 regs overlap with the FP
registers and hence extend them with and additional 64 bits. The
second 32 regs overlap with the VMX registers.
This commit introduces the thread_struct changes required to reflect
this register layout. Ptrace and signals code is updated so that the
floating point registers are correctly accessed from the thread_struct
when CONFIG_VSX is enabled.
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Neuling [Thu, 26 Jun 2008 07:07:48 +0000 (17:07 +1000)]
powerpc: Add macros to access floating point registers in thread_struct.
We are going to change where the floating point registers are stored
in the thread_struct, so in preparation add some macros to access the
floating point registers. Update all code to use these new macros.
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Neuling [Wed, 25 Jun 2008 04:07:17 +0000 (14:07 +1000)]
powerpc: Fix MSR setting in 32 bit signal code
If we set the SPE MSR bit in save_user_regs we can blow away the VEC
bit. This doesn't matter in reality as they are in fact the same bit
but looks bad.
Also, when we add VSX in a later patch, we need to be able to set two
separate MSR bits here.
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Tony Breeds [Tue, 24 Jun 2008 04:20:29 +0000 (14:20 +1000)]
powerpc: Change the default link address for pSeries zImage kernels
Currently we set the start of the .text section to be 4Mb for pSeries.
In situations where the zImage is > 8Mb we'll fail to boot (due to
overlapping with OF). Move .text in a zImage from 4MB to 64MB
(well past OF).
We still will not be able to load large zImage unless we also move OF,
to that end, add a note to the zImage ELF to move OF to 32Mb. If this
is the very first kernel booted then we'll need to move OF manually by
setting real-base.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Tue, 24 Jun 2008 01:33:05 +0000 (11:33 +1000)]
powerpc: Use an alternative feature section in entry_64.S
Use an alternative feature section in _switch. There are three cases
handled here, either we don't have an SLB, in which case we jump over the
entire code section, or if we do we either do or don't have 1TB segments.
Boot tested on Power3, Power5 and Power5+.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Tue, 24 Jun 2008 01:33:03 +0000 (11:33 +1000)]
powerpc: Add self-tests of the feature fixup code
This commit adds tests of the feature fixup code, they are run during
boot if CONFIG_FTR_FIXUP_SELFTEST=y. Some of the tests manually invoke
the patching routines to check their behaviour, and others use the
macros and so are patched during the normal patching done during boot.
Because we have two sets of macros with different names, we use a macro
to generate the test of the macros, very niiiice.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Tue, 24 Jun 2008 01:33:02 +0000 (11:33 +1000)]
powerpc: Add logic to patch alternative feature sections
This commit adds the logic to patch alternative sections. This is fairly
straightforward, except for branches. Relative branches that jump from
inside the else section to outside of it need to be translated as they're
moved, otherwise they will jump to the wrong location.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Tue, 24 Jun 2008 01:32:54 +0000 (11:32 +1000)]
powerpc: Introduce infrastructure for feature sections with alternatives
The current feature section logic only supports nop'ing out code, this means
if you want to choose at runtime between instruction sequences, one or both
cases will have to execute the nop'ed out contents of the other section, eg:
BEGIN_FTR_SECTION
or 1,1,1
END_FTR_SECTION_IFSET(FOO)
BEGIN_FTR_SECTION
or 2,2,2
END_FTR_SECTION_IFCLR(FOO)
and the resulting code will be either,
or 1,1,1
nop
or,
nop
or 2,2,2
For small code segments this is fine, but for larger code blocks and in
performance criticial code segments, it would be nice to avoid the nops.
This commit starts to implement logic to allow the following:
BEGIN_FTR_SECTION
or 1,1,1
FTR_SECTION_ELSE
or 2,2,2
ALT_FTR_SECTION_END_IFSET(FOO)
and the resulting code will be:
or 1,1,1
or,
or 2,2,2
We achieve this by extending the existing FTR macros. The current feature
section semantic just becomes a special case, ie. if the else case is empty
we nop out the default case.
The key limitation is that the size of the else case must be less than or
equal to the size of the default case. If the else case is smaller the
remainder of the section is nop'ed.
We let the linker put the else case code in with the rest of the text,
so that relative branches from the else case are more likley to link,
this has the disadvantage that we can't free the unused else cases.
This commit introduces the required macro and linker script changes, but
does not enable the patching of the alternative sections.
