Jonathan Phenix [Tue, 19 Jun 2007 16:31:28 +0000 (18:31 +0200)]
[ALSA] hda-codec - Output MFG information for HDA devices
This patch output information about the MFG (Modem Function Group) to
the /proc/asound/card?/codec#? file. This information is important to
identify if a HDA device has a modem or not.
Signed-off-by: Jonathan Phenix <jonathan@linuxant.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Matthew Ranostay [Tue, 19 Jun 2007 14:48:28 +0000 (16:48 +0200)]
[ALSA] hda: add eapd support to additional idt codecs
Added support for EAPD on the 927x, and 9227-8 IDT HDA codecs.
Enabling EAPD powers the internal speaker amp otherwise there is no
sound on systems with an internal amp.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Somewhere when dealing with the s3c24xx patches and requested changes I
managed to miss this file on re-submission.
Its a header file required for compilation of neo1973-wm8573.c and
should be a no brainer.
Takashi Iwai [Fri, 8 Jun 2007 10:25:25 +0000 (12:25 +0200)]
[ALSA] hda-codec - Fix Thinkpad X61/T61 outputs
Enable EAPD bit on Thinkpad X61/T61. The recent model requires it
explicitly to make any sounds. In future, it should be toggled
automatically on demand.
Also, added a beep volume/switch. Some people like it although I
don't understand why :)
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Dave Jones [Wed, 6 Jun 2007 12:48:52 +0000 (14:48 +0200)]
[ALSA] Yet another Uniwill laptop with ALC861 codec
From: Dave Jones <davej@redhat.com>
Rediffed version of the patch from ..
http://bugzilla.kernel.org/show_bug.cgi?id=8016
that seems to be lingering for some time.
Original patch by: Andy Shevchenko <andy@smile.org.ua>
Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
STAC922x provides the capture boost level up to 4, but actually it
works only up to 2. Since the range of the mixer is automatically
defined from amp-capability bits, we need to override the value
beforehand. snd_hda_override_amp_caps() is introduced for this
purpose.
The function patch_stac922x() calls this for NID 0x12 (Mux Capture
Volume). This should fix another recording problem on Intel Macs.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Ivan N. Zlatev [Tue, 29 May 2007 14:03:00 +0000 (16:03 +0200)]
[ALSA] hda-codec - Fix pin configs for Intel Macs
* adds the pinconfigs for all 5 Apple boards and 14 Subsystem IDs
(support for possibly all iMac, Mac, MacMini etc etc)
* adds 'intel-mac-v1' to v5 models which replace the current
* reflects changes in Alsa-Configuration.txt
Signed-off-by: Ivan N. Zlatev <contact@i-nz.net> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Adrian McMenamin [Fri, 18 May 2007 12:26:59 +0000 (14:26 +0200)]
[ALSA] Add ALSA support for the SEGA Dreamcast PCM device
ALSA support for the SEGA Dreamcast Yamaha AICA sound device (pcm)
This patch adds ALSA sound support for pcm playback on two channels on
the SEGA Dreamcast built-in sound device (the Yamaha AICA)
Add driver for the AICA sound device built into the SEGA Dreamcast
Hook it all up with the build system.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Manuel Lauss [Mon, 14 May 2007 16:40:07 +0000 (18:40 +0200)]
[ALSA] SH7760 ASoC support
ALSA ASoC support for SH7760
This patch adds ALSA ASoC drivers for the Audio interfaces
of the SH7760 SoC:
Add driver for the SH7760 DMA engine (dmabrg)
Add AC97 driver for HAC unit(s) found on SH7760/SH7780
Add I2S driver for SSI unit(s) found on SH7760/SH7780
Add a generic SH7760-AC97 machine driver.
Hook it all up with the build system.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds ALSA support for the Openmoko Neo1973 phone. Features:-
* HiFi Playback and capture.
* Phone calls supported.
* Support for BT PCM in WM8753 voice interface.
* Support for LM4857 audio amp.
Daniel Drake [Thu, 10 May 2007 06:52:19 +0000 (08:52 +0200)]
[ALSA] usb-audio: another Logitech QuickCam ID
This patch adds the ID for another quickcam microphone, reported by freqmod
on ALSA ticket #0003040
I'm going to submit a USB patch separately to provide a macro to simplify these
entries, as suggested by Alan Stern. We could switch to using that in future.
