Andi Kleen [Tue, 4 Oct 2005 22:21:39 +0000 (00:21 +0200)]
[PATCH] x86_64: Drop global bit from early low mappings
Drop global bit from early low mappings
Suggested by Linus, originally also proposed by Suresh.
This fixes a race condition with early start of udev, originally
tracked down by Suresh B. Siddha. The problem was that switching
to the user space VM would not clear the global low mappings
for the beginning of memory, which lead to memory corruption.
Drop the global bits.
The kernel mapping stays global because it should stay constant.
Sascha Hauer [Tue, 4 Oct 2005 22:17:52 +0000 (23:17 +0100)]
[ARM] 2950/1: i.MX gpio setup function
Patch from Sascha Hauer
Current implementation of imx_gpio_mode does not allow to
configure all alternate routing possibilities of the i.MX. With
this patch every bit in the gpio setup registers has a
corresponding bit in the gpio_mode parameter, so every routing
should be possible now.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allan Graves [Tue, 4 Oct 2005 18:53:52 +0000 (14:53 -0400)]
[PATCH] uml: Fix sysrq-r support for skas mode
The old code had the IP and SP coming from the registers in the thread
struct, which are completely wrong since those are the userspace
registers. This fixes that by pulling the correct values from the
jmp_buf in which the kernel state of each thread is stored.
Signed-off-by: Allan Graves <allan.graves@oracle.com> Signed-off-by: Jeff Dike <jdike@addtoit.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Al Viro [Tue, 4 Oct 2005 16:48:44 +0000 (17:48 +0100)]
[PATCH] bfs iget() abuses
bfs_fill_super() walks the inode table to get the bitmap of free inodes
and collect stats. It has no business using iget() for that - it's a
lot of extra work, extra icache pollution and more complex code.
Switched to walking the damn thing directly.
Note: that also allows to kill ->i_dsk_ino in there - separate patch if
Tigran can confirm that this field can be zero only for deleted inodes
(i.e. something that could only be found during that scan and not by
normal lookups).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Robert Olsson [Tue, 4 Oct 2005 20:01:58 +0000 (13:01 -0700)]
[IPV4]: fib_trie root-node expansion
The patch below introduces special thresholds to keep root node in the trie
large. This gives a flatter tree at the cost of a modest memory increase.
Overall it seems to be gain and this was also proposed by one the authors
of the paper in recent a seminar.
Main table after loading 123 k routes.
Aver depth: 3.30
Max depth: 9
Root-node size 12 bits
Total size: 4044 kB
With the patch:
Aver depth: 2.78
Max depth: 8
Root-node size 15 bits
Total size: 4150 kB
An increase of 8-10% was seen in forwading performance for an rDoS attack.
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se> Signed-off-by: David S. Miller <davem@davemloft.net>
NTFS: Fix a 64-bitness bug where a left-shift could overflow a 32-bit variable
which we now cast to 64-bit first (fs/ntfs/mft.c::map_mft_record_page().
Signed-off-by: Anton Altaparmakov <aia21@cantab.net>
NTFS: Fix a stupid bug in __ntfs_bitmap_set_bits_in_run() which caused the
count to become negative and hence we had a wild memset() scribbling
all over the system's ram.
Signed-off-by: Anton Altaparmakov <aia21@cantab.net>
Ion Badulescu [Tue, 4 Oct 2005 02:31:36 +0000 (22:31 -0400)]
[netdrvr starfire] fix highmem and broken firmware issues
Unfortunately, [your patch] might address the crash but doesn't address
the real problem. It turns out that the problem is one of padding
(the firmware cksum engine works only on 32-bit chunks, yuck), so
the special casing for length == 1 wasn't sufficient anyway.
This patch addresses the issue, as well the other issue of i386 +
CONFIG_HIGHMEM being broken. It is pretty much the same workaround
that Adaptec themselves used in their Windows driver. I have yet to
check if it fixes the problem when the skb is non-linear, but this
patch _will_ solve the problem for 99% of the users out there (those
not using sendfile).
