Adrian Bunk [Mon, 3 Mar 2008 18:07:42 +0000 (20:07 +0200)]
sh/mm/pg-sh7705.c must #include <linux/fs.h>
This patch fixes the following compile error:
<-- snip -->
...
CC arch/sh/mm/pg-sh7705.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/mm/pg-sh7705.c: In function 'ptep_get_and_clear':
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/mm/pg-sh7705.c:130: error: implicit declaration of function 'mapping_writably_mapped'
make[2]: *** [arch/sh/mm/pg-sh7705.o] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <adrian.bunk@movial.fi> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Pavel Roskin [Thu, 28 Feb 2008 22:11:02 +0000 (17:11 -0500)]
module: allow ndiswrapper to use GPL-only symbols
A change after 2.6.24 broke ndiswrapper by accidentally removing its
access to GPL-only symbols. Revert that change and add comments about
the reasons why ndiswrapper and driverloader are treated in a special
way.
Signed-off-by: Pavel Roskin <proski@gnu.org> Acked-by: Greg KH <gregkh@suse.de> Acked-by: Ingo Molnar <mingo@elte.hu> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Jon Masters <jonathan@jonmasters.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (22 commits)
[IPCONFIG]: The kernel gets no IP from some DHCP servers
b43legacy: Fix module init message
rndis_wlan: fix broken data copy
libertas: compare the current command with response
libertas: fix sanity check on sequence number in command response
p54: fix eeprom parser length sanity checks
p54: fix EEPROM structure endianness
ssb: Add pcibios_enable_device() return value check
rc80211-pid: fix rate adjustment
[ESP]: Add select on AUTHENC
[TCP]: Improve ipv4 established hash function.
[NETPOLL]: Revert two bogus cleanups that broke netconsole.
[PPPOL2TP]: Add missing sock_put() in pppol2tp_tunnel_closeall()
Subject: [PPPOL2TP] add missing sock_put() in pppol2tp_recv_dequeue()
[BLUETOOTH]: l2cap info_timer delete fix in hci_conn_del
[NET]: Fix race in generic address resolution.
iucv: fix build error on !SMP
[TCP]: Must count fack_count also when skipping
[TUN]: Fix RTNL-locking in tun/tap driver
[SCTP]: Use proc_create to setup de->proc_fops.
...
[IPCONFIG]: The kernel gets no IP from some DHCP servers
From: Stephen Hemminger <shemminger@linux-foundation.org>
Based upon a patch by Marcel Wappler:
This patch fixes a DHCP issue of the kernel: some DHCP servers
(i.e. in the Linksys WRT54Gv5) are very strict about the contents
of the DHCPDISCOVER packet they receive from clients.
Table 5 in RFC2131 page 36 requests the fields 'ciaddr' and
'siaddr' MUST be set to '0'. These DHCP servers ignore Linux
kernel's DHCP discovery packets with these two fields set to
'255.255.255.255' (in contrast to popular DHCP clients, such as
'dhclient' or 'udhcpc'). This leads to a not booting system.
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 5 Mar 2008 00:39:23 +0000 (16:39 -0800)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] fix ia64 kprobes compilation
[IA64] move gcc_intrin.h from header-y to unifdef-y
[IA64] workaround tiger ia64_sal_get_physical_id_info hang
[IA64] move defconfig to arch/ia64/configs/
[IA64] Fix irq migration in multiple vector domain
[IA64] signal(ia64_ia32): add a signal stack overflow check
[IA64] signal(ia64): add a signal stack overflow check
[IA64] CONFIG_SGI_SN2 - auto select NUMA and ACPI_NUMA
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6:
debugfs: fix sparse warnings
Driver core: Fix cleanup when failing device_add().
driver core: Remove dpm_sysfs_remove() from error path of device_add()
PM: fix new mutex-locking bug in the PM core
PM: Do not acquire device semaphores upfront during suspend
kobject: properly initialize ksets
sysfs: CONFIG_SYSFS_DEPRECATED fix
driver core: fix up Kconfig text for CONFIG_SYSFS_DEPRECATED
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: ftdi_sio - really enable EM1010PC
USB: remove incorrect struct class_device from the printer gadget
USB: pxa2xx_udc: fix misuse of clock enable/disable calls
USB: ftdi_sio: Workaround for broken Matrix Orbital serial port
USB: Add support for AXESSTEL MV110H CDMA modem
usb-storage: update earlier scatter-gather bug fix
USB: isp116x: fix enumeration on boot
USB: ehci: handle large bulk URBs correctly (again)
USB: spruce up the device blacklist
USB: fix comment of struct usb_interface
USB: update Kconfig entry for USB_SUSPEND
usb: Add support for the mos7820/7840-based B&B USB/RS485 converter to mos7840.c
Randy Dunlap [Tue, 4 Mar 2008 22:29:43 +0000 (14:29 -0800)]
input: add I2C to config since the driver makes several i2c*() calls
Add to help text that the Intel I2C ICH (i801) driver is also needed
for this kernel.
Add LEDS_CLASS to config since the driver makes les_classdev_*() calls:
ERROR: "led_classdev_register" [drivers/input/misc/apanel.ko] undefined!
ERROR: "__led_classdev_unregister" [drivers/input/misc/apanel.ko]
undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Josef Bacik [Tue, 4 Mar 2008 22:29:43 +0000 (14:29 -0800)]
ext3: fix mount option parsing
The "resize" option won't be noticed as it comes after the NULL option, so if
you try to mount (or in this case remount) with that option it won't be
recognized.