Signed-off-by: Daniel Drake <dsd@gentoo.org> Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Takashi Iwai [Wed, 20 Jun 2007 10:03:09 +0000 (12:03 +0200)]
[ALSA] Fix unfreed pnp driver in opti9xx ISA driver
- Added the missing pnp_unregister_card_driver() in the case ISA PnP
isn't found, which caused an error at kobject_add with -EEXIST
Jun 11 09:07:31 rain kernel: kobject_add failed for opti9xx with -EEXIST, don't try to register things with the same name in the same directory.
Jun 11 09:07:31 rain kernel: [<c01c18fa>] kobject_shadow_add+0x12a/0x1c0
Jun 11 09:07:31 rain kernel: [<c01c1a81>] kobject_register+0x21/0x50
Jun 11 09:07:31 rain kernel: [<c01f09a2>] bus_add_driver+0x72/0x1b0
Jun 11 09:07:31 rain kernel: [<c01d3dff>] pnp_register_card_driver+0x4f/0xc0
Jun 11 09:07:31 rain kernel: [<c89bc00a>] alsa_card_opti9xx_init+0xa/0x25 [snd_opti92x_ad1848]
Jun 11 09:07:31 rain kernel: [<c0136947>] sys_init_module+0x157/0x1610
Jun 11 09:07:31 rain kernel: [<c01029b4>] syscall_call+0x7/0xb
- Fixed the probe behavior when no PnP is set up. Now it behaves
like the former version.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Paul Mundt [Fri, 20 Jul 2007 01:11:58 +0000 (10:11 +0900)]
mm: Remove slab destructors from kmem_cache_create().
Slab destructors were no longer supported after Christoph's c59def9f222d44bb7e2f0a559f2906191a0862d7 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Al Viro [Thu, 19 Jul 2007 23:23:31 +0000 (00:23 +0100)]
coda breakage
a) switch by loff_t == __cmpdi2 use. Replaced with a couple
of obvious ifs; update of ->f_pos in the first one makes sure that we
do the right thing in all cases.
b) block_signals() and unblock_signals() are globals on UML.
Renamed coda ones; in principle UML probably ought to do rename as
well, but that's another story.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that ide-floppy supports SG_IO we can add support for SCSI ioctls
(except deprecated SCSI_IOCTL_SEND_COMMAND and legacy CDROM_SEND_PACKET
ones - we can add them later iff really needed).
While at it remove handling of CDROMEJECT and CDROMCLOSETRAY ioctls from
generic_ide_ioctl():
- This prevents ide-{disk,tape,scsi} device drivers from obtaining
REQ_TYPE_BLOCK_PC type requests which are currently unsupported by
these drivers and which are potentially harmful (as reported by Andrew).
- There is no functionality loss since aforementioned ioctls will now be
handled by idefloppy_ioctl()->scsi_cmd_ioctl() (for devices using
ide-floppy driver) and by idecd_ioctl->cdrom_ioctl()->scsi_cmd_ioctl()
(for devices using ide-cd driver).
Cc: Jens Axboe <jens.axboe@oracle.com> Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Cc: James Bottomley <James.Bottomley@steeleye.com> Cc: Jeff Garzik <jeff@garzik.org> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->host_flags to ide_hwif_t to store ide_pci_device_t.host_flags,
assign it in setup-pci.c:ide_pci_setup_ports().
* Add IDE_HFLAG_PIO_NO_{BLACKLIST,DOWNGRADE} to ide_pci_device_t.host_flags
and teach ide_get_best_pio_mode() about them. Also remove needless
!drive->id check while at it (drive->id is always present).
* Convert amd74xx, via82cxxx and ide-timing.h to use ide_get_best_pio_mode()
and then remove no longer needed ide_find_best_pio_mode().
There should be no functionality changes caused by this patch.
* Some devices claim maximum PIO mode > 2 in id->tPIO, they were punished too
severly for this by being limited to PIO_SLOW. Limit them to PIO2 instead.
v2:
* Fix PIO number being returned incorrectly instead of PIO mode
(Noticed by Sergei).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use it in ali14xx/ht6560b/qd65xx/cmd64{0,x}/sl82c105 and pmac host drivers
(previously cycle time given by the device was only used for "pio" == 255).
* Remove no longer needed ide_pio_data_t.cycle_time field.
v2:
* Fix "ata_" prefix (Noticed by Jeff).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Nowadays core IDE code handles restoring of PIO and DMA modes
(ide-io.c:ide_start_power_step() etc) so remove open-coded version
from sc1200_resume().
