Herbert Xu [Tue, 20 Jun 2006 06:57:59 +0000 (23:57 -0700)]
[NET]: Prevent multiple qdisc runs
Having two or more qdisc_run's contend against each other is bad because
it can induce packet reordering if the packets have to be requeued. It
appears that this is an unintended consequence of relinquinshing the queue
lock while transmitting. That in turn is needed for devices that spend a
lot of time in their transmit routine.
There are no advantages to be had as devices with queues are inherently
single-threaded (the loopback device is not but then it doesn't have a
queue).
Even if you were to add a queue to a parallel virtual device (e.g., bolt
a tbf filter in front of an ipip tunnel device), you would still want to
process the queue in sequence to ensure that the packets are ordered
correctly.
The solution here is to steal a bit from net_device to prevent this.
BTW, as qdisc_restart is no longer used by anyone as a module inside the
kernel (IIRC it used to with netif_wake_queue), I have not exported the
new __qdisc_run function.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 20 Jun 2006 02:07:12 +0000 (19:07 -0700)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (51 commits)
[MIPS] Make timer interrupt frequency configurable from kconfig.
[MIPS] Correct HAL2 Kconfig description
[MIPS] Fix R4K cache macro names
[MIPS] Add Missing R4K Cache Macros to IP27 & IP32
[MIPS] Support for the RM9000-based Basler eXcite smart camera platform.
[MIPS] Support for the R5500-based NEC EMMA2RH Mark-eins board
[MIPS] Support SNI RM200C SNI in big endian mode and R5000 processors.
[MIPS] SN: include asm/sn/types.h for nasid_t.
[MIPS] Random fixes for sb1250
[MIPS] Fix bcm1480 compile
[MIPS] Remove support for NEC DDB5476.
[MIPS] Remove support for NEC DDB5074.
[MIPS] Cleanup memory managment initialization.
[MIPS] SN: Declare bridge_pci_ops.
[MIPS] Remove unused function alloc_pci_controller.
[MIPS] IP27: Extract pci_ops into separate file.
[MIPS] IP27: Use symbolic constants instead of magic numbers.
[MIPS] vr41xx: remove unnecessay items from vr41xx/Kconfig.
[MIPS] IP27: Cleanup N/M mode configuration.
[MIPS] IP27: Throw away old unused hacks.
...
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (109 commits)
[ETHTOOL]: Fix UFO typo
[SCTP]: Fix persistent slowdown in sctp when a gap ack consumes rx buffer.
[SCTP]: Send only 1 window update SACK per message.
[SCTP]: Don't do CRC32C checksum over loopback.
[SCTP] Reset rtt_in_progress for the chunk when processing its sack.
[SCTP]: Reject sctp packets with broadcast addresses.
[SCTP]: Limit association max_retrans setting in setsockopt.
[PFKEYV2]: Fix inconsistent typing in struct sadb_x_kmprivate.
[IPV6]: Sum real space for RTAs.
[IRDA]: Use put_unaligned() in irlmp_do_discovery().
[BRIDGE]: Add support for NETIF_F_HW_CSUM devices
[NET]: Add NETIF_F_GEN_CSUM and NETIF_F_ALL_CSUM
[TG3]: Convert to non-LLTX
[TG3]: Remove unnecessary tx_lock
[TCP]: Add tcp_slow_start_after_idle sysctl.
[BNX2]: Update version and reldate
[BNX2]: Use CPU native page size
[BNX2]: Use compressed firmware
[BNX2]: Add firmware decompression
[BNX2]: Allow WoL settings on new 5708 chips
...
Manual fixup for conflict in drivers/net/tulip/winbond-840.c
Linus Torvalds [Tue, 20 Jun 2006 01:53:20 +0000 (18:53 -0700)]
Merge branch 'i915fb' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/intelfb-2.6
* 'i915fb' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/intelfb-2.6: (25 commits)
intelfb: fixup clock calculation debugging.