Signed-off-by: Josef Bacik <jbacik@redhat.com> Cc: <linux-ext4@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
hugetlb: fix pool shrinking while in restricted cpuset
Adam Litke noticed that currently we grow the hugepage pool independent of any
cpuset the running process may be in, but when shrinking the pool, the cpuset
is checked. This leads to inconsistency when shrinking the pool in a
restricted cpuset -- an administrator may have been able to grow the pool on a
node restricted by a containing cpuset, but they cannot shrink it there.
There are two options: either prevent growing of the pool outside of the
cpuset or allow shrinking outside of the cpuset. >From previous discussions
on linux-mm, /proc/sys/vm/nr_hugepages is an administrative interface that
should not be restricted by cpusets. So allow shrinking the pool by removing
pages from nodes outside of current's cpuset.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com> Acked-by: Adam Litke <agl@us.ibm.com> Cc: William Irwin <wli@holomorphy.com> Cc: Lee Schermerhorn <Lee.Schermerhonr@hp.com> Cc: Christoph Lameter <clameter@sgi.com> Cc: Paul Jackson <pj@sgi.com> Cc: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adam Litke [Tue, 4 Mar 2008 22:29:38 +0000 (14:29 -0800)]
hugetlb: close a difficult to trigger reservation race
A hugetlb reservation may be inadequately backed in the event of racing
allocations and frees when utilizing surplus huge pages. Consider the
following series of events in processes A and B:
A) Allocates some surplus pages to satisfy a reservation
B) Frees some huge pages
A) A notices the extra free pages and drops hugetlb_lock to free some of
its surplus pages back to the buddy allocator.
B) Allocates some huge pages
A) Reacquires hugetlb_lock and returns from gather_surplus_huge_pages()
Avoid this by commiting the reservation after pages have been allocated but
before dropping the lock to free excess pages. For parity, release the
reservation in return_unused_surplus_pages().
This patch also corrects the cpuset_mems_nr() error path in
hugetlb_acct_memory(). If the cpuset check fails, uncommit the
reservation, but also be sure to return any surplus huge pages that may
have been allocated to back the failed reservation.
Thanks to Andy Whitcroft for discovering this.
Signed-off-by: Adam Litke <agl@us.ibm.com> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Andy Whitcroft <apw@shadowen.org> Cc: Dave Hansen <haveblue@us.ibm.com> Cc: William Lee Irwin III <wli@holomorphy.com> Cc: Andy Whitcroft <apw@shadowen.org> Cc: Mel Gorman <mel@csn.ul.ie> Cc: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
K.Tanaka [Tue, 4 Mar 2008 22:29:37 +0000 (14:29 -0800)]
md: the md RAID10 resync thread could cause a md RAID10 array deadlock
This message describes another issue about md RAID10 found by testing the
2.6.24 md RAID10 using new scsi fault injection framework.
Abstract:
When a scsi error results in disabling a disk during RAID10 recovery, the
resync threads of md RAID10 could stall.
This case, the raid array has already been broken and it may not matter. But
I think stall is not preferable. If it occurs, even shutdown or reboot will
fail because of resource busy.
The deadlock mechanism:
The r10bio_s structure has a "remaining" member to keep track of BIOs yet to
be handled when recovering. The "remaining" counter is incremented when
building a BIO in sync_request() and is decremented when finish a BIO in
end_sync_write().
If building a BIO fails for some reasons in sync_request(), the "remaining"
should be decremented if it has already been incremented. I found a case
where this decrement is forgotten. This causes a md_do_sync() deadlock
because md_do_sync() waits for md_done_sync() called by end_sync_write(), but
end_sync_write() never calls md_done_sync() because of the "remaining" counter
mismatch.
For example, this problem would be reproduced in the following case:
The resync thread keeps working, but actually it is deadlocked.
Patch:
By this patch, the remaining counter will be decremented if needed.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NeilBrown [Tue, 4 Mar 2008 22:29:35 +0000 (14:29 -0800)]
md: fix possible raid1/raid10 deadlock on read error during resync
Thanks to K.Tanaka and the scsi fault injection framework, here is a fix for
another possible deadlock in raid1/raid10 error handing.
If a read request returns an error while a resync is happening and a resync
request is pending, the attempt to fix the error will block until the resync
progresses, and the resync will block until the read request completes. Thus
a deadlock.
This patch fixes the problem.
Cc: "K.Tanaka" <k-tanaka@ce.jp.nec.com> Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Keld Simonsen [Tue, 4 Mar 2008 22:29:34 +0000 (14:29 -0800)]
md: don't attempt read-balancing for raid10 'far' layouts
This patch changes the disk to be read for layout "far > 1" to always be the
disk with the lowest block address.
Thus the chunks to be read will always be (for a fully functioning array) from
the first band of stripes, and the raid will then work as a raid0 consisting
of the first band of stripes.
Some advantages:
The fastest part which is the outer sectors of the disks involved will be
used. The outer blocks of a disk may be as much as 100 % faster than the
inner blocks.
Average seek time will be smaller, as seeks will always be confined to the
first part of the disks.
Mixed disks with different performance characteristics will work better, as
they will work as raid0, the sequential read rate will be number of disks
involved times the IO rate of the slowest disk.
If a disk is malfunctioning, the first disk which is working, and has the
lowest block address for the logical block will be used.
Signed-off-by: Keld Simonsen <keld@dkuug.dk> Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NeilBrown [Tue, 4 Mar 2008 22:29:33 +0000 (14:29 -0800)]
md: lock access to rdev attributes properly
When we access attributes of an rdev (component device on an md array) through
sysfs, we really need to lock the array against concurrent changes. We
currently do that when we change an attribute, but not when we read an
attribute. We need to lock when reading as well else rdev->mddev could become
NULL while we are accessing it.
