Pierre Ossman [Sat, 5 Jul 2008 23:10:27 +0000 (01:10 +0200)]
mmc: remove multiwrite capability
Relax requirements on host controllers and only require that they do not
report a transfer count than is larger than the actual one (i.e. a lower
value is okay). This is how many other parts of the kernel behaves so
upper layers should already be prepared to handle that scenario. This
gives us a performance boost on MMC cards.
atmel-mci: Driver for Atmel on-chip MMC controllers
This is a driver for the MMC controller on the AP7000 chips from
Atmel. It should in theory work on AT91 systems too with some
tweaking, but since the DMA interface is quite different, it's not
entirely clear if it's worth merging this with the at91_mci driver.
This driver has been around for a while in BSPs and kernel sources
provided by Atmel, but this particular version uses the generic DMA
Engine framework (with the slave extensions) instead of an
avr32-only DMA controller framework.
This driver can also use PIO transfers when no DMA channels are
available, and for transfers where using DMA may be difficult or
impractical for some reason (e.g. the DMA setup overhead is usually
not worth it for very short transfers, and badly aligned buffers or
lengths are difficult to handle.)
Currently, the driver only support PIO transfers. DMA support has been
split out to a separate patch to hopefully make it easier to review.
The driver has been tested using mmc-block and ext3fs on several SD,
SDHC and MMC+ cards. Reads and writes work fine, with read transfer
rates up to 3.5 MiB/s on fast cards with debugging disabled.
The driver has also been tested using the mmc_test module on the same
cards. All tests except 7, 9, 15 and 17 succeed. The first two are
unsupported by all the cards I have, so I don't know if the driver
handles this correctly. The last two fail because the hardware flags a
Data CRC Error instead of a Data Timeout error. I'm not sure how to deal
with that.
Documentation for this controller can be found in many data sheets from
Atmel, including the AT32AP7000 data sheet which can be found here:
Tomas Winkler [Mon, 30 Jun 2008 07:50:24 +0000 (10:50 +0300)]
mmc: fix sdio_io sparse errors
This patch fixes sdio_io sparse errors.
This fix changes signature of API functions,
changing
unsigned char -> u8
unsigned short -> u16
unsigned long -> u32 - this was probably a bug in 64 bit platforms
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The hardware does not support any multi-block transfers
with an block-size that is not 32bit aligned. Also the driver
itself does not support single block non-32bit transfers
either.
Ensure that the s3cmci_setup_data() returns the appropriate
error if we encounter this.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Ben Dooks [Mon, 30 Jun 2008 21:40:36 +0000 (22:40 +0100)]
MMC: S3C24XX: Add media presence test to request handling.
Ensure that we have physical media present before attempting to
send a request to a card. This ensures that we do not get flooded
by errors from commands that can never be completed timing out.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The driver should be checking for a negative error code from
s3c2410_dma_request(), not non-zero. Newer kernels now return
the DMA channel number that was allocated by the request.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Ben Dooks [Mon, 30 Jun 2008 21:40:29 +0000 (22:40 +0100)]
MMC: S3C24XX: Add platform data for MMC/SD driver
This patch adds platform data support to the s3mci driver. This allows
flexible board-specific configuration of set_power, card detect and read only
pins.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Pierre Ossman [Sun, 29 Jun 2008 10:19:47 +0000 (12:19 +0200)]
mmc_block: wait for card even on failures
Many failures are non-permanent, but the card might need some time to
finish what it is doing before becoming responsive again. Make sure we
wait for it to finish programming before dealing with the error.
Pierre Ossman [Sat, 28 Jun 2008 16:28:51 +0000 (18:28 +0200)]
sdhci: scatter-gather (ADMA) support
Add support for the scatter-gather DMA mode present on newer controllers.
As the mode requires 32-bit alignment, non-aligned chunks are handled by
using a bounce buffer.
Also add some new quirks to handle controllers that have bugs in the
ADMA engine.
Pierre Ossman [Sat, 28 Jun 2008 11:22:40 +0000 (13:22 +0200)]
sdio: clean up handling of byte mode transfer size
Make sure that the maximum size for a byte mode transfer is identical
in all places. Also tweak the transfer helper so that a single byte
mode transfer is preferred over (possibly multiple) block mode
request(s).