There should be no change in behavior because settings done by
sc1200_resume() were always overridden by generic_ide_resume()
and ide_{start,stop}_power_step().
* Bump driver version.
Cc: Mark Lord <mlord@pobox.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Do the same thing as probe_hwif() and always disable DMA so chipset DMA
enabled bit gets cleared (if the drive doesn't support DMA ide_set_dma()
won't try to tune it anyway).
* Add TODO comment about respecting ->using_dma setting.
The driver used to depend on BIOS settings for deciding whether it is OK
to use DMA. However it seems that BIOS doesn't always handle all cases
correctly so just let IDE core to decide about this. It should be a safe
thing to do now, after the driver went through heavy bugfixing.
Thanks for bugreport and testing the patch goes out to Sven Niedner.
* Always set ->autotune so PIO gets correctly auto-tuned (previously
->autotune was only set when ->dma_base wasn't available, however
->ide_dma_check()/->speedproc() was always trying to tune PIO when
tuning DMA).
* Move code responsible for programming chipset for PIO mode from
svwks_tune_chipset() to svwks_tune_pio(). Don't tune PIO when tuning
DMA (this is no longer needed since ->autotune is always set now).
* Handle PIO modes early in svwks_tune_chipset() so DMA configuration
registers don't get cleared when programming PIO mode.
* Add sil_tuneproc() wrapper for siimage_tuneproc() which also sets
PIO mode on the device.
* Add missing ide_get_best_pio_mode() call to sil_tuneproc() so
"pio" == 255 (autotune) is handled correctly (previously PIO0 was used)
and "pio" values > 4 && < 255 are filtered to PIO4 (instead of PIO0).
* Add code limiting maximum PIO mode according to the pair device capabilities
to sil_tuneproc().
* Convert users of config_siimage_chipset_for_pio() to use sil_tune_pio() and
sil_tuneproc(). This fixes PIO fallback in siimage_config_drive_for_dma() to
use max PIO mode available instead of PIO4 (config_siimage_chipset_for_pio()
used wrong arguments for ide_get_best_pio_mode() and as a results always
tried to set PIO4).
* Remove no longer needed siimage_taskfile_timing()
and config_siimage_chipset_for_pio().
* Enable ->autotune unconditionally and remove PIO tuning for UDMA/MDMA modes
from siimage_speedproc()
* Bump driver version.
v2:
* Fix issues noticed by Sergei:
- correct pair device check
- trim only taskfile PIO to the slowest of the master/slave
- enable ->autotune unconditionally and remove PIO tuning for UDMA/MDMA modes
from siimage_speedproc()
- add TODO item for IORDY bugs
- minor cleanups
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Split off exisiting atiixp_tuneproc() into atiixp_tune_pio()
and then add setting device PIO mode to atiixp_tuneproc().
* Add missing ide_get_best_pio_mode() call to atiixp_tuneproc() so
"pio" == 255 (autotune) is handled correctly and "pio" values > 4 && < 255
are filtered to PIO4 (previously "pio" == 5 could result in wrong timings
being used and "pio" values > 4 && < 255 in an OOPS).
* Handle PIO modes early in atiixp_speedproc() so save_mdma_mode[]
doesn't get cleared.
* In atiixp_dma_check():
- fix max_mode argument for ide_get_best_pio_mode()
- don't call atiixp_dma_2_pio() so PIO1 doesn't get remapped to PIO0
- use atiixp_tuneproc() instead of atiixp_speedproc()
Alan Cox [Thu, 19 Jul 2007 23:11:54 +0000 (01:11 +0200)]
ide: Stop mapping ROMs
Various old IDE drivers go mapping ROM devices for no apparent reason and
without using the ROM mapping API we now have. They don't actually use
the ROM they map and the new libata drivers are happy without it being
mapped so rather than port them lets just junk it for the next -rc1.
Signed-off-by: Alan Cox <alan@redhat.com> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Andrew Morton <akpm@osdl.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com> Cc: Michael Starvik <starvik@axis.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
SELinux: use SECINITSID_NETMSG instead of SECINITSID_UNLABELED for NetLabel
SELinux: enable dynamic activation/deactivation of NetLabel/SELinux enforcement
Merge branch 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6
* 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6:
[XFS] Fix inode size update before data write in xfs_setattr
[XFS] Allow punching holes to free space when at ENOSPC
[XFS] Implement ->page_mkwrite in XFS.
