* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh64-2.6:
sh64: Flag sh64_get_page() as __init_refok.
sh64: Move entry point code to .text.head.
sh64: Fix up PCI section mismatch warnings.
sh64: Update cayman defconfig.
sh64: Wire up fallocate() syscall.
Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: (29 commits)
libata: implement EH fast drain
libata: schedule probing after SError access failure during autopsy
libata: clear HOTPLUG flag after a reset
libata: reorganize ata_ehi_hotplugged()
libata: improve SCSI scan failure handling
libata: quickly trigger SATA SPD down after debouncing failed
libata: improve SATA PHY speed down logic
The SATA controller device ID is different according to
ahci: implement SCR_NOTIFICATION r/w
ahci: make NO_NCQ handling more consistent
libata: make ->scr_read/write callbacks return error code
libata: implement AC_ERR_NCQ
libata: improve EH report formatting
sata_sil24: separate out sil24_do_softreset()
sata_sil24: separate out sil24_exec_polled_cmd()
sata_sil24: replace sil24_update_tf() with sil24_read_tf()
ahci: separate out ahci_do_softreset()
ahci: separate out ahci_exec_polled_cmd()
ahci: separate out ahci_kick_engine()
ahci: use deadline instead of fixed timeout for 1st FIS for SRST
...
Dan Williams [Fri, 20 Jul 2007 07:31:46 +0000 (00:31 -0700)]
async_tx: fix kmap_atomic usage in async_memcpy
Andrew Morton:
[async_memcpy] is very wrong if both ASYNC_TX_KMAP_DST and
ASYNC_TX_KMAP_SRC can ever be set. We'll end up using the same kmap
slot for both src add dest and we get either corrupted data or a BUG.
Evgeniy Polyakov:
Btw, shouldn't it always be kmap_atomic() even if flag is not set.
That pages are usual one returned by alloc_page().
So fix the usage of kmap_atomic and kill the ASYNC_TX_KMAP_DST and
ASYNC_TX_KMAP_SRC flags.
Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nick Piggin [Fri, 20 Jul 2007 07:31:45 +0000 (00:31 -0700)]
fix some conversion overflows
Fix page index to offset conversion overflows in buffer layer, ecryptfs,
and ocfs2.
It would be nice to convert the whole tree to page_offset, but for now
just fix the bugs.
Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Michael Halcrow <mhalcrow@us.ibm.com> Cc: Mark Fasheh <mark.fasheh@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Mundt [Fri, 20 Jul 2007 07:31:44 +0000 (00:31 -0700)]
mm: fix memory hotplug oops from ZONE_MOVABLE changes.
zone_movable_pfn is presently marked as __initdata and referenced from
adjust_zone_range_for_zone_movable(), which in turn is referenced by
zone_spanned_pages_in_node(). Both of these are __meminit annotated. When
memory hotplug is enabled, this will oops on a hot-add, due to
zone_movable_pfn having been freed.
__meminitdata annotation gives the desired behaviour.
This will only impact platforms that enable both memory hotplug
and ARCH_POPULATES_NODE_MAP.
Signed-off-by: Paul Mundt <lethal@linux-sh.org> Acked-by: Mel Gorman <mel@csn.ul.ie> Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Roland McGrath [Fri, 20 Jul 2007 07:31:43 +0000 (00:31 -0700)]
xen: disable vdso "nosegneg" on native boot
One of the nice ideas behind paravirt is that CONFIG_XEN=y can be included
in a standard configuration and be no worse for native booting than as a
Xen guest. The glibc feature that supports the vDSO "nosegneg" note is
designed specifically to make this easy. You just have to flip one bit at
boot time. This patch makes Xen flip the bit, so a CONFIG_XEN=y kernel on
bare hardware does not make glibc use the less-optimized library builds.
Signed-off-by: Roland McGrath <roland@redhat.com> Acked-by: Jeremy Fitzhardinge <jeremy@xensource.com> Cc: Andi Kleen <ak@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Fix two year old bug in early bootup asm.
[SPARC64]: Update defconfig.
[SPARC64]: Fix log message type in vio_create_one().
[SPARC64]: Tweak assertions in sun4v_build_virq().
[SPARC64]: Tweak kernel log messages in power_probe().
[SPARC64]: Fix handling of multiple vdc-port nodes.
[SPARC64]: Fix device type matching in VIO's devspec_show().
[SPARC64]: Fix MODULE_DEVICE_TABLE() specification in VDC and VNET.
[SPARC]: Add sys_fallocate() entries.
[SPARC64]: Use orderly_poweroff().
