Michael Krufky [Fri, 21 Dec 2007 14:18:32 +0000 (11:18 -0300)]
V4L/DVB (6881): include struct analog_demod_ops directly inside struct dvb_frontend
Rather than using a pointer, include struct analog_demod_ops directly
inside struct dvb_frontend. This will allow us to use dvb_attach in
the future, along with removing the need to check the ops structure
before having to check the pointer to the method being called.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Fri, 21 Dec 2007 05:55:43 +0000 (02:55 -0300)]
V4L/DVB (6879): move struct analog_tuner_ops into dvb_frontend.h
struct analog_tuner_ops no longer has any dependencies specific
to v4l2, so we can move this into dvb_frontend.h with the rest
of the tuning structures.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In my testing yesterday, I was using a scan file tailored specifically
for a unique test situation -- As it turns out, this scan file was bad,
and I will use the one included inside dvb-apps for testing for now on.
I've tested with other ATSC tuners just to confirm, using:
us-ATSC-center-frequencies-8VSB
Anyhow, as it turns out, the tuner-xc2028 *does* require a tuning offset
for ATSC. Even though the linux-dvb api passes in center frequencies
from userspace, apparantly the xceive firmware is already factoring in
the tuning offset to center.
In order to make the device function using the same scan files /
channels.conf configurations as other atsc devices, we must offset by
1.75 MHz.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Chris Pascoe [Sat, 15 Dec 2007 06:31:09 +0000 (03:31 -0300)]
V4L/DVB (6857): cx23885: correctly join I2C writes and reads from same address
When an I2C message specifies a write then a read from the same I2C address,
we need to tell the chip to not release the bus between the message parts.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Chris Pascoe [Sat, 15 Dec 2007 06:24:00 +0000 (03:24 -0300)]
V4L/DVB (6856): zl10353: improve tuning parameters and update register map
Some more I2C traces and a experimentation with register values on
both the ZL10353 and MT352 mean that I can now guess at what more
of the ZL10353 registers do.
Guess at the registers' names (based on the equivalent names in MT352)
and update set_parameters/get_parameters with the new knowledge.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It seems that the DTV78 firmware is intended for use in locations where
VHF channels have 7MHz bandwidth and UHF channels have 8MHz bandwidth.
If we switch to DTV78 firmware when we detect this condition, we can
avoid firmware reloads when switching between VHF and UHF transponders.
Place the state for this in the control structure so that card drivers
can hint to us to use DTV78 firmware from the first tuning attempt.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Chris Pascoe [Sun, 2 Dec 2007 12:39:18 +0000 (09:39 -0300)]
V4L/DVB (6854): xc2028: be more specific about when applying offset for 7MHz channels
We have been inserting a mystery 500kHz offset for tuning 7MHz channels,
however some experimentation reveals it is only needed under certain
conditions with specific firmware combinations. Document these and only
apply the offset when we know it is required.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Chris Pascoe [Sun, 2 Dec 2007 09:54:17 +0000 (06:54 -0300)]
V4L/DVB (6853): xc2028: check HAS_IF flag against table
When searching for the right S-Code table to load, check the HAS_IF flag
against the firmware we are checking instead of against the the "type"
requested. We already ignore the scode type requested if the caller passed
an int_freq; this makes the search by frequency consistent with that behaviour.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Chris Pascoe [Sun, 2 Dec 2007 09:36:42 +0000 (06:36 -0300)]
V4L/DVB (6852): xc2028: s-code offset should not modify internal control structure
Don't modify the control structure that was provided at attach when applying
an offset to the S-Code, otherwise it will be incorrect on subsequent tunes.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Aurelien Jarno [Mon, 17 Dec 2007 16:49:17 +0000 (13:49 -0300)]
V4L/DVB (em28xx): Add support for Pinnacle Dazzle DVC 100
The patch below adds the "Pinnacle Dazzle DVC 100" to the list of
cards supported by the em28xx driver. As the configuration is the same
as the DVC 90 one, it simply adds a new USB ID to the list of devices
supported by the DVC 90 configuration.
Michael Krufky [Sun, 16 Dec 2007 22:53:32 +0000 (19:53 -0300)]
V4L/DVB (6840): tuner: convert tda9887 to use TUNER_SET_CONFIG
Use TUNER_SET_CONFIG to set configuration in tda9887's private state
structure, rather than storing tda9887-specific configuration within
struct tuner.
Update handling of TUNER_SET_CONFIG by tuner-core, to call
&t->fe.ops.analog_demod_ops rather than &t->fe.ops.tuner_ops
analog_demod_ops.set_config passes the request to tuner_ops.set_config,
so this does not break other drivers.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Frej Drejhammar [Mon, 5 Nov 2007 20:57:11 +0000 (17:57 -0300)]
V4L/DVB (6834): cx88-video: Enable selection of the WM8775 for cx88 cards
The auto selection of pertinent helper chips (VIDEO_HELPER_CHIPS_AUTO)
should select the wm8775 driver, which is used by at least one
Conexant 2388x based card (Hauppauge HVR-1300), if VIDEO_CX88 is
selected.