So add appropriate locking (mddev_lock) to rdev_attr_show.
rdev_size_store requires some extra care as well as it needs to unlock the
mddev while scanning other mddevs for overlapping regions. We currently
assume that rdev->mddev will still be unchanged after the scan, but that
cannot be certain. So take a copy of rdev->mddev for use at the end of the
function.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NeilBrown [Tue, 4 Mar 2008 22:29:32 +0000 (14:29 -0800)]
md: make sure a reshape is started when device switches to read-write
A resync/reshape/recovery thread will refuse to progress when the array is
marked read-only. So whenever it mark it not read-only, it is important to
wake up thread resync thread. There is one place we didn't do this.
The problem manifests if the start_ro module parameters is set, and a raid5
array that is in the middle of a reshape (restripe) is started. The array
will initially be semi-read-only (meaning it acts like it is readonly until
the first write). So the reshape will not proceed.
On the first write, the array will become read-write, but the reshape will not
be started, and there is no event which will ever restart that thread.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NeilBrown [Tue, 4 Mar 2008 22:29:31 +0000 (14:29 -0800)]
md: clean up irregularity with raid autodetect
When a raid1 array is stopped, all components currently get added to the list
for auto-detection. However we should really only add components that were
found by autodetection in the first place. So add a flag to record that
information, and use it.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NeilBrown [Tue, 4 Mar 2008 22:29:31 +0000 (14:29 -0800)]
md: guard against possible bad array geometry in v1 metadata
Make sure the data doesn't start before the end of the superblock when the
superblock is at the start of the device.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NeilBrown [Tue, 4 Mar 2008 22:29:30 +0000 (14:29 -0800)]
md: reduce CPU wastage on idle md array with a write-intent bitmap
On an md array with a write-intent bitmap, a thread wakes up every few seconds
and scans the bitmap looking for work to do. If the array is idle, there will
be no work to do, but a lot of scanning is done to discover this.
So cache the fact that the bitmap is completely clean, and avoid scanning the
whole bitmap when the cache is known to be clean.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NeilBrown [Tue, 4 Mar 2008 22:29:29 +0000 (14:29 -0800)]
md: fix deadlock in md/raid1 and md/raid10 when handling a read error
When handling a read error, we freeze the array to stop any other IO while
attempting to over-write with correct data.
This is done in the raid1d(raid10d) thread and must wait for all submitted IO
to complete (except for requests that failed and are sitting in the retry
queue - these are counted in ->nr_queue and will stay there during a freeze).
However write requests need attention from raid1d as bitmap updates might be
required. This can cause a deadlock as raid1 is waiting for requests to
finish that themselves need attention from raid1d.
So we create a new function 'flush_pending_writes' to give that attention, and
call it in freeze_array to be sure that we aren't waiting on raid1d.
Thanks to "K.Tanaka" <k-tanaka@ce.jp.nec.com> for finding and reporting this
problem.
Cc: "K.Tanaka" <k-tanaka@ce.jp.nec.com> Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
FUJITA Tomonori [Tue, 4 Mar 2008 22:29:28 +0000 (14:29 -0800)]
iommu: parisc: pass struct device to iommu_alloc_range
This adds struct device argument to sba_alloc_range and ccio_alloc_range, a
preparation for modifications to fix the IOMMU segment boundary problem. This
change enables ccio_alloc_range to access to LLD's segment boundary limits.
[akpm@linux-foundation.org: coding-style fixes] Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Cc: Kyle McMartin <kyle@parisc-linux.org> Cc: Matthew Wilcox <matthew@wil.cx> Cc: Grant Grundler <grundler@parisc-linux.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
FUJITA Tomonori [Tue, 4 Mar 2008 22:29:27 +0000 (14:29 -0800)]
iommu: export iommu_is_span_boundary helper function
iommu_is_span_boundary is used internally in the IOMMU helper
(lib/iommu-helper.c), a primitive function that judges whether a memory area
spans LLD's segment boundary or not.
It's difficult to convert some IOMMUs to use the IOMMU helper but
iommu_is_span_boundary is still useful for them. So this patch exports it.
This is needed for the parisc iommu fixes.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Cc: Kyle McMartin <kyle@parisc-linux.org> Cc: Matthew Wilcox <matthew@wil.cx> Cc: Grant Grundler <grundler@parisc-linux.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kyle McMartin [Tue, 4 Mar 2008 22:29:26 +0000 (14:29 -0800)]
hisax_fcpcipnp: move request_irq later in probe
After a quick glance at the code, we're getting the DEBUG_SHIRQ spurious
interrupt before we have the adapter template filled in. Real interrupts
appear to be turned on by fcpci*_init(), so move request_irq until just before
that.
Michael Halcrow [Tue, 4 Mar 2008 22:29:24 +0000 (14:29 -0800)]
eCryptfs: make ecryptfs_prepare_write decrypt the page
When the page is not up to date, ecryptfs_prepare_write() should be
acting much like ecryptfs_readpage(). This includes the painfully
obvious step of actually decrypting the page contents read from the
lower encrypted file.
Note that this patch resolves a bug in eCryptfs in 2.6.24 that one can
produce with these steps:
Jesper Nilsson [Tue, 4 Mar 2008 22:29:23 +0000 (14:29 -0800)]
cris: correct syscall numbers in unistd.h for timerfd_settime and timerfd_gettime
Last commit for unistd was not correct, it only had a partial update of
syscall numbers for __NR_timerfd_settime and __NR_timerfd_gettime. Also,
NR_syscalls was not incremented for the new syscalls.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com> Cc: Mikael Starvik <mikael.starvik@axis.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jesper Nilsson [Tue, 4 Mar 2008 22:29:23 +0000 (14:29 -0800)]
cris: correct usage of __user for copy to and from user space in lib/usercopy and uaccess.h
Function __copy_user_zeroing in arch/lib/usercopy.c had the wrong parameter
set as __user, and in include/asm-cris/uaccess.h, it was not set at all for
some of the calling functions.