[FS] Implement block_page_mkwrite.
Manually fix up conflict with Nick's VM fault handling patches in
fs/xfs/linux-2.6/xfs_file.c
Avi Kivity [Thu, 19 Jul 2007 11:30:14 +0000 (14:30 +0300)]
i386: Allow KVM on i386 nonpae
Currently, CONFIG_X86_CMPXCHG64 both enables boot-time checking of
the cmpxchg64b feature and enables compilation of the set_64bit() family.
Since the option is dependent on PAE, and since KVM depends on set_64bit(),
this effectively disables KVM on i386 nopae.
Simplify by removing the config option altogether: the boot check is made
dependent on CONFIG_X86_PAE directly, and the set_64bit() family is exposed
without constraints. It is up to users to check for the feature flag (KVM
does not as virtualiation extensions imply its existence).
Signed-off-by: Avi Kivity <avi@qumranet.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.linux-nfs.org/pub/linux/nfs-2.6:
NFSv4: handle lack of clientaddr in option string
NFSv4: debug print ntohl(status) in nfs client callback xdr code
SUNRPC: Clean up the sillyrename code
NFS: Introduce struct nfs_removeargs+nfs_removeres
NFS: Use dentry->d_time to store the parent directory verifier.
SUNRPC: move bkl locking and xdr proc invocation into a common helper
NFSv4: Fix the nfsv4 readlink reply buffer alignment
NFSv4: Fix the readdir reply buffer alignment
NFSv4: More NFSv4 xdr cleanups
NFSv4: Try to recover from getfh failures in nfs4_xdr_dec_open
NFSv4: 'constify' lookup arguments.
NFSv4: Don't fail nfs4_xdr_dec_open if decode_restorefh() failed
NFSv4: Fix open state recovery
NFSD/SUNRPC: Fix the automatic selection of RPCSEC_GSS
Matthew Wilcox [Thu, 19 Jul 2007 19:09:10 +0000 (13:09 -0600)]
Update .gitignore for arch/i386/boot
With the new setup code, we generate a couple more files
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
[ .. and do the same for x86-64 - Alexey ] Acked-by: Alexey Dobriyan <adobriyan@gmail.com> Acked-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (33 commits)
xtensa: use DATA_DATA in xtensa
powerpc: add missing DATA_DATA to powerpc
cris: use DATA_DATA in cris
kallsyms: remove usage of memmem and _GNU_SOURCE from scripts/kallsyms.c
kbuild: use -fno-optimize-sibling-calls unconditionally
kconfig: reset generated values only if Kconfig and .config agree.
kbuild: fix the warning when running make tags
kconfig: strip 'CONFIG_' automatically in kernel configuration search
kbuild: use POSIX BRE in headers install target
Whitelist references from __dbe_table to .init
modpost white list pattern adjustment
kbuild: do section mismatch check on full vmlinux
kbuild: whitelist references from variables named _timer to .init.text
kbuild: remove hardcoded _logo names from modpost
kbuild: remove hardcoded apic_es7000 from modpost
kbuild: warn about references from .init.text to .exit.text
kbuild: consolidate section checks
kbuild: refactor code in modpost to improve maintainability
kbuild: ignore section mismatch warnings originating from .note section
kbuild: .paravirtprobe section is obsolete, so modpost doesn't need to handle it
...
Merge branch 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6
* 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6: (44 commits)
i2c: Delete the i2c-isa pseudo bus driver
hwmon: refuse to load abituguru driver on non-Abit boards
hwmon: fix Abit Uguru3 driver detection on some motherboards
hwmon/w83627ehf: Be quiet when no chip is found
hwmon/w83627ehf: No need to initialize fan_min
hwmon/w83627ehf: Export the thermal sensor types
hwmon/w83627ehf: Enable VBAT monitoring
hwmon/w83627ehf: Add support for the VID inputs
hwmon/w83627ehf: Fix timing issues
hwmon/w83627ehf: Add error messages for two error cases
hwmon/w83627ehf: Convert to a platform driver
hwmon/w83627ehf: Update the Kconfig entry
make coretemp_device_remove() static
hwmon: Add LM93 support
hwmon: Improve the pwmN_enable documentation
hwmon/smsc47b397: Don't report missing fans as spinning at 82 RPM
hwmon: Add support for newer uGuru's
hwmon/f71805f: Add temperature-tracking fan control mode
hwmon/w83627ehf: Preserve speed reading when changing fan min
hwmon: fix detection of abituguru volt inputs
...
