<qualifier> void * is not the same as void <qualifier> *... Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] m68knommu: extract common timer code for 68EZ328 processor
Rework the 68x328 configuration and setup code. All 68x328 varients
share the same timer hardware. So extract that into its own file,
instead of keeping copies in each processors setup code.
[PATCH] m68knommu: register map setup for MOD5272 board
The boot loader on the MOD5272 board doesn't set the register maping,
so set it in the 5272 init code. There was code in there to support
this, but we had never needed to use it before.
[PATCH] m68knommu: extract common timer code for 68328 processor
Rework the 68x328 configuration and setup code. All 68x328 varient
share the same timer hardware, so extract that into its own file,
instead of keeping copies in each processors setup code.
Henk [Tue, 16 Aug 2005 14:17:43 +0000 (16:17 +0200)]
[PATCH] input-driver-yealink-P1K-usb-phone
This patch aggregates all modifications in the -mm tree and adds
complete ringtone support.
The following features are supported:
- keyboard full support
- LCD full support
- LED full support
- dialtone full support
- ringtone full support
- audio playback via generic usb audio diver
- audio record via generic usb audio diver
For driver documentation see: Documentation/input/yealink.txt
For vendor documentation see: http://yealink.com
Nick Sillik [Wed, 17 Aug 2005 17:37:34 +0000 (13:37 -0400)]
[PATCH] USB Storage: code cleanups for onetouch.c
As sugested by Alan Stern here are a few code cleanups for onetouch.c:
-Check number of endpoints before directly referencing intf->endpoint[2]
-Use defined constants instead of magic numbers
-Revmove the non-ascii characters from copyright notice
-Make registration and deregistration messages more similar
Signed-off-by: Nick Sillik <n.sillik@temple.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pete Zaitcev [Mon, 15 Aug 2005 23:53:57 +0000 (16:53 -0700)]
[PATCH] usbmon in 2.6.13: peeking into DMA areas
This code looks at urb->transfer_dma, maps the page and takes the data.
I am looking for volunteers to contribute architectures other than i386
or to develop an architecure-neutral API for it (or point me that it
was done already).
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the field tt_usecs to ehci_qh and ehci_iso_stream, and sets it
appropriately when setting them up as periodic endpoints. It records
the transation translator's think_time (added in last patch) plus the
downstream (i.e. low or full speed) bustime of the transfer associated
with each interrupt or iso frame, as calculated by usb_calc_bus_time.
Signed-off-by: Dan Streetman <ddstreet@ieee.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 31 Aug 2005 16:54:50 +0000 (09:54 -0700)]
[PATCH] USB: usbnet (9/9) module for pl2301/2302 cables
This wraps up the conversion of the "usbnet" driver structure, by
moving the Prolific PL-2201/2302 minidriver to a module of its own.
It also includes some minor cleanups to the remaining "usbnet" file,
notably removing that long changelog at the top.
Minor historical note: Linux 2.2 first called the driver for
this hardware "plusb".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 31 Aug 2005 16:54:36 +0000 (09:54 -0700)]
[PATCH] USB: usbnet (8/9) module for RNDIS devices
This adds host-side RNDIS support to the "usbnet" driver, so Linux can talk
to various devices (often based on WinCE) that otherwise only Windows could
talk to.
Tested with little-endian Linux talking to a Linux-USB Ethernet/RNDIS based
peripheral. This also includes updates from Eddie C. Dost <ecd@brainaid.de>
for big-endian SPARC Linux talking to a Nokia 9500 Communicator.
It's still marked as EXPERIMENTAL because this code is so young. This
ought to let Linux to work with various cable modems that previously
would have been "Windows Only".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 31 Aug 2005 16:54:20 +0000 (09:54 -0700)]
[PATCH] USB: usbnet (7/9) module for CDC Ethernet
Makes the CDC Ethernet support live in a separate driver module.
This module is a bit special since it exports utility functions
that are reused by the the Zaurus and RNDIS drivers, but it's
not "core" like usbnet itself.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 31 Aug 2005 16:53:58 +0000 (09:53 -0700)]
[PATCH] USB: usbnet (6/9) module for Zaurii and compatibles
This moves usbnet support for Zaurus and compatibles into its own module.
