Hermann Pitton [Mon, 21 Aug 2006 17:14:33 +0000 (14:14 -0300)]
V4L/DVB (4511): Restore tuner_ymec_tvf66t5_b_dff_pal_ranges[] to fix UHF switch functionality
The tena_9533_di_pal_ranges use 0x04 instead the original 0x08 for the
UHF (range 2) switching. This is wrong and therefore nothing happens.
Restore tuner_ymec_tvf66t5_b_dff_pal_ranges[] to make the UHF switch
working again.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de> Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Jack Steiner [Thu, 31 Aug 2006 16:35:57 +0000 (11:35 -0500)]
[IA64] SN fix for cpu hotplug/kexec
The sn_cpu_init() is required for cpu initialization on SN platforms.
Change __init to __cpuinit so that the function is not freed with init code/data.
Signed-off-by: Jack Steiner <steiner@sgi.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
Jack Steiner [Thu, 31 Aug 2006 16:34:47 +0000 (11:34 -0500)]
[IA64] Save register stack contents on cpu start
The SN PROM uses the register stack in the slave loop. The contents
must be preserved for the OS to return to the slave loop via offlining
a cpu or for kexec. A 'flushrs" is needed to force the stack to be written
to memory prior to changing bspstore.
Signed-off-by: Jack Steiner <steiner@sgi.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
Andreas Schwab [Mon, 4 Sep 2006 19:56:09 +0000 (21:56 +0200)]
[IA64] Unwire set/get_robust_list
The syscalls set/get_robust_list must not be wired up until
futex_atomic_cmpxchg_inatomic is implemented. Otherwise the kernel will
hang in handle_futex_death.
Signed-off-by: Andreas Schwab <schwab@suse.de> Signed-off-by: Tony Luck <tony.luck@intel.com>
[PATCH] NFS: large non-page-aligned direct I/O clobbers memory
The logic in nfs_direct_read_schedule and nfs_direct_write_schedule can
allow data->npages to be one larger than rpages. This causes a page
pointer to be written beyond the end of the pagevec in nfs_read_data (or
nfs_write_data).
Fix this by making nfs_(read|write)_alloc() calculate the size of the
pagevec array, and initialise data->npages.
Also get rid of the redundant argument to nfs_commit_alloc().
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com> Cc: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Morton [Fri, 8 Sep 2006 16:48:38 +0000 (09:48 -0700)]
[PATCH] invalidate_complete_page() race fix
If a CPU faults this page into pagetables after invalidate_mapping_pages()
checked page_mapped(), invalidate_complete_page() will still proceed to remove
the page from pagecache. This leaves the page-faulting process with a
detached page. If it was MAP_SHARED then file data loss will ensue.
Fix that up by checking the page's refcount after taking tree_lock.
Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Hugh Dickins <hugh@veritas.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Looking at the code, it looks like it's not handle HOLE correctly. It ends
up returning -EIO. Here is the patch to fix it.
If we really want to be paranoid, we can allow return values 0 (HOLE), 1
(we asked for one block) and return -EIO for more than 1 block. But I
really don't see a reason for doing it - all we need is the block# here.
(doesn't matter how many blocks are mapped).
ext3_get_blocks_handle() returns number of blocks it mapped. It returns 0
in case of HOLE. ext3_getblk() should handle HOLE properly (currently its
dumping warning stack and returning -EIO).
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com> Acked-by: Mingming Cao <cmm@us.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Wang [Fri, 8 Sep 2006 16:47:51 +0000 (09:47 -0700)]
[PATCH] sis5513: add SiS south bridge ID 0x966 and 0x968
New SiS south bridge device ID is 0x966.
Next coming product will be 0x968. (Will be released in Q4, this year)
We don't make any updates to the IDE controller.
Signed-off-by: David Wang <touch@sis.com> Cc: Jeff Garzik <jeff@garzik.org> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Thomas Gleixner [Fri, 8 Sep 2006 16:47:15 +0000 (09:47 -0700)]
[PATCH] Use the correct restart option for futex_lock_pi
The current implementation of futex_lock_pi returns -ERESTART_RESTARTBLOCK
in case that the lock operation has been interrupted by a signal. This
results in a return of -EINTR to userspace in case there is an handler for
the signal. This is wrong, because userspace expects that the lock
function does not return in any case of signal delivery.