Signed-off-by: Ion Badulescu <ionut@badula.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The patch below is necessary to allow my Digital DS21143 Tulip rev 48
ethernet interface to work in a 10Mbit Half Duplex network. Without
it, the driver keeps retrying other modes in an endless loop. It seems
like someone already had the same problem with a rev 65 board :)
Signed-off-by: Philippe De Muyter <phdm@macqel.be> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
From: Peter Tiedemann <ptiedem@de.ibm.com>
From: Frank Pavlic <pavlic@de.ibm.com>
minor qeth fixes:
- free old skb in qeth_realloc_headroom after duplicating skb
- disable IPV6 support for Hipersockets devices
- call ccw_device_set_offline on every channel regardless
of the return value of the prior ccw_device_set_offline calls
- allocate qdio structures in DMA-area
- schedule recovery of appropriate card
when cable has been inserted again.
- add missing initialization of card->lock
- write sequence number in skb->cb for SNA protocol which
requires strictly serialized packets.
Herbert Xu [Mon, 3 Oct 2005 21:35:55 +0000 (14:35 -0700)]
[IPV4]: Replace __in_dev_get with __in_dev_get_rcu/rtnl
The following patch renames __in_dev_get() to __in_dev_get_rtnl() and
introduces __in_dev_get_rcu() to cover the second case.
1) RCU with refcnt should use in_dev_get().
2) RCU without refcnt should use __in_dev_get_rcu().
3) All others must hold RTNL and use __in_dev_get_rtnl().
There is one exception in net/ipv4/route.c which is in fact a pre-existing
race condition. I've marked it as such so that we remember to fix it.
This patch is based on suggestions and prior work by Suzanne Wood and
Paul McKenney.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Mon, 3 Oct 2005 21:18:10 +0000 (14:18 -0700)]
[IPV4]: Fix "Proxy ARP seems broken"
Meelis Roos <mroos@linux.ee> wrote:
> RK> My firewall setup relies on proxyarp working. However, with 2.6.14-rc3,
> RK> it appears to be completely broken. The firewall is 212.18.232.186,
>
> Same here with some kernel between 14-rc2 and 14-rc3 - no reposnse to
> ARP on a proxyarp gateway. Sorry, no exact revison and no more debugging
> yet since it'a a production gateway.
The breakage is caused by the change to use the CB area for flagging
whether a packet has been queued due to proxy_delay. This area gets
cleared every time arp_rcv gets called. Unfortunately packets delayed
due to proxy_delay also go through arp_rcv when they are reprocessed.
In fact, I can't think of a reason why delayed proxy packets should go
through netfilter again at all. So the easiest solution is to bypass
that and go straight to arp_process.
This is essentially what would've happened before netfilter support
was added to ARP.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
During the build for ARM machine type "fortunet", this error occurred:
CC net/sysctl_net.o
net/sysctl_net.c:36: error: 'core_table' undeclared here (not in a function)
It appears that the following configuration settings cause this error
due to a missing include:
CONFIG_SYSCTL=y
CONFIG_NET=y
# CONFIG_INET is not set
core_table appears to be declared in net/sock.h. if CONFIG_INET were
defined, net/sock.h would have been included via:
sysctl_net.c -> net/ip.h -> linux/ip.h -> net/sock.h
so include it directly.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 3 Oct 2005 21:13:38 +0000 (14:13 -0700)]
[INET]: speedup inet (tcp/dccp) lookups
Arnaldo and I agreed it could be applied now, because I have other
pending patches depending on this one (Thank you Arnaldo)
(The other important patch moves skc_refcnt in a separate cache line,
so that the SMP/NUMA performance doesnt suffer from cache line ping pongs)
1) First some performance data :
--------------------------------
tcp_v4_rcv() wastes a *lot* of time in __inet_lookup_established()
The most time critical code is :
sk_for_each(sk, node, &head->chain) {
if (INET_MATCH(sk, acookie, saddr, daddr, ports, dif))
goto hit; /* You sunk my battleship! */
}
The sk_for_each() does use prefetch() hints but only the begining of
"struct sock" is prefetched.
As INET_MATCH first comparison uses inet_sk(__sk)->daddr, wich is far
away from the begining of "struct sock", it has to bring into CPU
cache cold cache line. Each iteration has to use at least 2 cache
lines.
This can be problematic if some chains are very long.
2) The goal
-----------
The idea I had is to change things so that INET_MATCH() may return
FALSE in 99% of cases only using the data already in the CPU cache,
using one cache line per iteration.
