drm/radeon: fix texture uploads with large 3d textures (bug 13980)
Texture uploads could hit the blitter coordinate limit, adjust the texture
offset when uploading the pieces. Make sure to check the end address of the
upload too.
Vegard Nossum [Thu, 12 Jun 2008 06:55:59 +0000 (08:55 +0200)]
x86, lockdep: fix "WARNING: at kernel/lockdep.c:2658 check_flags+0x4c/0x128()"
Alessandro Suardi reported:
> Recently upgraded my FC6 desktop to Fedora 9; with the
> latest nautilus RPM updates my VNC session went nuts
> with nautilus pegging the CPU for everything that breathed.
>
> I now reverted to an earlier nautilus package, but during
> the peak CPU period my kernel spat this:
>
> [314185.623294] ------------[ cut here ]------------
> [314185.623414] WARNING: at kernel/lockdep.c:2658 check_flags+0x4c/0x128()
> [314185.623514] Modules linked in: iptable_filter ip_tables x_tables
> sunrpc ipv6 fuse snd_via82xx snd_ac97_codec ac97_bus snd_mpu401_uart
> snd_rawmidi via686a hwmon parport_pc sg parport uhci_hcd ehci_hcd
> [314185.623924] Pid: 12314, comm: nautilus Not tainted 2.6.26-rc5-git2 #4
> [314185.624021] [<c0115b95>] warn_on_slowpath+0x41/0x7b
> [314185.624021] [<c010de70>] ? do_page_fault+0x2c1/0x5fd
> [314185.624021] [<c0128396>] ? up_read+0x16/0x28
> [314185.624021] [<c010de70>] ? do_page_fault+0x2c1/0x5fd
> [314185.624021] [<c012fa33>] ? __lock_acquire+0xbb4/0xbc3
> [314185.624021] [<c012d0a0>] check_flags+0x4c/0x128
> [314185.624021] [<c012fa73>] lock_acquire+0x31/0x7d
> [314185.624021] [<c0128cf6>] __atomic_notifier_call_chain+0x30/0x80
> [314185.624021] [<c0128cc6>] ? __atomic_notifier_call_chain+0x0/0x80
> [314185.624021] [<c0128d52>] atomic_notifier_call_chain+0xc/0xe
> [314185.624021] [<c0128d81>] notify_die+0x2d/0x2f
> [314185.624021] [<c01043b0>] do_int3+0x1f/0x4d
> [314185.624021] [<c02f2d3b>] int3+0x27/0x2c
> [314185.624021] =======================
> [314185.624021] ---[ end trace 1923f65a2d7bb246 ]---
> [314185.624021] possible reason: unannotated irqs-off.
> [314185.624021] irq event stamp: 488879
> [314185.624021] hardirqs last enabled at (488879): [<c0102d67>]
> restore_nocheck+0x12/0x15
> [314185.624021] hardirqs last disabled at (488878): [<c0102dca>]
> work_resched+0x19/0x30
> [314185.624021] softirqs last enabled at (488876): [<c011a1ba>]
> __do_softirq+0xa6/0xac
> [314185.624021] softirqs last disabled at (488865): [<c010476e>]
> do_softirq+0x57/0xa6
>
> I didn't seem to find it with some googling, so here it is.
>
> I was incidentally ltracing that process to try and find out
> what was gulping down that much CPU (sorry, no idea
> whether ltrace and the WARNING happened at the same
> time or which came first) and:
Yeah, this is extremely likely to be the source of the warning.
The warning should be harmless, however.
> Box is my trusty noname K7-800, 512MB RAM; if there's
> anything else useful I might be able to provide, just ask.
It would be interesting to see where the int3 comes from. Too bad,
lockdep doesn't provide the register dump. The stacktrace also doesn't
go further than the int3(), I wonder if this int3 came from userspace?
The ltrace readme says "software breakpoints, like gdb", so I guess
this is the case. Yep, seems like it.