This was not caught by my insufficient test case, but triggered a nasty
userspace problem in an high load application scenario. Unfortunately also
glibc does not check for this invalid return value.
Using -ERSTARTNOINTR makes sure, that the interrupted syscall is restarted.
The restart block related code can be safely removed, as the possible
timeout argument is an absolute time value.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This prevents cross-region mappings on IA64 and SPARC which could lead
to system crash. They were correctly trapped for normal mmap() calls,
but not for the kernel internal calls generated by executable loading.
This code just moves the architecture-specific cross-region checks into
an arch-specific "arch_mmap_check()" macro, and defines that for the
architectures that needed it (ia64, sparc and sparc64).
Architectures that don't have any special requirements can just ignore
the new cross-region check, since the mmap() code will just notice on
its own when the macro isn't defined.
Signed-off-by: Pavel Emelianov <xemul@openvz.org> Signed-off-by: Kirill Korotaev <dev@openvz.org> Acked-by: David Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[ Cleaned up to not affect architectures that don't need it ] Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] Move linux/device.h include in linux/atmdev.h to #ifdef __KERNEL__ section
linux/device.h header is not included in the David Woodhouse's
kernel-headers git tree which is used for userspace kernel headers. Which
results in compile errors when building iproute2. Attached patch moves
linux/device.h include under the #ifdef __KERNEL__ section.
Signed-off-by: Ismail Donmez <ismail@pardus.org.tr> Signed-off-by: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pavel Machek [Wed, 6 Sep 2006 07:03:43 +0000 (00:03 -0700)]
[PATCH] prevent swsusp with PAE
PAE + swsusp results in hard-to-debug crash about 50% of time during
resume. Cause is known, fix needs to be ported from x86-64 (but we can't
make it to 2.6.18, and I'd like this to be worked around in 2.6.18).
Signed-off-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Thomas Gleixner [Wed, 6 Sep 2006 07:03:42 +0000 (00:03 -0700)]
[PATCH] prevent timespec/timeval to ktime_t overflow
Frank v. Waveren pointed out that on 64bit machines the timespec to
ktime_t conversion might overflow. This is also true for timeval to
ktime_t conversions. This breaks a "sleep inf" on 64bit machines.
While a timespec/timeval with tx.sec = MAX_LONG is valid by specification
the internal representation of ktime_t is based on nanoseconds. The
conversion of seconds to nanoseconds overflows for seconds values >=
(MAX_LONG / NSEC_PER_SEC).
Check the seconds argument to the conversion and limit it to the maximum
time which can be represented by ktime_t.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Frank v Waveren <fvw@var.cx> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] powerpc: Fix typo in powermac platform functions
New sparse caught that typo which could have caused erratic hardware
behaviour on some machines if the platform functions are used by the
firmware to change bits in some FCR registers.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/home/rmk/linux-2.6-serial:
[SERIAL] 8250: constify some serial structs
[SERIAL] Make uart_match_port() work with all memory mapped UARTs
[PATCH] eligible_child: remove an obsolete ->tgid check
It is not possible to find a sub-thread in ->children/->ptrace_children
lists, ptrace_attach() does not allow to attach to sub-threads.
Even if it was possible to ptrace the task from the same thread group,
we can't allow to release ->group_leader while there are others (ptracer)
threads in the same group.
Resolve ARM1136 VIPT non-aliasing cache coherency issues observed when
using ptrace to set breakpoints and cleanup copy_{to,from}_user_page()
while we're here as requested by Russell King because "it's also far
too heavy on non-v6 CPUs".
NOTES:
1. Only access_process_vm() calls copy_{to,from}_user_page().
2. access_process_vm() calls get_user_pages() to pin down the "page".
3. get_user_pages() calls flush_dcache_page(page) which ensures cache
coherency between kernel and userspace mappings of "page". However
flush_dcache_page(page) may not invalidate I-Cache over this range
for all cases, specifically, I-Cache is not invalidated for the VIPT
non-aliasing case. So memory is consistent between kernel and user
space mappings of "page" but I-Cache may still be hot over this
range. IOW, we don't have to worry about flush_cache_page() before
memcpy().
4. Now, for the copy_to_user_page() case, after memcpy(), we must flush
the caches so memory is consistent with kernel cache entries and
invalidate the I-Cache if this mm region is executable. We don't
need to do anything after memcpy() for the copy_from_user_page()
case since kernel cache entries will be invalidated via the same
process above if we access "page" again. The flush_ptrace_access()
function (borrowed from SPARC64 implementation) is added to handle
cache flushing after memcpy() for the copy_to_user_page() case.