Other than exporting a couple of helper functions, this just involved
shuffling some code and updating the comments.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 31 Aug 2005 16:53:42 +0000 (09:53 -0700)]
[PATCH] USB: usbnet (5/9) module for genesys gl620a cables
This moves the GeneSys GL620USB-A support into its own driver file.
It also fixes a "return wrong skb" glitch in the rx unbatching, as
recently reported, and adds some missing byteswaps in the special
"genelink" headers (so it might now work on big-endian Linux).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 31 Aug 2005 16:53:26 +0000 (09:53 -0700)]
[PATCH] USB: usbnet (4/9) module for net1080 cables
As with the "cdc_subset" and "asix" drivers, this just moves the net1080
support into its one driver module. In this case there's a small bit of
extra cleanup involved, moving some funky framing logic into the tx_fixup()
routine (resolving a long overdue FIXME).
Minor historical note: "usbnet" started out as "net1080", then got
generalized to make it easier for other network drivers to reuse the
urb queueing and fault management code here.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 31 Aug 2005 16:53:10 +0000 (09:53 -0700)]
[PATCH] USB: usbnet (3/9) module for ASIX Ethernet adapters
This patch moves the ASIX AX8817x driver into its own file, just using
the "usbnet" infrastructure as a utility library.
- As with "cdc_subset" this involved minor Kconfig/kbuild tweaks,
moving code from one file to another, and exporting a few functions.
- This includes updates from Jamie Painter to add (and use) a new hook
to handle the different maximum transfer sizes for rx and tx sides.
- Also from Jamie, some bugfixes:
* MDIO byteorder (to address some PPC media negotiation problems);
* Force alignment at key spots when using ax88772 framing (on some
embedded hardware, the network stack will break otherwise);
* Address some link reset problems.
It also makes this driver use the standard (5 seconds vs half second)
control timeouts used elsewhere in USB; and wraps a few lines before
the 80th column (which previously needed it).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 31 Aug 2005 16:52:45 +0000 (09:52 -0700)]
[PATCH] USB: usbnet (2/9) module for simple network links
This patch creates the first of several separate "minidriver" modules
for "usbnet". This one handles only the very simplest hardware, which
can be handled almost entirely by the "usbnet" core.
- Move device-specific bits into new "cdc_subset.c" driver,
shrinking "usbnet" by a bunch;
- Export the functions needed to support this minidriver
(with EXPORT_SYMBOL_GPL);
- Update Kconfig and kbuild accordingly.
This one handles about a dozen different device types, with the most
notable ones being Gumstix and most Linux-based PDAs (except Zaurus
running that ancient code from Sharp).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 31 Aug 2005 16:52:31 +0000 (09:52 -0700)]
[PATCH] USB: usbnet (1/9) clean up framing
This starts to prepare the core of "usbnet" to know less about various
framing protocols that map Ethernet packets onto USB, so "minidrivers"
can be modules that just plug into the core.
- Remove some framing-specific code that cluttered the core:
* net->hard_header_len records how much space to preallocate;
now drivers that add their own framing (Net1080, GeneLink,
Zaurus, and RNDIS) will have smoother TX paths. Even for
the drivers (Zaurus, Net1080) that need trailers.
* defines new dev->hard_mtu, using this "hardware" limit to
check changes to the link's settable "software" mtu.
* now net->hard_header_len and dev->hard_mtu are set up in the
driver bind() routines, if needed.
- Transaction ID is no longer specific to the Net1080 framing;
RNDIS needs one too.
- Creates a new "usbnet.h" header with declarations that are shared
between the core and what will be separate modules.
- Plus a couple other minor tweaks, like recognizing -ESHUTDOWN
means the keventd work should just shut itself down asap.
The core code is only about 1/3 of this large file. Splitting out the
minidrivers into separate modules (e.g. ones for ASIX adapters,
Zaurii and similar, CDC Ethernet, etc), in later patches, will
improve maintainability and shrink typical runtime footprints.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alexey Dobriyan [Sun, 14 Aug 2005 13:24:26 +0000 (17:24 +0400)]
[PATCH] USB ldusb: fmt warnings fixes for 64-bit platforms
Fix
drivers/usb/misc/ldusb.c: In function `ld_usb_read':
drivers/usb/misc/ldusb.c:467: warning: int format, different type arg (arg 4)
drivers/usb/misc/ldusb.c: In function `ld_usb_write':
drivers/usb/misc/ldusb.c:531: warning: int format, different type arg (arg 4)
drivers/usb/misc/ldusb.c:532: warning: int format, different type arg (arg 5)
drivers/usb/misc/ldusb.c:532: warning: int format, different type arg (arg 6)
Dale Farnsworth [Thu, 11 Aug 2005 00:25:25 +0000 (17:25 -0700)]
[PATCH] USB: remove include of asm/usb.h in ohci-ppc-soc.c
ohci-ppc-soc.c provides for a platform-specific callback mechanism for
when the HC is successfully probed or removed. It turned out that none
of the 3 platforms using it need this facility. Also the required
include/asm-ppc/usb.h has never been accepted. This patch removes the
callback feature and the include of <asm/usb.h>.
