[ARM] 5006/1: Gumstix GPIO header fixup and defconfig fixup
This patch adds the include of the GPIO header needed to make gumstix
build. The defconfig is updated to 2.6.25 and disables PCMCIA since
that has not yet been implemented for gumstix.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a driver for the Quick Capture Interface on the PXA270.
It is based on the original driver from Intel, but has been re-worked
multiple times since then, now it also supports the V4L2 API.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sat, 19 Apr 2008 15:46:54 +0000 (16:46 +0100)]
[ARM] pxa: restrict availability of pxa2xx PCMCIA drivers
Not all PXA2xx platforms provide the necessary support files for
PCMCIA to work, let alone build. Stop the build errors by making
PXA2xx PCMCIA support only available on those platforms which have
supplied the support files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: eric miao <eric.y.miao@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mark Brown [Tue, 15 Apr 2008 14:50:49 +0000 (15:50 +0100)]
[ARM] 4976/1: zylonite: Configure GPIO for WM9713 IRQ line
Set up the IRQ line for the WM9713 device on the Zylonite.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: eric miao <eric.y.miao@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ARM] 4971/1: pxaficp_ir: provide startup and shutdown hooks
Let platform do some specific initialisation and cleanup
things during pxaficp_ir probing and removing. E.g. this
can be usefull to request/free gpios used by the platform
to control the transceiver.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Philipp Zabel [Sat, 12 Apr 2008 12:29:22 +0000 (13:29 +0100)]
[ARM] 4966/1: magician: add MFP pin configuration
Although the GPIO alternate functions should be correctly set
by the bootloader, configure them here to be sure.
To save power, FFUART/BTUART/STUART are left unconfigured (output, low)
until they are needed by pxaficp or the magician GSM chipset driver.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ARM] 4960/1: Rewrite tosa pin configuration to use MFP tables.
Clean up all pins configuration to use currently proposed MFP table
schema.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com> Acked-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All magician devices I've encountered so far have featured the Toppoly
TD028STEB1 display, so the Samsung LTP280QV support is untested.
The power-on sequence is not correct because pxafb doesn't yet support
enabling the LCD controller in the middle of the it.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mark Brown [Wed, 9 Apr 2008 10:32:21 +0000 (11:32 +0100)]
[ARM] 4946/1: pxa3xx: Print an error if we refuse to suspend
The PXA3xx will not suspend if there are no wakeup sources configured.
Print a diagnostic message to make it easier for the user to see what's
happening.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: eric miao <eric.y.miao@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mark Brown [Mon, 7 Apr 2008 16:16:34 +0000 (17:16 +0100)]
[ARM] 4901/3: mainstone: Register primary I2C bus
Mainstone has the primary I2C bus exposed for use on plugin modules.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: eric miao <eric.y.miao@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Jaya Kumar [Sat, 15 Mar 2008 04:11:07 +0000 (05:11 +0100)]
[ARM] 4867/1: Adds flash, udc, mci support for gumstix F boards
This patch implements support for Gumstix-F flash, udc and mci. Fixes since the last time are:
- Steve Sakoman as maintainer
- cleanup for udc and mci setup
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
eric miao [Wed, 23 Jan 2008 06:25:27 +0000 (14:25 +0800)]
[ARM] pxa: add partial keypad support for mainstone
This is partial because mainstone's keypad is really special, some of
the keys like '1', '2', ... are actually connected to two row/column
juntions, thus pressing '1' is equivalent to pressing 'A' & 'H'.
This is really brain damanged since it makes distinguishing between
pressing '1' and multiple keys pressing of 'A' & 'H' difficult.
So these special keys are not supported for the time being.
Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
eric miao [Tue, 11 Mar 2008 01:46:28 +0000 (09:46 +0800)]
[ARM] pxa: allow dynamic enable/disable of GPIO wakeup for pxa{25x,27x}
Changes include:
1. rename MFP_LPM_WAKEUP_ENABLE into MFP_LPM_CAN_WAKEUP to indicate
the board capability of this pin to wakeup the system
2. add gpio_set_wake() and keypad_set_wake() to allow dynamically
enable/disable wakeup from GPIOs and keypad GPIO
* these functions are currently kept in mfp-pxa2xx.c due to their
dependency to the MFP configuration
3. pxa2xx_mfp_config() only gives early warning if MFP_LPM_CAN_WAKEUP
is set on incorrect pins
So that the GPIO's wakeup capability is now decided by the following:
a) processor's capability: (only those GPIOs which have dedicated
bits within PWER/PRER/PFER can wakeup the system), this is
initialized by pxa{25x,27x}_init_mfp()
b) board design decides:
- whether the pin is designed to wakeup the system (some of
the GPIOs are configured as other functions, which is not
intended to be a wakeup source), by OR'ing the pin config
with MFP_LPM_CAN_WAKEUP
- which edge the pin is designed to wakeup the system, this
may depends on external peripherals/connections, which is
totally board specific; this is indicated by MFP_LPM_EDGE_*
c) the corresponding device's (most likely the gpio_keys.c) wakeup
attribute:
Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
this is removed as low power state has already been encoded in
the pin configuration definitions.