Pierre Ossman [Sat, 28 Jun 2008 10:52:45 +0000 (12:52 +0200)]
mmc,sdio: helper function for transfer padding
There are a lot of crappy controllers out there that cannot handle
all the request sizes that the MMC/SD/SDIO specifications require.
In case the card driver can pad the data to overcome the problems,
this commit adds a helper that calculates how much that padding
should be.
A corresponding helper is also added for SDIO, but it can also deal
with all the complexities of splitting up a large transfer efficiently.
Manuel Lauss [Mon, 9 Jun 2008 06:36:13 +0000 (08:36 +0200)]
au1xmmc: remove db1200 board code, rewrite probe.
Remove the DB1200 board-specific functions (card present, read-only,
activity LED methods) and instead add platform data which is passed
to the driver. This also allows for platforms to implement other
carddetect schemes (e.g. dedicated irq) without having to pollute the
driver code. The poll timer (used for pb1200) is kept for compatibility.
With the board-specific stuff gone, the driver's ->probe() code can be
cleaned up considerably.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Ville Syrjala [Mon, 9 Jun 2008 19:06:45 +0000 (22:06 +0300)]
at91_mci: Fix byte mode transitions.
The byte mode support fails to clear the byte mode bit in the command
register, possibly leaving byte mode enabled with the counters programmed
in non-byte mode.
Signed-off-by: Ville Syrjala <syrjala@sci.fi> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Ville Syrjala [Mon, 9 Jun 2008 19:06:44 +0000 (22:06 +0300)]
at91_mci: Cover more AT91RM9200 and AT91SAM9261 errata.
According to the documentation the AT91SAM9261 MCI shares the block size
limitations of the AT91RM9200 MCI. Also the errata documentation for
AT91RM9200 and AT91SAM9261 state that stream commands are not supported.
This has not been tested on actual hardware.
Signed-off-by: Ville Syrjala <syrjala@sci.fi> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
AT91SAM926[0/3] PDC must write at least 12 bytes. The code compiles and runs
but the actual condition for this erratum did not trigger in my tests so it's
unclear if it actually works as intended.
Signed-off-by: Ville Syrjala <syrjala@sci.fi> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Marc Pignat [Fri, 30 May 2008 12:07:47 +0000 (14:07 +0200)]
mmc: at91_mci: avoid timeouts
The at91 mci controller internal state machine seems to often crash. This can
be fixed by resetting the controller after each command for at91rm9200 and by
setting the MCI_BLKR register on at91sam926*.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch> Signed-off-by: Hans J Koch <hjk@linutronix.de> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Marc Pignat [Fri, 30 May 2008 12:06:32 +0000 (14:06 +0200)]
mmc: at91_mci: show timeouts
Detect command timeout (or mci controller hangs).
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch> Signed-off-by: Hans J Koch <hjk@linutronix.de> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Marc Pignat [Fri, 30 May 2008 12:05:24 +0000 (14:05 +0200)]
mmc: at91_mci: support for block size not modulo 4
Implement transfer with size not modulo 4 for at91sam9*. Please note that the
at91rm9200 simply can't handle this.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Anton Vorontsov [Tue, 17 Jun 2008 14:17:39 +0000 (18:17 +0400)]
mmc: change .get_ro() callback semantics
Now get_ro() callback must return 0/1 values for its logical states, and
negative errno values in case of error. If particular host instance doesn't
support RO/WP switch, it should return -ENOSYS.
This patch changes some hosts in two ways:
1. Now functions should be smart to not return negative values in
"RO asserted" case (particularly gpio_ calls could return negative
values for the outermost GPIOs).
Also, board code usually passes get_ro() callbacks that directly return
gpioreg & bit result, so at91_mci, imxmmc, pxamci and mmc_spi's get_ro()
handlers need take special care when returning platform's values to the
mmc core.
2. In case of host instance didn't implement get_ro() callback, it should
really return -ENOSYS and let the mmc core decide what to do about it
(mmc core thinks the same way as the hosts, so it isn't functional
change).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Anton Vorontsov [Tue, 17 Jun 2008 14:17:21 +0000 (18:17 +0400)]
mmc_spi: add support for card-detection polling
This patch adds new platform data variable "caps", so platforms
could pass theirs capabilities into MMC core (for example, platforms
without interrupt on the CD line will most probably want to pass
MMC_CAP_NEEDS_POLL).