Alan Stern [Thu, 11 Aug 2005 19:50:32 +0000 (15:50 -0400)]
[PATCH] USB: Support unbinding of the usb_generic driver
This patch (as556) adds support for unbinding the usb_generic "driver".
That driver only binds to USB devices, as opposed to interfaces, and it
does nothing much besides marking which struct device's go with an
overall USB device plus providing suspend/resume methods. Now that
users can unbind drivers at will using the sysfs "unbind" attribute, we
need a rational way of dealing with USB devices that are no longer under
full control of the USB stack. The patch handles this by unconfiguring
the device, thereby removing all the interfaces and their associated
drivers and children.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Thu, 11 Aug 2005 14:15:39 +0000 (10:15 -0400)]
[PATCH] USB: Add timeout to usb_lock_device_for_reset
This patch (as555) modifies the already-awkward
usb_lock_device_for_reset routine in usbcore by adding a timeout. The
whole point of the routine is that the caller wants to acquire some
semaphores in the wrong order; protecting against the possibility of
deadlock by timing out seems only prudent.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Wed, 10 Aug 2005 21:12:31 +0000 (17:12 -0400)]
[PATCH] USB: Disconnect children when unbinding the hub driver
This patch (as554) makes the hub driver disconnect any child USB devices
when it is unbound from a hub. Normally this will never happen, but
there are a few oddball ways to unbind the hub driver while leaving the
children intact. For example, the new "unbind" sysfs attribute can be
used for this purpose.
Given that unbinding hubs with children is now safe, the patch also
removes the code that prevented people from doing so using usbfs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Daniel Drake [Wed, 10 Aug 2005 17:30:04 +0000 (18:30 +0100)]
[PATCH] USB: Fix HP8200 detection in shuttle_usbat
Adding flash-device support to the shuttle_usbat driver in 2.6.11
introduced the need to detect which type of device we are dealing with:
CDRW drive, or flash media reader.
The detection routine used turned out to not work for HP8200 CDRW users,
who saw their devices being detected as a flash disk.
This patch (which has been tested on both flash and cdrom) removes some
unnecessary code, moves device detection to much later during
initialization, and introduces a new detection routine which appears to
work.
Signed-off-by: Daniel Drake <dsd@gentoo.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 29 Jul 2005 20:11:07 +0000 (16:11 -0400)]
[PATCH] USB: URB_ASYNC_UNLINK flag removed from the kernel
29 July 2005, Cambridge, MA:
This afternoon Alan Stern submitted a patch to remove the URB_ASYNC_UNLINK
flag from the Linux kernel. Mr. Stern explained, "This flag is a relic
from an earlier, less-well-designed system. For over a year it hasn't
been used for anything other than printing warning messages."
An anonymous spokesman for the Linux kernel development community
commented, "This is exactly the sort of thing we see happening all the
time. As the kernel evolves, support for old techniques and old code can
be jettisoned and replaced by newer, better approaches. Proprietary
operating systems do not have the freedom or flexibility to change so
quickly."
Mr. Stern, a staff member at Harvard University's Rowland Institute who
works on Linux only as a hobby, noted that the patch (labelled as548) did
not update two files, keyspan.c and option.c, in the USB drivers' "serial"
subdirectory. "Those files need more extensive changes," he remarked.
"They examine the status field of several URBs at times when they're not
supposed to. That will need to be fixed before the URB_ASYNC_UNLINK flag
is removed."
Greg Kroah-Hartman, the kernel maintainer responsible for overseeing all
of Linux's USB drivers, did not respond to our inquiries or return our
calls. His only comment was "Applied, thanks."