Note: there is no specific reason for some of the GPIOs to drive
high in low power mode as indicated by the above setting, those
bits are ignored, and the result is validated to work.
2. the following code to configure GPIO wakeup is removed as this
is now totally handled by pxa2xx_mfp_config():
eric miao [Wed, 5 Mar 2008 09:16:29 +0000 (17:16 +0800)]
[ARM] pxa: add MFP-alike pin configuration support for pxa{25x, 27x}
Pin configuration on pxa{25x,27x} has now separated from generic GPIO
into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed
from pxa3xx and is used here to alert the difference between the two
concepts: pin configuration and generic GPIOs. A GPIO can be called
a "GPIO" _only_ when the corresponding pin is configured so.
A pin configuration on pxa{25x,27x} is composed of:
- alternate function selection (or pin mux as commonly called)
- low power state or sleep state
- wakeup enabling from low power mode
The following MFP_xxx bit definitions in mfp.h are re-used:
Selecting alternate function on pxa{25x, 27x} involves configuration
of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT}
are introduced. And pin configurations are defined by the following
two macros:
- MFP_CFG_IN : for input alternate functions
- MFP_CFG_OUT : for output alternate functions
Every configuration should provide a low power state if it configured
as output using MFP_CFG_OUT(). As a general guideline, the low power
state should be decided to minimize the overall power dissipation. As
an example, it is better to drive the pin as high level in low power
mode if the GPIO is configured as an active low chip select.
Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid
side effects when it is firstly configured as output. The actual
direction of the GPIO is configured by gpio_direction_{input, output}
Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus
the device based enable_irq_wake() mechanism is not applicable here.
E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following
code to enable OTG wakeup is by no means portable and intuitive, and
it is valid _only_ when GPIO35 is configured as USB_P2_1:
enable_irq_wake( gpio_to_irq(35) );
To make things worse, not every GPIO is able to wakeup the system.
Only a small number of them can, on either rising or falling edge,
or when level is high (for keypad GPIOs).
Thus, another new bit is introduced to indicate that the GPIO will
wakeup the system:
- MFP_LPM_WAKEUP_ENABLE
The following macros can be used in platform code, and be OR'ed to
the GPIO configuration to enable its wakeup:
eric miao [Mon, 3 Mar 2008 01:44:25 +0000 (09:44 +0800)]
[ARM] pxa: separate GPIOs and their mode definitions to pxa2xx-gpio.h
two reasons:
1. GPIO namings and their mode definitions are conceptually not part
of the PXA register definitions
2. this is actually a temporary move in the transition of PXA2xx to
use MFP-alike APIs (as what PXA3xx is now doing), so that legacy
code will still work and new code can be added in step by step
Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
eric miao [Mon, 4 Feb 2008 02:07:09 +0000 (10:07 +0800)]
[ARM] pxa: move mfp sysdev registeration out for suspend/resume order
MFP configurations after resume should be done before the GPIO registers
are restored. Move the mfp sysdev registeration to the same place where
GPIO and IRQ sysdev(s) are registered to better control the order.
Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
eric miao [Tue, 4 Mar 2008 09:18:38 +0000 (17:18 +0800)]
[ARM] pxa: make pxa_gpio_irq_type() processor generic
The main issue here is that pxa3xx does not have GAFRx registers,
access directly to these registers should be avoided for pxa3xx:
1. introduce __gpio_is_occupied() to indicate the GAFRx and GPDRx
registers are already configured on pxa{25x,27x} while returns
0 always on pxa3xx
2. pxa_gpio_mode(gpio | GPIO_IN) is replaced directly with assign-
ment of GPDRx, the side effect of this change is that the pin
_must_ be configured before use, pxa_gpio_irq_type() will not
change the pin to GPIO, as this restriction is sane, esp. with
the new MFP framework
Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
eric miao [Tue, 4 Mar 2008 05:53:05 +0000 (13:53 +0800)]
[ARM] pxa: integrate low IRQ chip (ICIP) and high IRQ chip (ICIP2) into one
This makes the code better organized and simplified a bit. The change
will lose a bit of performance when performing IRQ ack/mask/unmask,but
that's not too much after checking the result binary.
This patch also removes the ugly #ifdef CONFIG_PXA27x .. #endif by
carefully not to access those pxa{27x,3xx} specific registers, this
is done by keeping an internal IRQ number variable. The pxa-regs.h
is also modified so registers for IRQ > PXA_IRQ(31) are made public
even if CONFIG_PXA{27x,3xx} isn't defined (for pxa25x's sake)
The incorrect assumption in the original code that internal irq starts
from 0 is also corrected by comparing with PXA_IRQ(0).