Al Viro [Fri, 20 Jul 2007 15:07:33 +0000 (16:07 +0100)]
Fix up sky2 breakage
Doing |= 1 << 19 to 16bit unsigned is not particulary useful;
that register is 32bit, unlike the ones dealt with in the rest of
function, so we need u32 variable here.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Acked-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In most cases, when EH is scheduled, all in-flight commands are
aborted causing EH to kick in immediately. However, in some cases
(especially with PMP), it's unclear which commands are affected by the
error condition and although aborting all in-flight commands work, it
isn't optimal and may cause unnecessary disruption. On the other
hand, waiting for in-flight commands to drain themselves can take up
to 30seconds.
This patch implements EH fast drain to handle such situations. It
gives in-flight commands some time to finish up but doesn't wait for
too long. After EH is scheduled, fast drain timer is started and if
no other completion occurs in ATA_EH_FASTDRAIN_INTERVAL all in-flight
commands are aborted. If any completion occurred in the interval, the
port is given another interval to finish up itself.
Currently ATA_EH_FASTDRAIN_INTERVAL is 3 secs which should be enough
for finishing up most commands.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata: schedule probing after SError access failure during autopsy
If SError isn't accessible, EH can't tell whether hotplug has happened
or not. Report SError read failure with AC_ERR_OTHER and schedule
probing with hardreset. This will be mainly useful for PMPs.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA_EHI_HOTPLUGGED is a hint for reset functions indicating the the
port might have gone through hotplug/unplug just before entering EH.
Reset functions modify their behaviors a bit to handle the situation
better - e.g. using longer debouncing delay.
Currently, once HOTPLUG is set, it isn't cleared till the end of EH.
This is unnecessary and makes EH take longer. Clear the HOTPLUGGED
flag after a reset try (successful or not).
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
__ata_ehi_hotplugged() now has no users. Regorganize
ata_ehi_hotplugged() such that a new function ata_ehi_schedule_probe()
deals with scheduling probing. ata_ehi_hotplugged() calls it and
additionally marks hotplug specific flags. ata_ehi_schedule_probe()
will be used laster.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
SCSI scan may fail due to memory allocation failure even if EH is not
in progress. Due to use of GFP_ATOMIC in SCSI scan path, allocation
failure isn't too rare especially while probing multiple devices at
once which is the case when a bunch of devices are connected to PMP.
This patch moves SCSI scan failure detetion logic from
ata_scsi_hotplug() to ata_scsi_scan_host() and implement synchronous
scan behavior. The synchronous path sleeps briefly and repeats SCSI
scan if some devices aren't attached properly. It contains robust
retry loop to minimize the chance of device misdetection during boot
and falls back to async retry if everything fails.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata: quickly trigger SATA SPD down after debouncing failed
Debouncing failure is a good indicator of basic link problem. Use
-EPIPE to indicate debouncing failure and make ata_eh_reset() invoke
sata_down_spd_limit() if the error occurs during reset.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
sata_down_spd_limit() first reads the current SPD from SStatus and
limit the speed to the lower one of one below the current limit or one
below the current SPD in SStatus. SPD may not be accessible or valid
when SPD down is requested making sata_down_spd_limit() fail when it's
most needed.
This patch makes the current SPD cached after each successful reset
and forces GEN I speed (1.5Gbps) if neither of SStatus or the cached
value is valid, so sata_down_spd_limit() is now guaranteed to lower
the speed limit if lower speed is available.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
su henry [Fri, 20 Jul 2007 12:07:46 +0000 (08:07 -0400)]
The SATA controller device ID is different according to
the onchip SATA type set in the system BIOS:
Device Device ID
SATA in IDE mode 0x4390
SATA in AHCI mode 0x4391
SATA in non-raid5 driver 0x4392
SATA in raid5 driver 0x4393
Although the device ID is different, they use the same AHCI driver
.The attached file is the patch for adding these device
IDs for ATI SB700.
Signed-off-by: henry.su.ati@gmail.com Signed-off-by: Jeff Garzik <jeff@garzik.org>
ahci_save_initial_config() is responsible for reading, screening the
host CAP register and storing the modified result into hpriv->cap for
the rest of the driver. Move ATA_FLAG_NO_NCQ handling into
ahci_save_initial_config(). It's more consistent this way and the
rest of the driver can always refer to hpriv->cap to determine
configured capability.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
When an NCQ command fails, all commands in flight are aborted and the
offending one is reported using log page 10h. Depending on controller
characteristics and LLD implementation, all commands may appear as
having a device error due to shared TF status making it hard to
determine what's actually going on.
This patch adds AC_ERR_NCQ, marks the command reported by log page 10h
with it and print extra "<F>" after the error report for the command
to help distinguishing the offending command.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Requiring LLDs to format multiple error description messages properly
doesn't work too well. Help LLDs a bit by making ata_ehi_push_desc()
insert ", " on each invocation. __ata_ehi_push_desc() is the raw
version without the automatic separator.
