Wang Chen [Tue, 15 Jul 2008 03:57:07 +0000 (20:57 -0700)]
macvlan: Check return of dev_set_allmulti
allmulti might overflow.
Commit: "netdevice: Fix promiscuity and allmulti overflow" in net-next makes
dev_set_promiscuity/allmulti return error number if overflow happened.
Here, we check the positive increment for allmulti to get error return.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Tue, 15 Jul 2008 03:56:34 +0000 (20:56 -0700)]
ipv4: Fix ipmr unregister device oops
An oops happens during device unregister.
The following oops happened when I add two tunnels, which
use a same device, and then delete one tunnel.
Obviously deleting tunnel "A" causes device unregister, which
send a notification, and after receiving notification, ipmr do
unregister again for tunnel "B" which also use same device.
That is wrong.
After receiving notification, ipmr only needs to decrease reference
count and don't do duplicated unregister.
Fortunately, IPv6 side doesn't add tunnel in ip6mr, so it's clean.
This patch fixs:
- unregister device oops
- using after dev_put()
Wang Chen [Tue, 15 Jul 2008 03:55:26 +0000 (20:55 -0700)]
ipv4: Check return of dev_set_allmulti
allmulti might overflow.
Commit: "netdevice: Fix promiscuity and allmulti overflow" in net-next makes
dev_set_promiscuity/allmulti return error number if overflow happened.
Here, we check the positive increment for allmulti to get error return.
PS: For unwinding tunnel creating, we let ipip->ioctl() to handle it.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Tue, 15 Jul 2008 03:54:23 +0000 (20:54 -0700)]
ipv6: Check return of dev_set_allmulti
allmulti might overflow.
Commit: "netdevice: Fix promiscuity and allmulti overflow" in net-next makes
dev_set_promiscuity/allmulti return error number if overflow happened.
Here, we check the positive increment for allmulti to get error return.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Tue, 15 Jul 2008 03:53:13 +0000 (20:53 -0700)]
bridge: Check return of dev_set_promiscuity
dev_set_promiscuity/allmulti might overflow.
Commit: "netdevice: Fix promiscuity and allmulti overflow" in net-next makes
dev_set_promiscuity/allmulti return error number if overflow happened.
Here, we check the positive increment for promiscuity to get error return.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Tue, 15 Jul 2008 03:51:36 +0000 (20:51 -0700)]
bonding: Check return of dev_set_promiscuity/allmulti
dev_set_promiscuity/allmulti might overflow.
Commit: "netdevice: Fix promiscuity and allmulti overflow" in net-next makes
dev_set_promiscuity/allmulti return error number if overflow happened.
In bond_alb and bond_main, we check all positive increment for promiscuity
and allmulti to get error return.
But there are still two problems left.
1. Some code path has no mechanism to signal errors upstream.
2. If there are multi slaves, it's hard to tell which slaves increment
promisc/allmulti successfully and which failed.
So I left these problems to be FIXME.
Fortunately, the overflow is very rare case.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Tue, 15 Jul 2008 03:49:46 +0000 (20:49 -0700)]
af_packet: Check return of dev_set_promiscuity/allmulti
dev_set_promiscuity/allmulti might overflow. Commit: "netdevice: Fix
promiscuity and allmulti overflow" in net-next makes
dev_set_promiscuity/allmulti return error number if overflow happened.
In af_packet, we check all positive increment for promiscuity and
allmulti to get error return.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
iwlwifi: make index unsigned int for iwl_send_led_cmd
This is a small fix to change the idx type from int to unsigned.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zhu Yi [Fri, 11 Jul 2008 03:53:40 +0000 (11:53 +0800)]
iwlwifi: send TXPOWER command after a new RXON command
The patch fixes the problem that TXPOWER command is not sent
after we issue a new RXON command which requires a tune. Otherwise
we won't be able to Tx any frames.
Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 11 Jul 2008 03:53:39 +0000 (11:53 +0800)]
iwlwifi: enable active scanning
This patch enables active scan on active channels.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 11 Jul 2008 03:53:38 +0000 (11:53 +0800)]
iwlwifi: unify 4965 and 5000 scanning code
This patch unifies 4965 and 5000 scanning code.
We increases the version number to 1.3.27. Since new uCode
iwlwifi-4965-2.ucode is required for 4965 cards.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 11 Jul 2008 03:53:37 +0000 (11:53 +0800)]
iwlwifi: LED use correctly blink table
This patch makes correct usage of the LED blink table.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 11 Jul 2008 03:53:36 +0000 (11:53 +0800)]
iwlwifi: fix LED stall
This patch fixes LED stall. last_blink_time was updated only if LED command
was sent, causing wrong computation of the througput.
Some code cleanup comes with this patch as well
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 11 Jul 2008 03:53:35 +0000 (11:53 +0800)]
iwlwifi: differentiate 4965 and 5000 hw ampdu queues number
This patch asks to allocate the correct amount of sw queues according
to hw ampdu queues number.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi: make iwl4965_mac_conf_tx in atomic context
This patch fixes iwl4965_mac_conf_tx. A mutex was taken in atomic context
leading to Oops. This patch removes the mutex and extends the hold
priv->lock. None of the field of QOS is accessed without priv->lock held.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 11 Jul 2008 03:53:33 +0000 (11:53 +0800)]
iwlwifi: rs always set lq_sta->priv
This patch fixes printk NULL pointer exceptions in rs code.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Guy Cohen <guy.cohen@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 11 Jul 2008 03:53:32 +0000 (11:53 +0800)]
iwlwifi: remove post associate work
This patch removes post associate work. It wasn't used.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the RTS / CTS support in iwlwifi. 5000 will send CTS to
self when allowed by spec, 4965 will send RTS or CTS to self according to
mac80211 request.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Esti Kummer [Fri, 11 Jul 2008 03:53:30 +0000 (11:53 +0800)]
iwlwifi: adding pci device ids to iwl_hw_card_ids
The patch adds PCI device IDs to iwl_hw_card_ids.
Signed-off-by: Esti Kummer <stkumer@localhost.localdomain> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: dont add a STA which is not in the same IBSS
This patch avoids adding STAs that don't belong to our IBSS
ieee80211_bssid_match matches also bcast address so also APs
were added
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 10 Jul 2008 09:22:31 +0000 (11:22 +0200)]
mac80211: fix struct ieee80211_tx_queue_params
Multiple issues:
- there are no "default" values needed
- cw_min/cw_max can be larger than documented
- restructure to decrease size
- use get_unaligned_le16
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 10 Jul 2008 09:21:26 +0000 (11:21 +0200)]
mac80211: fix TX sequence numbers
This patch makes mac80211 assign proper sequence numbers to
QoS-data frames. It also removes the old sequence number code
because we noticed that only the driver or hardware can assign
sequence numbers to non-QoS-data and especially management
frames in a race-free manner because beacons aren't passed
through mac80211's TX path.
This patch also adds temporary code to the rt2x00 drivers to
not break them completely, that code will have to be reworked
for proper sequence numbers on beacons.
It also moves sequence number assignment down in the TX path
so no sequence numbers are assigned to frames that are dropped.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 10 Jul 2008 09:16:47 +0000 (11:16 +0200)]
wext: make sysfs bits optional and deprecate them
The /sys/class/net/*/wireless/ direcory is, as far as I know, not
used by anyone. Additionally, the same data is available via wext
ioctls. Hence the sysfs files are pretty much useless. This patch
makes them optional and schedules them for removal.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: Jean Tourrilhes <jt@hpl.hp.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the check at the entrance to ieee80211_rx_reorder_ampdu.
This check has been broken by 'mac80211: rx.c use new helpers'.