"struct sys_device" for the IRQ are reduced into one single device on
pxa{27x,3xx}.
Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mark Brown [Tue, 4 Mar 2008 10:14:24 +0000 (11:14 +0100)]
[ARM] 4834/3: Convert ASoC pxa2xx-ac97 driver to use the clock API
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Takashi Iwai <tiwai@suse.de> Acked-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mark Brown [Tue, 4 Mar 2008 10:14:25 +0000 (11:14 +0100)]
[ARM] 4833/3: Convert non-SoC PXA2xx AC97 driver to clock API
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Takashi Iwai <tiwai@suse.de> Acked-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mark Brown [Tue, 4 Mar 2008 10:14:23 +0000 (11:14 +0100)]
[ARM] 4832/2: Support AC97CLK on PXA3xx via the clock API
The AC97 clock rate on PXA3xx is generated with a configurable divider
from sys_pll.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mark Brown [Tue, 4 Mar 2008 10:14:22 +0000 (11:14 +0100)]
[ARM] 4831/2: Add PXA2xx AC97 clocks to clock API
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Bjorn Helgaas [Tue, 25 Mar 2008 17:21:11 +0000 (11:21 -0600)]
ACPI: fix Medion _PRT quirk (use "ISA_", not "ISA")
This fixes the builtin RTL8139 NIC on the Medion MD9580-F laptop. The
BIOS reports the interrupt routing incorrectly. I recently added a
quirk to work around this, and this patch fixes a typo in the quirk.
We pad every ACPI pathname component to four characters, so ".ISA." will
never match anything. We need ".ISA_." instead.
Thank you Johann-Nikolaus Andreae <johann-nikolaus.andreae@nacs.de>
for patiently testing this patch.
See http://bugzilla.kernel.org/show_bug.cgi?id=4773
Linus Torvalds [Tue, 25 Mar 2008 16:06:44 +0000 (09:06 -0700)]
Merge branch 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c: Fix docbook problem
ASoC/TLV320AIC3X: Stop I2C driver ID abuse
i2c-omap: Fix unhandled fault
i2c-bfin-twi: Disable BF54x support for now
Linus Torvalds [Tue, 25 Mar 2008 15:57:47 +0000 (08:57 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
[PATCH] get stack footprint of pathname resolution back to relative sanity
[PATCH] double iput() on failure exit in hugetlb
[PATCH] double dput() on failure exit in tiny-shmem
[PATCH] fix up new filp allocators
[PATCH] check for null vfsmount in dentry_open()
[PATCH] reiserfs: eliminate private use of struct file in xattr
[PATCH] sanitize hppfs
hppfs pass vfsmount to dentry_open()
[PATCH] restore export of do_kern_mount()
Avi Kivity [Sun, 23 Mar 2008 12:21:08 +0000 (14:21 +0200)]
KVM: MMU: Fix memory leak on guest demand faults
While backporting 72dc67a69690288538142df73a7e3ac66fea68dc, a gfn_to_page()
call was duplicated instead of moved (due to an unrelated patch not being
present in mainline). This caused a page reference leak, resulting in a
fairly massive memory leak.
Fix by removing the extraneous gfn_to_page() call.
Avi Kivity [Sun, 16 Mar 2008 16:48:26 +0000 (18:48 +0200)]
KVM: VMX: Restore tss even on x86_64
The vmx hardware state restore restores the tss selector and base address, but
not its length. Usually, this does not matter since most of the tss contents
is within the default length of 0x67. However, if a process is using ioperm()
to grant itself I/O port permissions, an additional bitmap within the tss,
but outside the default length is consulted. The effect is that the process
will receive a SIGSEGV instead of transparently accessing the port.
Fix by restoring the tss length. Note that i386 had this working already.
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: Fix cut-and-paste error in rtl8150.c
USB: ehci: stop vt6212 bus hogging
USB: sierra: add another device id
USB: sierra: dma fixes
USB: add support for Motorola ROKR Z6 cellphone in mass storage mode
USB: isd200: fix memory leak in isd200_get_inquiry_data
USB: pl2303: another product ID
USB: new quirk flag to avoid Set-Interface
USB: fix gadgetfs class request delegation
PCIE has a mechanism to wait for Non-Posted request to complete. I think
pci_disable_device is a good place to do this.
Signed-off-by: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Due to the regression reported at
http://bugzilla.kernel.org/show_bug.cgi?id=10065
Cc: Shaohua Li <shaohua.li@intel.com> Cc: Soeren Sonnenburg <kernel@nn7.de> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mark Gross [Tue, 4 Mar 2008 22:59:31 +0000 (14:59 -0800)]
PCI: iova: lockdep false alarm fix
lockdep goes off on the iova copy_reserved_iova() because it and a function
it calls grabs locks in the from, and the to of the copy operation.