Signed-off-by: George G. Davis <gdavis@mvista.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6:
uhci-hcd: fix list access bug
USB: Support for ELECOM LD-USB20 in pegasus
USB: Add VIA quirk fixup for VT8235 usb2
USB: rtl8150_disconnect() needs tasklet_kill()
USB Storage: unusual_devs.h for Sony Ericsson M600i
USB Storage: Remove the finecam3 unusual_devs entry
UHCI: don't stop at an Iso error
usb gadget: g_ether spinlock recursion fix
USB: add all wacom device to hid-core.c blacklist
hid-core.c: Adds all GTCO CalComp Digitizers and InterWrite School Products to blacklist
USB floppy drive SAMSUNG SFD-321U/EP detected 8 times
Since vma->vm_pgoff is in units of smallpages, VMAs for huge pages have the
lower HPAGE_SHIFT - PAGE_SHIFT bits always cleared, which results in badd
offsets to the interleave functions. Take this difference from small pages
into account when calculating the offset. This does add a 0-bit shift into
the small-page path (via alloc_page_vma()), but I think that is negligible.
Also add a BUG_ON to prevent the offset from growing due to a negative
right-shift, which probably shouldn't be allowed anyways.
Tested on an 8-memory node ppc64 NUMA box and got the interleaving I
expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com> Signed-off-by: Adam Litke <agl@us.ibm.com> Cc: Andi Kleen <ak@muc.de> Acked-by: Christoph Lameter <clameter@engr.sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Problems fixed are:
- Call to default_hwif_mmiops() was not being done until _after_
first IO operation, resulting in the first IO operation being
done as a port IO op, instead of memio.
- request_region() calls needed to be request_mem_region()
- Incomplete error case handling.
- Non-usage of ioremap() and __iomem.
Signed-off-by: John Keller <jpk@sgi.com> Signed-off-by: Jeremy Higdon <jeremy@sgi.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The port to genirq & the new powerpc interrupt model in 2.6.18 introduced a
bug in the legacy PowerMac PIC code (used on older machines) because of a
typo potentially causing hangs due to interrupt storms. This fixes it,
along with a performance issue causing us to do spurrious retriggers after
masking an interrupt.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The via-pmu backlight code (introduced in 2.6.18) has various design issues
causing crashes on machines using it like the old Wallstreet powerbook
(Michael, the author, never managed to test on these and I just got my hand
on one of those old beasts).
This fixes them by no longer trying to hijack the backlight device of the
frontmost framebuffer (causing that framebuffer to crash) but having it's
own local bits instead. Might look weird but it's better that way on those
old machines, at least as a last-minute fix for 2.6.18. We might rework
the whole thing later. This patch also changes the way it gets notified of
sleep and wakeup in order to properly shut the backlight down on sleep and
bring it back on wakeup.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pavel Mironchik [Fri, 1 Sep 2006 04:27:47 +0000 (21:27 -0700)]
[PATCH] dm: work around mempool_alloc, bio_alloc_bioset deadlocks
This patch works around a complex dm-related deadlock/livelock down in the
mempool allocator.
Alasdair said:
Several dm targets suffer from this.
Mempools are not yet used correctly everywhere in device-mapper: they can
get shared when devices are stacked, and some targets share them across
multiple instances. I made fixing this one of the prerequisites for this
patch:
which in some cases makes people more likely to hit the problem.
There's been some progress on this recently with (unfinished) dm-crypt
patches at:
http://www.kernel.org/pub/linux/kernel/people/agk/patches/2.6/editing/
(dm-crypt-move-io-to-workqueue.patch plus dependencies)
and:
I've no problems with a temporary workaround like that, but Milan Broz (a
new Redhat developer in the Czech Republic) has started reviewing all the
mempool usage in device-mapper so I'm expecting we'll soon have a proper fix
for this associated problems. [He's back from holiday at the start of next
week.]
For now, this sad-but-safe little patch will allow the machine to recover.
[akpm@osdl.org: rewrote changelog] Cc: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] IPMI: fix occasional oops on module unload
Olaf Kirch of SuSE tracked down a problem where module unloads of the IPMI
driver would occasionally result in Oopses. He tracked that down to a
variable that wasn't always initialized properly in some situations. This
patch initializes that variable. Olaf sent a patch that kzalloc-ed the
data, but this structure is large enough that I would perfer to not do
that. Thanks Olaf!