This will cut the number of warnings quite dramatically when using sparse.
While we're here, remove useless CVS log and correct confusing typo.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com> Cc: Mikael Starvik <mikael.starvik@axis.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Julia Lawall [Tue, 4 Mar 2008 22:29:20 +0000 (14:29 -0800)]
fs/reiserfs/super.c: correct use of ! and &
In commit e6bafba5b4765a5a252f1b8d31cbf6d2459da337 ("wmi: (!x & y)
strikes again"), a bug was fixed that involved converting !x & y to !(x
& y). The code below shows the same pattern, and thus should perhaps be
fixed in the same way.
This is not tested and clearly changes the semantics, so it is only
something to consider.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
Signed-off-by: Julia Lawall <julia@diku.dk> Cc: Chris Mason <chris.mason@oracle.com> Cc: Jeff Mahoney <jeffm@suse.com> Cc: Jan Kara <jack@ucw.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Julia Lawall [Tue, 4 Mar 2008 22:29:19 +0000 (14:29 -0800)]
drivers/serial/m32r_sio.c: correct use of ! and &
In commit e6bafba5b4765a5a252f1b8d31cbf6d2459da337 ("wmi: (!x & y)
strikes again"), a bug was fixed that involved converting !x & y to !(x
& y). The code below shows the same pattern, and thus should perhaps be
fixed in the same way.
This is not tested and clearly changes the semantics, so it is only
something to consider.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
Julia Lawall [Tue, 4 Mar 2008 22:29:18 +0000 (14:29 -0800)]
drivers/isdn: correct use of ! and &
In commit e6bafba5b4765a5a252f1b8d31cbf6d2459da337 ("wmi: (!x & y)
strikes again"), a bug was fixed that involved converting !x & y to !(x
& y). The code below shows the same pattern, and thus should perhaps be
fixed in the same way.
This is not tested and clearly changes the semantics, so it is only
something to consider.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
Julia Lawall [Tue, 4 Mar 2008 22:29:17 +0000 (14:29 -0800)]
drivers/char/isicom.c: correct use of ! and &
In commit e6bafba5b4765a5a252f1b8d31cbf6d2459da337 ("wmi: (!x & y)
strikes again"), a bug was fixed that involved converting !x & y to !(x
& y). The code below shows the same pattern, and thus should perhaps be
fixed in the same way.
This is not tested and clearly changes the semantics, so it is only
something to consider.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
Hugh Dickins [Tue, 4 Mar 2008 22:29:16 +0000 (14:29 -0800)]
memcg: fix oops on NULL lru list
While testing force_empty, during an exit_mmap, __mem_cgroup_remove_list
called from mem_cgroup_uncharge_page oopsed on a NULL pointer in the lru list.
I couldn't see what racing tasks on other cpus were doing, but surmise that
another must have been in mem_cgroup_charge_common on the same page, between
its unlock_page_cgroup and spin_lock_irqsave near done (thanks to that kzalloc
which I'd almost changed to a kmalloc).
Normally such a race cannot happen, the ref_cnt prevents it, the final
uncharge cannot race with the initial charge. But force_empty buggers the
ref_cnt, that's what it's all about; and thereafter forced pages are
vulnerable to races such as this (just think of a shared page also mapped into
an mm of another mem_cgroup than that just emptied). And remain vulnerable
until they're freed indefinitely later.
This patch just fixes the oops by moving the unlock_page_cgroups down below
adding to and removing from the list (only possible given the previous patch);
and while we're at it, we might as well make it an invariant that
page->page_cgroup is always set while pc is on lru.
But this behaviour of force_empty seems highly unsatisfactory to me: why have
a ref_cnt if we always have to cope with it being violated (as in the earlier
page migration patch). We may prefer force_empty to move pages to an orphan
mem_cgroup (could be the root, but better not), from which other cgroups could
recover them; we might need to reverse the locking again; but no time now for
such concerns.
As for force_empty, though this may not be the main topic here,
mem_cgroup_force_empty_list() can be implemented simpler. It is possible to
make the function just call mem_cgroup_uncharge_page() instead of releasing
page_cgroups by itself. The tip is to call get_page() before invoking
mem_cgroup_uncharge_page(), so the page won't be released during this
function.
Kamezawa-san points out that by the time mem_cgroup_uncharge_page() uncharges,
the page might have been reassigned to an lru of a different mem_cgroup, and
now be emptied from that; but Hugh claims that's okay, the end state is the
same as when it hasn't gone to another list.
And once force_empty stops taking lock_page_cgroup within mz->lru_lock,
mem_cgroup_move_lists() can be simplified to take mz->lru_lock directly while
holding page_cgroup lock (but still has to use try_lock_page_cgroup).
Hugh Dickins [Tue, 4 Mar 2008 22:29:13 +0000 (14:29 -0800)]
memcg: fix mem_cgroup_move_lists locking
Ever since the VM_BUG_ON(page_get_page_cgroup(page)) (now Bad page state) went
into page freeing, I've hit it from time to time in testing on some machines,
sometimes only after many days. Recently found a machine which could usually
produce it within a few hours, which got me there at last.
The culprit is mem_cgroup_move_lists, whose locking is inadequate; and the
arrangement of structures was such that you got page_cgroups from the lru list
neatly put on to SLUB's freelist. Kamezawa-san identified the same hole
independently.