V4L/DVB (6833): Don't limit cx88 audio routing to blackbird boards
All cx2388 boards need the line-in audio to be routed from an external ADC
(refered to as "ADC mode" in the spec sheet), since the chip is uncapable
of dealing with baseband audio directly.
So... this patch enables normal mode when using the tuner (TV or Radio), and
enables ADC mode with any other source. It'll probably only work with boards
that have supported ADCs (such as the Wolfson wm9775)
V4L/DVB (6831): Audio routes fix for blackbird boards with the wm8775 ADC
Fix lack of audio on the MPEG-2 stream of wm8775 based blackbirds.
The wm8775 module initializes the audio input at "route 2", which doesn't
hold true for all boards. The HVR-1300, for example, uses route 1 for
tuner audio, and route 2 for baseband. So we must route the audio to the
proper input depending on what video input is being used.
Remove the unnecessary BLACKBIRD_UNMUTE calls to the mpeg encoder in
cx88-blackbird.c
The encoder is never muted, hence unmuting should then only be necessary
once after hardware initialization.
I tested this from warm boots and cold boots (with long power down time
to ensure the sram in the chip is emptied), and found that after the
firmware upload the encoder is apparently not muted, making the unmutes
unnecessary.
This patch should fix the 'muted audio' and 'raspy audio' problem for
mpeg2 streams out of cx88-blackbird devices.
Especially mythtv users would find that the audio would often sound bad
(aliased, or 'raspy'), mainly related to channel changes, many (all?)
other users would find that there was no audio at all in the mpeg data
from the encoder chip, unless the audio was manually unmuted.
The patch includes the following modifications:
Don't actually start the mpeg2 encoder until the device is read from
by the application.
Wait until the audio is stable for at least 400ms before starting the
mpeg encoder.
Mute/Unmute the audio when starting/stopping the mpeg encoder.
Stop the mpeg encoder when changing parameters and when changing tuner
frequency.
Add a variable 'mpeg_active' to struct cx8802_dev to allow tracking of
whether or not the mpeg2 encoder is active.
drivers/media/video/et61x251/et61x251_core.c:390: warning: 'et61x251_i2c_read' defined but not used
drivers/media/video/et61x251/et61x251_core.c:397: warning: 'et61x251_i2c_write' defined but not used
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Mon, 10 Dec 2007 01:23:30 +0000 (22:23 -0300)]
V4L/DVB (6801): tda18271: pass i2c gate configuration into tda18271_attach()
If we pass TDA18271_GATE_DIGITAL into tda18271_attach(), it will always try to
use the digital demodulator's i2c gate.
If we pass TDA18271_GATE_ANALOG into tda18271_attach(), it will always try to
use the analog demodulator's i2c gate.
If we pass TDA18271_GATE_AUTO into tda18271_attach(), it will try to use the
analog demodulator's i2c gate when tuning in analog mode, and it will try to
use the digital demodulator's i2c gate when tuning in digital mode.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (6795): Add EXPORT_SYMBOL_GPL to the saa7134 video control routines
Those newer functions are used by saa7134-empress. Adds export for them:
+EXPORT_SYMBOL_GPL(saa7134_g_ctrl);
+EXPORT_SYMBOL_GPL(saa7134_s_ctrl);
+EXPORT_SYMBOL_GPL(saa7134_queryctrl);
Michael Krufky [Sun, 9 Dec 2007 05:26:48 +0000 (02:26 -0300)]
V4L/DVB (6785): tda8290: remove dependency on struct tuner
- remove dependency of tda8290 module on struct tuner
- move tuner_foo printk macros from tuner-driver.h into tuner-core.c
- clean up #includes of tuner-i2c.h / tuner-driver.h
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 driver tries to keep all device specific attributes in a
single data structure in one source file. This change further cleans
up how that table is set up. We now try to group everything together
for each specific device, and the number of symbols exported from this
module has now been reduced to a single global.
Signed-off-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (6755): Avoid troubles when using multiple devices
mv_count is a counter used to move the vertical bars. Before this patch, it
where a static var. This works fine for just one device. However, when using
multiple devices, every device would increment it.
This patch moves it to its correct place: struct vivi_dev. So, now, each device
has its own data.
V4L/DVB (6753): Fix vivi to support non-zero minor node
There were a trouble at vivi driver when using non-zero inodes. This where due
to not properly preserving the minor inode after calling video_register. Since
this driver is a reference for newer drivers, and it is possible to have more
than one video device inside the machine, this patch makes vivi to dynamically
allocate video_device struct.
Thanks to Gregor Jasny <jasny@vidsoft.de> for pointing the issue.
Also, this patch removes a very anoying (but useless) message of not having a
proper release call.
CC: Gregor Jasny <jasny@vidsoft.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Albert Graham [Sun, 9 Dec 2007 12:44:38 +0000 (09:44 -0300)]
V4L/DVB (6752): saa7134: Enable remote control support for Avermedia M102
This patch enabled the IR remote control for the Avermedia M102 (card=110),
which appears to be the same IR as the already supported device on the
Avermedia AVerTV GO 007 FM (card=57) model, the code is two one liners which
enable the IR for this device (subsystem: 1461:f31e)
Signed-off-by: Albert Graham <agraham@g-b.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
projects / linux-2.6 / log