Signed-off-by: Corey Minyard <minyard@acm.org> Cc: Olaf Kirch <okir@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Olaf Hering [Fri, 1 Sep 2006 04:27:41 +0000 (21:27 -0700)]
[PATCH] exit early in floppy_init when no floppy exists
modprobe -v floppy on a Apple G5 writes incorrect stuff to dmesg:
Floppy drive(s): fd0 is 2.88M
The reason is that the legacy io check happens very late,
when part of the floppy stuff is already initialized.
check_legacy_ioport() returns either -ENODEV right away, or it walks
the device-tree looking for a floppy node.
Signed-off-by: Olaf Hering <olaf@aepfle.de> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Cleanup allocation and freeing of tsk->delays used by delay accounting.
This solves two problems reported for delay accounting:
1. oops in __delayacct_blkio_ticks
http://www.uwsg.indiana.edu/hypermail/linux/kernel/0608.2/1844.html
Currently tsk->delays is getting freed too early in task exit which can
cause a NULL tsk->delays to get accessed via reading of /proc/<tgid>/stats.
The patch fixes this problem by freeing tsk->delays closer to when
task_struct itself is freed up. As a result, it also eliminates the use of
tsk->delays_lock which was only being used (inadequately) to safeguard
access to tsk->delays while a task was exiting.
2. Possible memory leak in kernel/delayacct.c
http://www.uwsg.indiana.edu/hypermail/linux/kernel/0608.2/1389.html
The patch cleans up tsk->delays allocations after a bad fork which was
missing earlier.
The patch has been tested to fix the problems listed above and stress
tested with rapid calls to delay accounting's taskstats command interface
(which is the other path that can access the same data, besides the /proc
interface causing the oops above).
john stultz [Fri, 1 Sep 2006 04:27:37 +0000 (21:27 -0700)]
[PATCH] Fix faulty HPET clocksource usage (fix for bug #7062)
Apparently some systems export valid HPET addresses, but hpet_enable()
fails. Then when the HPET clocksource starts up, it only checks for a
valid HPET address, and the result is a system where time does not advance.
See http://bugme.osdl.org/show_bug.cgi?id=7062 for details.
This patch just makes sure we better check that the HPET is functional
before registering the HPET clocksource.
Signed-off-by: John Stultz <johnstul@us.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix receive tty error handling in synclink_gt driver. Adrian reported
compiler warning for incorrect bit test against char variable. I
determined these and other device specific error bits were incorrectly
defined.
Signed-off-by: Paul Fulghum <paulkf@microgate.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] md: Fix issues with referencing rdev in md/raid1
We need to be careful when referencing mirrors[i].rdev. It can disappear
under us at various times.
So:
fix a couple of problem places.
comment a couple of non-problem places
move an 'atomic_add' which deferences rdev down a little
way to some where where it is sure to not be NULL.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] ZVC: Scale thresholds depending on the size of the system
The ZVC counter update threshold is currently set to a fixed value of 32.
This patch sets up the threshold depending on the number of processors and
the sizes of the zones in the system.
With the current threshold of 32, I was able to observe slight contention
when more than 130-140 processors concurrently updated the counters. The
contention vanished when I either increased the threshold to 64 or used
Andrew's idea of overstepping the interval (see ZVC overstep patch).
However, we saw contention again at 220-230 processors. So we need higher
values for larger systems.
But the current default is already a bit of an overkill for smaller
systems. Some systems have tiny zones where precision matters. For
example i386 and x86_64 have 16M DMA zones and either 900M ZONE_NORMAL or
ZONE_DMA32. These are even present on SMP and NUMA systems.
The patch here sets up a threshold based on the number of processors in the
system and the size of the zone that these counters are used for. The
threshold should grow logarithmically, so we use fls() as an easy
approximation.
Results of tests on a system with 1024 processors (4TB RAM)
The following output is from a test allocating 1GB of memory concurrently
on each processor (Forking the process. So contention on mmap_sem and the
pte locks is not a factor):
Increments and decrements are usually grouped rather than mixed. We can
optimize the inc and dec functions for that case.
Increment and decrement the counters by 50% more than the threshold in
those cases and set the differential accordingly. This decreases the need
to update the atomic counters.