The main problem was that it was missing the lock_page_cgroup it needs to
safely page_get_page_cgroup; but it's tricky to go beyond that too, and I
couldn't do it with SLAB_DESTROY_BY_RCU as I'd expected. See the code for
comments on the constraints.
This patch immediately gets replaced by a simpler one from Hirokazu-san; but
is it just foolish pride that tells me to put this one on record, in case we
need to come back to it later?
Hugh Dickins [Tue, 4 Mar 2008 22:29:12 +0000 (14:29 -0800)]
memcg: css_put after remove_list
mem_cgroup_uncharge_page does css_put on the mem_cgroup before uncharging from
it, and before removing page_cgroup from one of its lru lists: isn't there a
danger that struct mem_cgroup memory could be freed and reused before
completing that, so corrupting something? Never seen it, and for all I know
there may be other constraints which make it impossible; but let's be
defensive and reverse the ordering there.
mem_cgroup_force_empty_list is safe because there's an extra css_get around
all its works; but even so, change its ordering the same way round, to help
get in the habit of doing it like this.
Hugh Dickins [Tue, 4 Mar 2008 22:29:11 +0000 (14:29 -0800)]
memcg: remove clear_page_cgroup and atomics
Remove clear_page_cgroup: it's an unhelpful helper, see for example how
mem_cgroup_uncharge_page had to unlock_page_cgroup just in order to call it
(serious races from that? I'm not sure).
Once that's gone, you can see it's pointless for page_cgroup's ref_cnt to be
atomic: it's always manipulated under lock_page_cgroup, except where
force_empty unilaterally reset it to 0 (and how does uncharge's
atomic_dec_and_test protect against that?).
Simplify this page_cgroup locking: if you've got the lock and the pc is
attached, then the ref_cnt must be positive: VM_BUG_ONs to check that, and to
check that pc->page matches page (we're on the way to finding why sometimes it
doesn't, but this patch doesn't fix that).
Hugh Dickins [Tue, 4 Mar 2008 22:29:10 +0000 (14:29 -0800)]
memcg: memcontrol uninlined and static
More cleanup to memcontrol.c, this time changing some of the code generated.
Let the compiler decide what to inline (except for page_cgroup_locked which is
only used when CONFIG_DEBUG_VM): the __always_inline on lock_page_cgroup etc.
was quite a waste since bit_spin_lock etc. are inlines in a header file; made
mem_cgroup_force_empty and mem_cgroup_write_strategy static.
Hugh Dickins [Tue, 4 Mar 2008 22:29:09 +0000 (14:29 -0800)]
memcg: memcontrol whitespace cleanups
Sorry, before getting down to more important changes, I'd like to do some
cleanup in memcontrol.c. This patch doesn't change the code generated, but
cleans up whitespace, moves up a double declaration, removes an unused enum,
removes void returns, removes misleading comments, that kind of thing.
Hugh Dickins [Tue, 4 Mar 2008 22:29:08 +0000 (14:29 -0800)]
memcg: remove mem_cgroup_uncharge
Nothing uses mem_cgroup_uncharge apart from mem_cgroup_uncharge_page, (a
trivial wrapper around it) and mem_cgroup_end_migration (which does the same
as mem_cgroup_uncharge_page). And it often ends up having to lock just to let
its caller unlock. Remove it (but leave the silly locking until a later
patch).
Moved mem_cgroup_cache_charge next to mem_cgroup_charge in memcontrol.h.
Hugh Dickins [Tue, 4 Mar 2008 22:29:08 +0000 (14:29 -0800)]
memcg: mem_cgroup_charge never NULL
My memcgroup patch to fix hang with shmem/tmpfs added NULL page handling to
mem_cgroup_charge_common. It seemed convenient at the time, but hard to
justify now: there's a perfectly appropriate swappage to charge and uncharge
instead, this is not on any hot path through shmem_getpage, and no performance
hit was observed from the slight extra overhead.
So revert that NULL page handling from mem_cgroup_charge_common; and make it
clearer by bringing page_cgroup_assign_new_page_cgroup into its body - that
was a helper I found more of a hindrance to understanding.
Hugh Dickins [Tue, 4 Mar 2008 22:29:07 +0000 (14:29 -0800)]
memcg: bad page if page_cgroup when free
Replace free_hot_cold_page's VM_BUG_ON(page_get_page_cgroup(page)) by a "Bad
page state" and clear: most users don't have CONFIG_DEBUG_VM on, and if it
were set here, it'd likely cause corruption when the page is reused.
Don't use page_assign_page_cgroup to clear it: that should be private to
memcontrol.c, and always called with the lock taken; and memmap_init_zone
doesn't need it either - like page->mapping and other pointers throughout the
kernel, Linux assumes pointers in zeroed structures are NULL pointers.
Instead use page_reset_bad_cgroup, added to memcontrol.h for this only.
Hugh Dickins [Tue, 4 Mar 2008 22:29:06 +0000 (14:29 -0800)]
memcg: fix VM_BUG_ON from page migration
Page migration gave me free_hot_cold_page's VM_BUG_ON page->page_cgroup.
remove_migration_pte was calling mem_cgroup_charge on the new page whenever it
found a swap pte, before it had determined it to be a migration entry. That
left a surplus reference count on the page_cgroup, so it was still attached
when the page was later freed.
Move that mem_cgroup_charge down to where we're sure it's a migration entry.
We were already under i_mmap_lock or anon_vma->lock, so its GFP_KERNEL was
already inappropriate: change that to GFP_ATOMIC.
It's essential that remove_migration_pte removes all the migration entries,
other crashes follow if not. So proceed even when the charge fails: normally
it cannot, but after a mem_cgroup_force_empty it might - comment in the code.