New platform get_cd() callback provided to optimize polling.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Anton Vorontsov [Tue, 17 Jun 2008 14:17:15 +0000 (18:17 +0400)]
mmc: add support for card-detection polling
Some hosts (and boards that use mmc_spi) do not use interrupts on the CD
line, so they can't trigger mmc_detect_change. We want to poll the card
and see if there was a change. 1 second poll interval seems resonable.
This patch also implements .get_cd() host operation, that could be used
by the hosts that are able to report card-detect status without need to
talk MMC.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Pierre Ossman [Fri, 4 Jul 2008 22:25:15 +0000 (00:25 +0200)]
sdhci: make workaround for timeout bug more general
Give the quirk for broken timeout handling a better chance of handling
more controllers by simply classifying the system as broken and setting
a fixed value.
Pierre Ossman [Sat, 22 Mar 2008 21:05:40 +0000 (22:05 +0100)]
sdhci: remove forced dma quirks
Remove the quirk to force DMA on the Ricoh and TI controllers as it is
no longer needed. The only bug they have is that they use an incorrect
PCI interface value, and that is not respected anymore.
Pierre Ossman [Tue, 18 Mar 2008 16:35:49 +0000 (17:35 +0100)]
sdhci: move pci stuff to separate module
The SDHCI interface is not PCI specific, yet the Linux driver was
intimitely connected to the PCI bus. This patch properly separates
the PCI specific portion from the bus independent code.
This patch is based on work by Ben Dooks but he did not have time
to complete it.
Pierre Ossman [Fri, 18 Apr 2008 18:41:49 +0000 (20:41 +0200)]
sdhci: don't check block count for progress
The specification is insufficiently strict when it comes to how the
hardware should update the block count register, making it useless
for checking transfer progress.
David Woodhouse [Tue, 15 Jul 2008 00:50:24 +0000 (17:50 -0700)]
firmware: Correct dependency on CONFIG_EXTRA_FIRMWARE_DIR
When CONFIG_EXTRA_FIRMWARE_DIR gets changed, the filename in the .S file
(which uses .incbin to include the binary) needs to change. When we
renamed the BUILTIN_FIRMWARE_DIR option to EXTRA_FIRMWARE_DIR, we forgot
to update the manual dependency in firmware/Makefile, so it was
depending on a non-existent file in include/config/
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'for-2.6.27' of git://git.infradead.org/users/dwmw2/firmware-2.6
* 'for-2.6.27' of git://git.infradead.org/users/dwmw2/firmware-2.6: (64 commits)
firmware: convert sb16_csp driver to use firmware loader exclusively
dsp56k: use request_firmware
edgeport-ti: use request_firmware()
edgeport: use request_firmware()
vicam: use request_firmware()
dabusb: use request_firmware()
cpia2: use request_firmware()
ip2: use request_firmware()
firmware: convert Ambassador ATM driver to request_firmware()
whiteheat: use request_firmware()
ti_usb_3410_5052: use request_firmware()
emi62: use request_firmware()
emi26: use request_firmware()
keyspan_pda: use request_firmware()
keyspan: use request_firmware()
ttusb-budget: use request_firmware()
kaweth: use request_firmware()
smctr: use request_firmware()
firmware: convert ymfpci driver to use firmware loader exclusively
firmware: convert maestro3 driver to use firmware loader exclusively
...
Fix up trivial conflicts with BKL removal in drivers/char/dsp56k.c and
drivers/char/ip2/ip2main.c manually.
Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (241 commits)
[ARM] 5171/1: ep93xx: fix compilation of modules using clocks
[ARM] 5133/2: at91sam9g20 defconfig file
[ARM] 5130/4: Support for the at91sam9g20
[ARM] 5160/1: IOP3XX: gpio/gpiolib support
[ARM] at91: Fix NAND FLASH timings for at91sam9x evaluation kits.