While at it, make ehi_desc interface proper functions instead of
macros.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
sata_sil24: replace sil24_update_tf() with sil24_read_tf()
Replace sil24_update_tf() to sil24_read_tf() which reads TF into
passed int result TF argument and can read TFs of PMP links. This
will be used by PMP support.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out ahci_exec_polled_cmd() from ahci_softreset(). This will
be used to implement ahci_pmp_read/write(). ahci_exec_polled_cmd()
performs reset_engine before returning if the command fails (times
out). This is to improve robustness.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out stop_engine - CLO - start_engine sequence from
ahci_softreset() and ahci_clo() into ahci_reset_engine() and use it in
ahci_softreset() and ahci_post_internal_cmd(). The function will also
be used to prepare for and clean up after PMP register access
commands.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add @is_cmd to ata_tf_to_fis(). This controls bit 7 of the second
byte which tells the device whether this H2D FIS is for a command or
not. This cleans up ahci a bit and will be used by PMP.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Petr Vandrovec [Fri, 20 Jul 2007 11:44:44 +0000 (07:44 -0400)]
[libata] Fix reported task file values in sense data
ata_tf_read was setting HOB bit when lba48 command was submitted, but
was not clearing it before reading "normal" data. As it is only place
which sets HOB bit in control register, and register reads should not
be affected by other bits, let's just clear it when we are done with
reading upper bytes so non-48bit commands do not have to touch ctl
at all.
pata_scc suffered from same problem...
Signed-off-by: Petr Vandrovec <petr@vandrovec.name> Signed-off-by: Jeff Garzik <jeff@garzik.org>
pata_scc.c: small fixes (Workaround for errata A308)
This patch fixes some issues of the previous patch:
- Use mode_filter() hook to limit ATAPI UDMA mode
- "data loss" warning message
- handling of udma_mask
Magnus Damm [Fri, 20 Jul 2007 03:50:58 +0000 (12:50 +0900)]
pata_platform: Fix NULL pointer dereference
pata_platform: Fix NULL pointer dereference
pata_platform currently dereferences a NULL pointer in pata_platform_probe()
if pdev->dev.platform_data is set to NULL. This breakage was most likely
introduced by commit 5f45bc50976ee1f408f7171af155aec646655a37.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jeff Garzik [Fri, 13 Jul 2007 21:06:45 +0000 (17:06 -0400)]
[libata] sata_mv: minor cleanups
* trim trailing whitespace
* document some flags, registers, and register bits
* fix locking around EDMA on/off and configuration
* continue replacing "constant OP var" with "var OP constant"
* use new pci_try_set_mwi()
Paul Mundt [Fri, 20 Jul 2007 08:46:42 +0000 (17:46 +0900)]
sh64: Flag sh64_get_page() as __init_refok.
sh64_get_page() wraps in to regular allocators as well as the
bootmem allocator for fetching pages, it carefully checks to
see which one it can use depending on the system state, so
the access is safe.
There are some leftover bits from the task cooperator patch, that was
yanked out again. While it will get reintroduced, no point in having
this write-only stuff in the tree. So yank it.
If we have two processes with different ioprio_class, but the same
ioprio_data, their async requests will fall into the same queue. I guess
such behavior is not expected, because it's not right to put real-time
requests and best-effort requests in the same queue.
The attached patch fixes the problem by introducing additional *cfqq
fields on cfqd, pointing to per-(class,priority) async queues.
David S. Miller [Fri, 20 Jul 2007 04:50:09 +0000 (21:50 -0700)]
[SPARC64]: Fix two year old bug in early bootup asm.
We try to fetch the CIF entry pointer from %o4, but that
can get clobbered by the early OBP calls. It is saved
in %l7 already, so actually this "mov %o4, %l7" can just
be completely removed with no other changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 18 Jul 2007 22:15:45 +0000 (15:15 -0700)]
[SPARC64]: Fix handling of multiple vdc-port nodes.
The "id" property in vdc-port nodes are not unique, they
are all zero. Therefore assign ID's using the parent's
"cfg-handle" property which will be unique.
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Mundt [Fri, 20 Jul 2007 01:11:58 +0000 (10:11 +0900)]
mm: Remove slab destructors from kmem_cache_create().
Slab destructors were no longer supported after Christoph's c59def9f222d44bb7e2f0a559f2906191a0862d7 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Alan Stern [Wed, 18 Jul 2007 16:14:24 +0000 (12:14 -0400)]
USB: change name of spinlock in hcd.c
This patch (as940 renames hcd_data_lock in hcd.c to hcd_urb_list_lock,
which is more descriptive of the lock's job. It also introduces a
convenient inline routine for testing whether a particular USB device
is a root hub.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Wed, 18 Jul 2007 16:08:02 +0000 (12:08 -0400)]
USB: move routines in hcd.c
This patch (as939) moves a couple of routine in hcd.c around. The
purpose is to put all the general URB- and endpoint-related routines
(submit, unlink, giveback, and disable) together in one spot.
There are no functional changes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / linux-2.6 / log