Hugh Dickins [Tue, 4 Mar 2008 22:29:04 +0000 (14:29 -0800)]
memcg: when do_swap's do_wp_page fails
Don't uncharge when do_swap_page's call to do_wp_page fails: the page which
was charged for is there in the pagetable, and will be correctly uncharged
when that area is unmapped - it was only its COWing which failed.
And while we're here, remove earlier XXX comment: yes, OR in do_wp_page's
return value (maybe VM_FAULT_WRITE) with do_swap_page's there; but if it
fails, mask out success bits, which might confuse some arches e.g. sparc.
Hugh Dickins [Tue, 4 Mar 2008 22:29:04 +0000 (14:29 -0800)]
memcg: page_cache_release not __free_page
There's nothing wrong with mem_cgroup_charge failure in do_wp_page and
do_anonymous page using __free_page, but it does look odd when nearby code
uses page_cache_release: use that instead (while turning a blind eye to
ancient inconsistencies of page_cache_release versus put_page).
Hugh Dickins [Tue, 4 Mar 2008 22:29:03 +0000 (14:29 -0800)]
memcg: move_lists on page not page_cgroup
Each caller of mem_cgroup_move_lists is having to use page_get_page_cgroup:
it's more convenient if it acts upon the page itself not the page_cgroup; and
in a later patch this becomes important to handle within memcontrol.c.
FUJITA Tomonori [Tue, 4 Mar 2008 22:28:57 +0000 (14:28 -0800)]
alpha: make IOMMU respect the segment boundary limits
This patch makes the IOMMU code not allocate a memory area spanning LLD's
segment boundary.
is_span_boundary() judges whether a memory area spans LLD's segment boundary.
If iommu_arena_find_pages() finds such a area, it tries to find the next
available memory area.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
FUJITA Tomonori [Tue, 4 Mar 2008 22:28:57 +0000 (14:28 -0800)]
alpha: IOMMU had better access to the free space bitmap at only one place
iommu_arena_find_pages duplicates the code to access to the bitmap for free
space management. This patch convert the IOMMU code to have only one place to
access the bitmap, in the popular way that other IOMMUs (e.g. POWER and
SPARC) do.
This patch is preparation for modifications to fix the IOMMU segment boundary
problem.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jesper Nilsson [Tue, 4 Mar 2008 22:28:52 +0000 (14:28 -0800)]
CRIS: Import string.c (memcpy) from newlib: fixes compile error with gcc 4
Adrian Bunk reported another compile error with a SVN head GCC:
...
CC arch/cris/arch-v10/lib/string.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/cris/arch-v10/lib/string.c:138:
error: lvalue required as increment operand
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/cris/arch-v10/lib/string.c:138:
error: lvalue required as increment operand
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/cris/arch-v10/lib/string.c:139:
error: lvalue required as increment operand
...
This is due to the use of the construct:
*((long*)dst)++ = lc;
Which isn't legal since casts don't return an lvalue.
The solution is to import the implementation from newlib,
which is continually autotested together with GCC mainline,
and uses the construct:
*(long *) dst = lc; dst += 4;
Since this is an import of a file from newlib, I'm not touching
the formatting or correcting any checkpatch errors.
As for the earlier fix for memset.c, even if the two files for
CRIS v10 and CRIS v32 are identical at the moment, it might
be possible to tweak the CRIS v32 version.
Thus, I'm not yet folding them into the same file, at least not
until we've done some research on it.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com> Cc: Mikael Starvik <starvik@axis.com> Cc: Adrian Bunk <bunk@stusta.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ville Syrjala [Tue, 4 Mar 2008 22:28:47 +0000 (14:28 -0800)]
sm501fb: RGB offsets are reversed in 16bpp modes
The RGB offsets were reversed in 16bpp modes. Simply trying to reverse the
offsets when endianness differs is clearly the wrong thing to do but that is
an issue for another patch.
Signed-off-by: Ville Syrjala <syrjala@sci.fi> Acked-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ville Syrjala [Tue, 4 Mar 2008 22:28:46 +0000 (14:28 -0800)]
sm501fb: direct color visual does not work
The sm501fb palette code clearly does not handle direct color so change the
driver to use true color visual for 16bpp.
Signed-off-by: Ville Syrjala <syrjala@sci.fi> Acked-by: Magnus Damm <damm@igel.co.jp> Acked-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Anton Vorontsov [Tue, 4 Mar 2008 22:28:44 +0000 (14:28 -0800)]
ds1wm: report bus reset error
The patch replaces dev_dbg() by dev_err(), so the user could actually see the
error, instead of wondering why w1 doesn't work. The root cause of the bus
reset error isn't yet debugged though, but this sometimes happens on iPaq
H5555.
And while I'm at it, some cosmetic cleanups also made (few lines were using
spaces instead of tabs).
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com> Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Anton Vorontsov [Tue, 4 Mar 2008 22:28:43 +0000 (14:28 -0800)]
ds1wm: should check for IS_ERR(clk) instead of NULL
On the error condition clk_get() returns ERR_PTR(..), so checking for NULL
doesn't work. ds1wm module causes a kernel oops when ds1wm clock isn't
registered.
This patch converts NULL check to IS_ERR(), plus uses PTR_ERR()
for the return code.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com> Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Grant Likely [Tue, 4 Mar 2008 22:28:42 +0000 (14:28 -0800)]
powerpc: mpc5200: fix build error on mpc52xx_psc_spi device driver
Commit id 94f389485e27641348c1951ab8d65157122a8939 (Separate MPC52xx PSC FIOF
regsiters from the rest of PSC) split the PSC fifo registers away from the
core PSC regs. Doing so broke the mpc52xx_psc_spi driver.