The idea came originally from Andrew Morton. The overstepping alone was
sufficient to address the contention issue found when updating the global
and the per zone counters from 160 processors.
Also remove some code in dec_zone_page_state.
Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Alan Stern [Thu, 31 Aug 2006 18:18:39 +0000 (14:18 -0400)]
uhci-hcd: fix list access bug
When skipping to the last TD of an URB, go to the _last_ entry in the
list instead of the _first_ entry (as780). This fixes Bugzilla #6747
and possibly others.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mark Hindley [Mon, 28 Aug 2006 19:43:25 +0000 (20:43 +0100)]
USB: Add VIA quirk fixup for VT8235 usb2
Patch to add VIA PCI quirk for Enhanced/Extended USB on VT8235
southbridge. It is needed in order to use EHCI/USB 2.0 with ACPI.
Without it IRQs are not routed correctly, you get an "Unlink after
no-IRQ?" error and the device is unusable.
I belive this could also be a fix for Bugzilla Bug 5835.
Signed-off-by: Mark Hindley <mark@hindley.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Phil Dibowitz [Thu, 24 Aug 2006 04:11:01 +0000 (21:11 -0700)]
USB Storage: Remove the finecam3 unusual_devs entry
This patch removes the Kyocera Finecam L3 entry in unusual devices
originally submitted by Michael Krauth <michael.krauth@web.de> and
Alessandro Fracchetti <al.fracchetti@tin.it> given that Gerriet
<ger.haw@gmx.de> finds he doesn't need it and Alessandro confirms it
isn't needed anymore as well.
Signed-off-by: Phil Dibowitz <phil@ipom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 21 Aug 2006 15:58:50 +0000 (11:58 -0400)]
UHCI: don't stop at an Iso error
Unlike other sorts of endpoint queues, Isochronous queues don't stop
when an error is encountered. This patch (as772) fixes the scanning
routine in uhci-hcd, to make it keep on going when it finds an Iso
error.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Mon, 21 Aug 2006 22:26:38 +0000 (15:26 -0700)]
usb gadget: g_ether spinlock recursion fix
The new spinlock debug code turned up a spinlock recursion bug in the
Ethernet gadget driver on a disconnect path; it would show up with any
UDC driver where the cancellation of active requests was synchronous,
rather than e.g. delayed until a controller's completion IRQ.
That recursion is fixed here by creating and using a new spinlock to
protect the relevant lists.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Roland Dreier [Thu, 31 Aug 2006 23:43:06 +0000 (16:43 -0700)]
IB/mthca: Use IRQ safe locks to protect allocation bitmaps
It is supposed to be OK to call mthca_create_ah() and mthca_destroy_ah()
from any context. However, for mem-full HCAs, these functions use the
mthca_alloc() and mthca_free() bitmap helpers, and those helpers use
non-IRQ-safe spin_lock() internally. Lockdep correctly warns that
this could lead to a deadlock. Fix this by changing mthca_alloc() and
mthca_free() to use spin_lock_irqsave().
Wei Dong [Thu, 31 Aug 2006 22:24:48 +0000 (15:24 -0700)]
[IPV4]: Fix SNMPv2 "ipFragFails" counter error
When I tested Linux kernel 2.6.17.7 about statistics
"ipFragFails",found that this counter couldn't increase correctly. The
criteria is RFC2011:
RFC2011
ipFragFails OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IP datagrams that have been discarded because
they needed to be fragmented at this entity but could not
be, e.g., because their Don't Fragment flag was set."
::= { ip 18 }
When I send big IP packet to a router with DF bit set to 1 which need to
be fragmented, and router just sends an ICMP error message
ICMP_FRAG_NEEDED but no increments for this counter(in the function
ip_fragment).
Signed-off-by: Wei Dong <weid@nanjing-fnst.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup for include/asm-arma/arch-s3c2410/dma.h,
by using tab characters to indent items, remove the
now un-necessary changelog, and update the copyright
information.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ben Dooks [Thu, 31 Aug 2006 14:26:37 +0000 (15:26 +0100)]
[ARM] 3764/1: S3C24XX: change type naming to kernel style
Patch from Ben Dooks
The type naming in the s3c24xx dma code is riddled with
typedefs creating _t types, from the code import from 2.4
which is contrary to the current Kernel coding style.