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Matthew Dharm [Thu, 28 Jul 2005 21:50:29 +0000 (14:50 -0700)]
[PATCH] USB Storage: wedge SCSI revision at 2 for usb-storage devices
This patch started life as as479b, and has been rediffed. Please note
the order of submission of this latest patch series -- even tho this has
an older original number, it is the last patch I'll be sending today.
This patch changes the reported SCSI revision level to 2 for all
disk-type devices. This is needed in a few cases because the device
reports a level of 3 or higher but then crashes when given a REPORT LUNS
command (for which support is supposed to be mandatory at those levels).
This shouldn't harm us, since it only matters for sparse LUNs and we
have separate ways of coping with that.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Matthew Dharm [Thu, 28 Jul 2005 21:49:01 +0000 (14:49 -0700)]
[PATCH] USB Storage: add support for Maxtor One-Touch button
This patch is originally from Nick Sillik, and has been rediffed against
the latest tree.
This patch adds usability to the OneTouch Button on Maxtor External USB
Hard Drives. Using an unusual device entry it declares an extra init
function which claims the interrupt endpoint associated with this
button. The button is connected to the input system.
Signed-off-by: Nick Sillik <n.sillik@temple.edu> Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Matthew Dharm [Thu, 28 Jul 2005 21:45:50 +0000 (14:45 -0700)]
[PATCH] USB Storage: close a race condition in disconnect near queuecommand
This patch started life as as534, and has been re-diffed against the latest
tree.
usb-storage has a small loophole, a window between the time queuecommand
accepts a new command and the time the control thread starts to execute
it. If disconnect is called during that window, the driver won't cancel
the pending command -- we've been relying on the SCSI core to cancel it
for us during host removal. But it's better for usb-storage to cancel
it; this avoids races and reduces reliance on the SCSI core.
Fortunately cancelling these commands is easy to do; the key is to do it
_before_ calling scsi_remove_host.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Matthew Dharm [Thu, 28 Jul 2005 21:44:29 +0000 (14:44 -0700)]
[PATCH] USB Storage: close a race condition in disconnect near probe
This patch started life as as533, and has been re-diffed against the
current tree.
Disconnect processing in usb-storage naturally divides into two parts:
one to quiesce the driver (make sure no commands are executing or
queued) and remove the host, and the other to deallocate all the USB and
non-USB resources. This patch creates two subroutines to handle those
two parts. Mostly it's just code movement, but there is one significant
change. If the scsi-scanning thread fails to initialize but the host
has successfully been added, we need to quiesce the driver before
removing the host. After all, it's possible that scanning could have
been initiated from somewhere else, such as userspace -- very low
probability, but it's easily handled by calling the new subroutine.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Matthew Dharm [Thu, 28 Jul 2005 21:43:08 +0000 (14:43 -0700)]
[PATCH] USB Storage: remove dependency on SCSI-provided serial/tag number
This patch started life as as531 from Alan Stern. It has been rediffed
against the latest tree.
The SCSI people have deprecated the use of scsi_cmnd.serial_number for
anything other than printk. Worse than that, the SCSI core doesn't
always increment the number (when the error handler is running, for
example). So this patch creates a locally-stored value for use in
bulk-only tags. The net result is a simplification, since we no longer
have to save & restore the serial_number value while autosensing.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Olav Kongas [Fri, 5 Aug 2005 11:23:35 +0000 (14:23 +0300)]
[PATCH] USB: Switch isp116x-hcd over to root hub interrupt
Switch isp116x-hcd over from root hub polling to interrupt. This change closes
also a race that was present with the old polling scheme: status polling could
happen in a time window, where root hub status bits were not stable.
Signed-off-by: Olav Kongas <ok@artecdesign.ee> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Olav Kongas [Thu, 4 Aug 2005 14:02:54 +0000 (17:02 +0300)]
[PATCH] USB: isp116x-hcd: remove clock() and reset()
This patch removes support for user-provided platform-specific hardware reset
and clock starting/stopping functions. Hardware reset was needed earlier as
getting the software reset working was tricky due to the lack of documentation.
Recently, a number of people using isp116x have said the software reset is
working for them.
I haven't heard of anybody using the clock starting/stopping.
Signed-off-by: Olav Kongas <ok@artecdesign.ee> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Randy Dunlap [Mon, 1 Aug 2005 03:41:19 +0000 (20:41 -0700)]
[PATCH] USB usblp: rate-limit printer status error messages
Rate-limit usblp printer error status messages.