3) Description of the patch
---------------------------
Adds a new 'unsigned int skc_hash' field in 'struct sock_common',
filling a 32 bits hole on 64 bits platform.
struct sock_common {
unsigned short skc_family;
volatile unsigned char skc_state;
unsigned char skc_reuse;
int skc_bound_dev_if;
struct hlist_node skc_node;
struct hlist_node skc_bind_node;
atomic_t skc_refcnt;
+ unsigned int skc_hash;
struct proto *skc_prot;
};
Store in this 32 bits field the full hash, not masked by (ehash_size -
1) Using this full hash as the first comparison done in INET_MATCH
permits us immediatly skip the element without touching a second cache
line in case of a miss.
Suppress the sk_hashent/tw_hashent fields since skc_hash (aliased to
sk_hash and tw_hash) already contains the slot number if we mask with
(ehash_size - 1)
- Adds a prefetch(head->chain.first) in
__inet_lookup_established()/__tcp_v4_check_established() and
__inet6_lookup_established()/__tcp_v6_check_established() and
__dccp_v4_check_established() to bring into cache the first element of the
list, before the {read|write}_lock(&head->lock);
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Acked-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 3 Oct 2005 21:02:39 +0000 (14:02 -0700)]
[TG3]: Refine AMD K8 write-reorder chipset test.
Test for VIA K8T800 north bridge instead of AMD K8 HyperTransport
bridge based on new information from Andi Kleen. The AMD
HyperTransport interface is not responsible for PCI transactions
and so the re-ordering is more likely done by the VIA north bridge.
This code is subject to change if we get more information from AMD
or VIA.
PCI Express devices are excluded from doing the read flush since all
chipsets in the write_reorder list are PCI chipsets.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Mon, 3 Oct 2005 20:57:23 +0000 (13:57 -0700)]
[NET]: Fix packet timestamping.
I've found the problem in general. It affects any 64-bit
architecture. The problem occurs when you change the system time.
Suppose that when you boot your system clock is forward by a day.
This gets recorded down in skb_tv_base. You then wind the clock back
by a day. From that point onwards the offset will be negative which
essentially overflows the 32-bit variables they're stored in.
In fact, why don't we just store the real time stamp in those 32-bit
variables? After all, we're not going to overflow for quite a while
yet.
When we do overflow, we'll need a better solution of course.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
[PATCH] x86_64: Fix numa node topology detection for srat based x86_64 boxes
2.6.14-rc2 does not assign cpus to proper nodeids on our em64t numa boxen.
Our boxes use acpi srat for parsing the numa information.
srat_detect_node() used phys_proc_id[] to get to the cpu's local apic id,
but phys_proc_id[] represents the cpu<->initial_apic_id mapping. The
following patch fixes this problem. Now apicid_to_node[] is properly
indexed with the local apic id.
James Bottomley [Sat, 1 Oct 2005 14:38:05 +0000 (09:38 -0500)]
[SCSI] Legacy MegaRAID: Fix READ CAPACITY
Some Legacy megaraid cards can't actually cope with the scatter/gather
version of the READ CAPACITY command (which is what we now send them
since altering all SCSI internal I/O to go via the block layer). Fix
this (and a few other broken megaraid driver assumptions) by sending
the non-sg version of the command if the sg list only has a single
element.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Catalin Marinas [Sun, 2 Oct 2005 21:34:35 +0000 (22:34 +0100)]
[ARM] 2943/1: Clear the exclusive monitor in v6_early_abort
Patch from Catalin Marinas
Data abort caused by ldrex/strex can leave the exclusive monitor in an
unpredictable state. It is recommended that a clrex/strex is performed to
clear this state.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
James Bottomley [Sun, 2 Oct 2005 20:22:35 +0000 (15:22 -0500)]
[SCSI] aic7xxx/aic79xx: fix module removal path not to panic
In these drivers, scsi_remove_host() is called too late, at the point
it is called, the driver has already shut down too far to accept any
I/O that the shutdown might generate. Any generated I/O actually
triggers a panic.
Fix this by calling scsi_remove_host() as early as possible and not
calling scsi_host_put() until just before we kfree the ahc_softc.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Bottomley [Sun, 2 Oct 2005 17:59:49 +0000 (12:59 -0500)]
[SCSI] fix potential panic with proc on module removal
There's a problem in our host release in that it calls
scsi_proc_hostdir_rm(). However, if you hold a reference to the host as
you remove the module, the host template (which proc uses) will be freed
and the system will panic when the host device is finally released.
Fix this by moving scsi_proc_hostdir_rm() to where it should be: in
scsi_remove_host().