We also need to update two hand-made section entries in reg.h and timex.h
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Tue, 24 Jun 2008 01:32:48 +0000 (11:32 +1000)]
powerpc: Consolidate feature fixup macros for 64/32 bit
Currently we have three versions of MAKE_FTR_SECTION_ENTRY(), the macro that
generates a feature section entry. There is 64bit version, a 32bit version
and version for 32bit code built with a 64bit kernel.
Rather than triplicating (?) the MAKE_FTR_SECTION_ENTRY() logic, we can
move the 64bit/32bit differences into separate macros, and then only have
one version of MAKE_FTR_SECTION_ENTRY().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Tue, 24 Jun 2008 01:32:39 +0000 (11:32 +1000)]
powerpc: Consolidate CPU and firmware feature fixup macros
The CPU and firmware feature fixup macros are currently spread across
three files, firmware.h, cputable.h and asm-compat.h. Consolidate them
into their own file, feature-fixups.h
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Tue, 24 Jun 2008 01:32:36 +0000 (11:32 +1000)]
powerpc: Split out do_feature_fixups() from cputable.c
The logic to patch CPU feature sections lives in cputable.c, but these days
it's used for CPU features as well as firmware features. Move it into
it's own file for neatness and as preparation for some additions.
While we're moving the code, we pull the loop body logic into a separate
routine, and remove a comment which doesn't apply anymore.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Tue, 24 Jun 2008 01:32:35 +0000 (11:32 +1000)]
powerpc: Add PPC_NOP_INSTR, a hash define for the preferred nop instruction
A bunch of code has hard-coded the value for a "nop" instruction, it
would be nice to have a #define for it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Tue, 24 Jun 2008 01:32:32 +0000 (11:32 +1000)]
powerpc: Add tests of the code patching routines
Add tests of the existing code patching routines, as well as the new
routines added in the last commit. The self-tests are run late in boot
when CONFIG_CODE_PATCHING_SELFTEST=y, which depends on DEBUG_KERNEL=y.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Tue, 24 Jun 2008 01:32:28 +0000 (11:32 +1000)]
powerpc: Add ppc_function_entry() which gets the entry point for a function
Because function pointers point to different things on 32-bit vs 64-bit,
add a macro that deals with dereferencing the OPD on 64-bit. The soon to
be merged ftrace wants this, as well as other code I am working on.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Tue, 24 Jun 2008 01:32:24 +0000 (11:32 +1000)]
powerpc: Make create_branch() return errors if the branch target is too large
If you pass a target value to create_branch() which is more than 32MB - 4,
or - 32MB away from the branch site, then it's impossible to create an
immediate branch. The current code doesn't check, which will lead to us
creating a branch to somewhere else - which is bad.
For code that cares to check we return 0, which is easy to check for, and
for code that doesn't at least we'll be creating an illegal instruction,
rather than a branch to some random address.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Tue, 24 Jun 2008 01:32:22 +0000 (11:32 +1000)]
powerpc: Allow create_branch() to return errors
Currently create_branch() creates a branch instruction for you, and
patches it into the call site. In some circumstances it would be nice
to be able to create the instruction and patch it later, and also some
code might want to check for errors in the branch creation before
doing the patching. A future commit will change create_branch() to
check for errors.
For callers that don't care, replace create_branch() with
patch_branch(), which just creates the branch and patches it directly.
While we're touching all the callers, change to using unsigned int *,
as this seems to match usage better. That allows (and requires) us to
remove the volatile in the definition of vector in powermac/smp.c and
mpc86xx_smp.c, that's correct because now that we're passing vector as
an unsigned int * the compiler knows that it's value might change
across the patch_branch() call.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Acked-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Jon Loeliger <jdl@freescale.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Tue, 24 Jun 2008 01:32:21 +0000 (11:32 +1000)]
powerpc: Move code patching code into arch/powerpc/lib/code-patching.c
We currently have a few routines for patching code in asm/system.h, because
they didn't fit anywhere else. I'd like to clean them up a little and add
some more, so first move them into a dedicated C file - they don't need to
be inlined.
While we're moving the code, drop create_function_call(), it's intended
caller never got merged and will be replaced in future with something
different.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Julia Lawall [Mon, 23 Jun 2008 18:14:52 +0000 (04:14 +1000)]
drivers/macintosh/smu.c: Improve error handling
This makes two changes:
* As noted by Akinobu Mita in patch b1fceac2b9e04d278316b2faddf276015fc06e3b, alloc_bootmem never returns NULL
and always returns a zeroed region of memory. Thus the error checking code
and memset after the call to alloc_bootmem are not necessary.