This patch teaches the mpc52xx_psc_spi driver about the new PSC fifo
register definitions.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Cc: David Brownell <david-b@pacbell.net> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Kumar Gala <galak@gate.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Osterlund [Tue, 4 Mar 2008 22:28:41 +0000 (14:28 -0800)]
pktcdvd: reduce stack consumption
On my system, pkt_open() consumes 584 bytes because the compiler decides to
inline lots of functions that would not normally be part of long call chains.
The following patch fixes that problem on my system.
Signed-off-by: Peter Osterlund <petero2@telia.com> Cc: Nix <nix@esperi.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Tue, 4 Mar 2008 22:28:40 +0000 (14:28 -0800)]
add noinline_for_stack
People are adding `noinline' in various places to prevent excess stack
consumption due to gcc inlining. But once this is done, it is quite unobvious
why the `noinline' is present in the code. We can comment each and every
site, or we can use noinline_for_stack.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Krzysztof Helt [Tue, 4 Mar 2008 22:28:39 +0000 (14:28 -0800)]
tridentfb: resource management fixes in probe function
Correct error paths in probe function.
The probe function enables mmio mode so it important to disable the mmio
mode before exiting the probe function. Otherwise, the console is left in
unusable state (garbled fonts at least, lock up at worst).
[akpm@linux-foundation.org: cleanups] Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Balbir Singh [Tue, 4 Mar 2008 22:28:39 +0000 (14:28 -0800)]
Memory controller: rename to Memory Resource Controller
Rename Memory Controller to Memory Resource Controller. Reflect the same
changes in the CONFIG definition for the Memory Resource Controller. Group
together the config options for Resource Counters and Memory Resource
Controller.
Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com> Cc: Paul Menage <menage@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move kprobes examples from Documentation/kprobes.txt to under samples/.
Patch originally by Randy Dunlap.
o Updated the patch to apply on 2.6.25-rc3
o Modified examples code to build on multiple architectures. Currently,
the kprobe and jprobe examples code works for x86 and powerpc
o Cleaned up unneeded #includes
o Cleaned up Kconfig per Sam Ravnborg's suggestions to fix build break
on archs that don't have kretprobes
o Implemented suggestions by Mathieu Desnoyers on CONFIG_KRETPROBES
o Included Andrew Morton's cleanup based on x86-git
o Modified kretprobe_example to act as a arch-agnostic module to
determine routine execution times:
Use 'modprobe kretprobe_example func=<func_name>' to determine
execution time of func_name in nanoseconds.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com> Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add CONFIG_HAVE_KRETPROBES to the arch/<arch>/Kconfig file for relevant
architectures with kprobes support. This facilitates easy handling of
in-kernel modules (like samples/kprobes/kretprobe_example.c) that depend on
kretprobes being present in the kernel.
Thanks to Sam Ravnborg for helping make the patch more lean.
Per Mathieu's suggestion, added CONFIG_KRETPROBES and fixed up dependencies.
Samuel Thibault [Tue, 4 Mar 2008 22:28:36 +0000 (14:28 -0800)]
VT notifier fix for VT switch
VT notifier callbacks need to be aware of console switches. This is already
partially done from console_callback(), but at that time fg_console, cursor
positions, etc. are not yet updated and hence screen readers fetch the old
values.
This adds an update notify after all of the values are updated in
redraw_screen(vc, 1).
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Dumazet [Tue, 4 Mar 2008 22:28:35 +0000 (14:28 -0800)]
alloc_percpu() fails to allocate percpu data
Some oprofile results obtained while using tbench on a 2x2 cpu machine were
very surprising.
For example, loopback_xmit() function was using high number of cpu cycles
to perform the statistic updates, supposed to be real cheap since they use
percpu data
struct pcpu_lstats is a small structure containing two longs. It appears
that on my 32bits platform, alloc_percpu(8) allocates a single cache line,
instead of giving to each cpu a separate cache line.
Using the following patch gave me impressive boost in various benchmarks
( 6 % in tbench)
(all percpu_counters hit this bug too)
Long term fix (ie >= 2.6.26) would be to let each CPU allocate their own
block of memory, so that we dont need to roudup sizes to L1_CACHE_BYTES, or
merging the SGI stuff of course...
Note : SLUB vs SLAB is important here to *show* the improvement, since they
dont have the same minimum allocation sizes (8 bytes vs 32 bytes). This
could very well explain regressions some guys reported when they switched
to SLUB.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Kara [Tue, 4 Mar 2008 22:28:33 +0000 (14:28 -0800)]
vfs: fix NULL pointer dereference in fsync_buffers_list()
Fix NULL pointer dereference in fsync_buffers_list() introduced by recent fix
of races in private_list handling. Since bh->b_assoc_map has been cleared in
__remove_assoc_queue() we should really use original value stored in the
'mapping' variable.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alex Riesen [Tue, 4 Mar 2008 22:28:31 +0000 (14:28 -0800)]
Fix "Malformed early option 'loglevel'"
Keith Mannthey said:
The parameter hotadd_percent is setup right but there is a "Malformed
early option 'numa'" message.
Rusty Russell said:
This happens when the function registered with early_param() returns
non-zero. __setup() functions return 1 if OK, module_param() and
early_param() return 0 or a -ve error code.
Acked-by: Yinghai Lu <yhlu.kernel@gmai.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Keith Mannthey <kmannth@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Roland McGrath [Tue, 4 Mar 2008 22:28:30 +0000 (14:28 -0800)]
core dump: user_regset writeback
This makes the user_regset-based core dump code call user_regset writeback
hooks when available. This is necessary groundwork to allow IA64 to set
CORE_DUMP_USE_REGSET.