I unplugged my USB printer and almost instantly got several hundred
of these in my kernel message log:
drivers/usb/class/usblp.c: usblp0: error -19 reading printer status
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pete Zaitcev [Mon, 15 Aug 2005 04:16:03 +0000 (21:16 -0700)]
[PATCH] USB: ub 4: Zaitcev's quasi-S/G
Back out Axboe-style quasi-S/G and replace it with one command and
repeated URBs. This is similar to what usb-storage does, only instead
of a few URBs allocated together, one URB is reused.
Jens's idea was very nice, but it collapsed when I had to support
packet commads for CD burning. I cannot issue two or more packet
commands where application expected only one.
However, burning does not work completely yet. The cdrecord starts,
recognizes the device, then aborts without writing a TOC.
Signed-off-by: Pete Zaitcev <zaitcev@yahoo.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pete Zaitcev [Sun, 31 Jul 2005 05:51:52 +0000 (22:51 -0700)]
[PATCH] USB: ub 3/3: death to ub_bd_rq_fn_1
When Al Viro saw the ub.c, he observed that it was a proof positive of
Linus not reading patches anymore: names like fo_ob_ar_ba_2 used to
cause serious fireworks. In my defence, any good scheme can be pushed
to the realm of absurd if pushed far enough.
Signed-off-by: Pete Zaitcev <zaitcev@yahoo.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pete Zaitcev [Sun, 31 Jul 2005 05:38:30 +0000 (22:38 -0700)]
[PATCH] USB: ub 1/3: Axboe's quasi-S/G
This the quasi-S/G patch for ub as suggested by Jens Axboe at OLS and
implemented that night before 4 a.m. Surprisingly, it worked right away...
Alas, I had to skip some OLS partying, but it was for the good cause.
Now the speed of ub is quite acceptable even on partitions with small
block size.
The ub does not really support S/G. Instead, it just tells the block
layer that it does. Then, most of the time, the block layer merges
requests and passes single-segmnent requests down to ub; everything
works as before. Very rarely ub gets an unmerged S/G request. In such
case, it issues several commands to the device.
I added a small array of counters to monitor the merging (sg_stat).
This may be dropped later.
Signed-off-by: Pete Zaitcev <zaitcev@yahoo.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[PATCH] usb-storage: Add IGNORE_RESIDUE flag for Mitsumi USB 2.0 card reader (VIA hardware)
This patch adds an entry in the unusual_devs.h file for a Mitsumi card
reader/floppy combo that uses a VIA chipset. The IGNORE_RESIDUE flag was
needed for the second LUN to operate properly.
Alan Stern [Wed, 10 Aug 2005 19:15:57 +0000 (15:15 -0400)]
[PATCH] USB: Fix regression in core/devio.c
This patch (as551) fixes another little problem recently added to the
USB core. Someone didn't fix the type of the first argument to
unregister_chrdev_region.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes libusb pick up the real nodes instead of the mounted usbfs:
export USB_DEVFS_PATH=/dev/bus/usb
Background:
All this makes it possible to manage usb devices with udev instead of
the devfs solution. We are currently working on a pam_console/resmgr
replacement driven by udev and a pam-helper. It applies ACL's to device
nodes, which is required for modern desktop functionalty like
"Fast User Switching" or multiple local login support.
New patch with its own major. I've succesfully disabled usbfs and use real
nodes only on my box. With: "export USB_DEVFS_PATH=/dev/bus/usb" libusb picks
up the udev managed nodes instead of reading usbfs files.
This makes udev to provide symlinks for libusb to pick up:
SUBSYSTEM="usb_device", PROGRAM="/sbin/usbdevice %k", SYMLINK="%c"
[PATCH] USB: Prevent hid-core claiming Apple Bluetooth device on new G4 powerbooks
To recap: My new G4 powerbook has a bluetooth device that boots up in
what apppears to be a compatability mode - it looks exactly like an HID
keyboard/mouse device.
A special command sequence is sent to switch it into full bluetooth
mode. When this occurs the original HID device vanishes, and a new
(bluetooth HID) USB device appears on the bus with a different product
ID.