* The old error handling code consisted of setting a global variable to
NULL and returning an error code, which could cause previously allocated
resources never to be freed. The patch adds calls to appropriate resource
deallocation functions.
Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Paul Mackerras <paulus@samba.org>
Adrian Bunk [Mon, 23 Jun 2008 17:46:57 +0000 (03:46 +1000)]
drivers/macintosh: Various cleanups
This contains the following cleanups:
- make the following needlessly global code static:
- adb.c: adb_controller
- adb.c: adb_init()
- adbhid.c: adb_to_linux_keycodes[] (also make it const)
- via-pmu68k.c: backlight_level
- via-pmu68k.c: backlight_enabled
- remove the following unused code:
- via-pmu68k.c: sleep_notifier_list
Signed-off-by: Adrian Bunk <bunk@kernel.org> Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Dave Kleikamp [Wed, 18 Jun 2008 22:32:56 +0000 (08:32 +1000)]
powerpc: hash_huge_page() should get the WIMG bits from the lpte
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com> Cc: Jon Tollefson <kniht@linux.vnet.ibm.com> Cc: Adam Litke <agl@us.ibm.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Paul Mackerras [Wed, 18 Jun 2008 05:29:12 +0000 (15:29 +1000)]
powerpc: Only demote individual slices rather than whole process
At present, if we have a kernel with a 64kB page size, and some
process maps something that has to be mapped with 4kB pages (such as a
cache-inhibited mapping on POWER5+, or the eHCA infiniband queue-pair
pages), we change the process to use 4kB pages everywhere. This hurts
the performance of HPC programs that access eHCA from userspace.
With this patch, the kernel will only demote the slice(s) containing
the eHCA or cache-inhibited mappings, leaving the remaining slices
able to use 64kB hardware pages.
This also changes the slice_get_unmapped_area code so that it is
willing to place a 64k-page mapping into (or across) a 4k-page slice
if there is no better alternative, i.e. if the program specified
MAP_FIXED or if there is not sufficient space available in slices that
are either empty or already have 64k-page mappings in them.
Signed-off-by: Paul Mackerras <paulus@samba.org> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Wed, 18 Jun 2008 00:47:26 +0000 (10:47 +1000)]
powerpc: Add cputable entry for POWER7
Add a cputable entry for the POWER7 processor.
Also tell firmware that we know about POWER7.
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Joel Schopp <jschopp@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Becky Bruce [Fri, 13 Jun 2008 23:41:43 +0000 (09:41 +1000)]
powerpc: Get rid of bitfields in ppc_bat struct
While working on the 36-bit physical support, I noticed that there
was exactly one line of code that actually referenced the bitfields.
So I got rid of them and redefined ppc_bat as a struct of 2 u32's:
batu and batl. I also got rid of the previous union that held the
bitfield structs and a word representation of the batu/l values.
This seems like a nicer solution than adding in a bunch of
new bitfields to support extended bat addressing that would never
get used, and just leaving the struct as-is would have been
incomplete in the face of large physical addressing.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Becky Bruce [Fri, 13 Jun 2008 23:41:42 +0000 (09:41 +1000)]
powerpc: Change BAT code to use phys_addr_t
Currently, the physical address is an unsigned long, but it should
be phys_addr_t in set_bat, [v/p]_mapped_by_bat. Also, create a
macro that can convert a large physical address into the correct
format for programming the BAT registers.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Arnd Bergmann [Thu, 12 Jun 2008 09:14:34 +0000 (19:14 +1000)]
powerpc: Provide dummy crash_shutdown_register
When kexec is disabled, the crash_shutdown_{un,}register
functions are not available in the kernel.