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Russell King [Sun, 2 Oct 2005 17:12:03 +0000 (18:12 +0100)]
[ARM] Fix init printk for EBSA110 network driver, and link timer
Arrange for the initialisation printks to happen after we've
registered the network interface, so we know what name the
device is. Also, check the link every 500ms (and use
msecs_to_jiffies.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Sven Henkel [Sat, 1 Oct 2005 22:30:33 +0000 (08:30 +1000)]
[PATCH] ppc32: Add new iBook 12" to PowerMac models table
This adds the new iBook G4 (manufactured after July 2005) to the
PowerMac models table. The model name (PowerBook6,7) is taken from a
12" iBook, I don't know if it also matches the 14" version. The patch
applies to a vanilla 2.6.13.2 kernel.
Signed-off-by: Sven Henkel <shenkel@gmail.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sven Henkel [Sat, 1 Oct 2005 22:29:18 +0000 (08:29 +1000)]
[PATCH] pmac/radeonfb: Add suspend support for M11 chip in new iBook 12"
This adds suspend support for the Radeon M11 chip in 12" iBooks
manufactured after July 2005. I don't know if the new 14" iBooks also
have that chip, so they might also be supported.
The chip identifies itself as "RV350 NV" (pci id 0x4e56), revision 0x80.
Apple calls it "Snowy", xfree86 names it "ATI FireGL Mobility T2 (M11)
NV (AGP)". So, we seem to be lucky here: The suspend-code for the M10
(which also is a "RV350 NV") works flawless for that chip.
Signed-off-by: Sven Henkel <shenkel@gmail.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Linus Torvalds [Sat, 1 Oct 2005 18:04:18 +0000 (11:04 -0700)]
Fix inequality comparison against "task->state"
We should always use bitmask ops, rather than depend on some ordering of
the different states. With the TASK_NONINTERACTIVE flag, the inequality
doesn't really work.
Oleg Nesterov argues (likely correctly) that this test is unnecessary in
the first place. However, the minimal fix for now is to at least make
it work in the presense of TASK_NONINTERACTIVE. Waiting for consensus
from Roland & co on potential bigger cleanups.
[PATCH] ARM: Fix IXP2000 serial port resource range. For real this time.
Serial port only needs 32 bytes of resource space but we are currently
asking for 64K.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
[ diff went missing first time due to corrupted patch ] Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As an alternative, people can use the boot time 'debug' option and/or use
'ethtool -s ethX msglvl xyz'. The different messages are listed at:
http://www.zoreil.com/~romieu/r8169/doc/msglvl.txt
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Cc: Jeff Garzik <jgarzik@pobox.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The old 550Mhz titanium powerbook can switch to a lower frequency
(500Mhz). A user has been repeately reporting overtemp conditions on his
machine at high speed so this simple patch adds support to PowerMac
cpufreq for this machine. The difference in frequency isn't big but seem
enough to fix that user's problems. The patch has been around for some
time now and doesn't seem to cause any problem, so I suppose it could go
in now.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Alain RICHARD <alain.richard@equation.fr> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The tests Alok carried out on Petr's box confirmed that cpu_to_node[BP] is
not setup early enough by numa_init_array due to the x86_64 changes in
2.6.14-rc*, and unfortunately set wrongly by the work around code in
numa_init_array(). cpu_to_node[0] gets set with 1 early and later gets set
properly to 0 during identify_cpu() when all cpus are brought up, but
confusing the numa slab in the process.
Here is a quick fix for this. The right fix obviously is to have
cpu_to_node[bsp] setup early for numa_init_array(). The following patch
will fix the problem now, and the code can stay on even when
cpu_to_node{BP] gets fixed early correctly.
Thanks to Petr for access to his box.
Signed off by: Ravikiran Thirumalai <kiran@scalex86.org> Signed-off-by: Alok N Kataria <alokk@calsoftinc.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the BP node_to_cpumask. 2.6.14-rc* broke the boot cpu bit as the
cpu_to_node(0) is now not setup early enough for numa_init_array.
cpu_to_node[] is setup much later at srat_detect_node on acpi srat based
em64t machines. This seems like a problem on amd machines too, Tested on
em64t though. /sys/devices/system/node/node0/cpumap shows up sanely after
this patch.