This looks relevant:
| commit fb1dac909d94ff807cd833d340c6827c3a957159
| Author: Peter Zijlstra <a.p.zijlstra@chello.nl>
| Date: Wed Jan 16 09:51:59 2008 +0100
|
| lockdep: more hardirq annotations for notify_die()
I'm attaching a similarly-looking patch for this case (DO_VM86_ERROR),
though I suspect it might be missing for the other cases
(DO_ERROR/DO_ERROR_INFO) as well.
David Howells [Sat, 7 Jun 2008 16:18:40 +0000 (17:18 +0100)]
x86: fix an incompatible pointer type warning on 64-bit compilations
Fix an incompatible pointer type warning on x86_64 compilations.
early_memtest() is passing a u64* to find_e820_area_size() which is expecting
an unsigned long. Change t_start and t_size to unsigned long as those are
also 64-bit types on x88_64.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
| there is a problem in 2.6.26-rc3 which was not there in case of
| 2.6.25: the CPU wakes up ~90,000 times per sec instead of ~60 per sec.
|
| I also "git bisected" the problem, the result is:
|
| 6e908947b4995bc0e551a8257c586d5c3e428201 is first bad commit
| commit 6e908947b4995bc0e551a8257c586d5c3e428201
| Author: Ingo Molnar <mingo@elte.hu>
| Date: Fri Mar 21 14:32:36 2008 +0100
|
| x86: fix ioapic bug again
the original problem is fixed by Maciej W. Rozycki in the tip/x86/apic
branch (confirmed by Márton), but those changes are too intrusive for
v2.6.26 so we'll go for the less intrusive (repeated) revert now.
Reported-and-bisected-by: Németh Márton <nm127@freemail.hu> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Joe Korty [Mon, 2 Jun 2008 21:21:06 +0000 (17:21 -0400)]
x86: fix asm warning in head_32.S
On Mon, May 19, 2008 at 04:10:02PM -0700, Linus Torvalds wrote:
> It also causes these warnings on 32-bit PAE:
>
> AS arch/x86/kernel/head_32.o
> arch/x86/kernel/head_32.S: Assembler messages:
> arch/x86/kernel/head_32.S:225: Warning: left operand is a bignum; integer 0 assumed
> arch/x86/kernel/head_32.S:609: Warning: left operand is a bignum; integer 0 assumed
>
> and I do not see why (the end result seems to be identical).
Fix head_32.S gcc bignum warnings when CONFIG_PAE=y.
arch/x86/kernel/head_32.S: Assembler messages:
arch/x86/kernel/head_32.S:225: Warning: left operand is a bignum; integer 0 assumed
arch/x86/kernel/head_32.S:609: Warning: left operand is a bignum; integer 0 assumed
The assembler was stumbling over the 64-bit constant 0x100000000 in the
KPMDS #define.
Testing: a cmp(1) on head_32.o before and after shows the binary is unchanged.
Signed-off-by: Joe Korty <joe.korty@ccur.com Cc: Hugh Dickins <hugh@veritas.com> Cc: Theodore Tso <tytso@mit.edu> Cc: Gabriel C <nix.or.die@googlemail.com> Cc: Keith Packard <keithp@keithp.com> Cc: "Pallipadi Venkatesh" <venkatesh.pallipadi@intel.com> Cc: Eric Anholt <eric@anholt.net> Cc: "Siddha Suresh B" <suresh.b.siddha@intel.com> Cc: bugme-daemon@bugzilla.kernel.org Cc: airlied@linux.ie Cc: "Barnes Jesse" <jesse.barnes@intel.com> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Cc: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Henry Nestler [Mon, 12 May 2008 13:44:39 +0000 (15:44 +0200)]
x86: fix endless page faults in mount_block_root for Linux 2.6
Page faults in kernel address space between PAGE_OFFSET up to
VMALLOC_START should not try to map as vmalloc.
Fix rarely endless page faults inside mount_block_root for root
filesystem at boot time.
All 32bit kernels up to 2.6.25 can fail into this hole.
I can not present this under native linux kernel. I see, that the 64bit
has fixed the problem. I copied the same lines into 32bit part.
Recorded debugs are from coLinux kernel 2.6.22.18 (virtualisation):
http://www.henrynestler.com/colinux/testing/pfn-check-0.7.3/20080410-antinx/bug16-recursive-page-fault-endless.txt
The physicaly memory was trimmed down to 192MB to better catch the bug.