This provides dummy inline functions for those so that
the callers don't have to worry about it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Paul Mackerras <paulus@samba.org>
This frees a PTE bit when using 64K pages on ppc64. This is done
by getting rid of the separate _PAGE_HASHPTE bit. Instead, we just test
if any of the 16 sub-page bits is set. For non-combo pages (ie. real
64K pages), we set SUB0 and the location encoding in that field.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Daniel Walker [Mon, 9 Jun 2008 23:26:09 +0000 (09:26 +1000)]
macintosh/media bay: Convert semaphore to mutex
Signed-off-by: Daniel Walker <dwalker@mvista.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Daniel Walker [Mon, 9 Jun 2008 23:26:08 +0000 (09:26 +1000)]
macintosh/therm_windtunnel: Convert semaphore to mutex
Signed-off-by: Daniel Walker <dwalker@mvista.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Nick Piggin [Mon, 9 Jun 2008 23:26:08 +0000 (09:26 +1000)]
spufs: Convert nopfn to fault
Signed-off-by: Nick Piggin <npiggin@suse.de> Acked-by: Jeremy Kerr <jk@ozlabs.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Stephen Rothwell [Fri, 23 May 2008 06:28:54 +0000 (16:28 +1000)]
drivers/net: Use linux/of_{device,platform}.h instead of asm
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Stephen Rothwell [Fri, 23 May 2008 06:27:02 +0000 (16:27 +1000)]
macintosh: Use linux/of_{device,platform}.h instead of asm
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Nick Piggin [Wed, 21 May 2008 14:12:31 +0000 (00:12 +1000)]
powerpc: Optimise smp_wmb on 64-bit processors
For 64-bit processors, lwsync is the recommended method of store/store
ordering on caching enabled memory. For those subarchs which have
lwsync, use it rather than eieio for smp_wmb.
Signed-off-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (42 commits)
V4L/DVB (8108): Fix open/close race in saa7134
V4L/DVB (8100): V4L/vivi: fix possible memory leak in vivi_fillbuff
V4L/DVB (8097): xc5000: check device hardware state to determine if firmware download is needed
V4L/DVB (8096): au8522: prevent false-positive lock status
V4L/DVB (8092): videodev: simplify and fix standard enumeration
V4L/DVB (8075): stv0299: Uncorrected block count and bit error rate fixed
V4L/DVB (8074): av7110: OSD transfers should not be interrupted
V4L/DVB (8073): av7110: Catch another type of ARM crash
V4L/DVB (8071): tda10023: Fix possible kernel oops during initialisation
V4L/DVB (8069): cx18: Fix S-Video and Compsite inputs for the Yuan MPC718 and enable card entry
V4L/DVB (8068): cx18: Add I2C slave reset via GPIO upon initialization
V4L/DVB (8067): cx18: Fix firmware load for case when digital capture happens first
V4L/DVB (8066): cx18: Fix audio mux input definitions for HVR-1600 Line In 2 and FM radio
V4L/DVB (8063): cx18: Fix unintended auto configurations in cx18-av-core
V4L/DVB (8061): cx18: only select tuner / frontend modules if !DVB_FE_CUSTOMISE
V4L/DVB (8048): saa7134: Fix entries for Avermedia A16d and Avermedia E506
V4L/DVB (8044): au8522: tuning optimizations
V4L/DVB (8043): au0828: add support for additional USB device id's
V4L/DVB (8042): DVB-USB UMT-010 channel scan oops
V4L/DVB (8040): soc-camera: remove soc_camera_host_class class
...
Linus Torvalds [Sun, 29 Jun 2008 19:22:30 +0000 (12:22 -0700)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
dock: bay: Don't call acpi_walk_namespace() when ACPI is disabled.
ACPI: don't walk tables if ACPI was disabled
thermal: Create CONFIG_THERMAL_HWMON=n
Removed vmlinux* rule because it matches too many useful files, replacing
it with rules matching filetype by filename (e.g. *.gz). Also unignored
.mailmap from the top directory. Added a comment telling the user how to
check for tracked files being ignored.
Signed-off-by: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 29 Jun 2008 19:15:10 +0000 (12:15 -0700)]
Merge branch 'audit.b52' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current
* 'audit.b52' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
[PATCH] remove useless argument type in audit_filter_user()
[PATCH] audit: fix kernel-doc parameter notation
[PATCH] kernel/audit.c: nlh->nlmsg_type is gotten more than once
Richard Sharpe [Wed, 25 Jun 2008 02:11:13 +0000 (19:11 -0700)]
firewire: fw-sbp2: fix parsing of logical unit directories
There is a small off-by-one bug in firewire-sbp2. This causes problems
when a device exports multiple LUN Directories. I found it when trying
to talk to a SONY DVD Jukebox.
Signed-off-by: Richard Sharpe <realrichardsharpe@gmail.com> Acked-by: Kristian Høgsberg <krh@redhat.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (op. order, changelog)
Arjan van de Ven [Sun, 22 Jun 2008 20:03:02 +0000 (17:03 -0300)]
V4L/DVB (8108): Fix open/close race in saa7134
The saa7134 driver uses a (non-atomic) variable in an attempt to
only allow one opener of the device (how it deals with sending
the fd over unix sockets I don't know).