The function grab locks of the same lock classes triggering the warning. The
first lock grabbed is for the constant reserved areas that is never accessed
after early boot. Technically you could do without grabbing the locks for the
"from" structure its copying reserved areas from.
But dropping the from locks to me looks wrong, even though it would be ok.
The affected code only runs in early boot as its setting up the DMAR
engines.
This patch gives the reserved_ioval_list locks special lockdep classes.
Signed-off-by: Mark Gross <mgross@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mapping of physical memory in UIO needs pgprot_noncached() to ensure
that IO memory is not cached. Without pgprot_noncached(), it (accidentally)
works on x86 and arm, but fails on PPC.
Rene Herman [Thu, 20 Mar 2008 07:58:16 +0000 (00:58 -0700)]
USB: ehci: stop vt6212 bus hogging
The VIA VT6212 defaults to only waiting 1us between passes over EHCI's
async ring, which hammers PCI badly ... and by preventing other devices
from accessing the bus, causes problems like drops in IDE throughput,
a problem that's been bugging users of those chips for several years.
A (partial) datasheet for this chip eventually turned up, letting us
see how to make it use a VIA-specific register to switch over to the
the normal 10us value instead, as suggested by the EHCI specification
Solution noted by Lev A. Melnikovsky.
It's not clear whether this register exists on other VIA chips; we
know that it's ineffective on the vt8235. So this patch only applies
to chips that seem to be incarnations of the (discrete) vt6212.
Signed-off-by: Rene Herman <rene.herman@gmail.com> Tested-by: Lev A. Melnikovsky <melnikovsky@mail.ru> Tested-by: Alessandro Suardi <alessandro.suardi@gmail.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Fri, 14 Mar 2008 07:53:24 +0000 (00:53 -0700)]
USB: sierra: dma fixes
while I was adding autosuspend to that driver I noticed a few issues.
You were having DMAed buffers as a part of a structure.
This will fail on platforms that are not DMA-coherent (arm, sparc, ppc, ...)
Please test this patch to fix it.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: add support for Motorola ROKR Z6 cellphone in mass storage mode
Motorola ROKR Z6 cellphone has bugs in its USB, so it is impossible to use
it as mass storage. Patch describes new "unusual" USB device for it with
FIX_INQUIRY and FIX_CAPACITY flags and new BULK_IGNORE_TAG flag.
Last flag relaxes check for equality of bcs->Tag and us->tag in
usb_stor_Bulk_transport routine.
Signed-off-by: Constantin Baranov <const@tltsu.ru> Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: Daniel Drake <dsd@gentoo.org> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Max Arnold [Thu, 20 Mar 2008 09:43:56 +0000 (16:43 +0700)]
USB: pl2303: another product ID
Device like this http://aldiga.com/english/A-100-USB-EDGE10.htm
contains Prolific 2303 chip.
Actually their site a bit outdated - I have AlDiga AL-11U
GSM/GPRS/EDGE modem and it works with pl2303 module after adding
corresponding product ID.
By default modem uses baud rate 460800. GSM chipset - SIMCom SIM600,
quad band 850/900/1800/1900 MHz
Alan Stern [Tue, 11 Mar 2008 14:20:12 +0000 (10:20 -0400)]
USB: new quirk flag to avoid Set-Interface
This patch (as1057) fixes a problem with the X-Rite/Gretag-Macbeth
Eye-One Pro display colorimeter; the device crashes when it receives a
Set-Interface request. A new quirk (USB_QUIRK_NO_SET_INTF) is
introduced and a quirks entry is created for this device.
Roy Hashimoto [Wed, 12 Mar 2008 21:55:31 +0000 (13:55 -0800)]
USB: fix gadgetfs class request delegation
gadgetfs (drivers/usb/gadget/inode.c) was not delegating all
non-device requests to userspace. This patch makes the handling of
all request cases consistent.
Signed-off-by: Roy Hashimoto <hashimot@alumni.caltech.edu> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Linus Torvalds [Tue, 25 Mar 2008 03:35:48 +0000 (20:35 -0700)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] mpc5200: Fix incorrect compatible string for the mdio node
[POWERPC] Update some defconfigs
Linus Torvalds [Tue, 25 Mar 2008 03:02:32 +0000 (20:02 -0700)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] ahci: SB600 workaround is suspect... play it safe for now
sata_promise: fix hardreset hotplug events, take 2
libata: improve HPA error handling
libata: assume no device is attached if both IDENTIFYs are aborted
pata_it821x: use raw nbytes in check_atapi_dma
libata: implement ata_qc_raw_nbytes()
projects / linux-2.6 / log