Removed hard coded EDID buffer size.
intelfb: use regular modedb table instead of VESA
intelfb: use firmware EDID for mode database
Revert "intelfb driver -- use the regular modedb table instead of the VESA"
intelfb: int option fix
sync modesetting code with X.org
intelfb: align with changes from my X driver.
intelfb driver -- use the regular modedb table instead of the VESA
Adds support for 256MB aperture on 945 chipsets to the intelfb driver
intelfb -- uses stride alignment of 64 on the 9xx chipsets.
intelfb: some cleanups for intelfbhw
intelfb: fixup pitch calculation like X does
intelfb: fixup p calculation
This patch makes a needlessly global struct static.
intelfb: add i945GM support
intelfb: fixup whitespace..
intelfb: add hw cursor support for i9xx
intelfb: make i915 modeset
intelfb: add support for i945G
...
Linus Torvalds [Tue, 20 Jun 2006 01:16:01 +0000 (18:16 -0700)]
Add support for suspending and resuming the whole console subsystem
Trying to suspend/resume with console messages flying all around is
doomed to failure, when the devices that the messages are trying to
go to are being shut down.
James Bottomley [Wed, 14 Jun 2006 02:31:19 +0000 (21:31 -0500)]
[SCSI] 53c700: remove reliance on deprecated cmnd fields
This one's quite tricky. The 53c700 uses the now deprecated fields of
the command structure for saving the prior command when it does
autosense. To fix this, we have to add extra fields to the LUN to
accommodate a copy of the real command.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Updates:
- don't bypass SYNCHRONIZE_CACHE command
- return SCSI_MLQUEUE_HOST_BUSY when no free request slots
- move scsi_remove_host() to the begin of hpt_remove(), or it will
not work after resources being released.
Signed-off-by: HighPoint Linux Team <linux@highpoint-tech.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Kenji Kaneshige [Fri, 12 May 2006 04:39:45 +0000 (13:39 +0900)]
[PATCH] pciehp: Implement get_address callback
This patch implements .get_address callback of hotplug_slot_ops for
PCIEHP driver. With this patch, we can see bus address of hotplug
slots as follows:
Kenji Kaneshige [Fri, 12 May 2006 02:22:24 +0000 (11:22 +0900)]
[PATCH] pciehp: Replace pci_find_slot() with pci_get_slot()
This patch replaces pci_find_slot() with pci_get_slot() in PCIEHP
driver. This patch enables PCI Express Hotplug on the system which has
multiple PCI domains.
Mike Habeck [Sat, 6 May 2006 14:01:59 +0000 (09:01 -0500)]
[PATCH] SGI Hotplug: Incorrect power status
This is a repost of a patch submitted by Prarit Bhargava on 01-19-06 that
never got integrated.
The get_power_status function is currently reporting a bitwise mapping of
the slot if the slot is powered on. It should return 1 if powered on and
0 if powered off.
Signed-off-by: Mike Habeck <habeck@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current SHPCHP driver doesn't take care of RsvdP/RsvdZ[*] bits in
controller SERR-INT register. This might cause unpredicable
results. This patch fixes this bug.
[*] RsvdP and RsvdZ are defined in SHPC spec as follows:
RsvdP - Reserved and Preserved. Register bits of this type are
reserved for future use as R/W bits. The value read is
undefined. Writes are ignored. Software must follow These rules
when accessing RsvdP bits:
- Software must ignore RsvdP bits when testing values read
from these registers.
- Software must not depend on RsvdP bit's ability to retain
information when written
- Software must always write back the value read in the RsvdP
bits when writing one of these registers.
RsvdZ - Reserved and Zero. Register bits of this type are reserved
for future use as R/WC bits. The value read is undefined. Writes
are ignored. Software must follow these rules when accessing RsvdZ
bits:
- Software must ignore RsvdZ bits when testing values read
from these registers.
- Software must not depends on a RsvdZ bit's ability to retain
information when written.
- Software must always write 0 to RsvdZ bits when writing one
of these register.
Current SHPCHP driver doesn't take care of RsvdP/RsvdZ[*] bits
in logical slot registers. This might cause unpredicable results. This
patch fixes this bug.
[*] RsvdP and RsvdZ are defined in SHPC spec as follows:
RsvdP - Reserved and Preserved. Register bits of this type are
reserved for future use as R/W bits. The value read is
undefined. Writes are ignored. Software must follow These rules
when accessing RsvdP bits:
- Software must ignore RsvdP bits when testing values read
from these registers.
- Software must not depend on RsvdP bit's ability to retain
information when written
- Software must always write back the value read in the RsvdP
bits when writing one of these registers.