Signed off by: Ravikiran Thirumalai <kiran@scalex86.org> Signed-off-by: Shai Fultheim <shai@scalex86.org> Cc: Andi Kleen <ak@muc.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] utilization of kprobe_mutex is incorrect on x86_64
The up()/down() orders are incorrect in arch/x86_64/kprobes.c file.
kprobe_mutext is used to protect the free kprobe instruction slot list.
arch_prepare_kprobe applies for a slot from the free list, and
arch_remove_kprobe returns a slot to the free list. The incorrect up()/down()
orders to operate on kprobe_mutex fail to protect the free list. If 2 threads
try to get/return kprobe instruction slot at the same time, the free slot list
might be broken, or a free slot might be applied by 2 threads.
[PATCH] eth1394: workaround limitation in rawiso routines
Work around limitation in rawiso routines. Required with 1394b cards on
architectures where PAGE_SIZE is 4096. Based on a previous patch by Ben
Collins.
Signed-off-by: Jody McIntyre <scjody@steamballoon.com> Cc: Ben Collins <bcollins@debian.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] ieee1394: skip unnecessary pause when scanning config ROMs
Skip a superfluous pause that occured when the config ROM of a node was
scanned unsuccessfully. This also occurs if a node without link wrongly
enables its "link active" self ID flag. A GWCTech 6-port hub does this.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Jody McIntyre <scjody@steamballoon.com> Cc: Ben Collins <bcollins@debian.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] ieee1394: reorder activities after bus reset (fixes device detection)
Units were not detected if the local IRM performed a bus reset. ("The root
node is not cycle master capable; selecting a new root node and resetting...",
often seen with iPods and other SBP-2 devices). Rearrange the order of IRM
duties and node scanning. TODO: Audit the ROM caching and parsing code for
underlying issues.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Jody McIntyre <scjody@steamballoon.com> Cc: Ben Collins <bcollins@debian.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Set serialize_io=1 by default. This is safer and required by seemingly more
and more hardware. It causes little or no performance loss for S400 devices.
Performance of S800 1394b devices may drop by 25...30%. Therefore make the
parameter's description and dmesg message clearer about performance impact.
Update description of the max_speed parameter too. IEEE1394_SPEED_MAX is
currently S800.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Jody McIntyre <scjody@steamballoon.com> Cc: Ben Collins <bcollins@debian.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] sbp2: fix deadlocks and delays on device removal/rmmod
Fixes for deadlocks of the ieee1394 and scsi subsystems and long delays in
futile error recovery attempts when SBP-2 devices are removed or drivers are
unloaded.
- Complete commands quickly with DID_NO_CONNECT if the 1394 node is gone or if
the 1394 low-level driver was unloaded.
- Skip unnecessary work in the eh_abort_handler and eh_device_reset_handler if
the node or 1394 low-level driver is gone.
- Let scsi's high-level shut down gracefully when sbp2 is being unloaded or
detached from the 1394 unit. A call to scsi_remove_device is added for this
purpose, which requires us to store a scsi_device pointer.
- scsi_device pointer is obtained from slave_alloc hook and cleared by
slave_destroy. This avoids usage of the pointer after the scsi device was
deleted e.g. by the user via scsi_mod's sysfs interface.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Jody McIntyre <scjody@steamballoon.com> Cc: Ben Collins <bcollins@debian.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This change removes a bogus error message from the IOC4 serial driver
interrupt handler.
This error message is bogus for two reasons. First, it can never occur
given that current code takes care to initialize IOC4 in such a way that
these "unknown" interrupts could never occur. Second, this code fails to
take into account that other drivers can share the IOC4 interrupt mechanism
through SA_SHIRQ, and thus this driver is not in-fact "all-knowing".
Finally, this error message triggers every time some "unknown" interrupt
occurs -- it's not rate limited or repetition limited in any way, thereby
effectively denying use of the console device. Given its bogosity in the
first place, it's best to just get rid of it entirely.
Acked-by: Pat Gefre <pfg@sgi.com> Signed-off-by: Brent Casavant <bcasavan@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Check O_DIRECT and return -EINVAL error in open. dentry_open() also checks
this but only after the open method is called. This patch optimizes away
the unnecessary upcalls in this case.
It could be a correctness issue too: if filesystem has open() with side
effect, then it should fail before doing the open, not after.
Calling truncate() on hostfs spits a kernel warning "Something isn't
implemented here", but it still works fine.
Indeed, hostfs i_op->truncate doesn't do anything. But hostfs_setattr() ->
set_attr() correctly detects ATTR_SIZE and calls truncate() on the host. So
we should be safe (using ftruncate() may be better, in case the file is
unlinked on the host, but we aren't sure to have the file open for writing,
and reopening it would cause the same races; plus nobody should expect UML to
be so careful).