More memory gets the bug more rarely.
Details, how every x86 32bit system can fail:
Start from "mount_block_root",
http://lxr.linux.no/linux/init/do_mounts.c#L297
There the variable "fs_names" got one memory page with 4096 bytes.
Variable "p" walks through the existing file system types. The first
string is no problem.
But, with the second loop in mount_block_root the offset of "p" is not
at beginning of page, the offset is for example +9, if "reiserfs" is the
first in list.
Than calls do_mount_root, and lands in sys_mount.
Remember: Variable "type_page" contains now "fs_type+9" and not contains
a full page.
The sys_mount copies 4096 bytes with function "exact_copy_from_user()":
http://lxr.linux.no/linux/fs/namespace.c#L1540
Mostly exist pages after the buffer "fs_names+4096+9" and the page fault
handler was not called. No problem.
In the case, if the page after "fs_names+4096" is not mapped, the page
fault handler was called from http://lxr.linux.no/linux/fs/namespace.c#L1320
The do_page_fault gots an address 0xc03b4000.
It's kernel address, address >= TASK_SIZE, but not from vmalloc! It's
from "__getname()" alias "kmem_cache_alloc".
The "error_code" is 0. "vmalloc_fault" will be call:
http://lxr.linux.no/linux/arch/i386/mm/fault.c#L332
"vmalloc_fault" tryed to find the physical page for a non existing
virtual memory area. The macro "pte_present" in vmalloc_fault()
got a next page fault for 0xc0000ed0 at:
http://lxr.linux.no/linux/arch/i386/mm/fault.c#L282
No PTE exist for such virtual address. The page fault handler was trying
to sync the physical page for the PTE lockup.
This called vmalloc_fault() again for address 0xc000000, and that also
was not existing. The endless began...
In normal case the cpu would still loop with disabled interrrupts. Under
coLinux this was catched by a stack overflow inside printk debugs.
Signed-off-by: Henry Nestler <henry.nestler@gmail.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
block: disable IRQs until data is written to relay channel
As we may run relay_reserve from interrupt context we must always disable
IRQs. This is because a call to relay_reserve may expose previously written
data to use space.
Updated new message code and an old but related comment.
Signed-off-by: Carl Henrik Lunde <chlunde@ping.uio.no> Signed-off-by: Jens Axboe <jens.axboe@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
virt_to_head_page cannot return NULL. virt_to_page also
does not return NULL. pfn_valid() needs to be used to
figure out if a page is valid. Otherwise the page struct
reference that was returned may have PageReserved() set
to indicate that it is not a valid page.
As discussed further in the thread, virt_addr_valid() is the preferable
way to validate the object pointer in this case. In addition to fixing
up the reserved page case, it also has the benefit of encapsulating the
hack introduced by commit 4016a1390d07f15b267eecb20e76a48fd5c524ef on
the impacted platforms, allowing us to get rid of the extra checking in
kobjsize() for the platforms that don't perform this type of bizarre
memory_end abuse (every nommu platform that isn't blackfin). If blackfin
decides to get in line with every other platform and use PageReserved
for the DMA pages in question, kobjsize() will also continue to work
fine.
It also turns out that compound_order() will give us back 0-order for
non-head pages, so we can get rid of the PageCompound check and just
use compound_order() directly. Clean that up while we're at it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org> Reviewed-by: Christoph Lameter <clameter@sgi.com> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 12 Jun 2008 14:47:44 +0000 (07:47 -0700)]
Merge branch 'core/iter-div' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core/iter-div' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
always_inline timespec_add_ns
add an inlined version of iter_div_u64_rem
common implementation of iterative div/mod
Sam Ravnborg [Thu, 12 Jun 2008 13:02:55 +0000 (15:02 +0200)]
kbuild: ignore powerpc specific symbols in modpost
Kumar Gala <galak@kernel.crashing.org> wrote:
We have a case in powerpc in which we want to link some library
routines with all module objects. The routines are intended for
handling out-of-line function call register save/restore so having
them as EXPORT_SYMBOL() is counter productive (we do also need to
link the same "library" code into the kernel).