Unfortunately, the release function first decrements this variable,
and THEN goes on to disable more of the device. This allows for
a race where another opener of the device comes in after the decrement of
the variable, configures the hardware just to then see the hardware
be disabled by the rest of the release function.
This patch makes the release function use the same lock as the open
function to protect the hardware as well as the variable (which now
at least has some locking to protect it).
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Steven Toth [Sun, 22 Jun 2008 00:06:02 +0000 (21:06 -0300)]
V4L/DVB (8097): xc5000: check device hardware state to determine if firmware download is needed
This patch ensures that the xc5000 will have firmware loaded as needed if the
part is powered down or reset via gpio from the host. An example of this, in
some cases, could be after the system resumes from standby or hibernate modes.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Sat, 21 Jun 2008 16:23:27 +0000 (13:23 -0300)]
V4L/DVB (8092): videodev: simplify and fix standard enumeration
VIDIOC_ENUMSTD did not return all the PAL/SECAM/NTSC variants: it just returned
one single PAL/SECAM/NTSC standard without separate entries for the trickier
standards like NTSC-JP.
Changed the code so that it behaves better.
Also simplified the if/switch statements into a common standards lookup table.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Andy Walls [Sun, 22 Jun 2008 05:00:09 +0000 (02:00 -0300)]
V4L/DVB (8069): cx18: Fix S-Video and Compsite inputs for the Yuan MPC718 and enable card entry
cx18: Fix S-Video and Compsite input settings for the Yuan MPC718 per user
reports from Yuri Warczynski <Yuri.Warczynski@gmail.com> and
Brian Hope <brian@hopefamily.info> and enable the card entry. The tuner reset
GPIO pin is likely incorrect as the tuner firmware cannot be reloaded without a
reboot. It is likely the audio routing is done via GPIO which is not
implemented yet, as users report audio doesn't work for some inputs.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Andy Walls [Sun, 22 Jun 2008 04:27:00 +0000 (01:27 -0300)]
V4L/DVB (8068): cx18: Add I2C slave reset via GPIO upon initialization
cx18: Add I2C slave reset via GPIO upon initialization. One user,
Michael <msd4824@yahoo.com>, has reported this allows his HVR-1600 EEPROM to
be consistently recognized when using (long,) 100 msec delays. The delays in
this commit are nominal (10 & 40 msec) and need testing/tuning on boards with
I2C problems to find the right values.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Andy Walls [Sun, 22 Jun 2008 03:04:21 +0000 (00:04 -0300)]
V4L/DVB (8067): cx18: Fix firmware load for case when digital capture happens first
This is a fix for the case when a digital capture from dvr0 happens first after
modprobe, before access to any cx18 v4l2 device nodes. The initial dvb feed
start has been changed to load the firmware if not already loaded. Also fixed a
use counter to correct dvb feed accounting if starting the transport DMA fails.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Andy Walls [Fri, 20 Jun 2008 02:17:05 +0000 (23:17 -0300)]
V4L/DVB (8066): cx18: Fix audio mux input definitions for HVR-1600 Line In 2 and FM radio
Fix the cx18-cards.c structures for the HVR-1600 to reflect that audio Line In 2
and FM radio audio go to AIN3 and AIN4 of the CS5345 mux respectively. Verified
by physical inspection of an HVR-1600MCE, by listening to FM broadcasts with the
HVR-1600MCE, and by comparing with the card definition for a PVR-150 in ivtv.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Andy Walls [Sat, 14 Jun 2008 06:58:08 +0000 (03:58 -0300)]
V4L/DVB (8063): cx18: Fix unintended auto configurations in cx18-av-core
Change the cx18-av-core code so that accesses to cx23418 av core that
cause auto-configuration will be adjusted to emulate the auto-configuration
behavior of the cx25843. This fixes the VBI displayed as video at the top of
the frame for NTSC and probably other things.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (8040): soc-camera: remove soc_camera_host_class class
Devices can either be class devices or bus devices, not both at the
same time. Soc-camera host devices usually have a platform device as
their parent. Trying to also register them with a class crashes the
kernel, when linked statically. Interestingly, it works when built
as a module. Thanks to Paulius Zaleckas for reporting.
projects / linux-2.6 / log