RsvdZ - Reserved and Zero. Register bits of this type are reserved
for future use as R/WC bits. The value read is undefined. Writes
are ignored. Software must follow these rules when accessing RsvdZ
bits:
- Software must ignore RsvdZ bits when testing values read
from these registers.
- Software must not depends on a RsvdZ bit's ability to retain
information when written.
- Software must always write 0 to RsvdZ bits when writing one
of these register.
Current PCHEHP driver doesn't have any code to program hotplug
parameters from firmware. So hotplug parameters are never programed at
hot-add time. This patch add support for programming hotplug
parameters to PCIEHP driver.
Kenji Kaneshige [Wed, 10 May 2006 13:20:34 +0000 (22:20 +0900)]
[PATCH] acpi_pcihp: Remove improper error message about OSHP
This patch converts the improper error message about OSHP evaluation
to debug message which is displayed only when pci_hotplug.ko is loaded
with debugging mode enabled. To do this, this patch adds a new module
parameter "debug_acpi" to pci_hotplug.ko for enabling/disabling debug
messages in acpi_pcihp.c.
Kenji Kaneshige [Tue, 2 May 2006 01:54:50 +0000 (10:54 +0900)]
[PATCH] acpi_pcihp: Fix programming _HPP values
This patch fixes the problem that hotplug parameters are not programed
when PCI cards are hot-added by ACPIPHP, SHPCHP and PCIEHP driver. The
pci_dev structure being hot-added is not bound to ACPI handle, so we
need to trace PCI bus tree to find ACPI handle.
MUNEDA Takahiro [Wed, 22 Mar 2006 05:49:33 +0000 (14:49 +0900)]
[PATCH] acpiphp: turn off slot power at error case
When acpiphp_enable_slot() is failed, acpiphp does not change
the slot->flags. Therefore, when user tries to read power
status, acpiphp_get_power_status() returns the enable status
whether the slot is not really enabled.
MUNEDA Takahiro [Wed, 22 Mar 2006 05:49:27 +0000 (14:49 +0900)]
[PATCH] acpiphp: host and p2p hotplug
I encountered the problem that when there are some hotplug
slots are under the host bridge, the hotplug slots under the
p2p bridge are not treated as hotpluggable.
MUNEDA Takahiro [Wed, 22 Mar 2006 05:49:20 +0000 (14:49 +0900)]
[PATCH] acpiphp: hotplug slot hotplug
o hotplug slots add
When the hot-added PCI device is p2p bridge, acpiphp calls
find_p2p_bridge() to add hotplug slots.
o hotplug slots remove
When the hot-removing PCI device is p2p bridge, acpiphp
calls cleanup_p2p_bridge() to remove hotplug slots.
o notify handler exchange
When the p2p bridge is added, acpiphp changes the notify
hanlder.
If no bridge device is inserted into the hotpluggable PCI
slot, acpiphp installs the notify handler for function.
After the p2p bridge hot-add, acpiphp has to install the
notify handler for bridge. Because, the role of the
handlers are not same. The hot-remove case is ditto.
MUNEDA Takahiro [Wed, 22 Mar 2006 05:49:09 +0000 (14:49 +0900)]
[PATCH] acpiphp: configure _PRT - V3
Current acpiphp does not free acpi_device structs when the
PCI devices are removed. When the PCI device is added,
acpi_bus_add() fails because acpi_device struct has already
exists. So, _PRT method does not evaluate.
Richard Purdie [Mon, 19 Jun 2006 19:46:05 +0000 (20:46 +0100)]
[ARM] 3594/1: Poodle: Add touchscreen support + other updates
Patch from Richard Purdie
Poodle Updates:
* Update corgi_ssp to make the GPIO chip selects optional
* Enable corgi_ssp for use by poodle
* Add corgi touchscreen platform device for poodle
* Export locomo platform device.
* Set framebuffer device parent correctly
Signed-off-by: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Andrew Victor [Mon, 19 Jun 2006 18:53:19 +0000 (19:53 +0100)]
[ARM] 3592/1: AT91RM9200 Serial driver update
Patch from Andrew Victor
This patch includes a number of updates to the AT91RM9200 serial driver.
Changes include:
1. Conversion to a platform_driver. [Ivan Kokshaysky]
2. Replaced all references to AT91RM9200 with AT91. This driver can now
also be used for the AT91SAM9216.