Without this patch a powerpc build would error out and fail
to build modules with the added register save/restore module.
There were two obvious solutions:
1) To link the .o file before the modpost stage
2) To ignore the symbols in modpost
Option 1) was ruled out because we do not have any separate
linking stage for single file modules.
This patch implements option 2 - and do so only for powerpc.
The symbols we ignore are all undefined symbols named:
_restgpr_*, _savegpr_*, _rest32gpr_*, _save32gpr_*
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org>
Lai Jiangshan [Thu, 12 Jun 2008 08:43:07 +0000 (16:43 +0800)]
sched: 64-bit: fix arithmetics overflow
(overflow means weight >= 2^32 here, because inv_weigh = 2^32/weight)
A weight of a cfs_rq is the sum of weights of which entities
are queued on this cfs_rq, so it will overflow when there are
too many entities.
Although, overflow occurs very rarely, but it break fairness when
it occurs. 64-bits systems have more memory than 32-bit systems
and 64-bit systems can create more process usually, so overflow may
occur more frequently.
This patch guarantees fairness when overflow happens on 64-bit systems.
Thanks to the optimization of compiler, it changes nothing on 32-bit.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Ingo Molnar <mingo@elte.hu>
timespec_add_ns is used from the x86-64 vdso, which cannot call out to
other kernel code. Make sure that timespec_add_ns is always inlined
(and only uses always_inlined functions) to make sure there are no
unexpected calls.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
iter_div_u64_rem is used in the x86-64 vdso, which cannot call other
kernel code. For this case, provide the always_inlined version,
__iter_div_u64_rem.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
We have a few instances of the open-coded iterative div/mod loop, used
when we don't expcet the dividend to be much bigger than the divisor.
Unfortunately modern gcc's have the tendency to strength "reduce" this
into a full mod operation, which isn't necessarily any faster, and
even if it were, doesn't exist if gcc implements it in libgcc.
The workaround is to put a dummy asm statement in the loop to prevent
gcc from performing the transformation.
This patch creates a single implementation of this loop, and uses it
to replace the open-coded versions I know about.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: john stultz <johnstul@us.ibm.com> Cc: Segher Boessenkool <segher@kernel.crashing.org> Cc: Christian Kujau <lists@nerdbynature.de> Cc: Robert Hancock <hancockr@shaw.ca> Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: don't use reset-resume if drivers don't support it
USB: isp1760: Assign resource fields before adding hcd
isight_firmware: Avoid crash on loading invalid firmware
USB: fix build bug in USB_ISIGHTFW
Linus Torvalds [Tue, 10 Jun 2008 18:59:43 +0000 (14:59 -0400)]
USB: don't use reset-resume if drivers don't support it
This patch tries to identify which devices are able to accept
reset-resume handling, by checking that there is at least one
interface driver bound and that all of the drivers have a reset_resume
method defined. If these conditions don't hold then during resume
processing, the device is logicall disconnected.
This is only a temporary fix. Later on we will explicitly unbind
drivers that can't handle reset-resumes.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Cc: Oliver Neukum <oliver@neukum.org> Cc: Pavel Machek <pavel@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Matthew Garrett [Fri, 6 Jun 2008 19:35:15 +0000 (12:35 -0700)]
isight_firmware: Avoid crash on loading invalid firmware
Different tools generate slightly different formats of the isight
firmware. Ensure that the firmware buffer is not overrun, while still
ensuring that the correct amount of data is written if trailing data is
present.
Signed-off-by: Matthew Garrett <mjg@redhat.com> Report-by: Justin Mattock <justinmattock@gmail.com> Tested-by: Justin Mattock <justinmattock@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ingo Molnar [Mon, 2 Jun 2008 19:21:03 +0000 (21:21 +0200)]
USB: fix build bug in USB_ISIGHTFW
USB: fix build bug in USB_ISIGHTFW
-tip tree testing found this build bug:
drivers/built-in.o: In function `isight_firmware_load':
isight_firmware.c:(.text+0x1ade08): undefined reference to `request_firmware'
isight_firmware.c:(.text+0x1adf9c): undefined reference to `release_firmware'
Arjan van de Ven [Mon, 19 May 2008 22:55:15 +0000 (15:55 -0700)]
ACPI: Reject below-freezing temperatures as invalid critical temperatures
My laptop thinks that it's a good idea to give -73C as the critical
CPU temperature.... which isn't the best thing since it causes a shutdown
right at bootup.