This patch cleans this up, removing the typedefs and
and fixing up the resultant code changes.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
David Brownell [Thu, 31 Aug 2006 14:26:35 +0000 (15:26 +0100)]
[ARM] 3763/1: add both rtcs to csb337 defconfig
Patch from David Brownell
This adds RTC support to the csb337 default config. Both the AT91
and the ds1307 RTCs are enabled (rtc0 and rtc1 respectively).
The ds1307 is used to initialize the system time, since it's battery-backed.
From then on the AT91 RTC is used, since it's more capable (with both
alarm and update irqs, and system wakeup capability) even though it
needs manual initialization (symlink /dev/rtc to /dev/rtc0 for older
versions of hwclock, then "hwclock --systohc") in an rc script or
from inittab.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds [Thu, 31 Aug 2006 04:44:06 +0000 (21:44 -0700)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fix return value from memcpy
[POWERPC] iseries: Define insw et al. so libata/ide will compile
[POWERPC] Fix irq enable/disable in smp_generic_take_timebase
[POWERPC] Fix problem with time not advancing on 32-bit platforms
[POWERPC] Restore copyright notice in arch/powerpc/kernel/fpu.S
[POWERPC] Fix up ibm_architecture_vec definition
[POWERPC] Make OF irq map code detect more error cases
[POWERPC] Support for "weird" MPICs and fixup mpc7448_hpc2
[POWERPC] Fix MPIC sense codes in documentation
[POWERPC] Fix performance regression in IRQ radix tree locking
[POWERPC] Add mpc7448hpc2 device tree source file
[POWERPC] Add MPC8349E MDS device tree source file to arch/powerpc/boot/dts
[POWERPC] modify mpc83xx platforms to use new IRQ layer
[POWERPC] Adapt ipic driver to new host_ops interface, add set_irq_type to set IRQ sense
[POWERPC] back up old school ipic.[hc] to arch/ppc
[POWERPC] Use mpc8641hpcn PIC base address from dev tree.
[POWERPC] Allow MPC8641 HPCN to build with CONFIG_PCI disabled too.
[POWERPC] Fix powerpc 44x_mmu build
[POWERPC] Remove flush_dcache_all export
Paul Mackerras [Wed, 30 Aug 2006 06:13:16 +0000 (16:13 +1000)]
[PATCH] ppc32: fix last_jiffy time comparison
This fixes a hang on ppc32.
The problem was that I was comparing a 32-bit quantity with a 64-bit
quantity, and consequently time wasn't advancing. This makes us use a
64-bit quantity on all platforms, which ends up simplifying the code
since we can now get rid of the tb_last_stamp variable (which actually
fixes another bug that Ben H and I noticed while going carefully through
the code).
This works fine on my G4 tibook. Let me know how it goes on your
machines.
Acked-by: Olaf Hering <olaf@aepfle.de> Acked-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] fbdev: Fix crashes in various fbdev's blank routines
The backlight changes that went in had a bug where they could cause the
kernel to access an unitialized pointer when blanking if there is no
backlight control on a machine.
The bug affects atyfb, aty128fb, nvidiafb and rivafb. radeonfb seems to
be ok. This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paul Mackerras [Thu, 31 Aug 2006 03:22:58 +0000 (13:22 +1000)]
[POWERPC] Fix return value from memcpy
As pointed out by Herbert Xu <herbert@gondor.apana.org.au>, our
memcpy implementation didn't return the destination pointer as its
return value, and there is code in the kernel that expects that.
This fixes it.
Linus Torvalds [Thu, 31 Aug 2006 00:12:11 +0000 (17:12 -0700)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Increase default nodes shift to 10, nr_cpus to 1024
[IA64] remove redundant local_irq_save() calls from sn_sal.h
[IA64] panic if topology_init kzalloc fails
[IA64-SGI] Silent data corruption caused by XPC V2.
Alan Cox [Wed, 30 Aug 2006 18:14:25 +0000 (19:14 +0100)]
[PATCH] Missing PCI id update for VIA IDE
The following change from -mm is important to 2.6.18 (actually to 2.6.17
but its too late for that). This was contributed over three months ago
by VIA to Bartlomiej and nothing happened. As a result the new chipset
is now out and Linux won't run on it. By the time 2.6.18 is finalised
this will be the defacto standard VIA chipset so support would be a good
plan.