Cc: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Roland McGrath <roland@redhat.com> Cc: "Luck, Tony" <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Brownell [Tue, 4 Mar 2008 22:28:27 +0000 (14:28 -0800)]
gpio: <linux/gpio.h> and "no GPIO support here" stubs
Add a <linux/gpio.h> defining fail/warn stubs for GPIO calls on platforms that
don't support the GPIO programming interface. That includes the arch-specific
implementation glue otherwise.
This facilitates a new model for GPIO usage: drivers that can use GPIOs if
they're available, but don't require them. One example of such a driver is
NAND driver for various FreeScale chips. On platforms update with GPIO
support, they can be used instead of a worst-case delay to verify that the
BUSY signal is off.
(Also includes a couple minor unrelated doc updates.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Byron Bradley [Tue, 4 Mar 2008 22:28:25 +0000 (14:28 -0800)]
rtc: add support for the S-35390A RTC chip
This adds basic get/set time support for the Seiko Instruments S-35390A.
This chip communicates using I2C and is used on the QNAP TS-109/TS-209 NAS
devices.
[akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Byron Bradley <byron.bbradley@gmail.com> Acked-by: Jean Delvare <khali@linux-fr.org> Acked-by: David Brownell <david-b@pacbell.net> Tested-by: Tim Ellis <tim@ngndg.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Balbir Singh [Tue, 4 Mar 2008 22:28:24 +0000 (14:28 -0800)]
Memory Resource Controller use strstrip while parsing arguments
The memory controller has a requirement that while writing values, we need
to use echo -n. This patch fixes the problem and makes the UI more consistent.
Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com> Cc: Paul Menage <menage@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jesper Nilsson [Tue, 4 Mar 2008 22:28:23 +0000 (14:28 -0800)]
CRIS v10: Include mm.h instead of vmstat.h in kernel/time.c
Commit 2f569afd9ced9ebec9a6eb3dbf6f83429be0a7b4
(CONFIG_HIGHPTE vs. sub-page page tables) introduced use of
inc_zone_page_state and dec_zone_page_state in include/linux/mm.h.
Those are defined in include/linux/vmstat.h, but after it includes
mm.h, making it impossible to include vmstat.h since inc_zone_page_state
and dec_zone_page_state then would be undefined.
arch/cris/arch-v10/kernel/time.c does just this, which makes the
CRIS v10 build break with the following error:
...
CC arch/cris/arch-v10/kernel/time.o
In file included from include/linux/vmstat.h:7,
from arch/cris/arch-v10/kernel/time.c:17:
include/linux/mm.h: In function 'pgtable_page_ctor':
include/linux/mm.h:902: error: implicit declaration of function 'inc_zone_page_state'
include/linux/mm.h: In function 'pgtable_page_dtor':
include/linux/mm.h:908: error: implicit declaration of function 'dec_zone_page_state'
make[2]: *** [arch/cris/arch-v10/kernel/time.o] Error 1
make[1]: *** [arch/cris/arch-v10/kernel] Error 2
make: *** [sub-make] Error 2
...
By changing kernel/time.c to include linux/mm.h, the build succeeds.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com> Cc: Mikael Starvik <mikael.starvik@axis.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andy Whitcroft [Tue, 4 Mar 2008 22:28:20 +0000 (14:28 -0800)]
update checkpatch.pl to version 0.15
This version brings a number of minor fixes updating the type detector and
the unary tracker. It also brings a few small fixes for false positives.
It also reverts the --file warning. Of note:
- limit CVS checks to added lines
- improved type detections
- fixes to the unary tracker
Andy Whitcroft (13):
Version: 0.15
EXPORT_SYMBOL checks need to accept array variables
export checks must match DECLARE_foo and LIST_HEAD
possible types: cleanup debugging missing line
values: track values through preprocessor conditional paths
typeof is actually a type
possible types: detect definitions which cross lines
values: include line numbers on value debug information
values: ensure we find correctly record pending brackets
values: simplify the brace history stack
CVS keyword checks should only apply to added lines
loosen spacing for comments
allow braces for single statement blocks with multiline conditionals
Li Zefan [Tue, 4 Mar 2008 22:28:19 +0000 (14:28 -0800)]
cgroup: fix default notify_on_release setting
The documentation says the default value of notify_on_release of a child
cgroup is inherited from its parent, which is reasonable, but the
implementation just sets the flag disabled.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Acked-by: Paul Menage <menage@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jussi Kivilinna [Tue, 4 Mar 2008 18:05:27 +0000 (20:05 +0200)]
rndis_wlan: fix broken data copy
Replace broken code that attempted to copy 6 byte array to 64-bit
integer. Due to missing cast to 64-bit integer, left shift operation
were 32-bit and lead to bytes been copied over each other. New code
uses simple memcpy, for greater readability and efficiency.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 29 Feb 2008 22:28:25 +0000 (23:28 +0100)]
p54: fix eeprom parser length sanity checks
When I called p54_parse_eeprom() on a hand-coded structure
I managed to make a small mistake with wrap->len which caused
a segfault a few lines down when trying to read entry->len.
This patch changes the validation code to avoid such problems.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Tested-by: Florian Fainelli <florian.fainelli@telecomint.eu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 29 Feb 2008 12:56:33 +0000 (13:56 +0100)]
p54: fix EEPROM structure endianness
Since the EEPROM structure is read from hardware, it is
always little endian, annotate that in the struct and
make sure to convert where applicable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: Michael Wu <flamingice@sourmilk.net> Tested-by: Florian Fainelli <florian.fainelli@telecomint.eu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / linux-2.6 / log