Temperatures below freezing are clearly invalid critical thresholds
so just reject these as such.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Acked-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Tue, 10 Jun 2008 06:29:26 +0000 (14:29 +0800)]
ACPICA: Fix for access to deleted object <regression>
Fixes problem introduced in 20080123, with fix for Unload operator.
Parse tree object can be already deleted; must use the opcode
within the WalkState.
ACPI: kmemcheck: Caught 16-bit read from freed memory
http://bugzilla.kernel.org/show_bug.cgi?id=10669
Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Tue, 10 Jun 2008 06:26:57 +0000 (14:26 +0800)]
ACPICA: Fix to make _SST method optional
Fixes a problem introduced in 20080514 where the status of
execution of _SST is incorrectly returned to the caller. _SST
is optional, and if it is AE_NOT_FOUND, the exception should be
ignored.
Bob Moore [Tue, 10 Jun 2008 06:14:17 +0000 (14:14 +0800)]
ACPICA: Fix for Load operator, load table at the namespace root
This reverts a change introduced in version 20071019. The table
is now loaded at the namespace root even though this goes against
the ACPI specification. This provides compatibility with other
ACPI implementations.
Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Bob Moore [Tue, 10 Jun 2008 06:12:50 +0000 (14:12 +0800)]
ACPICA: Ignore ACPI table signature for Load() operator
Only "SSDT" is acceptable to the ACPI spec, but tables are
seen with OEMx and null sigs. Therefore, signature validation
is worthless. Apparently MS ACPI accepts such signatures, ACPICA
must be compatible.
http://bugzilla.kernel.org/show_bug.cgi?id=10454
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Akinobu Mita [Mon, 9 Jun 2008 23:22:26 +0000 (16:22 -0700)]
ACPI: use memory_read_from_buffer()
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Acked-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com>
Holger Macht [Mon, 9 Jun 2008 23:22:24 +0000 (16:22 -0700)]
bay: exit if notify handler cannot be installed
If acpi_install_notify_handler() for a bay device fails, the bay driver is
superfluous. Most likely, another driver (like libata) is already caring
about this device anyway. Furthermore,
register_hotplug_dock_device(acpi_handle) from the dock driver must not be
called twice with the same handler. This would result in an endless loop
consuming 100% of CPU. So clean up and exit.
Signed-off-by: Holger Macht <hmacht@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com>
Tim Pepper [Mon, 9 Jun 2008 23:22:25 +0000 (16:22 -0700)]
dock.c remove trailing printk whitespace
Signed-off-by: Tim Pepper <lnxninja@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com>
Adrian Bunk [Mon, 9 Jun 2008 23:22:24 +0000 (16:22 -0700)]
proper prototype for acpi_processor_tstate_has_changed()
This patch adds a proper prototype for acpi_processor_tstate_has_changed()
in include/acpi/processor.h
Signed-off-by: Adrian Bunk <bunk@kernel.org> Cc: Len Brown <lenb@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com>
Fenghua Yu [Mon, 9 Jun 2008 23:48:18 +0000 (16:48 -0700)]
ACPI: handle invalid ACPI SLIT table
This is a SLIT sanity checking patch. It moves slit_valid() function to
generic ACPI code and does sanity checking for both x86 and ia64. It sets up
node_distance with LOCAL_DISTANCE and REMOTE_DISTANCE when hitting invalid
SLIT table on ia64. It also cleans up unused variable localities in
acpi_parse_slit() on x86.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com>
Bjorn Helgaas [Mon, 9 Jun 2008 23:52:06 +0000 (16:52 -0700)]
PNPACPI: use _CRS IRQ descriptor length for _SRS
When configuring the resources of an ACPI device, we first evaluate _CRS
to get a template of resource descriptors, then fill in the specific
resource values we want, and finally evaluate _SRS to actually configure
the device.