Manual fixup of trivial conflict in MAINTAINERS file
Matt Mackall [Thu, 19 Jul 2007 18:30:14 +0000 (11:30 -0700)]
random: fix bound check ordering (CVE-2007-3105)
If root raised the default wakeup threshold over the size of the
output pool, the pool transfer function could overflow the stack with
RNG bytes, causing a DoS or potential privilege escalation.
(Bug reported by the PaX Team <pageexec@freemail.hu>)
Cc: Theodore Tso <tytso@mit.edu> Cc: Willy Tarreau <w@1wt.eu> Signed-off-by: Matt Mackall <mpm@selenic.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched:
[PATCH] sched: implement cpu_clock(cpu) high-speed time source
[PATCH] sched: fix the all pinned logic in load_balance_newidle()
[PATCH] sched: fix newly idle load balance in case of SMT
[PATCH] sched: sched_cacheflush is now unused
When a CONFIG_USER_NS=n and a user tries to unshare some namespace other
than the user namespace, the dummy copy_user_ns returns NULL rather than
the old_ns.
This value then gets assigned to task->nsproxy->user_ns, so that a
subsequent setuid, which uses task->nsproxy->user_ns, causes a NULL
pointer deref.
Fix this by returning old_ns.
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The slab and slob allocators already did this right, but slub would call
"get_object_page()" on the magic ZERO_SIZE_PTR, with all kinds of nasty
end results.
Noted by Ingo Molnar.
Cc: Ingo Molnar <mingo@elte.hu> Cc: Christoph Lameter <clameter@sgi.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix up non-NUMA SLAB configuration for zero-sized allocations
I suspect Christoph tested his code only in the NUMA configuration, for
the combination of SLAB+non-NUMA the zero-sized kmalloc's would not work.
Of course, this would only trigger in configurations where those zero-
sized allocations happen (not very common), so that may explain why it
wasn't more widely noticed.
Seen by by Andi Kleen under qemu, and there seems to be a report by
Michael Tsirkin on it too.
Cc: Andi Kleen <ak@suse.de> Cc: Roland Dreier <rdreier@cisco.com> Cc: Michael S. Tsirkin <mst@dev.mellanox.co.il> Cc: Pekka Enberg <penberg@cs.helsinki.fi> Cc: Christoph Lameter <clameter@sgi.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[PATCH] sched: fix newly idle load balance in case of SMT
In the presence of SMT, newly idle balance was never happening for
multi-core and SMP domains (even when both the logical siblings are
idle).
If thread 0 is already idle and when thread 1 is about to go to idle,
newly idle load balance always think that one of the threads is not idle
and skips doing the newly idle load balance for multi-core and SMP
domains.
This is because of the idle_cpu() macro, which checks if the current
process on a cpu is an idle process. But this is not the case for the
thread doing the load_balance_newidle().
Fix this by using runqueue's nr_running field instead of idle_cpu(). And
also skip the logic of 'only one idle cpu in the group will be doing
load balancing' during newly idle case.
Jeff Layton [Wed, 18 Jul 2007 15:28:43 +0000 (11:28 -0400)]
NFSv4: handle lack of clientaddr in option string
If a NFSv4 mount is attempted with string based options, and the
option string doesn't contain a clientaddr= option, the kernel will
currently oops. Check for this situation and return a proper error.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Fix a couple of bugs:
- Don't rely on the parent dentry still being valid when the call completes.
Fixes a race with shrink_dcache_for_umount_subtree()
- Don't remove the file if the filehandle has been labelled as stale.
Fix a couple of inefficiencies
- Remove the global list of sillyrenamed files. Instead we can cache the
sillyrename information in the dentry->d_fsdata
- Move common code from unlink_setup/unlink_done into fs/nfs/unlink.c
J. Bruce Fields [Wed, 11 Jul 2007 22:39:02 +0000 (18:39 -0400)]
SUNRPC: move bkl locking and xdr proc invocation into a common helper
Since every invocation of xdr encode or decode functions takes the BKL now,
there's a lot of redundant lock_kernel/unlock_kernel pairs that we can pull
out into a common function.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
projects / linux-2.6 / log