Letting QoS NULL packet in ieee80211_rx_reorder_ampdu led to packet loss in
RX.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rtl8187: use different ANAPARAM*_OFF values for 8187B
For RTL8187B it seems we need special values too for ANAPARAM*_OFF
values (and not use RTL8187 ones). The ANAPARAM*_OFF values used are the
stock ones read from the hardware after a cold boot.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Wed, 9 Jul 2008 13:48:45 +0000 (15:48 +0200)]
ssb: Include dma-mapping.h
ssb.h implements DMA mapping functions, so it should
include dma-mapping.h. This fixes compile failures on certain architectures.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Wed, 9 Jul 2008 13:12:44 +0000 (15:12 +0200)]
rt2x00: Reorganize beacon handling
With the new beacon handling from mac80211 we can
reorganize the beacon handling in rt2x00 as well.
This patch will move the function to the TX handlers,
and move all duplicate code into rt2x00queue.c.
After this change the descriptor helper functions
from rt2x00queue.c no longer need to be exported
outside of rt2x00lib and can be declared static.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 9 Jul 2008 12:40:37 +0000 (14:40 +0200)]
mac80211: revamp beacon configuration
This patch changes mac80211's beacon configuration handling
to never pass skbs to the driver directly but rather always
require the driver to use ieee80211_beacon_get(). Additionally,
it introduces "change flags" on the config_interface() call
to enable drivers to figure out what is changing. Finally, it
removes the beacon_update() driver callback in favour of
having IBSS beacon delivered by ieee80211_beacon_get() as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 9 Jul 2008 12:40:36 +0000 (14:40 +0200)]
mac80211: push interface checks down
This patch pushes the "netif_running()" and "same type as before"
checks down into ieee80211_if_change_type() to centralise the
logic instead of duplicating it for cfg80211 and wext.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 9 Jul 2008 12:40:34 +0000 (14:40 +0200)]
mac80211: make master netdev handling sane
Currently, almost every interface type has a 'bss' pointer
pointing to BSS information. This BSS information, however,
is for a _local_ BSS, not for the BSS we joined, so having
it on a STA mode interface makes little sense, but now they
have it pointing to the master device, which is an AP mode
virtual interface. However, except for some bitrate control
data, this pointer is only used in AP/VLAN modes (for power
saving stations.)
Overall, it is not necessary to even have the master netdev
be a valid virtual interface, and it doesn't have to be on
the list of interfaces either.
This patch changes the master netdev to be special, it now
- no longer is on the list of virtual interfaces, which
lets me remove a lot of tests for that
- no longer has sub_if_data attached, since that isn't used
Additionally, this patch changes some vlan/ap mode handling
that is related to these 'bss' pointers described above (but
in the VLAN case they actually make sense because there they
point to the AP they belong to); it also adds some debugging
code to IEEE80211_DEV_TO_SUB_IF to validate it is not called
on the master netdev any more.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sat, 5 Jul 2008 13:11:57 +0000 (15:11 +0200)]
rt2x00: Fix NULL pointer error in adhoc/master mode
As soon as an interface is enabled, and that interface is in adhoc or master mode,
the device will start raising beacondone interrupts. But before the first interrupt is
raised, mac80211 will probably not have send any beacons to the device yet, which
results in a NULL pointer error when the skb is being freed.
Note that the "raise beacondone interrupts without a beacon" is also a bug,
and will be addressed later. The more important bug however is preventing
the NULL pointer failt itself, since there might be other conditions that could trigger
it as well.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This corrects an error in the computation of the open loss interval I_0:
* the interval length is (highest_seqno - start_seqno) + 1
* and not (highest_seqno - start_seqno).
This condition was not fully clear in RFC 3448, but reflects the current
revision state of rfc3448bis and is also consistent with RFC 4340, 6.1.1.
Further changes:
----------------
* variable renamed due to line length constraints;
* explicit typecast to `s64' to avoid implicit signed/unsigned casting.
This fixes a bug in the logic of the TFRC loss detection:
* new_loss_indicated() should not be called while a loss is pending;
* but the code allows this;
* thus, for two subsequent gaps in the sequence space, when loss_count
has not yet reached NDUPACK=3, the loss_count is falsely reduced to 1.