Some resources have optional fields, so the size of encoded descriptors
varies depending on the specific values. For example, IRQ descriptors can
be either two or three bytes long. The third byte contains triggering
information and can be omitted if the IRQ is edge-triggered and active
high.
The BIOS often assumes that IRQ descriptors in the _SRS buffer use the
same format as those in the _CRS buffer, so this patch enforces that
constraint.
The "Start Dependent Function" descriptor also has an optional byte, but
we don't currently encode those descriptors, so I didn't do anything for
those.
I have tested this patch on a Toshiba Portege 4000. Without the patch,
parport_pc claims the parallel port only if I use "pnpacpi=off". This
patch makes it work with PNPACPI.
This is an extension of a patch by Tom Jaeger:
http://bugzilla.kernel.org/show_bug.cgi?id=9487#c42
References:
http://bugzilla.kernel.org/show_bug.cgi?id=5832 Enabling ACPI Plug and Play in kernels >2.6.9 kills Parallel support
http://bugzilla.kernel.org/show_bug.cgi?id=9487 buggy firmware expects four-byte IRQ resource descriptor (was: Serial port disappears after Suspend on Toshiba R25)
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=1d5b285da1893b90507b081664ac27f1a8a3dc5b related ACPICA fix
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com>
Bjorn Helgaas [Mon, 9 Jun 2008 23:52:05 +0000 (16:52 -0700)]
pnpacpi: fix shareable IRQ encode/decode
When we encode IRQ resources, we should use the "shareable" flag we got
from _PRS rather than guessing based on the IRQ trigger mode.
This is based on a patch by Tom Jaeger:
http://bugzilla.kernel.org/show_bug.cgi?id=9487#c32
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com>
Bjorn Helgaas [Mon, 9 Jun 2008 23:52:04 +0000 (16:52 -0700)]
pnpacpi: fix IRQ flag decoding
When decoding IRQ trigger mode and polarity, it is not enough to mask by
IORESOURCE_BITS because there are now additional bits defined. For
example, if IORESOURCE_IRQ_SHAREABLE was set, we failed to set *triggering
and *polarity at all.
I can't point to a failure that this patch fixes, but
bugs in this area have caused problems when resuming after
suspend, for example:
This is based on a patch by Tom Jaeger:
http://bugzilla.kernel.org/show_bug.cgi?id=9487#c32
[rene.herman@keyaccess.nl: fix comment] Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com>
thinkpad-acpi: fix LED handling on older ThinkPads
The less tested codepaths for LED handling, used on ThinkPads 570, 600e/x,
770e, 770x, A21e, A2xm/p, T20-22, X20 and maybe a few others, would write
data to kernel memory it had no business touching, for leds number 3 and
above. If one is lucky, that illegal write would cause an OOPS, but
chances are it would silently corrupt a byte.
The problem was introduced in commit af116101, "ACPI: thinkpad-acpi: add
sysfs led class support to thinkpad leds (v3.2)".
Fix the bug by refactoring the entire code to be far more obvious on what
it wants to do. Also do some defensive "constification".
Issue reported by Karol Lewandowski <lmctlx@gmail.com> (he's an lucky guy
and got an OOPS instead of silent corruption :-) ).
Root cause of the OOPS identified by Adrian Bunk <bunk@kernel.org>.
Thanks, Adrian!
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Tested-by: Karol Lewandowski <lmctlx@gmail.com> Signed-off-by: Len Brown <len.brown@intel.com>
Rework some subdriver init and exit handlers, in order to fix some
initialization error paths that were missing, or broken.
Hitting those bugs should be extremely rare in the real world, but should
that happen, thinkpad-acpi would fail to dealocate some resources and a
reboot might well be needed to be able to load the driver again.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Len Brown <len.brown@intel.com>
cpuidle and acpi driver interaction bug with the way cpuidle_register_driver()
is called. Due to this bug, there will be oops on
AC<->DC on some systems, where they support C-states in one DC and not in AC.
The current code does
ON BOOT:
Look at CST and other C-state info to see whether more than C1 is
supported. If it is, then acpi processor_idle does a
cpuidle_register_driver() call, which internally enables the device.