[ARM] 5084/1: zylonite: Register AC97 device
[ARM] 5085/2: PXA: Move AC97 over to the new central device declaration model
[ARM] 5120/1: pxa: correct platform driver names for PXA25x and PXA27x UDC drivers
[ARM] 5147/1: pxaficp_ir: drop pxa_gpio_mode calls, as pin setting
[ARM] 5145/1: PXA2xx: provide api to control IrDA pins state
[ARM] 5144/1: pxaficp_ir: cleanup includes
[ARM] pxa: remove pxa_set_cken()
[ARM] pxa: allow clk aliases
[ARM] Feroceon: don't disable BPU on boot
[ARM] Orion: LED support for HP mv2120
[ARM] Orion: add RD88F5181L-FXO support
[ARM] Orion: add RD88F5181L-GE support
[ARM] Orion: add Netgear WNR854T support
[ARM] s3c2410_defconfig: update for current build
[ARM] Acer n30: Minor style and indentation fixes.
...
Merge branch 'core/softirq' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core/softirq' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
softirq: remove irqs_disabled warning from local_bh_enable
softirq: remove initialization of static per-cpu variable
Remove argument from open_softirq which is always NULL
Merge branch 'core/printk' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core/printk' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, generic: mark early_printk as asmlinkage
printk: export console_drivers
printk: remember the message level for multi-line output
printk: refactor processing of line severity tokens
printk: don't prefer unsuited consoles on registration
printk: clean up recursion check related static variables
namespacecheck: more kernel/printk.c fixes
namespacecheck: fix kernel printk.c
Merge branch 'core/locking' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core/locking' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
lockdep: fix kernel/fork.c warning
lockdep: fix ftrace irq tracing false positive
lockdep: remove duplicate definition of STATIC_LOCKDEP_MAP_INIT
lockdep: add lock_class information to lock_chain and output it
lockdep: add lock_class information to lock_chain and output it
lockdep: output lock_class key instead of address for forward dependency output
__mutex_lock_common: use signal_pending_state()
mutex-debug: check mutex magic before owner
Merge branch 'sched/new-API-sched_setscheduler' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched/new-API-sched_setscheduler' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: add new API sched_setscheduler_nocheck: add a flag to control access checks
Merge branch 'tracing/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (228 commits)
ftrace: build fix for ftraced_suspend
ftrace: separate out the function enabled variable
ftrace: add ftrace_kill_atomic
ftrace: use current CPU for function startup
ftrace: start wakeup tracing after setting function tracer
ftrace: check proper config for preempt type
ftrace: trace schedule
ftrace: define function trace nop
ftrace: move sched_switch enable after markers
ftrace: prevent ftrace modifications while being kprobe'd, v2
fix "ftrace: store mcount address in rec->ip"
mmiotrace broken in linux-next (8-bit writes only)
ftrace: avoid modifying kprobe'd records
ftrace: freeze kprobe'd records
kprobes: enable clean usage of get_kprobe
ftrace: store mcount address in rec->ip
ftrace: build fix with gcc 4.3
namespacecheck: fixes
ftrace: fix "notrace" filtering priority
ftrace: fix printout
...
Jaswinder Singh [Fri, 27 Jun 2008 14:20:40 +0000 (19:50 +0530)]
vicam: use request_firmware()
Although it wasn't actually using ihex records before, we use the Intel
HEX record format for this firmware -- because that gives us a simple
way to split it into separate chunks internally as we need, without
loading each part as a separate file.
Signed-off-by: Jaswinder Singh <jaswinder@infradead.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Merge branch 'sched/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (76 commits)
sched_clock: and multiplier for TSC to gtod drift
sched_clock: record TSC after gtod
sched_clock: only update deltas with local reads.
sched_clock: fix calculation of other CPU
sched_clock: stop maximum check on NO HZ
sched_clock: widen the max and min time
sched_clock: record from last tick
sched: fix accounting in task delay accounting & migration
sched: add avg-overlap support to RT tasks
sched: terminate newidle balancing once at least one task has moved over
sched: fix warning
sched: build fix
sched: sched_clock_cpu() based cpu_clock(), lockdep fix
sched: export cpu_clock
sched: make sched_{rt,fair}.c ifdefs more readable
sched: bias effective_load() error towards failing wake_affine().
sched: incremental effective_load()
sched: correct wakeup weight calculations
sched: fix mult overflow
sched: update shares on wakeup
...
* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6: (31 commits)
avr32: Fix typo of IFSR in a comment in the PIO header file
avr32: Power Management support ("standby" and "mem" modes)
avr32: Add system device for the internal interrupt controller (intc)
avr32: Add simple SRAM allocator
avr32: Enable SDRAMC clock at startup
rtc-at32ap700x: Enable wakeup
macb: Basic suspend/resume support
atmel_serial: Drain console TX shifter before suspending
atmel_serial: Fix build on avr32 with CONFIG_PM enabled
avr32: Use a quicklist for PTE allocation as well
avr32: Use a quicklist for PGD allocation
avr32: Cover the kernel page tables in the user PGDs
avr32: Store virtual addresses in the PGD
avr32: Remove useless zeroing of swapper_pg_dir at startup
avr32: Clean up and optimize the TLB operations
avr32: Rename at32ap.c -> pdc.c
avr32: Move setup_platform() into chip-specific file
avr32: Kill special exception handler sections
avr32: Kill unneeded #include <asm/pgalloc.h> from asm/mmu_context.h
avr32: Clean up time.c #includes
...
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (25 commits)
security: remove register_security hook
security: remove dummy module fix
security: remove dummy module
security: remove unused sb_get_mnt_opts hook
LSM/SELinux: show LSM mount options in /proc/mounts
SELinux: allow fstype unknown to policy to use xattrs if present
security: fix return of void-valued expressions
SELinux: use do_each_thread as a proper do/while block
SELinux: remove unused and shadowed addrlen variable
SELinux: more user friendly unknown handling printk
selinux: change handling of invalid classes (Was: Re: 2.6.26-rc5-mm1 selinux whine)
SELinux: drop load_mutex in security_load_policy
SELinux: fix off by 1 reference of class_to_string in context_struct_compute_av
SELinux: open code sidtab lock
SELinux: open code load_mutex
SELinux: open code policy_rwlock
selinux: fix endianness bug in network node address handling
selinux: simplify ioctl checking
SELinux: enable processes with mac_admin to get the raw inode contexts
Security: split proc ptrace checking into read vs. attach
...
Merge branch 'for-linus' of git://git.alsa-project.org/alsa-kernel
* 'for-linus' of git://git.alsa-project.org/alsa-kernel: (179 commits)
ALSA: Release v1.0.17
ALSA: correct kcalloc usage
ALSA: ALSA driver for SGI O2 audio board
ALSA: asoc: kbuild - only show menus for the current ASoC CPU platform.
ALSA: ALSA driver for SGI HAL2 audio device
ALSA: hda - Fix FSC V5505 model
ALSA: hda - Fix missing init for unsol events on micsense model
ALSA: hda - Fix internal mic vref pin setup
ALSA: hda: 92hd71bxx PC Beep
ALSA: HDA - HP dc7600 with pci sub IDs 0x103c/0x3011 belongs to hp-3013 model
ALSA: usb-audio: add some Yamaha USB MIDI quirks
ALSA: usb-audio: fix Yamaha KX quirk
ALSA: ASoC: Au12x0/Au1550 PSC Audio support
ALSA: Add Yamaha KX49 (USB MIDI controller) to usbquirks.h
ALSA: ASoC: pxa2xx-ac97: fix warning due to missing argument in fuction declaration
ALSA: tosa: fix compilation with new DAPM API
ALSA: wavefront - add const
ALSA: remove CONFIG_KMOD from sound
ALSA: Fix a const to non-const assignment in the Digigram VXpocket sound driver
ALSA: Fix a const pointer usage warning in the Digigram VX soundcard driver
...
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block: (37 commits)
splice: fix generic_file_splice_read() race with page invalidation
ramfs: enable splice write
drivers/block/pktcdvd.c: avoid useless memset
cdrom: revert commit 22a9189 (cdrom: use kmalloced buffers instead of buffers on stack)
scsi: sr avoids useless buffer allocation
block: blk_rq_map_kern uses the bounce buffers for stack buffers
block: add blk_queue_update_dma_pad
DAC960: push down BKL
pktcdvd: push BKL down into driver
paride: push ioctl down into driver
block: use get_unaligned_* helpers
block: extend queue_flag bitops
block: request_module(): use format string
Add bvec_merge_data to handle stacked devices and ->merge_bvec()
block: integrity flags can't use bit ops on unsigned short
cmdfilter: extend default read filter
sg: fix odd style (extra parenthesis) introduced by cmd filter patch
block: add bounce support to blk_rq_map_user_iov
cfq-iosched: get rid of enable_idle being unused warning
allow userspace to modify scsi command filter on per device basis
...
projects / linux-2.6 / log