3. Allow TIOCM_LOOP to configure local loopback mode.
4. Cleaned up the 'read_status_mask' usage and interrupt handler code.
[Chip Coldwell]
5. Suspend/resume support. [David Brownell]
There are a few 'unused variable' warning when compiling this - I
removed the new DMA support to keep this first patch simpler.
Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Andrew Victor [Mon, 19 Jun 2006 17:16:45 +0000 (18:16 +0100)]
[ARM] 3589/1: AT91RM9200 DK/EK board update
Patch from Andrew Victor
This patch updates the support for the Atmel DK and EK boards.
The changes include:
1. Use the new at91_uart_config structure and device registration
functions for the UARTs.
2. Registration of I2C and SPI platform devices.
3. The USB Device pullup line is connected to reset, so multidrive needs
to be enabled on the line. [Patch from David Brownell].
Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Atsushi Nemoto [Mon, 19 Jun 2006 15:19:13 +0000 (00:19 +0900)]
[MIPS] Make timer interrupt frequency configurable from kconfig.
Make HZ configurable. DECSTATION can select 128/256/1024 HZ, JAZZ can
only select 100 HZ, others can select 100/128/250/256/1000/1024 HZ if
not explicitly specified). Also remove all mach-xxx/param.h files and
update all defconfigs according to current HZ value.
Kumba [Sun, 18 Jun 2006 06:17:08 +0000 (02:17 -0400)]
[MIPS] Correct HAL2 Kconfig description
The current HAL2 Kconfig description indicates it is only used on SGI
Indy systems, however all members of the Indigo2 Family have this sound
card as well. Plus a minor grammatical fix is included.
Kumba [Sun, 18 Jun 2006 06:16:53 +0000 (02:16 -0400)]
[MIPS] Add Missing R4K Cache Macros to IP27 & IP32
Keeping in accordance with other machines, IP27 and IP32 lack a few
macros. IP27 lacks cpu_has_4kex & cpu_has_4k_cache macros while IP32
lacks just the cpu_has_4k_cache macro.
Ralf Baechle [Sun, 18 Jun 2006 00:32:22 +0000 (01:32 +0100)]
[MIPS] Cleanup memory managment initialization.
Historically plat_mem_setup did the entire platform initialization. This
was rather impractical because it meant plat_mem_setup had to get away
without any kind of memory allocator. To keep old code from breaking
plat_setup was just renamed to plat_setup and a second platform
initialization hook for anything else was introduced.
Ralf Baechle [Mon, 12 Jun 2006 11:20:09 +0000 (12:20 +0100)]
[MIPS] Drop 0 definition for kern_addr_valid
kern_addr_valid is currently only being used in kmem_ptr_validate which
is making some vague attempt at verfying the validity of an address.
Only IA-64, PARISC and x86-64 actually make some actual effort to verify
the validity of the pointer. Most architecture definitions of
kern_addr_valid() just define it as 1; the Alpha and CONFIG_DISCONTIGMEM
on i386 and MIPS even as 0; the 0-definition will result in
kmem_ptr_validate always failing which in turn will cause d_validate to
always fail. d_validate's only two users are smbfs and ncpfs, so the
0 definition ended breaking those ...
Ralf Baechle [Sun, 11 Jun 2006 22:03:08 +0000 (23:03 +0100)]
[MIPS] Cleanup ARCH_DISCONTIGMEM_ENABLE and NUMA configuration.
IP27 configuration isn't the only NUMA system - it just happens to be
the currently only supported MIPS NUMA system. So move the necessary
options back into the main MIPS Kconfig file.
Sergei Shtylyov [Sat, 27 May 2006 20:04:01 +0000 (00:04 +0400)]
[MIPS] arch/mips/au1000/time.c cleanup
Mark au1xxx_timer_setup() __init, just because it is. Get rid of
unneeded extern's (note that (*do_gettimeoffset)() is already declared by
<asm/time.c>) and an unused variable. Kill some whitespace...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto [Mon, 15 May 2006 16:26:03 +0000 (01:26 +0900)]
[MIPS] Unify mips_fpu_soft_struct and mips_fpu_hard_structs.
The struct mips_fpu_soft_struct and mips_fpu_hard_struct are
completely same now and the kernel fpu emulator assumes that. This
patch unifies them to mips_fpu_struct and get rid of mips_fpu_union.
projects / linux-2.6 / log