ON CST change notification (AC<->DC) and on suspend-resume:
acpi driver temporarily disables device, updates the device with
any new C-states, and reenables the device.
The problem is is on boot, there are no C2, C3 states supported and we skip
the register. Later on AC<->DC, we may get a CST notification and we try
to reevaluate CST and enabled the device, without actually registering it.
This causes breakage as we try to create /sys fs sub directory, without the
parent directory which is created at register time.
Thanks to Sanjeev for reporting the problem here.
http://bugzilla.kernel.org/show_bug.cgi?id=10394
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Zhao Yakui [Wed, 14 May 2008 03:32:59 +0000 (11:32 +0800)]
ACPI: Disable Fixed_RTC event when installing RTC handler
The Fixed_RTC event should be disabled when installing RTC handler.
Only when RTC alarm is set will it be enabled again. If it is not
disabled, maybe some machines will be powered on automatically after
the system is shutdown even when the RTC alarm is not set.
http://bugzilla.kernel.org/show_bug.cgi?id=10010
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Linus Torvalds [Wed, 11 Jun 2008 17:35:44 +0000 (10:35 -0700)]
Merge branch 'kvm-updates-2.6.26' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm
* 'kvm-updates-2.6.26' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
KVM: MMU: Fix is_empty_shadow_page() check
KVM: MMU: Fix printk() format string
KVM: IOAPIC: only set remote_irr if interrupt was injected
KVM: MMU: reschedule during shadow teardown
KVM: VMX: Clear CR4.VMXE in hardware_disable
KVM: migrate PIT timer
KVM: ppc: Report bad GFNs
KVM: ppc: Use a read lock around MMU operations, and release it on error
KVM: ppc: Remove unmatched kunmap() call
KVM: ppc: add lwzx/stwz emulation
KVM: ppc: Remove duplicate function
KVM: s390: Fix race condition in kvm_s390_handle_wait
KVM: s390: Send program check on access error
KVM: s390: fix interrupt delivery
KVM: s390: handle machine checks when guest is running
KVM: s390: fix locking order problem in enable_sie
KVM: s390: use yield instead of schedule to implement diag 0x44
KVM: x86 emulator: fix hypercall return value on AMD
KVM: ia64: fix zero extending for mmio ld1/2/4 emulation in KVM
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] cifs: fix oops on mount when CONFIG_CIFS_DFS_UPCALL is enabled
[CIFS] Fix hang in mount when negprot causes server to kill tcp session
disable most mode changes on non-unix/non-cifsacl mounts
[CIFS] Correct incorrect obscure open flag
[CIFS] warn if both dynperm and cifsacl mount options specified
silently ignore ownership changes unless unix extensions are enabled or we're faking uid changes
[CIFS] remove trailing whitespace
when creating new inodes, use file_mode/dir_mode exclusively on mount without unix extensions
on non-posix shares, clear write bits in mode when ATTR_READONLY is set
[CIFS] remove unused variables
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
net: Fix routing tables with id > 255 for legacy software
sky2: Hold RTNL while calling dev_close()
s2io iomem annotations
atl1: fix suspend regression
qeth: start dev queue after tx drop error
qeth: Prepare-function to call s390dbf was wrong
qeth: reduce number of kernel messages
qeth: Use ccw_device_get_id().
qeth: layer 3 Oops in ip event handler
virtio: use callback on empty in virtio_net
virtio: virtio_net free transmit skbs in a timer
virtio: Fix typo in virtio_net_hdr comments
virtio_net: Fix skb->csum_start computation
ehea: set mac address fix
sfc: Recover from RX queue flush failure
add missing lance_* exports
ixgbe: fix typo
forcedeth: msi interrupts
ipsec: pfkey should ignore events when no listeners
pppoe: Unshare skb before anything else
...
net: Fix routing tables with id > 255 for legacy software
Most legacy software do not like tables > 255 as rtm_table is u8
so tb_id is sent &0xff and it is possible to mismatch for example
table 510 with table 254 (main).
This patch introduces RT_TABLE_COMPAT=252 so the code uses it if
tb_id > 255. It makes such old applications happy, new
ones are still able to use RTA_TABLE to get a proper table id.