So, the warning is wrong, because the current implementation is working. Al,
am I correct, and can the warning be therefore dropped?
CC: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
a) sysrq may be run when the scheduler is non-functioning
b) the warning I wanted to fix actually came from the fault handler run in
atomic context. But I fixed that not to take the semaphore in a separate
patch.
c) the fault handler is run because of a fault, and that fault was
unaffected by this patch.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] uml: clear SKAS0/3 flags when running in TT mode
SEGV_MAYBE_FIXABLE tests ptrace_faultinfo, and depends on it being 1 only in
SKAS3 mode, while currently when running with mode=tt it will be 1 anyway.
Fix this, and do the same for proc_mm.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I hadn't been running a SKAS3 host when testing the "uml: fix hang in TT mode
on fault" patch (commit 546fe1cbf91d4d62e3849517c31a2327c992e5c5), and I
didn't think enough to the missing trap_no in SKAS3 mode.
In fact, the resulting kernel doesn't work at all in SKAS3 mode.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Michael Krufky [Fri, 30 Sep 2005 18:58:58 +0000 (11:58 -0700)]
[PATCH] v4l: DViCO FusionHDTV5 Lite GPIO Fix
GPIO fix for the composite and tv mute states of bt8xx card #135: DViCO
FusionHDTV5 Lite. Without this patch, selecting one of these states could
produce unexpected behavior.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Morton [Fri, 30 Sep 2005 18:58:57 +0000 (11:58 -0700)]
[PATCH] x86: hw_irq.h warning fix
include/asm/hw_irq.h:70: warning: `struct hw_interrupt_type' declared inside parameter list
include/asm/hw_irq.h:70: warning: its scope is only this definition or declaration, which is probably not what you want
Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Zach Brown [Fri, 30 Sep 2005 18:58:56 +0000 (11:58 -0700)]
[PATCH] aio: avoid extra aio_{read,write} call when ki_left == 0
Recently aio_p{read,write} changed to perform retries internally rather
than returning -EIOCBRETRY. This inadvertantly resulted in always calling
aio_{read,write} with ki_left at 0 which would in turn immediately return
0. Harmless, but we can avoid this call by checking in the caller.
Signed-off-by: Zach Brown <zach.brown@oracle.com> Signed-off-by: Benjamin LaHaise <bcrl@linux.intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Zach Brown [Fri, 30 Sep 2005 18:58:55 +0000 (11:58 -0700)]
[PATCH] aio: remove unlocked task_list test and resulting race
Only one of the run or kick path is supposed to put an iocb on the run
list. If both of them do it than one of them can end up referencing a
freed iocb. The kick path could delete the task_list item from the wait
queue before getting the ctx_lock and putting the iocb on the run list.
The run path was testing the task_list item outside the lock so that it
could catch ki_retry methods that return -EIOCBRETRY *without* putting the
iocb on a wait queue and promising to call kick_iocb. This unlocked check
could then race with the kick path to cause both to try and put the iocb on
the run list.
The patch stops the run path from testing task_list by requring that any
ki_retry that returns -EIOCBRETRY *must* guarantee that kick_iocb() will be
called in the future. aio_p{read,write}, the only in-tree -EIOCBRETRY
users, are updated.
Signed-off-by: Zach Brown <zach.brown@oracle.com> Signed-off-by: Benjamin LaHaise <bcrl@linux.intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Zach Brown [Fri, 30 Sep 2005 18:58:54 +0000 (11:58 -0700)]
[PATCH] aio: lock around kiocbTryKick()
Only one of the run or kick path is supposed to put an iocb on the run
list. If both of them do it than one of them can end up referencing a
freed iocb. The kick patch could set the Kicked bit before acquiring the
ctx_lock and putting the iocb on the run list. The run path, while holding
the ctx_lock, could see this partial kick and mistake it for a kick that
was deferred while it was doing work with the run_list NULLed out. It
would then race with the kick thread to add the iocb to the run list.
This patch moves the kick setting under the ctx_lock so that only one of
the kick or run path queues the iocb on the run list, as intended.
Signed-off-by: Zach Brown <zach.brown@oracle.com> Signed-off-by: Benjamin LaHaise <bcrl@linux.intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
projects / linux-2.6 / log