To avoid further and similar problems, all loss handling and loss detection is
now done inside tfrc_rx_hist_handle_loss(), using an appropriate routine to
track new losses.
Further changes:
----------------
* added a reminder that no RX history operations should be performed when
rx_handle_loss() has identified a (new) loss, since the function takes
care of packet reordering during loss detection;
* made tfrc_rx_hist_loss_pending() bool (thanks to an earlier suggestion
by Arnaldo);
* removed unused functions.
RFC 4340, 7.7 specifies up to 6 bytes for the NDP Count option, whereas the code
is currently limited to up to 3 bytes. This seems to be a relict of an earlier
draft version and is brought up to date by the patch.
The TFRC loss detection code used the wrong loss condition (RFC 4340, 7.7.1):
* the difference between sequence numbers s1 and s2 instead of
* the number of packets missing between s1 and s2 (one less than the distance).
Since this condition appears in many places of the code, it has been put into a
separate function, dccp_loss_free().
Further changes:
----------------
* tidied up incorrect typing (it was using `int' for u64/s64 types);
* optimised conditional statements for common case of non-reordered packets;
* rewrote comments/documentation to match the changes.
Max Krasnyansky [Thu, 10 Jul 2008 23:59:11 +0000 (16:59 -0700)]
tun: Persistent devices can get stuck in xoff state
The scenario goes like this. App stops reading from tun/tap.
TX queue gets full and driver does netif_stop_queue().
App closes fd and TX queue gets flushed as part of the cleanup.
Next time the app opens tun/tap and starts reading from it but
the xoff state is not cleared. We're stuck.
Normally xoff state is cleared when netdev is brought up. But
in the case of persistent devices this happens only during
initial setup.
The fix is trivial. If device is already up when an app opens
it we clear xoff state and that gets things moving again.
Signed-off-by: Max Krasnyansky <maxk@qualcomm.com> Tested-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
xfrm: Add a XFRM_STATE_AF_UNSPEC flag to xfrm_usersa_info
Add a XFRM_STATE_AF_UNSPEC flag to handle the AF_UNSPEC behavior for
the selector family. Userspace applications can set this flag to leave
the selector family of the xfrm_state unspecified. This can be used
to to handle inter family tunnels if the selector is not set from
userspace.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Thu, 10 Jul 2008 23:52:52 +0000 (16:52 -0700)]
ipv4: fib_trie: Fix lookup error return
In commit a07f5f508a4d9728c8e57d7f66294bf5b254ff7f "[IPV4] fib_trie: style
cleanup", the changes to check_leaf() and fn_trie_lookup() were wrong - where
fn_trie_lookup() would previously return a negative error value from
check_leaf(), it now returns 0.
Now fn_trie_lookup() doesn't appear to care about plen, so we can revert
check_leaf() to returning the error value.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Tested-by: William Boughton <bill@boughton.de> Acked-by: Stephen Heminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Take out the confusing language in tcp_frto, and organize the
undocumented values.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Wed, 9 Jul 2008 22:06:45 +0000 (15:06 -0700)]
netfilter: nf_nat_snmp_basic: fix a range check in NAT for SNMP
Fix a range check in netfilter IP NAT for SNMP to always use a big enough size
variable that the compiler won't moan about comparing it to ULONG_MAX/8 on a
64-bit platform.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Wed, 9 Jul 2008 22:06:12 +0000 (15:06 -0700)]
netfilter: nf_conntrack_tcp: fix endless loop
When a conntrack entry is destroyed in process context and destruction
is interrupted by packet processing and the packet is an attempt to
reopen a closed connection, TCP conntrack tries to kill the old entry
itself and returns NF_REPEAT to pass the packet through the hook
again. This may lead to an endless loop: TCP conntrack repeatedly
finds the old entry, but can not kill it itself since destruction
is already in progress, but destruction in process context can not
complete since TCP conntrack is keeping the CPU busy.
Drop the packet in TCP conntrack if we can't kill the connection
ourselves to avoid this.