Signed-off-by: Krzysztof Piotr Oledzki <ole@ans.pl> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Frank Blaschka [Fri, 6 Jun 2008 10:37:48 +0000 (12:37 +0200)]
qeth: start dev queue after tx drop error
In case the xmit function drop out with an error, we have to wake
the netdevice queue to start another xmit.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Peter Tiedemann [Fri, 6 Jun 2008 10:37:47 +0000 (12:37 +0200)]
qeth: Prepare-function to call s390dbf was wrong
Prepare-function to call s390dbf was wrong handling variable arguments.
This worked as macro but not as function any more.
Now using va_list processing.
Signed-off-by: Peter Tiedemann <ptiedem@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Rusty Russell [Sun, 8 Jun 2008 10:51:55 +0000 (20:51 +1000)]
virtio: use callback on empty in virtio_net
virtio_net uses a timer to free old transmitted packets, rather than
leaving callbacks enabled all the time. If the host promises to
always notify us when the transmit ring is empty, we can free packets
at that point and avoid the timer.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Mark McLoughlin [Sun, 8 Jun 2008 10:50:56 +0000 (20:50 +1000)]
virtio: virtio_net free transmit skbs in a timer
virtio_net currently only frees old transmit skbs just
before queueing new ones. If the queue is full, it then
enables interrupts and waits for notification that more
work has been performed.
However, a side-effect of this scheme is that there are
always xmit skbs left dangling when no new packets are
sent, against the Documentation/networking/driver.txt
guideline:
"... it is not allowed for your TX mitigation scheme
to let TX packets "hang out" in the TX ring unreclaimed
forever if no new TX packets are sent."
Add a timer to ensure that any time we queue new TX
skbs, we will shortly free them again.
This fixes an easily reproduced hang at shutdown where
iptables attempts to unload nf_conntrack and nf_conntrack
waits for an skb it is tracking to be freed, but virtio_net
never frees it.
Signed-off-by: Mark McLoughlin <markmc@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Mark McLoughlin [Sun, 8 Jun 2008 10:49:59 +0000 (20:49 +1000)]
virtio: Fix typo in virtio_net_hdr comments
Signed-off-by: Mark McLoughlin <markmc@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Mark McLoughlin [Sun, 8 Jun 2008 10:49:00 +0000 (20:49 +1000)]
virtio_net: Fix skb->csum_start computation
hdr->csum_start is the offset from the start of the ethernet
header to the transport layer checksum field. skb->csum_start
is the offset from skb->head.
skb_partial_csum_set() assumes that skb->data points to the
ethernet header - i.e. it computes skb->csum_start by adding
the headroom to hdr->csum_start.
Since eth_type_trans() skb_pull()s the ethernet header,
skb_partial_csum_set() should be called before
eth_type_trans().
(Without this patch, GSO packets from a guest to the world outside the
host are corrupted).
Signed-off-by: Mark McLoughlin <markmc@redhat.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
eHEA has to call firmware functions in order to change the mac address
of a logical port. This patch checks if the logical port is up
when calling the register / deregister mac address calls. If the port
is down these firmware calls would fail and are therefore not executed.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ayaz Abdulla [Mon, 9 Jun 2008 23:51:06 +0000 (16:51 -0700)]
forcedeth: msi interrupts
Add a workaround for lost MSI interrupts. There is a race condition in
the HW in which future interrupts could be missed. The workaround is to
toggle the MSI irq mask.
Added cleanup based on comments from Andrew Morton.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com> Cc: Manfred Spraul <manfred@colorfullife.com> Cc: Jeff Garzik <jeff@garzik.org> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Jamal Hadi Salim [Tue, 10 Jun 2008 21:25:34 +0000 (14:25 -0700)]
ipsec: pfkey should ignore events when no listeners
When pfkey has no km listeners, it still does a lot of work
before finding out there aint nobody out there.
If a tree falls in a forest and no one is around to hear it, does it make
a sound? In this case it makes a lot of noise:
With this short-circuit adding 10s of thousands of SAs using
netlink improves performance by ~10%.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6 / log