Tested in -mm for a while, its essentially a PCI ident update but for
the bridge chip because VIA do things in weird ways.
Suleiman Souhlal [Wed, 30 Aug 2006 17:37:20 +0000 (19:37 +0200)]
[PATCH] x86_64: Don't write out segments from vsyscall32 DSO if it is not mapped
It's possible to get an invalid page fault in kernel mode when we try to
write out segments from vsyscall32 when dumping core for a 32bit process if
the vsyscall32 DSO is not mapped in its address space (which can happen if,
for example, ulimit -v 100 is run).
Keith Owens [Wed, 30 Aug 2006 17:37:19 +0000 (19:37 +0200)]
[PATCH] x86_64: Save original IST values for checking stack addresses
The values in init_tss.ist[] can change when an IST event occurs. Save
the original IST values for checking stack addresses when debugging or
doing stack traces.
Andi Kleen [Wed, 30 Aug 2006 17:37:15 +0000 (19:37 +0200)]
[PATCH] x86: Disable MMCONFIG on Intel SDV using DMI blacklist
As a replacement for the earlier removal of the e820 MCFG check
we blacklist the Intel SDV with the original BIOS bug that
motivated that check. On those machines don't use MMCONFIG.
This also adds a new pci=mmconf parameter to override the blacklist.
Cc: Greg KH <gregkh@suse.de> Cc: Arjan van de Ven <arjan@infradead.org> Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen [Wed, 30 Aug 2006 17:37:12 +0000 (19:37 +0200)]
[PATCH] x86_64: Recover 1MB of kernel memory
Noticed by Jan Beulich.
When the kernel was moved from 1MB to 2MB in 2.6.17 the kernel reservation
code wasn't adjusted and it still reserved starting with 1MB. This means 1MB always
were lost.
This patch fixes this by reserving only starting with _text.
Jan Beulich [Wed, 30 Aug 2006 17:37:11 +0000 (19:37 +0200)]
[PATCH] x86: Make backtracer fallback logic more bullet-proof
The unwinder fallback logic still had potential for falling through to
the legacy stack trace code without printing an indication (at once
serving as a separator) of this.
Further, the stack pointer retrieval for the fallback should be as
restrictive as possible (in order to avoid having the legacy stack
tracer try to access invalid memory). The patch tightens that, but
this could certainly be further improved.
Also making the call_trace command line option now conditional upon
CONFIG_STACK_UNWIND (as it's meaningless otherwise).
Jan Beulich [Wed, 30 Aug 2006 17:37:10 +0000 (19:37 +0200)]
[PATCH] x86: fix x86 cpuid keys used in alternative_smp()
By hard-coding the cpuid keys for alternative_smp() rather than using
the symbolic constant it turned out that incorrect values were used on
both i386 (0x68 instead of 0x69) and x86-64 (0x66 instead of 0x68).
One open question: Should this added push perhaps be made conditional
upon CONFIG_STACK_UNWIND or CONFIG_UNWIND_INFO?
[AK: not needed, these are all very slow paths]
One open question: Should these added pushes perhaps be made
conditional upon CONFIG_STACK_UNWIND or CONFIG_UNWIND_INFO?
[AK: Not needed -- these are all very slow paths]
Andi Kleen [Wed, 30 Aug 2006 17:37:06 +0000 (19:37 +0200)]
[PATCH] x86: Revert e820 MCFG heuristics
The check for the MCFG table being reserved in the e820 map was originally
added to detect a broken BIOS in a preproduction Intel SDV. However it also
breaks the Apple x86 Macs, which can't supply this properly, but need
a working MCFG. With this patch they wouldn't use the MCFG and not work.
After some discussion I think it's best to remove the heuristic again.
It also failed on some other boxes (although it didn't cause much
problems there because old style port access for PCI config space
still works as fallback), but the preproduction SDVs can just use
pci=nommcfg. Supporting production machines properly is more
important.
Edgar Hucek did all the debugging work.
Cc: Arjan van de Ven <arjan@infradead.org> Cc: Edgar Hucek <hostmaster@ed-soft.at> Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[ARM] 3750/3: Fix double VFP emulation for EABI kernels
Patch from Daniel Jacobowitz
vfp_put_double didn't work in a CONFIG_AEABI kernel. By swapping
the arguments, we arrange for them to be in the same place regardless
of ABI. I made the same change to vfp_put_float for consistency.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
projects / linux-2.6 / log