Reported by: hemao77@gmail.com [ Kernel bugzilla #11058 ] Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
If a mesh or ad-hoc interface is brought up and later it is replaced
by managed interface, the managed interface will keep transmitting
the beacons that were configured for the former interface. This patch
fixes that behaviour.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Tue, 8 Jul 2008 11:45:20 +0000 (13:45 +0200)]
rt2x00: Disable synchronization during initialization
As soon as init_registers() was called, the rt2400/rt2500
would start raising beacondone interrupts. Since this is highly
premature since no beacons were provided yet, we should
initialize the synchronization register to 0.
This will make all drivers initialize it to 0 regardless
if they are raising beacondone interrupts or not, since it only
makes sense to have it completely disabled.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the fast_start parameter from the rc_pid parameters
information and instead uses the parameter macro when initializing
the rc_pid state. Since the parameter is only used on initialization,
there is no point of making exporting it via debugfs. This also fixes
uninitialized memory references to the fast_start and norm_offset
parameters detected by the kmemcheck utility. Thanks to Vegard Nossum
for reporting the bug.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David S. Miller [Wed, 9 Jul 2008 05:49:00 +0000 (22:49 -0700)]
netdev: Kill qdisc_ingress, use netdev->rx_queue.qdisc instead.
Now that our qdisc management is bi-directional, per-queue, and fully
orthogonal, there is no reason to have a special ingress qdisc pointer
in struct net_device.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 9 Jul 2008 00:33:13 +0000 (17:33 -0700)]
netdev: The ingress_lock member is no longer needed.
Every qdisc is assosciated with a queue, and in the case of ingress
qdiscs that will now be netdev->rx_queue so using that queue's lock is
the thing to do.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 9 Jul 2008 00:18:23 +0000 (17:18 -0700)]
netdev: Move queue_lock into struct netdev_queue.
The lock is now an attribute of the device queue.
One thing to notice is that "suspicious" places
emerge which will need specific training about
multiple queue handling. They are so marked with
explicit "netdev->rx_queue" and "netdev->tx_queue"
references.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Acked-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Tue, 8 Jul 2008 22:36:57 +0000 (15:36 -0700)]
vlan: avoid header copying and linearisation where possible
- vlan_dev_reorder_header() is only called on the receive path after
calling skb_share_check(). This means we can use skb_cow() since
all we need is a writable header.
- vlan_dev_hard_header() includes a work-around for some apparently
broken out of tree MPLS code. The hard_header functions can expect
to always have a headroom of at least there own hard_header_len
available, so the reallocation check is unnecessary.
- __vlan_put_tag() can use skb_cow_head() to avoid the skb_unshare()
copy when the header is writable.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
After this we have an ifp->rt inserted into fib6 lists, but
queued for gc, which in turn can result in oopses in the
fib6_run_gc. Maybe some other nasty things, but we caught
only the oops in gc so far.
The solution is to disarm the ifp->timer before flushing the
rt from it.
Signed-off-by: Andrey Vagin <avagin@parallels.com> Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Although I only tested similar code (I don't use any of this wireless
code), the state maintainance between Netlink dump callback invocations
seems wrong here and should lead to an endless loop. There are also other
examples in the same file which might have the same problem. Perhaps someone
can actually test this (or refute my logic).
Take the simple example with only one element in the list (which should fit
into the message):
Larry Finger [Tue, 8 Jul 2008 14:43:43 +0000 (09:43 -0500)]
rtl8187: Change detection of RTL8187B with USB ID of 8187
Some early versions of RTL8187B devices have a USB ID of 0x8187
rather than the 0x8189 of later models. In addition, it appears
that these early units also must be programmed with lower power.
Previous patches used the Product ID string to detect this situation,
but did not address the low power question. This patch uses the
hardware version and sets the power accordingly.
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rtl8187: change rtl8187_dev.c to support RTL8187B (part 2)
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rtl8187: change rtl8187_dev.c to support RTL8187B (part 1)
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rtl8187: updating rtl8187_rtl8225.c to support RTL8187B
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / linux-2.6 / log