The original thread is here:
http://sourceforge.net/mailarchive/message.php?msg_id=12532263
The attached patch adds the device to the hid-core quirks so that
hid-core ignores it.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ian Abbott [Tue, 2 Aug 2005 13:01:27 +0000 (14:01 +0100)]
[PATCH] USB ftdi_sio: New IDs for ELV, Xsens and Falcom products
This patch for the ftdi_sio driver adds a bunch of new devices and fixes
an incorrect PID:
o Fix PID for ELV UO100 (the PID was in fact for ELV UR100).
o Add PID ELV UR100 (see above) and ELV ALC 8500 Expert.
o Add a whole bunch of other PIDs for ELV USB devices, commented out for
now as they may be used by other drivers eventually. (Christian Abt
of ELV.de submitted a full list of devices including an indication of
which set of drivers are used by default in the MS Windows world. We
decided to comment out the devices that use FTDI's D2XX Windows
drivers by default.)
o Add PIDs for eight devices from Xsens Technologies BV (submitted in a
patch against 2.6.12.2 by Patrick Riphagen).
o Add PID for Falcom Samba GPRS modem (submitted by Sebastian Schubert).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dariusz M [Thu, 28 Jul 2005 16:06:13 +0000 (18:06 +0200)]
[PATCH] USB: pl2303 driver, makes pl2303HX chip work correctly
This trivial patch makes pl2303 driver work correctly with pl2303HX chip.
Apparently some bug in HX version of pl2303 makes the chip loose some
transmitted bytes or stop working at all after reception of
USB_REQ_CLEAR_FEATURE mesage. Logs generated by UsbSnoop application reveal
that windows driver does not send this type of messages to the converter.
This patch centralizes the assignment of bcdDevice numbers for different
gadget controllers. This won't improve the object code at all, but it
does save a lot of repetitive and error-prone source code ... and will
simplify the work of supporting a new controller driver, since most new
gadget drivers will no longer need patches (unless some hardware quirks
limit USB protocol messaging).
Added minor cleanups and identifer hooks for the UDC in the Freescale
iMX series processors.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch removes unneeded casts for the following (void *) pointers:
- tty_struct->driver_data
- void *private argument of usb_serial_port_softint()
Nicolas Pitre [Thu, 8 Sep 2005 22:07:40 +0000 (23:07 +0100)]
[ARM] 2892/1: remove gcc workaround for direct access to absolute memory addresses
Patch from Nicolas Pitre
It used to make a difference in the gcc-2.95 era. However these days
modern gcc apparently got better at not being influenced by such constructs
(which is good in general) and therefore such workaround is of no real
advantage anymore.
The good news is that gcc (from version 4.1.0) is now fixed with
regards to the defficiency this workaround was trying to address.
For those interested the patch can easily be backported to older gcc
versions and can be found here:
http://gcc.gnu.org/cgi-bin/cvsweb.cgi/gcc/gcc/config/arm/arm.c.diff?r1=1.476&r2=1.478
and also here:
http://savannah.gnu.org/cgi-bin/viewcvs/gcc/gcc/gcc/config/arm/arm.c.diff?r1=text&tr1=1.476&r2=text&tr2=1.478&diff_format=u
Signed-off-by: Nicolas Pitre <nico@cam.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tony Lindgren [Thu, 8 Sep 2005 22:07:38 +0000 (23:07 +0100)]
[ARM] 2890/1: OMAP 1/4: Update omap1 specific files, take 2
Patch from Tony Lindgren
This patch syncs the mainline kernel with linux-omap tree.
The highlights of the patch are:
- Convert more drivers to register resources in board-*.c to take
advantage of the driver model by David Brownell and Ladislav Michl
- Use set_irq_type() for GPIO interrupts instead of
omap_set_gpio_edge_ctrl() by David Brownell
- Add minimal support for handling optional add-on boards, such as
OSK Mistral board with LCD and keypad, by David Brownell
- Minimal support for loading functions to SRAM by Tony Lindgren
- Wake up from serial port by muxing RX lines temporarily into GPIO
interrupts by Tony Lindgren
- 32KHz sched_clock by Tony Lindgren and Juha Yrjola
Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Brett M Russ [Mon, 15 Aug 2005 19:23:41 +0000 (15:23 -0400)]
[PATCH] PCI/libata INTx cleanup
Simple cleanup to eliminate X copies of the pci_enable_intx() function
in libata. Moved ahci.c's pci_intx() to pci.c and use it throughout
libata and msi.c.
projects / linux-2.6 / log